Search Documents

By N. A. Eilertsen

Mining operations were in progress at the Shawangunk mine near Summitville, Sullivan County, N. Y. as early as 1843 and again as late as 1918. Difficulty in effecting mechanical separation of sphalerite and galena was the primary reason for abandonment by various operators. The Bureau of Mines investigated this mine by diamond drilling, sampling, and performing beneficiation tests. The investigation included the construction of 1.25 miles of access road and the completion of 6,526 feet of core drilling in 24 holes. In addition, 151 samples were taken in the mine. The investigation proved an extension of ore contiguous to the old mine workings and resulted in the discovery of another ore shoot at depth. The ore occurs as fissure filling in a fault zone and contains concentrations of zinc and lead sulfides with minor dissemination of chalcopyrite in a quartz gangue. Metallurgical tests indicate that the ore can be concentrated by selective flotation.

Jan 1, 1950

By Yijun Caoa, Xiuxiang Taoc, Zhongbo Hub, Yinfei Liaoa

A new preparation scheme for a difficult-to-float coking coal from the Kailuan Mine, Tangshan, China was investigated. The results showed that grinding followed by column flotation was beneficial for obtaining products with low ash content. The positive effect of grinding on the coal floatability is attributed to the liberation of intergrowths and coal surface improvement. Tests indicated that 10 minutes was the optimum grinding time, and over grinding resulted in a deterioration in flotation performance. With a grinding time of 10 minutes, conventional flotation had potential to yield a product with around 12.42% ash content and 69.15% combustible recovery. Column flotation can reduce the product ash content to 11.15%and increase combustible recovery to 74.47%. Consistently better flotation results reveal that column flotation is more efficient than conventional flotation for such fines.

Jan 1, 2015

By Mark Fernald, Christian O’Keefe, John Viega

"In this presentation, the SONARtrac™ technology platform will be described. CiDRA's proprietary clamp-on, passive sonar array-based flow meter technology performs two independent measurements – flow rate and fluid characterization. Firstly, the meter provides the volumetric flow rate of the mixture by measuring the speed at which naturally occurring turbulent structures convect with the flow past an axial array of sensors. Secondly, the meter uses similar sonar-based processing techniques and naturally occurring sound in the process fluid to measure entrained air levels. The result is a unique ability to measure the flow rate and entrained air level of most fluids – clean liquids, high solids content slurries, and liquids and slurries with entrained air.Also to be presented is the application of the sonar-based technology platform in a variety of oil sands processes, hydrotransport, and minerals beneficiation applications. In particular, difficult slurry flow measurement and control in the areas of comminution and flotation such as mill discharge, hydrocyclone feed/overflow, final concentrate, thickener discharge, and tailings will be discussed. In addition new real time maintenance free process measurement capability will be presented in the areas of entrained air in slurry, collection zone gas holdup (?g), and slurry velocity profiling. The operational advantages and value of these measurements, even in the presence of scale buildup, will be discussed.INTRODUCTIONFlow measurements in the mineral processing and oil sands industry suffer from the limitations placed by previously available flowmeters including the commonly used instruments such as ultrasonic meters, magmeters, turbine meters, orifice plate meters, vortex flow meters, Coriolis flow meters, and venturi meters. The desire or requirement to make a non-contact measurement that is accurate and robust, and can be performed on practically any type of fluid within practically any type of pipe has driven the creation of a new class of flowmeters. This new class of flowmeter technology utilizes sonar-based processing algorithms and an array of passive sensors to measure not only flow, but also fluid composition."

Jan 1, 2007

By I. C. Spangenberg

The status of sampling practices in the gold mining industry in Africa was determined as an initial step in a process to standardize sampling practices in the mining industry. Twenty-one gold mines, twenty metallurgical plants, and thirteen laboratories were rated for the potential influence of the relevant sampling errors on each component of the particular sampling system. The findings of the study on the status of equipment, standards, procedures, and management principles were presented in a dissertation (Spangenberg, 20121) and are now used by AngloGold Ashanti?s mines in the quest for correct sampling practices. The information is also used to compile a guideline on leading practice procedures for sampling methods in gold mining. This article is an overview of sampling best practice found in African mining Keywords theory of sampling, best practise, sampling errors, sampling standards.

