Search Documents

By John L. White

Vibratory driver/extractors do more than drive and extract sheet piles. I would say more than sixty percent (60%) of the time, vibratory pile driver/extractors are engaged in work that has nothing to do with sheet piles. This is the main reason I refer to this tool as a "driver/extractor", and omit the word "pile". I have spent the last twenty years applying the technology of the vibratory driver/ extractor to all areas of foundation construction. As you will see, the only limits are humankind's ingenuity.

Jan 1, 1997

By Professor of Civil and Environmental Engineering Northwestern University, Mike Wladron, Gordon Revey

A unique judicial opportunity allowed measurement of the response of three cracks in residential structure to blasting for underground aggregate mining. Instrumented cracks were located in the interior basement CMU mortar and upstairs dry wall as well as exterior brickwork. The dynamic environment was unusual. Even though the blasting occurred some 490 m (1600 ft) away, excitation frequencies were unusually high and there were no apparent surface waves. In addition there was no air overpressure wave to produce secondary crack response. As is typical, long term environmental effects produced greater crack response than did the blast induced ground motions.

Jan 1, 2007

By Ian D. Pirie

Presentation outline ?Project location ?Geology ?Resources and reserves ?Results of the FEED study ?Social and environmental considerations ?Project path forward

May 1, 2010

1. Paper1?Identification and enumeration of asbestos fibers in the mining environment: mission and modification to the federal asbestos standard Arthur M. Langer Asbestos-related disease is increased with cumulative exposure (the concentration of asbestos in the air and duration of exposure). The maximum duration is assumed to be a working lifetime so federal agencies control cumulative exposure by limiting the airborne concentration of asbestos fibers equal to or greater than 5 lm in length. Air samples are collected in the environment of interest by entraining the airborne particulates including fibers on membrane filters and then counting the number of fibers using phase-contrast light microscopy. In addition to length, the fibers must have a length to width ratio of at least 3 to 1. This ratio is also referred to as the aspect ratio. Some counting strategies placed an upper limit on the fiber width restricting the counting to respirable fibers. Airborne asbestos is controlled by monitoring a sub-population of the airborne asbestos. No asbestos fibers shorter than 5 lm or fibers of any length having widths less than the resolution of the light optical method are counted. In the non-occupational environment, the Environmental Protection Agency requires the use of analytical transmission electron microscopy and fibers and counting fibers with lengths of 0.5 lm or greater and aspect ratios of 5 to 1 or greater are counted. The permissible exposure limit for asbestos has been reduced by more than 120-fold since 1969, when the standard was 12 fiber/ml and the current monitoring methodology was developed. The manufacturing and mining worksites are regulated by two different federal agencies and the asbestos exposure limit was higher in the mining environment until recently (Mine Safety and Health Administration 30 CFR Part 56, 57, and 7, Federal Registry, February 29, 2008). Currently the permissible exposure limit (PEL) is the same in both types of workplace and it is 0.1 fibers per milliliter (fiber/ml) over an 8-h shift as a time-weighted average (TWA). A milliliter (ml) is equivalent to a cubic centimeter (cc) and sometimes this standard is reported as 0.1 f/cc. As the phase-contrast methodology was used to monitor lower exposures and environments, other fibrous mineral particulates were incorrectly characterized as asbestos. These occurred in talc deposits and taconite ores from the Eastern Mesabi Range.

Jan 1, 2008

By Mark Cross, Andrew P. Campbell, Koulis A. Pericleous

"Computational Fluid Dynamics (CFD) modelling is being used to simulate the freeze layers formed within direct smelting processes. There has been some concern whether water-cooled elements can withstand the p~ocess conditions and in particular abnormal cases where they may be splashed in molten metal.To validate the models being developed, two cases from literature have been modelled for solidification and stress analysis. The solidification case is presented in detail and is for hot molten metal flowing through a cylindrical pipe. The walls are at a temperature below the melting point for the metal. The resulting solid (or freeze) layer is within 3% of the value calculated by Sampson & Gibson9 •Preliminary modelling of the refractory-slag interactions is presented. Although three basic mechanisms: Penetration; Corrosion; and Erosion will eventually be modelled, only the penetration is considered here. The corrosion mechanism is to be modelled by tracking the time that the penetrated refractory is at the required temperature.Future work, after adding all the required physics, will focus on the modelling of a water-cooled element placed lower in the smelter. Process perturbations will be simulated to examine what these elements will withstand."

