Search Documents

In late 1989, first-pass reconnaissance exploration delineated a 4km x 6km geochem- ically anomalous area centred 10km WNW of Kainantu in the Eastern Highlands Province at 6¦13'S and 145047'E. The area, named the Basangka prospect, lies between 2 200 and 2 400m asl. Interest in the area was prompted by a 14ppm Au assay of a silica-pyrite breccia float sample taken near Henkai village. The prospect was defined after several acid-leached silica- pyrite breccia and comb textured quartz float samples returned assays above lppm Au and relatively high Ag. Very encouraging and anomalous Au values were obtained from panned concentrates, despite the absence of visible Au colours. Several pan concentrates returned greater than 1mg Au and it is believed that the Au occurs as inclusions within iron oxides which were originally pyrite. In this early stage of prospect exploration, any Au value above 0.lppm in- 150# fraction stream sediments is treated as anomalous. Rock chips, panned concentrates and -150# fraction geochemistry all vividly define the areas of interest at Basangka.

Jan 1, 1991

By Constantine C. Popoff

This report reviews and analyzes, by a simple analytical and logical reasoning, the conventional methods of reserve computations of mineral deposits described in various domestic and foreign publications. It brings together, formulates, and evaluates the principles underlying interpretation of exploration data; and ties such principles to the proposed classification of methods. The material is discussed in sufficient detail to allow general application.

Jan 1, 1966

The purpose of this study was to investigate the immobilization as a host for metallic pollutants (Cr, Cu, Pb, and Zn) by ettringite phase. Ettringite phase is produced through hydration reaction of calcium aluminate with gypsum. From the XRD patterns, it is known that the distance between spaces in 010 planes in ettringite crystal increase with an increase of ionic radius of heavy metal except Pb; no big difference is shown. For this reason, the d-value of 010 planes in ettringite crystal increased with the substitution of Cr, Cu and Zn having a big Al ironic radius. But in case of Pb, because the substitution occurred at calcium site, it does not influence to increase d-value of 010 planes.

Jan 1, 2006

Discussion continuing that published in Trans.I.MIn.E ., 1915, vol.L, p.449 and 1916, vol.LI, p.166, included contributions by Smith W., McLaren R., Gibson J., McCreath W., Sneddon J.B., Kirkpatrick J. and Mowat D.M. and a written response by Black J.N.

Dec 1, 1916

In recent years it has been more and more recognised that applied geology can be of service to the mining industry, and many mining companies overseas now have permanent geological staff as part of the operating organisation.Most of these companies insist that the geological department must pay for itself by the savings it can make in operating cost, and the growing use of the geologist is proof that such savings are made.The geological problems in every district are different, and a description of the problems and method of attack in a specified district is a useful addition to the literature of mining geology. Very few contributions, from the standpoint of the mining company geologist, have appeared in the Australian literature so that, although the operations of Bendigo Mines Limited are still in the development stage, and its geological work newly established, a description of the routine geological work at Bendigo should beof interest.Although most Bendigo mining companies have not employed permanent geologists, they have utilised geological guidance wherever possible, and a great body of data has grown up. Acknowledgment is made here to the valuable work of the Geological Survey of Victoria, especially the writings of E. J. Dunn, H. Herman, and H. S. Whitelaw, and the maps of Caleb Thomas and H. S. Whitelaw; and also to the work of independent investigators, notably Chief Geologist, Bendigo Mines Ltd.

Jan 1, 1936

The Harmonious Design on the Beneficiability for the Pt-Pd Ores Containing High MgO Gangue in Yunnan