Jan 1, 2014

By Y Li, D J. Williams, E Topal

A mine waste rock dump does not have any intrinsic value, yet is an inevitable structure in surface mining operations. Since the purpose of mining is to maximise profit, possible expenditure reduction in hauling waste rock to the dump, which can represent up to 50 per cent of the total operating cost, is highly desirable. Apart from cost, potential acid mine drainage (AMD), due to seepage from surface waste rock dumps containing reactive waste rock, could threaten the ecological balance, drinking water supplies and irrigation systems downstream from a mine site. In order to minimise these potential risks, selective placement of benign and reactive waste rock, and the encapsulation of reactive waste rock by benign waste rock, need to be carried out during the construction of the rock dump.In this paper, a new methodology, based on mixed integer programming (MIP) is developed to manage waste rock dumping. The model aims to minimise waste rock haulage costs by locating the optimum destination(s) for each waste rock block, while at the same time controlling the placement of reactive waste rock to minimise the potential for AMD. Tests on small-scale virtual data demonstrated that the model is capable of dealing with selective placement of different waste rock types, encapsulating reactive, potentially acid forming (PAF) waste rock, and stockpiling benign waste rock for encapsulation and rehabilitation purposes. The solution time for the MIP model is far less than the traditional manual approach, and the resulting schedule is up to 46 per cent more cost effective.CITATION:Li, Y, Topal, E and Williams, D J, 2012. Mathematical approach for better mine waste rock dumping management, in Proceedings Life-of-Mine 2012 , pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By N. A. Karl, D. R. Wilburn

"This summary of international mineral exploration activities for the year 2015 draws upon information from industry sources, published literature, SNL Metals & Mining (SNL) (Charlottesville, VA) database and specialists in the U.S. Geological Survey (USGS) National Minerals Information Center. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry, and presents analyses of exploration activities performed by the mineral industry.Three types of information are reported and analyzed in this annual review of international exploration: budgetary statistics expressed in U.S. dollars provided by SNL; regional and site-specific exploration activities that took place in 2015 as compiled by the USGS; and regional events that affected exploration activities including economic, social and political conditions, which were derived from published sources and discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources were used to develop commodity and regional compilations, statistics may vary depending on the source and type of data that are being reported.The SNL data summarize planned company budgets for worldwide exploration activities in 2015 for 24 nonfuel mineral commodities and metal alloys and are based on company surveys. Surveys focused on precious metals (gold, platinum-group metals and silver), base metals, (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (bauxite, chromite, iron ore, manganese, phosphate and potash), and other commodities (diamond, graphite, heavy-mineral sands, lithium, niobium, rareearth elements (REE), tantalum, tungsten and uranium).USGS data compilations and analyses are based on information provided by USGS mineral commodity and country specialists, as well as industry contacts and published trade journals. The USGS data summarize exploration site data collected for more than 80 minerals and materials, with a focus on base metals, diamond and precious metals. The USGS analyzed available information to assess the level of exploration activity in 2015 and to report trends in mineral exploration activity for the period 2005 through 2015. These analyses identify where mineral exploration is occurring by commodity and region and the intensity of activity that is taking place in each region for selected mineral commodities, and determines those factors that most affect changes in exploration activity."

May 1, 2016

By Ebrahim Tarshizi, Livernois Ryan, Emily Sarver, Zoe Scopa, Robert Setterlind, Leah Frost

