Search Documents

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

By J. Drelich

The highly-efficient and economically-feasible technology for bitumen recovery from US oil sands using a water extraction approach was developed at the end of the last century. This water-based bitumen extraction process has been optimized based on observations and analysis of microscopic mechanisms of bitumen release from oil sands and the bitumen transfer to a froth product as well as measurements of interfacial properties of bitumen. The wetting mechanisms that occur in the diluent-assisted water-based processing of US oil sands include bitumen film rupture and recession on sand grains and bitumen transfer to nucleated and injected gas bubbles. These mechanisms are reviewed in this contribution.

Jan 1, 2007

By Paul Swatkowski

A Note About Copyrighted Material ??Permission to Use? has been granted ?Teachthe7habits ?Think win/win (4thHabit) ?Don?t stop here ?i.e., buy the book

Jan 1, 2009

By Paikowsky, Samuel G.

"Due to the way drilled deep foundations are being constructed, their structural integrity and geotechnical capacity are highly variable. Drop weight systems are increasingly being used to dynamically test the capacity and integrity of drilled deep foundations. Conventional pile driving hammers are often either inadequate or not economical to test these foundations and drop weight systems have therefore been developed to allow for dynamic testing.The advantages of the tests include high mobility, short testing time, low cost relative to static load tests (allowing multiple tests at a single site), and integrity/construction quality evaluation concurrent with capacity determination. The dynamic testing method for drilled deep foundations encounter several difficulties including: the need for a pre-testing analysis for matching pile, soil and testing system, adequate mass and drop height to reflect the mobilized capacity without structural damage, test interpretations for irregularly shaped and/or non-uniform piles, need for reliable dynamic measurements depending on the impact and the distance between the impact and the measuring point, and limited knowledge about the accuracy of the predictions.The principles of the tests are presented using simplified models and demonstrated via a case history. Drop weight systems are reviewed. Dynamic measurement principles are explained and the construction and testing quality effects are outlined and demonstrated via numerical modeling and case histories. A comparison of dynamic and static tests is presented via a database, case histories and finally a short review of relevant codes is provided.1 IntroductionTraditional static axial load test is performed by a slow application of a force produced against independent reaction, imitating structural loading. It is the most reliable method to determine the pile’s performance as commonly required under typical service conditions. The major limitations of this testing are: (i) high cost associated with set-up, test duration, interpretation and construction delays, and (ii) inability to obtain information about the pile-soil interaction along the pile without additional testing means (e.g. tell tales, strain gauges, etc.). These limitations are acute when high capacity foundations are involved."

Jan 1, 2015

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

By D Gelling

Mineral sands dry plants consist of a large number of repetitive unit operations with significant transport delays, in the form of stream pipes, conveyors and elevators. As part of the P255 mineral sands sponsorship and using the JKMRC developed conductor/non-conductor (CNC) gauges, control loops have been implemented at the multi-duty dry plant of Cable Sands Limited at Bunbury. This paper describes the loops for kV control on a rougher high tension roll machines (HTR). The options available are product grade control and ratio control using the JKMRC CNC gauges, which measure the percent conductors in a stream. The purpose of control is to stabilise the circuit operation against disturbances such as atmospheric and feed disturbances.

Jan 1, 2001

By R. Adsero

The analysis of equipment trends in AUSIMM?s Revision of Monograph 19; Australasian Mining and Metallurgy Operating Practices (AMMOP) in the paper by Dight et al (in press) raised some interesting and in parts disturbing trends in the Open Cut Mining Industry. According to the US Bureau of Labour Statistics the US mining and petroleum industries? productivity is down by 12% since 2004 while the Australian Bureau of Statistics shows the productivity of the Australian mining industry is down by 34% since 2001. In terms of open cut equipment median output for draglines is down by 15% since 2003; electric rope shovels are down by 41% since 2003; hydraulic excavators are down by 39% since 2008; front end loaders are down by 39% since 2007 and trucks are down by 41% since 2006. Clearly the boom has not been good for the efficiency of the mines. During this same time, best practice (defined as the average of the top 10% by annual output per unit of input) has declined but not by as much as the median (eg. shovels down by 8%, excavators down by 19% and FEL?s down by 5%). This paper will build on the analysis of AMMOP to understand the differences occurring between median and best practice and identify the factors contributing to the decline in performance. As the industry enters a period of potentially lower prices for commodities and reduced margins pressure will be brought to bear on mine sites to start moving more with the equipment they have. An understanding of where efficiency has been lost will be a key component in that. The information contained in AMMOP, and the subsequent analysis of that information in papers such as this one will be crucial to reversing the decline in open cut equipment performance.