Jan 1, 2001

By B. S. Fee, R. R. Klimpel

"Froth flotation is the most widely used and economic means of concentrating metal sulfide ores such as those containing copper, lead, zinc, nickel, molybdenum, and pyrite. Also recoverable are other metal species that are often associated with sulfide ores such as cobalt, platinum, gold, silver, etc. Most of the initial developments made with the process of froth flotation in the early 20th century were based on the processing of metal sulfide ores. It is the relative technical and economic ease of floating metal sulfide minerals with small amounts of appropriate frothers and sulfur containing (thio) collectors that has been a major economic driving force behind the rapid expansion in the supply of metals such as copper, lead, zinc, and nickel that has occurred in the world's economy in the last 50 years. This author estimates that 1.6 billion tons of sulfide ores are processed each year (1980) in the free world based on the froth flotation process.While there has been a tendency for the quality of metal sulfide ores in any one geographic location to deteriorate over time due to mining intensity, the overall global supply of sulfide minerals is still very large. Thus, the physical supply side of sulfide ore concentrates has not been under strong technology improvement pressure with increasing metal demands. Part of this is due to the ability of capital to consistently move to new geographic locations having suitable grade sulfide ores. In these moves, the actual froth flotation technology used (including collector chemicals) has had to change little. As an illustration of this trend, of the approximately 80,000 metric tons of thio collectors used commercially (1980) in the free world, almost 98% were known and manufactured in some form 25 years ago (1). This is clearly not typical of reagent development in other process related industries. In addition, the industrial scale practice of froth flotation applied to sulfide ores has proceeded since the 1920 s with often little direct (predictive) scientific explanation due to the extreme complexity of the flotation process. Empirical testing has been a mainstay of industrial flotation reagent development and use. Even today there is often strong disagreement between researchers as to the mechanisms of chemical flotation practices that have been performed successfully at an industrial scale for many years."

Jan 1, 1987

By K. C. McMahon

This report is the result of the engineering efforts performed by the Mining Equipment Operations of FMC to develop methods of automating a continuous miner. This work was done as part of modification number three of the contract for the development of a miner/bolter system. As the demand for energy places an ever-increasing pressure on the coal mining industry to produce more coal, methods for underground mining which will increase productivity with a con-current increase in safety are being actively sought. Removing the machine operator from his station on the continuous miner and placing him at a safer location behind the machine while retaining his control functions via an umbilical cable or a radio link was an important first step. However, the problems of poor visibility, no control "feel", and the judgmental problems of controlling the sump distance and the shear limits have not been conducive to the productivity increase that is desired.

Jan 1, 1975

By Steven C. Borell

For more than a decade, changes have occurred each year that have improved the regulatory and business climate for mining in Alaska. These changes have taken place during Republican and Democratic governorships as well as when the state House of Representatives and Senate were controlled by either party. During some years, the changes have been relatively minor. In others, including the 2003 legislative session, the changes could only be characterized as massive. These improvements have encouraged exploration. This, in turn, has resulted in some major new discoveries. But Alaska is essentially unexplored and tremendous opportunities remain.

Jan 1, 2004

The Macraes Mining Company Limited was listed on the New Zealand and Australian stock exchanges in January 1990, and the proceeds of the float were used to purchase a 70 per cent interest in the Macraes Gold Project, previously owned by BHP Gold Mines (NZ) Limited. Macraes Mining has had a 30 per cent interest in the project since May 1984, when it was incorporated. Project financing in the way of a gold loan was secured in February 1990 and construction commenced shortly afterwards. The mine construction activities were completed within nine months and the mine commenced operations in October 1990.

Jan 1, 1991

This paper addresses the methodology of introducing risk into the development of mine plans for open pit mines. Recommendations are put forward for achieving a risk balance between mineral resource estimates and slope design. A design process identifying criteria for different stages of planning is presented. Business risk is separated from geological/geotechnical risk and procedures to address these within the development of mine plans are suggested. It is concluded that a formal design process improves communication between key decision makers and adds value to shareholders, investment.