Sep 13, 2010

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The ?slope stability radar? (SSR) has been developed to better manage those risks. The SSR remotely scans rock slopes to continuously measure any surface movement and can be used to detect and alert users of wall movements with sub-millimeter precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many metalliferous and coal mines throughout the world. Over 80 systems are currently being used with current operations in 17 countries. Greater than 200 rock slope collapses and waste dump failures (from several to millions of tones) have been monitored, with ?warning? precursor movements recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper will present recent case studies of the SSR operation in coal and metalliferous mines. Slope Stability Hazards and Rock Slope Monitoring in Open Pit Mines Surface mining often creates excavation boundaries which are steeper than those would be created under natural processes in the same rock type. They are also undertake quite rapid stress changes during mining and are influenced by significant external forces such as blast vibrations and changes in groundwater. These conditions are likely to allow some degree of instability to develop in the pit slopes. The hazards associated with this instability of pit slopes can be extremely variable in character; ranging from small cobble sized rocks dislodging and falling from mine benches to complete collapse of entire pit walls. It is usually the position of mine geotechnical or geological staff to assess these hazards for mine operations. The assessment of hazards due to unstable slopes can be done by visual observation of precursor signs such as fracturing or rilling of loose material. A more reliable indicator of instability involves the quantitative measurement of outward movement and acceleration of material as an instability mechanism develops. There is strong evidence that small precursor movements of a rock wall occur for an extended period prior to rock slope collapse (Hoek and Bray, 1981). Development of a monitoring system, adopting acceptable slope deformation criteria coupled with warning systems and design of stabilization or risk reduction measures if appropriate has become a standard method of dealing with slope instability. Framework for Slope Hazard Management using the SSR A framework for the management of slope hazards is shown in Figure 1 (discussed in detail in Harries, 2007). Although this framework is specifically for use with the Slope Stability Radar, a similar framework could be developed for other monitoring technologies for monitoring slope deformation. An important point to consider is the sequential nature of the hazard management framework from selecting the context ? identifying hazards ? analysing hazards ? evaluating hazards ? treating hazards. [ ] Once the context of the system has been developed (for example ? to monitor for rapid bench scale collapse), the identification of hazards is the next stage in hazard management. Identification of slope hazards can be relatively straightforward due to the visual nature of the information that the SSR system produces. The areas of excessive wall deformation are highlighted in color maps of the mine slope with a co-aligned photographic image to review the actual site of interest. The responsible personnel must then analyses this data, usually reviewing the deformation style and rate, as well as the size of area that appears to be failing. This information can then be evaluated against organisation protocols (for example it may be only a small sub-bench failure that will be ?caught? by existing benches and hence can be categorized as a lower risk). Once these hazards are evaluated they can then be treated if required. Two major options are available to reduce the risk during this treatment option. We can reduce the likelihood of failure ? for example by buttressing the failure or de-pressurising of water pressures in a slope. However, the most likely plan of action is to reduce the consequence of the failure. One of the most successful opportunities to reduce the consequence of a slope failure is to ensure that no personnel or mining equipment is present at the location of a slope failure when collapse finally occurs. This has been the major benefit of the SSR system to the different mining operations around the world. SLOPE STABILITY RADAR TECHNOLOGY OUTLINE Slope Stability Radar system specifications and capabilities: ? Measurement precision +/- 0.1mm (std.) ? Perforated dish and other features enable it to operate in high wind conditions ? Measurement range is 1700 metres ? Scans 270 degrees horizontally and 120 degrees vertically ? 1 ? 30 minute repeat rate for area scans (varies according to area being scanned ? RF exposure (<0.05mW/cm2) is a factor of 200 below the acceptable limit for the general population (1 mW/cm2) ? Tolerant to vibration and mining equipment ? The system weighs approximately 1500 Kg ? Remote area power supply enabling unmanned, continuous 24/7 monitoring ? Real time monitoring

Jan 1, 2009

By Bernd Hagenah, Katie Theis, Cristina Lauzon, Petr Pospisil

Lidding over or tunneling existing transportation infrastructure is currently under review in several U.S. cities. The main reasons for this are the use of the created space for urban development, the reduction of noise and exhaust fumes for the residents, and, thus, a significant increase in the quality of life. The main aspects to be considered during the planning process are (1) total investment and operational costs, (2) impact of construction works on current traffic, (3) safety and fire protection, and (4) socio-environmental issues. The paper presents some basic planning principles, and experiences of recent urban highway coverages are shared.

