Search Documents

The Pinto Valley, Arizona, plant of Cities Service Company is one of the newest copper producers in the United States, having started production in 1975. It is located a few miles west of Miami, Arizona, on the site of the Castle Dome Mine, a World War II operation which was shut down and its mill later moved and renamed the Copper Cities plant. The Pinto Valley concentrator uses six 18 ft (5. 5 m) diameter by 21 ft (6.4 m) long, 4000 hp, single-stage ball mills, taking crushed ore from four 7 ft (2. 13 m) standard and eight 7 ft shorthead crushers. It has a design capacity of 40,000 stpd but has higher tonnage capability for an expanded concentrator. The copper porphyry-ore is mined by two 15 yd and one 20 yd shovels (11.5 and 15.3 cu m) and is transported to the primary crusher by 150-ton trucks. The dump pocket is relatively shallow (14 ft or 4. 27 m deep); and because of the width necessary for the 150-ton trucks, it was designed to use the ore itself instead of manganese steel as an abrasion- resistant lining, although a heavy steel cap protects the dump pocket top edge. The pocket has a capacity of 300 tons of ore. Water sprays under the dumping positions direct a fog toward the truck being dumped for excellent dust control. Breaking of oversize is done by a hydraulic impact breaker mounted on a hydraulically operated articulated arm situated at the side of the dump pocket. Again because of the shallow pocket, no splitter is used to protect the spider of the 60 in. by 89 in. Traylor gyratory crusher, which is equipped with a hydroset mechanism. Crushed ore at 8 in. (203 mm) drops into the 360 st surge chamber lined with AR plate and then is fed directly to the 60 in. (1.52 m) stock- pile conveyor by an 84 in. by 20 ft (2. 13 m by 6.1 m) four-speed apron feeder at a rate of up to 4000 stph. Early in 1977, Cities Service will replace the four -speed electric drive with a hydraulic pump and motor with infinitely variable speed. They are also studying the replacement of the apron feeder with an 8 ft wide (2.44 m) belt feeder similar to those at Similkameen and Palabora. Peak crushing capacity would then be increased to 5000 stph. The AR plate in the crushed ore pocket was installed in large, rectangular sheets which required much less embedded metal to hold it in place than would the more conventional, smaller arid square pieces of cast manganese steel. For duty in the crushed ore pocket, where wear is not severe, the AR plate is a satisfactory material. The new Palabora Figure-8 crusher also uses this design.

Jan 1, 1978

By R. A. Reiley

Introduction Democratic countries are founded on the principle that all citizens have the right to participate in policy setting and decision-making processes. Citizen participation is especially evident in environmental issues and policies. In the United States, there are currently over 10,000 environmental organizations and new ones are being formed each year. Many of these organizations are formed on a watershed basis and are particularly concerned about the impact mining has on the environment. While the environmental issues vary from area to area, most concerns center around mining impacts related to subsidence, water pollution, and water diversion. Citizens have a number of avenues for participating in lawmaking that affects the mining industry. Some of these avenues include participation in litigation and citizen ballot initiatives. In addition, there are less formal methods of participation that include attending public meetings, commenting on agency rules or lobbying on specific legislation. The intent of this article is outline the various public participations mechanisms, highlight the latest legal developments that have affected mining industry through citizen participation, and briefly discuss emerging issues.

Jan 1, 2001

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

This study investigated the performance of citric acid as lixiviant for cathode material from end-of-life lithium-ion batteries (LIBs). Black mass containing 84.2 weight percent MNC (LiNi0.45Mn0.4Co0.15O2) and 15.8 weight percent LCO (LiCoO2) material was leached at solid-to-liquid ratios of 20, 50 and 100 g/L. Leaching with 1.5 M citric acid, 2 volume percent H2O2 and a solid-to-liquid ratio of 20 g/L at 95 °C extracted 90 percent Co, 95 percent Li, 94 percent Mn and 94 percent Ni within 20 min. At the highest solid-to-liquid ratio of 100 g/L with 1.5 M citric acid, 10 volume percent H2O2 and 95 °C, 84 percent Al, 84 percent Co, 87 percent Li, 86 percent Mn and 96 percent Ni were leached after 40 min, producing a leach solution containing 0.68 g/L Al, 20.0 g/L Co, 6.0 g/L Li, 13.6 g/L Mn and 19.3 g/L Ni. Using stepwise addition of H2O2, instead of initial bulk addition, did not significantly improve the leaching efficiency but did reduce the required leaching time. Temperature control of the reactor was also more manageable with stepwise addition of H2O2, and evolution of gas was less vigorous. It was observed that the leaching efficiencies of Co, Li and Mn decreased slightly at solid-to-liquid ratios of 50 and 100 g/L, while the leaching of Ni increased slightly. The solution leached at 20 g/L could be stored for six weeks without any spontaneous precipitation. However, solutions leached at 50 and 100 g/L showed changes in concentration after one month of storage, suggesting that processes that have a large material throughput and use high solid-to-liquid ratios around 100 g/L must ensure that the solutions are not stored for extended periods of time.