Feb 27, 2013

By D. B. Rebuli

Seismic networks in deep gold mines of South Africa are often planar owing to the tabular geometry of the orebody and, therefore, the mining infrastructure. Consequently, seismic event locations are poorly constrained in the direction perpendicular to the reef plane, and symmetrical locations above and below the reef plane may fit the observed data equally well. This problem may be resolved in situations where the strata above and below the reef plane have significantly different seismic velocities, which is the case for the Ventersdorp Contact Reef at Kusasalethu mine (previously Elandskraal, the amalgamation of Deelkraal and Elandsrand). A location method using a layered location model that takes into account the velocity contrast between the layers was tested. Observed direct- and head-waves were used to determine the velocity bounds of the P-wave velocities in the two-layer model. The data-set was also used to find the best P- and S-wave velocities for the two layers by grid searching over a range of velocities and minimizing the sum of the travel-time residuals. The results from the grid search and those from the calibration of velocities using direct- and head-waves give similar P-wave velocities for each of the two layers. A second set of seismic events was then relocated with this layered model and locations closer to reef were found. This simple layered location method goes some way to reduce the reefperpendicular location errors for Kusasalethu mine in particular. Keywords mine seismology, velocity model, location methods.

Jun 1, 2013

The banded iron formations "jasper bars," jaspilites, banded hematite quartzites or banded ironstones, etc., as they have. variously been termed in Western Australia, constitute one of the most striking features of the Pre-Cambrian in this State. They occur in at least two distinct divisions of the Pre-Cambrian, viz., in horizons interbedded with quartzites, shales and thin bedded dolomite in the N~llagine (Proterozoic) Series; and amongst the Older Pre-Cambrian rocks, associated with the metamorphosed sediments of the Jimperding-Chittering Series, the Yilgarn Whitestone Series and the Mosquito Creek Series, and interbedded with metamorphosed basic lavas, tuffs and sediments of the Older prenstone or Kalgoorlie Series.In the Hamersley Ranges in the north-west of Western Australia banded ferroginous cherts are well developed amongst the horizontal sediments of Nullagine Age. These iron formations have recently sprung into prominence as they have been found to form the host rocks for important deposits of· blue asbestos. They are closely comparable with the unique crocidolite-bearing banded ironstones of the Cape Province, South Africa, and have been described elsewhere in some detail by the writer. (1) t .The banded iron formations with which it is intended to deal principally in the following pages, form most abundantly in the Central and Eastern Goldfields of Western Australia where they form portions of the Older Greenstone or Kalgoorlie Series of auriferous rocks. In these regions their chemical inertness and physical hardness provide considerable resistance to the agents of erosion and consequently they frequently stand out in strong topographic relief in otherwise monotonously flat or gently rolling country. These banded-iron formations have proved of considerable direct economic importance in the goldfields and in other portions of the State because of thei!! associations with 'gold, iron -and to' a lesser extent, manganese; whilst indirectly because of their peculiar nature, form and topographic prominence, etc, they have been of tremendous assistance to the field geologist both in the practical application of methods of geological mapping and in the' elucidation of geological structures. Finally, they have recently acquired a new importance in the specialised search for ore-bearing lodes or for structural information over areas of soil-covered country, as their form and composition make them ideal subjects for the use of either electrical or m!1-gnetic methods of geophysical prospecting.