Jun 23, 2024

Future climate variability and change will impact on mining operations and their attendant communities. To minimise this impact, early and informed risk management is warranted. However, research into the risks posed by climate to the Australian mining industry has so far been limited. We are conducting a systematic study of the mining life-cycle to identify the main areas of vulnerability and adaptive capacity of operations and communities. This project aims to assess what adaptation activities are currently being undertaken within the mining industry and its communities across Australia and to develop a risk management approach that will aid the adaptation of practices in and around the industry, better assuring the security of people, jobs, revenue and the environment under changed or extreme climate conditions. The Canadian mining industry was recently assessed through a similar study, which found that many mining companies perceive a real risk to mining from climate change in the future, despite few companies being actively involved in managing such risk. At a workshop held by CSIRO involving mining specialists, the most vulnerable stage in the mining process in the Australian context was assessed to be production. In particular, impacts on water and energy supplies and also transport and infrastructure were of high concern. Additionally, heat stress on workers and equipment, changes in groundwater flow and increases in geohazards were also identified as important factors in the short and long term if problematic climate events become more extreme or more frequent. Risks in the planning and post-mine stages were also identified. Based on literature reviews and preliminary discussions with mining experts, here we present an initial assessment of the climate adaptation issues relating to mining and its associated communities and describe our future work plans in this area.

Jun 1, 2010

By Hyung Jeek Kim, Jongmin Joo, Jonguk Kim, Jai-Woon Moon, Kyeong-Yong Lee

"Co-rich ferromanganese crusts (Fe-Mn crusts) distributed on seamounts in the western Pacific are potential economic resources for cobalt, nickel, platinum, and other rare metals in the future. Evaluation and selection of a mining site can be established based on abundance and grade of Fe-Mn crusts in the site as well as topography that should be smooth enough for mining operations. Therefore, acquisition of shipboard echo-sounding and acoustic backscatter data are prerequisite to the selection of potential mine sites in addition to visual and sampling operations. Acoustic backscatter data can be used to locate crust-covered areas on a regional scale with the understanding of acoustic properties of crust through its correlation with visual and sampling data.During an expedition that took place from January to March 2014, KIOST collected geophysical and geologic data to assess the resource potential for Fe-Mn crusts on three seamounts (guyots) in the Western Pacific. In OSM11, one of the three surveyed seamounts, three camera tows were performed to observe the distribution of Fe-Mn crusts on the summit and slopes of the seamount. Although sediments of various thicknesses generally cover most of summit region of OSM11, several regions with high backscatter signals occur on the periphery of the summit. The occurrence of Fe-Mn crusts, observed during the camera tows, on those high backscattered regions suggests that the backscatter signals of shipboard multi-beam sonar can reflect changes in the geology of the seafloor from sediment layer to Fe-Mn crust deposits. The Fe-Mn crust deposited around the summit region is worthy of notice because of its topographic characteristics, including shallow depth, flat or gentle inclined surface, and smooth relief, which are more suitable for mining operation compared to the flanks of seamount."

Sep 1, 2014

By Paul Hosford, Tim Haldane

"The paper describes the fast-track development of the project from feasibility study through to detailed design and construction, highlighting the process adaptations for handling sticky ore and water management in a tropical environment, and subsequent commissioning and operating experience of the mine. The paper discusses the geological setting, the environmental and socioeconomic considerations in developing and operating a mining operation in an underdeveloped country and the logistical challenges involved in bringing a large capital investment into Central America.INTRODUCTIONGlamis Gold Ltd. acquired the San Martin project in Honduras as a result of its merger with Mar-West Resources in late 1998. Despite the prevailing low gold price environment at the time of acquisition, Glamis anticipated rapid development of the San Martin project due to the quality of the deposit and other positive factors.Following favorable exploration and permitting activities in the first half of 1999, Glamis prepared a Feasibility study. In October 1999, Glamis decided to proceed with the development of the project and selected Hatch to provide the engineering, procurement and construction management services for the project. The San Martin project was in full-scale commercial operation approximately 14 months after the receipt of Board approval, and by July 2001 the San Martin project was operating at approximately 150% of its feasibility design capacity."