Apr 1, 2025

By Baron Miya, Keith Hanks, William Edgerton, Francis Fong

The City of Los Angeles capital improvement program includes the construction of a new 35-km interceptor sewer. This sewer will be built as a deep tunnel with finished diameters ranging from 2- to- 4 meters. The project will be constructed concurrently in two phases; an 18-km East-West and a 17-km North-South segment. The new sewer provides additional conveyance capacity for an existing deteriorating sewer that is scheduled for rehabilitation. Large sewage spills during the El Niño storms of 1998 resulted in a Cease and Desist Order that established an aggressive schedule for the completion of the project.

Jan 1, 1999

By S. R. DeBoer

A study of Western cities reveals the fact that a city where people make their homes for permanent residence is always a city with, well-shaded avenues, with parks and playgrounds; in other words, a beautiful city. On the other hand, the average city that lacks these qualifications is usually a city of transient population. Many of our Western cities must be classified as such. Their inhabitants live in such a city only to the time that they will be able financially to retire from business and go to one of the other types of cities to live; or until opportunity offers itself for a position or a job in such a city. I believe that our Western coal camps could benefit by this truth. If conditions can be created in the camps that will encourage the workers to settle permanently or for a long time at least in the town, it would greatly aid in stabilizing employment. By the term "workers" I do not mean the pick and shovel men alone, but everybody from the superintendent or the manager down; for the educated part of the population suffers probably greater from a desire for better surroundings than the less educated part. Modern City Planning tries to show the way for more attractive towns; for more practical towns also, and at less expense. The grid-iron system of street planning is slowly being replaced by one that fits the contours of the site. Instead of streets that are cut through the hills and built over the valleys to get practical grades, it tries to show how these streets can be made to fit the ground and produce better traffic lines; greatly more attractive streets; better building sites and lots, and all of this at less expense. A well-planned town of this character should have as its nucleus, a central square around which the main stores and business houses are grouped. The main building of this group should be the church, the community meeting place, city hall or such other buildings of a public or semi-public character, that are imposing enough to add interest to the square. From this central square, streets should be built to radiate out in all directions, more or less like a spider-web. The main lines of these streets should be reserved for traffic purposes and they should be wide, for the town may grow into a city, and they should be direct, connecting the town center with outlying points at the shortest and easiest possible line. Between these radiating streets should be residential streets of narrower width and arranged in such a way that fast through traffic cannot pass over them and make them unsafe and unsanitary for family life. Following up the comparison with the spider-web, the town should have circular streets, encircling the whole town with rings at various distances out, along which circular lines parks should be located. In the West, where the need for shade is so great, the town should surround itself with a belt of forest trees. Such a forest belt would break the winds and shelter the town, and also make the whole town a cozier, nicer place to build a home in. A forest belt of this kind does not necessarily mean a great layout of money. Trees can be planted small and at little cost and a carefully studied irrigation system will make the maintenance cost small. If the town has any places of natural beauty they should be carefully preserved and made accessible. Natural parks of this type will often take the place of the artificial parks of large cities, and at no expense to the community. Playgrounds, a swimming pool, either of concrete or a sanded beach on a lake; a place for all to go skating in winter; a hill for sledding in