"The mines of the future present a host of challenges, which may appear exciting or daunting, depending on one’s perspective. Whether some sectors of the public recognize it or not, the demand for raw resources is not going away any time soon. In fact, it is rising, as the global population grows, urbanizes and attempts to steadily increase quality of life. Yet, at the same time that much of the highly developed world is calling for greener goods, reduced consumption and cleaner production, in other areas there are cries for clean water and sanitation, consistent energy supply, access to health care and education, personal security and support for basic human rights. The balancing act for sustainable development of our global society is, indeed, precarious and the mining community is a key player. Fortunately, many industry members have accepted this role and the responsibility to provide leadership and a solid foundation for progress. Looking ahead, we need new generations of leaders, including many mine engineers who are ready to tackle all sorts of complex problems.There are tremendous needs just for technological innovations. Increasingly tough deposits will require that the industry continues to expand scale toward “mega pits” and “super caves;” fully develop unconventional recovery techniques like in situ leaching and gasification or deep-sea extraction and seriously consider off-earth endeavors. Such work will take entirely autonomous equipment, novel separations, processing and recycling methods, and systems that can withstand extreme physical conditions, just to name a few. It will also take a level of systems integration never-before seen in the mining industry, complete with big data issues, sophisticated predecitve analytics and modeling efforts and cyber-security challenges.Moreover, increasingly complex environmental problems will require creative solutions. Addressing issues like pollution control across multiple media, emerging contaminants, optimal management of wastes, selective mining and shared use of resources between mine operations and surrounding communities and ecosystems are among the top priorities. Really, a complete paradigm shift must occur, such that the focus is on overall improvement of environmental conditions, rather than minimization of impacts. A similar shift will be required in the social realm. How can miners be safer and healthier on-site and off? How can the industry contribute to communities such that they are better off, now and longterm, for having a mine next door? How can artisanal mining practices be transformed to also contribute to sustainable development? How can the industry’s work be a factor in increasing economic and political stability? How can the public understanding of raw resources and the need for mining enterprises be improved?Given the coming challenges, there is no doubt that the mine engineers of the future will need highly diverse skillsets — meshing traditional and contemporary competencies to a degree not previously considered in mining, or most others fields. To be sure, the scope and scale of mining projects make them wholly different than most other engineering work, aside from perhaps the largest civil and urban development projects. While on-the-job experience will continue to be essential, formal education programs (i.e., at post-secondary institutions) must lay critical groundwork."

Jan 6, 2017

The unpaved road network on a surface mine is extensive, comprising numerous roads of varying construction and material qualities with highly variable traffic volumes. Existing haul road maintenance management systems (MMS) work well for predictable traffic volumes, but for complex mine road networks, the MMS becomes onerous. This results in sub-optimal road maintenance strategies with the attendant increase in total road-user costs and reduction in service. A real-time maintenance management system was thus sought to overcome the deficiencies of existing MMS for mine roads. Since most large mines operate trucks with on-board diagnostic data collation, linked through a centralized communication and GPS backbone, it was proposed that road condition could be monitored on a real-time basis through on-board vibration signature analysis. The aim of this paper is to present the development of a real-time mine haul road maintenance management system. Following are view of mine road maintenance practices, the real-time system architecture is introduced and the results of a field trial of on-board vibration signature assessment is presented. The trial results are discussed in the light of road defect signature recognition, analysis, signature repeatability and system limitations. This approach has applicability to other situations such as a network of district roads, subject to an analysis of the economic feasibility. The paper concludes that modern technology has the potential to apply maintenance as and where needed with possible reductions in authority cost and an improvement in service provided for the road user.

Jan 1, 2003

By J. H. Maritz, Uludag. S.

"*Paper written on project work carried out in partial fulfilment of B.Eng(Mining Engineering) degreeAfriTin Mining Limited plans to reopen the Uis tin mine in Namibia and establish a pilot processing plant for phase 1 of the Uis tin project, which is scheduled to commence in the last quarter of 2018 . A mining plan is required for phase 1 to supply the new pilot processing plant with 500 kt of run-of-mine ore per annum, for a period of 5 years. New geological mapping and three-dimensional modelling of the mining area were utilized to identify the most optimal mining locations that require low initial waste stripping. An open-pit mining method was selected to target the surface outcrops of the pegmatite orebodies. The mine design criteria were determined and used as input to generate the mine design by utilizing professional engineering software. The mine design was optimized and an overall stripping ratio of 0.81 was achieved. A 5-year production schedule was developed for the mine design according to quarterly periods of three months. A fixed production target of 125 kt of ore was assigned to the quarterly periods, and a ramp-up production target of 65 kt of ore was assigned for the first period. The mobile mining equipment requirements were calculated, and recommendations were made for implementing the 5-year mining plan. IntroductionAfriTin Mining Limited is the owner of the Uis tin project in Namibia and plans to reopen the Uis tin mine, which is located near the town of Uis, approximately 164 km north of Swakopmund. The Uis tin mine was owned and operated by Imkor Tin, a subsidiary of Iscor South Africa. Mining commenced in 1958, and the operation was closed in 1991. Steffen Robertson & Kirsten (SRK) defined the life of mine (LOM) plan for the historical Uis mine in 1989. The SRK report estimated the historical resources and reserves, which consisted of sixteen cassiterite-bearing pegmatite orebodies. SRK developed the most economical pit designs to provide the highest average tin grade at the lowest practical waste stripping ratio. Exploration data from the SRK report of 1989 was used extensively throughout this study, since no new exploration drilling has been conducted. The pegmatites are present as large, subvertical and outcropping veins up to 100 m in thickness. Once phase 1 is operational, mining will be conducted using conventional open pit mining methods. Initial production will be from exposed pegmatite veins in the old mine workings. AfriTin plans to establish a pilot processing plant by the end of 2018 to beneficiate run-of-mine ore at a rate of 500 kt per annum."