Jan 1, 2002

By M. A. T. Cocquerel, M. G. Burcher, J. G. Eacott

"This paper is based on work carried out to examine the feasibility of increasing the smelting rate of two oil-fired calcine-charged reverberatory furnaces . Various constraints prevented physical enlargement of the furnaces and so allention turned to the use of preheated combustion air or oxygen enrichment to bring about the required increase in production. As a basis for further calculation, a furnace heat balance is determined using the smelting metallurgy and combustion data for the current operation. Various other operational data are tabulated and compared with similar data from other operating copper smelters.New heat balances are derived for various levels of combustion air preheat at the current smelting rate, and the effects of air preheat on oil consumption, combustion air and waste gas volumes are tabulated. These data are used to demonstrate the level of increased throughput which would be obtained before constraints in existing gas handling equipment are encountered.A similar exercise for oxygen enrichment is set out, with oil consumption, combustion air and waste gas volumes at various enrichment levels tabulated for the current smelting rate. These data are in turn used to demon strate the smelting rate which would be achieved at a practical level of enrichment before waste heat boiler and gas handling constraints are encountered.The energy implications for both cases are summarized."

Jan 1, 1980

By K. K. Kershner

Nickel having a purity of more than 99.99 percent with reference to metallic impurities was electrodeposited at the Rolla Metallurgy Research Center of the Federal Bureau of Mines. The production of high-purity nickel is in keeping with the current trend in technologies for producing metals with lower and lower percentages of impurities. To understand more fully the role to be played by nickel by itself and as a component in many alloys, the element must be in a state of high purity. Procedures are outlined for purifying nickel solutions by precipitating and filtering off impurities. Details are given for using the purified solutions as electrolytes in depositing high-purity nickel. The elecneleposited nickel contained 0.0005 to 0.002 percent each of cobalt, copper, aid iron together with spectrographically detectable traces of aluminum, magnesium, and silicon. The deposits were smooth and dense; the crystalline structure was typical of an electrodeposited metal. Some preliminary experiments for purifying nickel solutions by liquid-liquid extraction are also described in this report. Tests of this type were limited since more encouraging results were obtained by other methods of purification.

Jan 1, 1961

By J. D. Lowell, L. Quevedo

I will talk today about a porphyry copper exploration program now underway in the Amazon jungle in the southeastern part of Ecuador near the border with Peru. The project is unusual for two reasons: first the deposits are of Jurassic age, 153 m.y.o., which is unusually old for porphyry copper deposits and they may be the most significant pre-Tertiary age porphyry deposits known. Second, the district was found only six years ago which makes this the most recent discovery of a totally new porphyry copper district. The new porphyry district, known as the Zamora River Copper Belt, or the Corriente Copper Belt, is a north trending area 50 km long by 10-15 km wide, which is nearly aligned with the axis of the Jurassic age Zamora batholith and with the course of the Zamora river. Gencor in 1994 initiated a regional grassroots gold exploration program based on reconnaissance geologic mapping and geochem sampling which did not find a gold mine, but which identified the San Carlos porphyry copper system in April, 1995. In a later reorganization between Gencore and Billiton the Ecuador project was transferred to Billiton and between the Gencore work and Billiton’s a total of 10 porphyry copper systems were found over the next four years. In the period of 1997 - 1999 Billiton drilled a total of 11,000 meters of wide spaced core holes in the San Carlos, Panantza and Kutukus prospects. In October 1999 Billiton concluded a farm-out, joint venture agreement with Corriente Resources and Lowell Mineral Exploration for additional exploration of the Zamora property. This is funded by Corriente and managed by Lowell Mineral Exploration and a total of 28,000 m of core drilling was completed through August 2001. An immediate result of the Corriente Lowell project was the discovery of potentially commercial ore reserves in two new deposits at Mirador and Warintza. Additional closer spaced drilling was done in the Panantza deposit and additional drilling is planned at San Carlos, in targets related to Warintza, and elsewhere.