Jan 1, 1997

By D R. Cohen

As one of the four basic sciences, the study of geology is intrinsically worthy as a means of increasing fundamental knowledge of the behaviour and evolution of the universe. Geological knowledge can also be translated into practical outcomes for society such as resource discovery and protection of the environment. Australia has a long tradition of providing very high quality geoscience programs to prepare graduates for a range of occupations. We are, however, reaching a nexus in the way universities should or can deliver engaging programs. This has been triggered by the rapid evolution of the digital world (the Internet of Things), new technologies, unprecedented access to information, better understanding of the processes by which we learn and adapt our thinking, growing complexity in the problems we must face or opportunities to grasp, and university funding models. Designing education programs for the next generation of geologists extends far beyond tinkering with syllabuses. We must develop skills sets that will allow graduates to work in rapidly changing landscapes, but in doing so may have to sacrifice content to build capability in our graduates. Whereas universities must respond to changing demands on graduates by ensuring degree programs contain an appropriate balance of material and high quality of delivery, industry and government must also fulfil their responsibilities to provide additional training programs for graduates to assist their rapid transition into independent professionals. This paper examines various educational issues being considered in developing the new Decadal Plan for the Earth Sciences, and reflects on directions that education is heading in many of our universities.CITATION:Cohen, D R, 2017. Educating the next generation of geologists, in Proceedings Tenth International Mining Geology Conference 2017, pp 3–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Kazem Oraee

Falls of ground have historically been the main cause for fatalities in underground mines. Although recent advances in technology have reduced the number of such accidents, when failures occur they usually result in severe consequences. Risks of rock falls, use of heavy machinery and electrical apparatus, entry to confined spaces, working in noisy and dusty environments, and working on unstable platforms are some of the hazards in ground control operations. Managing these risks requires a management regime involving strict adherence to operational codes of practice and an enshrined culture of safety. These should be subsequently reinforced through active participation of management, systematic training, and stringent internal and third party auditing. Accident reports show that the major contributing factor in most rock fall accidents is the failure to adequately manage known risks due to the lack of a systematic process. OHSAS 18001 (Occupational Health and Safety Assessment Series) is an international occupational health and safety management standard specification to develop occupational health and safety at the workplace. This standard is intended to help mine operators control occupational health and safety risks. Addressing the requirements of OHSAS 18001 can be a complex and demanding task. A comprehensive guide for efficient and accurate implementation of this standard is provided in this paper. The discipline can be used to establish an accountable management system foreground control activities in underground coal mines. The paper also provides guidelines for preparing necessary documents, devising safety policies, procedures, performing risk assessment, and handling instructions. Finally, the paper concludes by providing a sound analytical basis in terms of the creation of a robust safety management system foreground control operations in underground mines. Full benefits of implementing an effective and systematic operational health and safety management system are illustrated. The procedure adopted and prescribed in this paper can be used in all underground coal mines where lack of appropriate ground control practices can create deficiencies in both safety and productivity.

Jan 1, 2012

By C. Mosoane

ERPM was formed in 1893 and as a result of its age, a large volume of data exists in a paper-based format and it was decided to electronically capture data in one of two critical mining areas?namely at Far East Vertical (FEV) Shaft Area (Lower Areas) and Hercules Shaft Area (Upper Areas). The life of mine is dependent on tonnage and grade from these areas. Geostatistical evaluation of the gold reserves has been applied on an ad hoc basis in the Hercules Shaft Area and on a continuous basis in the FEV area. This is the first evaluation using geostatistics that was performed on the Upper Areas. This paper is based on the premise that regardless of cut-off grades, geostatistical estimation (kriging) estimates and locates reserves better than ?traditional? methods e.g. polygonal method, inverse squared distance method and it endeavours to estimate and locate the high grade reserves in the Main Reef Leader of Upper Areas.