Jan 1, 1941

By D Woolmer

Since January 2019, BHP Olympic Dam have been trialling the use of a drone based LiDAR mapping system for the purpose for surveying stope voids. This new technology utilises Simultaneous Location and Mapping (SLAM) algorithm providing positioning, stability and collision avoidance in GPS denied environments. Implementation of this system utilised underground personnel trained in the equipment’s use. The study’s intention was to evaluate the effectiveness of this equipment versus traditional surveying methods in regards to quality, safety and productivity. The trial results showed a marked improvement in the quality, productivity and personnel safety when conducting surveys. The use of the drone and LiDAR system reduced personnel and equipment requirements for surveys, thus allowing these resources to be deployed elsewhere. The technology’s simple and rapid deployment allowed multiple surveys to be conducted during a 12 hour shift, including ad-hoc work with minimal disruption to underground operations. After the drone’s initial trial, further work was conducted to utilise the Hovermap LiDAR scanner on other platforms to increase utilisation. A mounting system was created allowing the LiDAR to be mounted on a remotely operated loader or vehicle. This enabled drawpoint scans to be taken directly after production completion, resulting in faster stope close outs and drive scans for convergence monitoring. Implementation of the LiDAR system has resulted in improvements in the stope production cycle by reducing delays previously associated with data capture. The increase in the volume and quality of data has also allowed in-depth back-analysis of stopes in new mining areas to be conducted, which have driven improvements in the design process.

Mar 15, 2021

By Klaus Tietz, Hamish Adam, John Selby, Ian Glazier, Brian Sinfield

"Room-temperature tunable diode laser (TDL) analyzers are gaining in acceptance for highly critical safety monitoring applications in a variety of industries. This paper describes the testing, evaluation and deployment of a laser-based hydrogen cyanide monitoring system at the Campbell Complex of Goldcorp’s Red Lake Gold Mines in Balmertown, Ontario, Canada.A trial, single channel installation was followed by a staged multi-channel installation. Unexpected technical issues with the multi-channel installation were addressed and resolved.INTRODUCTIONLaser-based gas detection has several advantages over existing gas detection techniques (Ballangrud, 1993; Silver, 1992; Bomse, 1995; Table 1). For practical purposes, lasers generate light at a single wavelength. Room temperature tunable diode lasers (TDL) emit light in the near infrared (NIR) part of the electro-magnetic spectrum. Many gases of interest, including HCN, NH3 and others, absorb energy in the near infrared (NIR). Each gas has a unique absorption signature, or spectrum, made up of a large number of individual “absorption lines”. A TDL can be tuned to select a single absorption line of a target gas, which does not overlap with absorption lines from any other gases. Therefore, laser gas sensing is selective and does not suffer from interference from other gases. The single-wavelength nature of laser light also means that laser gas analysers have a linear response over a wide dynamic range.Tunable Diode Lasers (TDL) generate only a few mW of power. However, all this power is concentrated at one wavelength, the wavelength where gas absorption occurs, resulting in high signal-to-noise ratios and short response times, typically of about 1 or 2 seconds (Ballangrud, 1993). This also means that long path lengths can be used, enabling accurate measurements of very low concentrations, even with weakly absorbing gases. Tunable Diode Lasers provide all the advantages of other semiconductor devices: they are small, solid-state devices, operate at room temperature, and have long-term reliability (over 15 years). Currently, they can be obtained for any wavelength throughout the NIR (700nm to 2000nm). Because many gases absorb in the NIR, the technique is widely applicable."

Jan 1, 2011

By Luke Meers

Roadway development rates in Australian underground coal mines are failing to keep pace with modern longwall systems and are unlikely to sustain further improvements in longwall productivity into the future unless step change improvements to roadway development equipment and practices are made. Bottlenecks which limit and constrain improved production and impact the safety of operators have been identified through a series of industry surveys, with the manual installation of strata support materials, consumables delivery, coal haulage and monorail installation being highlighted as major areas to improve development performance. This paper looks at research being carried out at the University of Wollongong in designing an integrated system approach for the fully automated handling and installing of development consumables, and the systems required to support these activities. A series of hard automation manipulation devices have been demonstrated in surface trials and the results indicate that rapid roadway development can be achieved.