Jan 1, 2002

By J. Konnerup-Madsen, T. Unlu, H. Stendal

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The region includes the Deveci siderite/goethite deposit and the Hasancelebi, Karakuz and Kuluncak magnetite/goethite deposits; Deveci is the only mine in operation. The area consists of a serpentine-gabbro complex overlain by a volcano-sedimentary sequence hosting the iron ores. At least three generations of hydrothermal alteration have affected all rock types except the latest trachytic dykes. The Deveci deposits occur in a pyroclastic volcano-sedimentary sequence with shales and carbonates equivalent to the main mafic sequence, whereas the other three deposits formed contemporaneously with the intrusion of trachytic dykes. The deposits are of the volcanic-exhalative type, with syngenetic siderite in pillow lavas or stratiform layers the primary and main Fe-bearing mineral. In the west hydrothermal alteration has replaced siderite in pillow lavas with magnetite or has remobilised sideritic iron into magnetite veins

Apr 1, 1995

By Michael P. Sudbury

Non-ferrous slags are granulated and stockpiled as an alternative to pit cooling or transporting molten slag to a dump. The chemical composition of such slag is determined by the pyrometallurgical process in which it is produced, while the size distribution is set by safety concerns or a desire to reduce wear of pumps, pipelines and other equipment. Relatively few operations give consideration to the effect of granulation conditions on other properties of the granulate as the material is typically accumulated on the smelter site. It is becoming recognized that slag has many potential commercial uses and carries much of the energy applied to the smelting operation. This paper outlines the findings of extensive work to identify uses for granulated non-ferrous slag, the importance of preparation conditions on the properties, impediments to more extensive use of granulated slag, the real costs of slag stockpiling and the opportunities for further productive research.

Jan 1, 2006

By Raymond B. Ladoo

Toward the end of 1920 , the average grades of ground feldspar offered to the pottery industry were so poor and so generally unsatisfactory that many of the largest consumers decided to take active steps for their own protection . A few of the potters made arrangements to grind their own feldspar , while others asked the Bureau of Mines to make a detailed study of the problem and to suggest methods of improvement . Accordingly such a study was undertaken, the partial results of which are outlined in this preliminary report . The outstanding features of the present feldspar industry which are of interest in this connection are stated below. (1 ) Many grinding companies do not own or control all or even a major part of their sources of crude material , but buy in job lots from many sources . (2 ) There is great need of more adequate engineering and chemical control over mines and mills . ( 3) ~ Out of date , inefficient methods and equipment for mining and grinding are in common use . (4) Little or no cooperation exists between feldspar producers , but on the contrary many feldspar companies are exceedingly secretive . This tends towards (a) preservation of obsolete methods ; ( b ) want of knowledge of the essential features of production , market requirements , and the relation between total milling and consuming capacities of the country; ( c ) inefficient and often mistaken trade practices ; ( d) unprofitable and even ruinous competition in dull periods . (5) The small size of many feldspar deposits precludes maintenance of an efficient organization at each individual mine . ( 6 ) Many of the best deposits of feldspar situated close to railroads are becoming depleted , which results in gradual lowering of grades , and increase in cost for better grades . (7) There is a lack of exact mowledge of the ceramic properties and behaviour of feldspar by some consumers , which results in ( a) purchase of feldspar on the basis of price alone , thus encouraging low production costs at the expense of quality , and ( b) inefficient and expensive cross- hauling of both crude and ground feldspar .

Jan 1, 1922

Demonstration of Solid-Liquid Separations Using Recycled Supernatant that Contains Temperature-Responsive Polymer The effective use of recycled supernatant that contains temperature-responsive flocculant is demonstrated for solid-liquid separations. The recyclability of poly(N-isopropylacrylamide) (PNIPAM) of several different molecular weights and a 15 per cent negatively charged derivative are compared. Batch settling tests of a-alumina suspensions are first conducted at 50¦C, with a subsequent 25¦C period, after which the supernatant is harvested and used to flocculate subsequent suspensions. Using this procedure consecutive separations are obtained with the repeated recycling of uncharged PNIPAM containing supernatant. Batch settling tests indicate that hindered settling rates increase with molecular weight of PNIPAM. Adsorption studies indicate that strong adsorption of PNIPAM onto alumina occurs with PNIPAM at 50¦C and that significant desorption occurs after cooling at 25¦C. However, the extent of desorption decreases with molecular weight resulting in low amounts of PNIPAM for recycling and poor settling behaviour when high molecular weight PNIPAM is recycled. Little recyclability was evident using the negatively charged PNIPAM. On the basis of these findings a recycling-thickener apparatus that uses low molecular weight uncharged PNIPAM is proposed.