Jul 1, 2019

By Q Johnston

Since its inception in 1990, improved metallurgical processing technologies, coupled with mine planning enhancements and improved geological knowledge, have sequentially enabled better efficiencies and economies of scale at the Macraes Gold Project. Over a period of 11 years, processing enhancements have been achieved by: +        increasing mill throughput, from one million tonnes per year, to current throughput of 3.9 million tonnes per year; +        improving recovery rates, from 70 % to approx 84 %; and +        performance enhancement through innovation, eg the use of kerosene to combat ClL pregrobbing. Future processing improvements have been identified in optimising the ore feed and processing flowsheet. The introduction of the autoclave has transformed the process flow form a traditional 'mill headgrade and tonnes milled' operation, to a 'sulphur/gold ratio and sulphur tonnes oxidised' operation.

Jan 1, 2001

Flow Sheet Simulation of Municipal Waste Treatment Processes

Sep 13, 2010

By S. Sun

The equilibrium distribution of Cu, Fe and Ni between Cu-Ni-Fe mattes and Pt alloy was measured as functions of the sulphur partial pressure (pS2), oxygen partial pressure (pO2),temperature and Fe content of the matte. The distribution ratios of Cu, Fe and Ni between matte and alloy were independent of oxygen pressure when the pS2was fixed at 2.5x10-5atm and pO2was varied between 10-15and 10-12atm. The distribution ratio of Cu, Fe and Ni increased as the sulphur partial pressure increased. The Cu and Ni distribution ratios decreased with increasing temperature and the Fe distribution ratio increased slightly over the temperature range of1350?1500°C. For mattes where the proportions of Cu and Ni were kept constant, the distribution ratio of Cu increased as the Fe content in the matte increased. The Fe and Ni distribution appeared to be independent of the iron content in the matte and had a value of 1.2 and 1.6 respectively. The activity of Cu, Fe, Ni in the matte was calculated using a regular solution model for solid Pt-Fe-Ni-Cu alloy. The activity coefficient of Cu, Fe and Ni decreased as pO2and pS2increased.The activity coefficients also appeared to be independent of the Fe content and temperature over the range of 36 to 54 wt% iron and 1350 to 1500°C respectively. Keywords: activity, alloy, matte, thermodynamics

Jan 1, 2004

By David Preece

The Thirlmere aqueduct was constructed over 110 years ago to provide water from the Lake District (in the north-west of England) to the city of Manchester some 60 miles (100 km) away. The aqueduct remains, to this day, a key piece of infrastructure in the distribution of raw water in the north-west of England. A short section of the aqueduct was identified as being in poor condition during routine inspections by the owner. Subsequent investigations attributed the conduit damage to the movement of unstable ground over the conduit. Bachy Soletanche Ltd was subsequently appointed to carry out the design and construction of the slope stabilisation works and to undertake repairs inside the damaged conduit. The works were undertaken on an existing slope which, in places stands at a gradient of up to 40º to the horizontal. Strict limitations on plant and equipment were imposed by the client (United Utilities) to ensure that slope and conduit loading and associated vibrations were kept to an absolute minimum during construction. An intensive instrumentation system was installed to monitor surface movements, ground movements at depth, conduit movement and strains across existing planes of weaknesses within the conduit. The solution comprised the installation of spaced piles up-slope and down-slope of the conduit. Restrictions were imposed on the minimum stand-off distance between the outside face of the conduit and the piling works so targeted permeation grouting was undertaken to improve the ?connection? between the conduit and the down-slope piles. The presence of existing sub conduit groundwater flows was suspected and the permeation grouting was focused in areas to minimize disruption to the groundwater regime. The paper presents the basis of the design and highlights the combined construction and instrumentation methods adopted to minimise damage to this valuable asset.