Jan 1, 2003

By M Pyle, R Ch, T Vizcarra, ramohan, G Lane, G Ballantyne

Preconcentration, through gravity separation (Wallace et al, 2015), magnetic separation and particle size (Clout, 2013), has been used in many historical projects to convert low grade material into ore. More recently, pre-concentration technologies such as bulk sorting (Kurth, 2017), screening (Bearman, 2014) and coarse particle flotation (Vollert et al, 2019) have also demonstrated their ability to progressively reject waste through the value chain. These technologies can not only deliver stepchange improvements to the economics of mining operations, but can transform the environmental and social aspects by minimising water and energy consumption and significantly reduce the quantity of fine tailings produced. However, implementing progressive waste rejection requires technologies and approaches to be combined and applied in the right way to capture the value. From a technical perspective, progressive waste rejection introduces challenges related to the orebody, equipment performance, engineering and understanding the value chain from the resource through to final product. From a management perspective, the key issues are related to people and processes, in particular; motivating the business, challenging the paradigms, and introducing new ways of operating within the constraint of existing management structures to manage risks and minimise lost opportunity costs. This combination of technical and management issues means that progressive waste rejection is a complex undertaking for mining companies, yet the reward for the business and other stakeholders is potentially high and should not be ignored. This paper presents how progressive waste rejection can offer step-change improvements to the business case for high and low grade greenfield and brownfield projects based on case studies completed by Ausenco. The paper then outlines different implementation approaches from concept studies to execution to address the various technical and management challenges outlined above.

Nov 10, 2020

By using knowledge-based technology to create a Virtual Mining Enterprise and integrating it with existing technical and financial computer systems, a gold mining company has been able to reduce the time taken to produce a mine plan from 14 weeks to less than one week. Typically, the mine planning process requires circulating and managing large amounts of information. Even with the use of computers in todayÆs business, this is often still a manual process involving file transfers and individualised spreadsheets. Mine planning also involves understanding and managing large quantities of complex and interrelated variables. Added to this is the ever changing dynamics and constraints associated with the business of mining. These issues not only hamper the planning process but also question the validity and usefulness of the mine plans being generated. By integrating the information and knowledge of the numerous departments involved in mine planning into one core Knowledge Base - so called æone version of the truthÆ, - mining companies are able to overcome these pitfalls experienced in traditional planning methods. Once set up, the Knowledge Base creates and runs a virtual mining enterprise with which to visualise and test various scenarios of mining, business and logistical activities. The final output is an optimised enterprise-wide plan with clear and detailed instructions for each of the divisions of the company.

Jan 1, 2000

By Wood W, Bell A

Brown coal production in Victoria's Latrobe Valley Region (Figure 1) continues to rise and currently stands at around 50 Mt per annum. With the exception of around 2 Mt used to produce some 700 Kt of brown coal briquettes, this coal is mined by the State Electricity Commission to fuel large thermal power stations with a total installed capacity of just over 5 000 Megawatts. The moisture content of the coal as mined typically exceeds 60 per cent, making Latrobe Valley coal a markedly low rank fuel. The lack of heating value is, however, compensated for through power station design and by the fact that ash yield is very low, usually within the range of one per cent to four per cent on a dry basis. This means that compared with most other coals, the burning of Latrobe Valley brown coal produces relatively small quantities of waste products and discharges a minimal level of pollutants into the atmosphere. Even so, the inherent quality of Latrobe Valley coal does vary significantly from one area to another (Gloe, 1991; Barton et al, 1992) both on a local and a regional scale. Such variations need to be recognised and understood in order to not only realise efficiency gains in existing power stations but to properly assess resource potential for future utilisation and the application of new technologies. The principal aim of this paper is not to describe coal quality variation in detail or to speculate on the nature of and reasons for such variation. Rather, it is to simply underscore that significant differences do occur and that this is clearly a factor which needs to be considered in any evaluation of Latrobe Valley brown coal as a resource for the future.

Jan 1, 1992

By H. Appiah

Small scale mining (SSM) has been going on for a long time in Ghana. SSM was legalized by the PNDC Law 218, 1989. Since then there have been numerous gains from the SSM industry. The SSM is organized locally by the concession owner who engages people to work for the gold which he buys. Small scale miners (SSMs) use crudely made sluices in Ghana and, therefore, their production falls below what is expected. The SSMs work in groups and not as cooperatives, as they do in Brazil and other Latin American countries. Legalization of SSM has curbed gold smuggling considerably because a gold marketing entity is available. SSM poses certain environmental problems like pollution of water bodies and soils by mercury and indiscriminate digging of pits.