Aug 1, 2013

By Richard K. Sandaas

Start Date: April 4, 1988 Completion Date: Dec. 29, 1989 Contractor: SCI Contractors Past and present transportation centers will come together at International District Station, located at the south entrance to the tunnel next to the turn-of-the-century Union Station train depot. The area will bustle once again with activity as commuters and visitors converge on the modern transit station at the edge of Seattle's International District. Buses coming from south Interstate 5 and Interstate 90 will enter the tunnel through this station. [ ] International District Station is an open-air station, 1,060 feet long and 82 feet wide (about 15,400 cubic yards of concrete were used to build the station). A concrete lid over the southern portion of the station staging area is held in place by 131 support piles. The station will include entrances on Jackson Street and King Street. Union Pacific Realty is planning to build an office and retail complex upon the lid. The station also has an international flair. Symbols of the Chinese zodiac will be etched into the station plaza floor. The station platform walls will be lined with large steel panels embellished with designs in origami?a Japanese folded paper art form. [ ]

Jan 1, 1990

By A. S. Watts

The Bureau of Mines has been conducting an investigation of the feldspar resources of the New England and North Appalachian States with a view to greater efficiency and economy in their utilization. Such an investigation was deemed necessary, not only because of the continued and increasing consumption of these minerals, but especially because of the demand for better technical control of the raw materials that are used by the white-ware industries of the United States. Most manufacturers of white pottery wares have only a limited knowledge of the origin, mode of occurrence, and methods of mining and preparation of the materials that they use. Heretofore, owing to a belief that the supply of raw material was unlimited, the manufacturer had concerned himself chiefly with the solution of the problems of manufacture. Within the past few years, however, it has been found that difficulties arise in manufacture which can be traced beyond the manufacturing process and are believed to be due to a need of better control of the materials used. Furthermore, as competition becomes more severe, more attention must be paid to selection of materials in order to minimize consumption and also to avoid unnecessary expense for transportation of material. Doubtless the lack of interest as regards these details has arisen from the fact that in the past a considerable proportion of the whiteware ingredients has been imported and the manufacturer has been forced to rely on the samples submitted and the general uniformity of the source of supply to insure against variation of the material. An extra precaution arising from this lack of definite knowledge still prevails in the common practice of never depending on one source of supply for anyone ingredient. Often the products of three or more producers are blended so that if anyone shall vary without warning the variation arising from its use will not be sufficient to ruin the ware.

Jan 1, 1916

By James O'Brien, Lyman Frost, Grant Hawkes, S. Elangovan, Manohar Sohal, J. S. Herring, Joseph Hartvigsen, Carl Stoots

"Pressing environmental and energy security concerns have brought much needed attention to economic production of hydrogen as the secondary energy carrier for non-electrical markets as well as to meet increasing demand for crude upgrading and desulfurization. While steam reforming of natural gas is currently the dominant method of hydrogen production, it is depleting a valuable fossil fuel while emitting green house gases. Thus, in the long run, efficient, environmentally friendly, and economic means of hydrogen production using nuclear and renewable energy needs to be developed. High temperature electrolysis using solid oxide electrolyte cells is an exceptionally efficient means of generation of high purity hydrogen. It is also capable of directly converting steam and CO2 into synthesis gas. This co-electrolysis process enables conversion of CO2 recovered from concentrated industrial sources into a feedstock for synthetic fuels production. Use of CO2 provides a means of storing hydrogen in a concentrated and convenient form – a hydrocarbon. This is also an effective storage medium for intermittent renewable energy sources such as wind and solar.Ceramatec, Inc and the Idaho National Laboratory are applying solid oxide fuel cell technology to the production of synthesis gas by high temperature co-electrolysis of steam and carbon dioxide. This technology utilizes solid oxide fuel cell stacks to electrochemically remove oxygen from steam and CO2, leaving a clean stream of hydrogen and carbon monoxide suitable for fuel synthesis. By varying the relative concentrations of carbon dioxide and steam, the hydrogen to carbon monoxide product ratio can be controlled as required by the desired type of synthetic fuel being produced from the syngas. The resultant synthesis gas has been used as the feedstock to produce synthetic methane and Fischer Tropsch liquid fuels.Alkaline and proton exchange membrane electrolysis cells typically operate below 100°C, while solid oxide electrolysis cells operates in the 750-850°C range. This higher temperature improves the efficiency significantly. Practically, it translates into a lower cell operating voltage, 1.1-1.4V for high temperature electrolysis vs. ~1.8V for water electrolysis. Hydrogen production is stoichiometric with current in all types of electrolyzers.Carbon dioxide is a valuable resource as a feedstock for energy storage as a hydrocarbon. There is a vast amount of renewable energy that cannot be effectively utilized as grid electricity, but which could be used to convert CO2 to hydrocarbons, offering a solution to the even more difficult (than supplying grid power) challenge of production of sustainable, domestic transportation fuels. Conventional electrolysis and chemical processes could be deployed to accomplish this conversion. However, high temperature co-electrolysis of CO2 and steam to produce synthesis gas using solid oxide fuel cell technology has the potential of improving the efficiency by nearly 50%. A domestic synfuel industry will enable a much larger reliance on intermittent renewable energy than can be accommodated by conventional electric demand profiles while increasing our energy security."