Jan 1, 2011

By M. Abdellatif

The production of a 40% Al-Ti alloy was successfully proven at the lab scale, using pure TiO2, aluminium, and lime. These tests were conducted in an induction furnace maintained at 1600?16250C. The introduction of rutile into the feed recipe resulted in an alloy containing between 0.35 and 1.10% Zr, depending on rutile to TiO2 ratio. DC arc production of the alloy was largely accomplished at 40 and then 200kW scale. These tests evaluated various metallurgical and operational factors including target slag composition, Ti-content in the alloy, co-feeding versus sequential, furnace bath depth, and rutile as part of the Ti containing feedstock. Overall, an alloy containing 24?33% Ti was consistently produced with co-feeding of the reactants and with lower taphole tapping. When rutile was added, the zirconium analysis in the alloy remained below 0.2%. The main impurity elements were iron, silicon, carbon, nitrogen, and oxygen.

Jan 1, 2009

The work to be described is part of a comprehensive research on the influence of impurities on the properties of lead. The author had previously compared an electrolytic lead containing less than 0.002% total impurities with a commercial lead containing 0.008% impurities (excluding oxygen) and had shown that the former recrystallised more readily than the latter under the same conditions of cold work and annealing. This difference in properties was attributed to the difference in purity. Electrolytic lead containing only 0.0005% total impurities has been prepared and cast in vacuo. Some interesting effects have been obtained by working and annealing this lead, and by adding silver to it. The preparation of this lead, and the effects obtained thereon, are described in this paper. Thepaper is divided into the following sections:(I) Preparation of electrolytic lead.(II) Vacuum Casting.(III) Effect of Cold, Work and Annealing on two Electrolytic Leads, having 0.002% and 0.0005% Total Impurities respectively.1 Research Fellow, Dept. of Metallurgy, University of Melbourne.2 Proc. Aust. lnst. Min. Met., 1932, 87, 145.

Jan 1, 1934

By A. J. MacRae

Metallurgical furnaces are made up of complex multi-component systems that must function either together or in parallel for safe, and reliable operation. Thermal expansion of single material components experience induced stresses during heating and cooling, which can lead to cracking or failure. Multi component elements and systems can experience significant thermally induced stresses during both steady state and transient temperature conditions. Examples pertaining to temperature effects on refractory, copper cooling blocks, furnace shells, and complete systems will be discussed. The purpose of the paper is to highlight how stresses and strains are developed due to differential thermal expansion.

Jan 1, 2015

By Miro Mihelich

The mines and prospects in the vicinity of Landlocked Bay, 25 miles southwest of Valdez, Alaska (fig. 1), were examined, mapped, and sampled in July and August 1955 as part of a comprehensive investigation by the Bureau of Mines of ore deposits adjacent to Prince William Sound. The purpose of the investigation is to establish and record the location, nature, extent, and metallurgical characteristics of copper and associated metallization in the Prince William Sound district and to indicate, if possible, those areas in which additional exploration and development may be justified. Of particular interest are the possibly numerous deposits of massive iron sulfides that were neglected during early mining operations. These deposits may constitute important reserves of sulfur and iron. At Landlocked Bay deposits of copper-bearing iron sulfide minerals have been mined or partly explored through mine workings, which are in a zone about 1 mile wide along the western side of a large overthrust fault known as the Landlock Overthrust. Eight of the principal mines along this zone were examined end sampled. Although only three of the mines have a recorded production of shipping-grade copper ore, all have deposits of copper-bearing iron sulfide minerals that are similar in occurrence. The deposits occur as lenticular masses and disseminations of chalcopyrite, pyrite, and pyrrhotite which replace crushed rock or fill cavities along shear zones in greenstones and in sedimentary rocks that are exposed between sea level and an altitude of 2,500 feet. These lenticular masses of sulfide minerals range in size from small pods to ore bodies that have been stoped to maximum widths of 9 feet, strike lengths up to 70 feet, and dip lengths as much as 350 feet. Where accessible for sampling,, the copper content of the deposits ranged from a few hundredths of a percent to over S percent; zinc, gold, and silver are present in negligible amounts. Flotation tests of a sample composited to represent typical mine-run ore indicate that 81 percent of the copper is recoverable in a product assaying 28 percent copper at a concentration ratio of 17.5 : 1. INTRODUCTION Statistical records indicate that approximately 110,000 tons of metallic copper (about 16 percent of total Alaskan production) was produced from mines adjacent to Prince William Sound during the 40-year period ended in 1938. Although the principal production was from a large-scale mining and milling operation on Latouche Island (Kennecott Copper Corp., Beatson mine), a substantial amount of the total copper was derived from direct-shipping ores selectively mined or hand-sorted from numerous other deposits in the district. No production has been made since 1938; many of the claims have long been abandoned, and mine workings are either caved or deteriorating rapidly.