Sep 13, 2010

By D. Laguitton, D. Hodouin, V. K. Gupta, R. Spring

"The CANMET SPOC project aims at inducing progress in process evaluation and optimization by developing user oriented software based on state-of-the-art theory. The present work is the result of a joint effort by CANMET, Noranda Mines and Université Laval to develop two computer packages: one (RTD) to calculate the residence time distribution that best describes the material transport through the mill, the other (FINDBS) to estimate the rate of breakage and distribution function of the population balance model in a ball mill. The RTD package can handle data from various experimental methods (impulse or complex tracer feed, with or without recycling, etc...). The FINDBS package provides options for the functional description oj both model parameters Band S. The full detail of the methods and programs appears in a users guide. The program capabilities and several sample runs are presented.IntroductionSimulation of mineral dressing operations by computer has been largely contained within academic and research circles and has not yet gained a status of routine practice in the ore and coal industries. It is however a matter of time before process simulators are available on every process engineer&apos;s desk to assist process optimization tasks, flowsheet design and professional training. The CANMET SPOC project (Simulated Processing of Ore and Coal) was initiated in 1980 to assist the Canadian industry in integrating computer-based methodology for process evaluation and optimization(1). Software development, documentation and transfer is one of the main priorities of the project which will mature in 1985 by releasing a complete package of manuals and programs covering sampling, material balance computation, unit modelling, flowsheet simulation and optimization . This paper is a condensed description of a typical project element in its 1982-1983 state of development. The required methodology for ball-mill modelling and simulation was consolidated an d merged to other project elements during a joint study under contract financed by CANMET and Noranda Mines Ltd . The first part of the study dealt with documenting experimental methods and software for ball-mill computer simulation. Université Laval GRAAIM (Goupe de Recherche en Automatistion Appliquée à l&apos;Industrie Minérale) acted as sub-contractor for this part of the study(16,17). A second part dealt with applying the model calibration techniques to a large industrial data base and is reported elsewhere(2,18,19)."

Jan 1, 1984

By W. N. Marchant

[The citrate process for flue gas desulfurization (FGD) is a product of continuing research by the U.S. Bureau of Mines to meet the goal of minimizing the objectionable effects of minerals industry operations upon the environment. The reduction of SO2, in solution by H2S to produce elemental sulfur by the citrate process is extremely complex and results in solutions that contain at least nine different sulfur species. Process solution analysis is essential to a clear understanding of process chemistry and its safe, efficient operation. The various, chemical species, the approximate ranges of their concentrations in citrate process solutions, and the analytical methods evolved to determine them are hydrogen sulfide (~0M to 0.06M) by specific ion electrode, polysulfides (unknown) by ultraviolet (UV) spectrophotometry, elemental sulfur (~0M to -0.001M dissolved, ~0M to ~0.1M suspended) by W spectrophotometry, thiosulfatc (~0M to ~0.25M) by iodometry or high performance liquid chromatography (HPLC), polythionates (~0M to ~0.01M) by thin layer chrornatogrphy (TLC), dithionite (searched for but~ not detected in process solutions) by polarography or TLC, bisulfite (~0M to 0.2M) by iodometry, sulfate (~0M to 1M) by a Bureau-developed gravimetric procedure, citric acid (-GM to 0.5M) by titration or visible colorimetry, glycolic acid (~0M to 1N) by HPLC, sodium (~1.5M) by flame photo¬metry, and chloride by argentometric titration.]

Jan 1, 1980