Jan 1, 2010

The mining industry has recognised for some time the importance of supporting programs which serve to educate the Australian public about the socio-economic benefits of mineral resource development. More recently, industry leaders have realised that the future development of the industry will depend on attracting sufficient young people to commit to a career in the industry. Apart from lending support to the traditional education institutions in Australia, the industry now has the opportunity to participate in the development of education programs in museums. Whilst historic, mining-related theme parks such as Sovereign Hill and Coal Creek in Victoria serve very effectively the objective of relating past mining activities to the socio-economic development of Australia, there still exists the need to provide a facility which, under the same roof, excites interest in geology, mining, mineral processing and the role of minerals and energy in modern society. The redeveloped Geological and Mining Museum (the "Mining Museum"), which is located in The Rocks area of Sydney, meets this objective. With the central themes of formation and transformation this new Museum, which aims to be the best of its type in the world, will use modern museum exhibit techniques and the resources of the Minerals and Energy Information Centre to educate the community including teachers and school children. In the best tradition of museums, outstanding mineral and other collections will complement a comprehensive range of interactive, high technology exhibits which will include a number of exploratory "hands on" facilities. Australian companies are joining with Government to fund this exciting new museum. There is still a need for industry professionals to realise that a modern "mining" museum is no longer just a repository for objects of mining heritage but is also an important centre which serves as an important educational and public relations interface. The Education Section of the new "Mining Museum", which is linked closely with the new Minerals and Energy Information Centre, will be working closely with appropriate mining-related Tertiary institutions to develop specific career programs aimed at secondary students who wish to pursue a career in the mineral resource industries.

Jan 1, 1989

By C. R. Copeland

Water sprays are a common method used to reduce particulate matter (PM) emissions. Various factors such as wettability, surface area coverage, fine particle engulfment rates, interparticle adhesion forces, suppressant penetration and suppressant longevity have all been suggested as critical factors in achieving effective PM control. However, it has not been established which of these factors are the most important. Experimental work indicated that suppressant penetration is the most critical of these factors. The length of time after application that suppressants were effective was also improved by using hygroscopic reagents that retained moisture to prevent evaporation. Maximizing suppressant penetration and improving suppressant longevity led to an average 86% reduction in PM10 concentrations in laboratory dust tower tests.