Jan 1, 1957

By G Fergus, M Hart, S W. Weeks

Rio Tinto Alcan has undertaken feasibility level assessments into the expansion of its bauxite mining operation in an area south of the Embley River in far north Queensland. The project has the potential to extend their Weipa operations by approximately 40 years.The construction and operation of two additional mineral ore processing plants are proposed for the South of Embley project. Golder Associates was engaged to develop and conduct modelling assessments of potential sources of water supply required by mineral ore processing.Two models were developed using GoldSim: a dam yield model and a water balance model. GoldSim is a graphical object-oriented modelling environment with a capacity to carry out dynamic probabilistic simulations. Originally developed by Golder, GoldSim has been applied successfully in a decision support role to a range of mine water management operations.The dam yield model was used to provide estimates of reliability and volume of annual water supply of several potential surface water dams. This information was then used to determine a hierarchy of water supply options for processing plant operations. The water balance model dynamically simulated the water demands of the two production plants and the consequential response in water supply, with respect to the timing and discharges provided by the various source options.Use of the model provided a preliminary operational tool to assist with water supply management decisions. Water quality issues required a blending of water from separate sources and attention paid to scheduling to ensure water supply through the dry season. The model also helped identify risks to water supply in the event of underperformance of one or more water supply sources. This allowed the operational rules to be refined to minimise those risks.The dynamic and stochastic modelling approach provided a method for identification of water supply issues susceptible to seasonal climate variability.CITATION:Weeks, S W, Hart, M and Fergus, G, 2013. A dynamic evaluation of water supply security susceptible to climate seasonality, in Proceedings Water in Mining 2013, pp 197-208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Russel Delmar, Rick Everdell, Harry Charalambu, John Tait

Award of the Design/Build Agreement for construction of Ontario Power Generation’s (OPG’s) Niagara Tunnel Project was made after an intensive 8-month international procurement process. The 14.4-m diameter × 10.4-km long rock tunnel will divert 500 m3/s of water from the Niagara River to the Sir Adam Beck hydroelectric generating complex. The procurement process and Design/Build Agreement included features to address the owner’s requirements regarding risk allocation and cost and schedule certainty, while encouraging innovative ideas from the industry, both technically and commercially. The process included an international expression of interest and prequalification, followed by an invitation for design/build proposals to qualified proponents, and comprehensive proposal evaluations and negotiations with several respondent proponents. An honorarium was provided to the unsuccessful participants in the proposal stage. The resultant negotiated Design/Build Agreement includes Owner’s Mandatory Requirements, negotiated contract terms and conditions, performanceincentive bonuses and liquidated damages for schedule and water delivery performance, a multistaged Geotechnical Baseline Report, joint risk management, references to preexisting community impact agreements and measures to reduce impact on tourism. It also addresses regulatory approvals and permits, an owner controlled insurance policy that required reference to the International Tunneling Insurance Group (ITIG) Code of Practice for Risk Management as a condition of coverage, site specific safety, security and environmental plans, formal team building, a dispute review board, and escrow documentation.

Jan 1, 2007

By Paul C. Lingo

The title of my talk today might lead you to two logical conclusions: The industry is faced with a problem that requires a solution and after discussing the problem I will offer a solution. The first conclusion is painfully accurate. One need only look at the accident statistics to be aware of the problem. During the eight-year period 1954 through 1962, the United States Bureau of Mines reports that falls of rock and coal accounted for 1,435 of the 2,516 fatal injuries that occurred in underground bituminous coal mines. Some improvement was made during 1962. For the first time since records have been kept, falls of rock and coal accounted for less than 50 per cent of the underground fatal injuries. The 105 deaths recorded in 1962 indicate that a great amount of work remains to be done in this area. As to the second conclusion, let me assure you at the outset that I have no panacean solution; however, I do propose to discuss some aspects of the problem and some possible methods of solution. What methods of solution are now, or have been employed in attempting to solve the problem? More specifically, what methods have you and your associates used? Has it been an orderly well thought out approach to the entire problem, or has it been a somewhat piecemeal approach which tackled the immediate problem and left the total problem for another day? Perhaps a new approach may be in order.

Jan 1, 1964