Jan 1, 1998

By Qingqing Huang, Mohammad Rezaee

The Mineral & Metallurgical Processing Division (MPD) of the Society for Mining, Metallurgy & Exploration held the 12th MPD Student Poster Contest on March 2, 2022, during the MINEXCHANGE 2022 SME Annual Conference & Expo. The event showcased the work of 32 graduate and undergraduate students from U.S. and international institutions. The contest began in January when the students submitted one‐page abstracts for judging. In February, they prepared and presented posters that explained their research, and each student had five minutes to explain their research to a panel of judges during the conference. Recognizing the students’ efforts in working hard on their research topics and setting aside time to complete the necessary steps to enter the poster contest, the MPD provides monetary rewards to all participants. For graduate students, first place receives $1,000, second place $500, and third through seventh places $200 each, and for undergraduate students, first place receives $1,000 and second place $500. The main authors of nonplacing entries receive $125 each. Participation in the contest includes a free ticket to the MPD Luncheon, where the winners are announced.

Nov 22, 2022

By L. Holappa

Ferroalloys like FeCr and FeMn are mostly produced in submerged electric arc furnaces. Typical of these processes is that the amount of slag is quite high. The role of slag for the process is thus essential and specific chemical, physical and electrical properties are required. Slags in FeCr process are Al2O3-MgO-SiO2 based with minor contents of CaO and CrOx. Slags in the FeMn process are principally similar, originating from silicate minerals but can have quite large composition range depending on the manganese ore and its gangue minerals. Characteristic of the FeMn process is that the slag is rich in manganese oxide up to above 30%. A common feature is that the ?ore oxides?, CrOx and MnOx in slag are not only divalent oxides but also contain some higher valent of Cr3+and Mn3+, respectively. In FeMn production conditions the slag consists mainly of Mn2+. This is a clear difference from CrOx containing slags in which both two and three valent coexist in slags in FeCr process conditions. Oxidation state of the slag depends on the ambient oxygen partial pressure and temperature in the examined process. The thermodynamics of slags in ferroalloys, production are discussed in terms of phase diagrams, activities and oxidation state of chromium and manganese oxides. Further, slag properties influencing reduction kinetics and furnace operation i.e. viscosity and electrical resistivity are discussed. Keywords: review, slags, ferroalloys, ferrochromium, ferromanganese, thermodynamics, physical properties

Jan 1, 2004

By Joram M. Amir, Ernst Niederleithinger, Nikolaus Schneider

"Abstract: Diaphragm walls are used to provide a stable and watertight confinement for the construction of tunnels, underground railway stations, deep basements and other structures requiring deep excavations. Water seepage and soil loss through the joints have occurred on several occasions, causing extensive damage. This may have been due to uncontrolled concrete flow between the joints, unexpected geologic conditions or just poor workmanship.Different ways of quality assurance are applied on construction sites. Most of them rely on recording parameters of the construction equipment and conventional concrete quality control. In the frame of the EUREKA/ZIM project DiWaQ we have looked at several ways to perform non-destructive quality control. Some methods are to be applied after excavation before concreting (phase 1); others after the wall is completed (phase 2).For phase 1 we have used two different principles for checking the shape of the excavation, especially the joint to existing panels. A mechanical device which can be adapted to the excavating equipment was developed; field tested and validated on test and construction sites. It is described in detail in another paper in the same volume. A sonar-based device with a 10 mm resolution has shown good performance in the lab, but is still under development.For phase 2 different temperature sensors have been lowered into access holes to monitor the hydration heat developed during concrete curing. The same tubes can also be used to perform electromagnetic and ultrasonic crosshole measurements across or along joints to detect flaws. Especially the ultrasonic method has shown promising results on validation specimen at the BAM test site at Horstwalde, but limitations as well. Success substantially depended on the joint type, flaw size and distance of the sensors to the joint."

Jan 1, 2014