Jan 1, 2008

By Maurizio Siepi, Fabio Santillan, Lyndon Bedford, Carlo Crippa

"Abstract: Wolf Creek dam, on the Cumberland River in Kentucky, US, operated and maintained by the Nashville District of the USACE, is the Corps' largest reservoir east of the Mississippi river. The 1748 m (5,736 ft) long Wolf Creek dam combines earthfill and concrete gravity sections. Construction began in 1941 and was completed in 1950. The dam showed signs of instability in the 1960’s, and in the late 70’s an in-depth project of rehabilitation was undertaken, using both grouting and secant piles. The works saved the dam, but in the late 90’s further signs of distress worried the Nashville district of USACE which, after a study conducted on the water seepage, concluded that construction of a new concrete barrier cut-off wall was needed. In 2009, the $341.4 USD million contract was awarded to TREVIICOS-SOLETANCHE JV.The new wall, located upstream of the concrete monoliths, has a minimum thickness of 60 cm (24 in.), and runs the length of the embankment, into the right abutment, for about 4,200 feet. The founding depth reaches 84 m (275 feet), well below the zone of solutioning. With a total surface approaching 92,903 sq.m (1,000,000 sq.ft), the Wolf Creek barrier wall is unlike any other project in the world.The construction of the cut-off wall followed a complicated but logical sequence of several operations, involving a variety of technologies: grouting, hydromill, directional drilling, and secant piles with reverse circulation. The intensive rock grouting program was aimed to minimize the risk of slurry loss and extend the positive cut-off further deep. Subsequently, an Encasement Concrete wall was installed with hydromill, toeing into the rock, to protect the embankment during the following phases. Smart holes were then drilled into the Encasement wall down to the final depth. Eventually, the holes were used to install the secant piles by employing the reverse circulation piling method.An extensive verification campaign has confirmed the superior quality of the cutoff wall consisting of 1200 secant piles, exceeding by far USACE’s requirements. The main project was substantially completed in early 2013. A small portion of secant piles wall will be installed downstream of the dam, to close the switchyard, finishing the project in the early months of 2014.IntroductionWolf Creek Dam is located on the Cumberland River in south-central Kentucky. The Nashville District of USACE operates this multipurpose dam to provide hydropower, flood control, water supply, and water quality benefits for the Cumberland River system and surrounding region. Lake Cumberland, created by the dam, impounds 7,400 million cu.m (6 million acre foot) at its maximum pool elevation of 232 m (760 ft) above sea level. This lake is the largest reservoir east of the Mississippi and the ninth largest in the United States, and attracts 4.89 million visitors, more than Yellowstone National Park (2.87 million).This paper describes the recently completed works for the rehabilitation of the dam, accomplished by TreviICOS-Soletanche JV with the construction of a new Barrier Wall."

Jan 1, 2014

By R. Altindag

In rock cutting mechanics, the effects of the rock and coal brittleness on the efficiency of cutting bits are examined by many researchers. There is no universally accepted brittleness concept as a measure of cutting efficiency. The effect of the brittleness on rock cutting has not been completely explained. The aim of this study is to correlate the relationships between Specific Energy (SE) and brittleness concepts. The applicability of various brittleness measurement methods for rock cutting efficiency has been investigated. In this study, the raw data derived from previous experimental studies were used, and the relationships between SE and brittleness concepts were investigated. The two previously used brittleness concepts, which are named as B1 (the ratio of compressive strength to tensile strength) and B2 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), and a new introduced brittleness concept named B3 (the area under line in relation to compressive strength and tensile strength) were evaluated in this study. The relations among these brittleness concepts for rock cutting efficiency were established using regression analysis. There is no correlation found between the SE values and the brittleness of B1and B2values. But, the SE is strongly correlated with the brittleness of B3. It was seen that the suggested brittleness of B3concept could be used as an indicator in rock cutting efficiency analysis.

Jan 1, 2003

By Wenbing Xie

At Renlou Coal Mine, Huaibei Mine Area, the track entry deformed significantly after longwall mining in an overlying multiple seams. The supporting characteristics of primary roof bolts and shotcrete with wire mesh are closely related to the movement of the mine?s surrounding strata. A case study of a track entry deformation was monitored during the longwall mining of a selected overlying panel. The measured data showed the unique entry deformation pattern during the longwall mining in the overlying seam. Underground extensometer measurement showed that entry stability was mainly affected by the periodic roof weighting of longwall mining in the overlying seam. The displacement of the deeper strata occurred a head of the immediate vicinity of the entry. Thereafter, deformation of the roof and floor strata was in the form of shearing of the shallower strata. Due to the use of heavy-duty roof bolting with wire-mesh, the roof-tofloor and rib-to-rib convergences were small, but the floor heave was large, greater than 80% of the roof-to-floor convergence. The measured displacement from extensometers varied with the position of the monitored cross-sections and depth into the roof. There were several deformation patterns, such as shearing movement, compression, and expansion, and the variations between compression and expansion. Strata compression at the entry surface was always accompanied with shearing movement at the deeper strata. During the longwall mining, the whole surrounding strata of the entry moved toward the opening. Underground practical experience indicated that prior to mining, the entry was supported very well in excellent conditions. After mining, however, it deformed greatly. The current entry support technology was not effectively control the severe deformation incurred in entries driven in soft strata due to the following reasons: (1) little is known about the entry deformation behavior of the strata surrounding the opening and (2) the degree of interactions between entry deformation and roof bolting with wire mesh is not well understood. Consequently, effective supporting systems cannot be properly selected to control its deformation and maintain a stable supported surrounding structure.

Jan 1, 2012