Jan 1, 1924

By Charles E. Hughes

HERBERT HOOVER had to sit through an hour and a half of eulogy of himself at Carnegie Hall last night, said the Sun and New York Herald of Feb. 19. When his turn to answer came he remarked that, although one of the speakers had referred to him as a modest man, he would never, in view of this experience, be able to prove it. The occasion was the presentation by the Civic Forum to Mr. Hoover of its medal of honor for distinguished service, the only recipients in past years having been General Goethals, Thomas A. Edison, and Alexander Graham Bell. Only by distortion of intent could there be said to be anything political in the affair, which was carefully described by the chairman, Charles E. Hughes, as non-partisan. Nevertheless, the praise bestowed on the former Food Administrator by the former Republican candidate for President, proved specially interesting to a much applauding audience which filled the hall to the uppermost gallery. A piece of real news was supplied by Horace V. Winchell, whom Mr. Hoover succeeded on Tuesday as President of the American Institute of Mining and Metallurgical Engineers. He said that Mr. Hoover, when in Europe after the . armistice, caused to be collected the literature of the war in all Europe.

Jan 1, 1920

By Klaus W. John

The geologic factor of greatest significance in rock mechanics and rock engineering is considered to be the geologic structure represented by joints, faults, and other planes of weakness. This geologic structure differentiates between the rock element and the rock system composed of these elements. Only during the last decade has the difference of the technological properties of element and system been recognized but this appears to be more in theory than in engineering practice. If rock mechanics is to achieve real significance in engineering practice, it has to provide methods of analysis which are realistic compromises between the best representation of the actual conditions and pragmatic engineering. The rock mechanics practitioner has to face the fact that many geological engineering and rock mechanics problems may be too complex to allow rigorous analysis but at the same time are deemed satisfactory for the construction of major structures. Ultimately, the geotechnical engineer or the engineering geologist has to express the effect of geologic factors in quantitative, even if approximate, terms and provide numerical data on strength and deformability of rock systems to be utilized in construction. Qualitative evaluations, quantitative descriptions of geologic features as such, and comparisons of specific test results are always of interest but may not suffice as basis for engineering decisions and designs. The present efforts of the rock mechanics group at the Karlsruhe University, Federal Republic of Germany, are based on a systematic combination of geomechanical models and numerical analyses based on the finite element approach. This group considers that at the present stage

Jan 1, 1970

By John Goodell

CIVIL engineers seem to number in their ranks more advocates of licensing than are found among the practitioners of other branches of the pro-fession. Licensing was not originated by civil engineers but it was forced upon them in two ways. In the first place, the civil engineering profession has hangers-on like every other profession. The first legislative result of their imperfect accomplishments with which I am familiar occurred in the far West. It was found that early irrigation works were so badly planned in some cases that not only were water rights made very uncertain but considerable sums were invested in structures and ditches which proved inadequate and occasionally complete failures. Water was too valuable to be wasted in that way and money too hard to obtain. In those sections, therefore, laws were passed many years ago which made it obligatory for the design of irrigation works and other structures utilizing water to be made by engineers who had satisfied a board of examiners that they possessed the technical qualifications to plan such works properly. The basic thought on which such laws rest is the same as that on which laws governing the licensing of boiler operators rest, namely, the safety and welfare of the public. While boiler explosions still occur and irrigation works are built which are not wholly satis-factory, these laws have helped the, public, it is gener-ally agreed.

Jan 4, 1922

By Dave Kay, Young-Suk Song

To meet the needs of South Korea's rapidly expanding economy, a large number of infrastructure projects are under way to improve transportation efficiency within the nation. These projects include high-speed rail links between major population centres and improvements to the road network. Being densely populated and geographically mountainous, infrastructure development in Korea requires a significant amount of tunnelling. Owing to the predominantly hard granitic nature of rock, drill and blast is the preferred method of tunnel advance. The Korean tunneller, however, faces the same pressures as those of his international counterpart in that both cost and production targets need to be achieved while meeting expectations of both community and regulator.

Jan 1, 2005

By Jackson E

The general level of awareness amongst members of the professions that they are faced with an increasing number of claims for breaches of their professional duty was dramatically heightened by the decision of Rogers J. at first instance in Cambridge Credit Corporation v Hutcheson (1985) 3 ACLR when the auditors of the failed company were found liable for breach of contract and faced a damages award of $145 million - well in excess of their insurance cover. No comfort should be found in the fact that this decision was overturned on appeal, for that result rested on the issue of whether there had been a causal connection between the breach of contract which had occurred and the loss suffered rather than on the fundamental principle of auditors' liability.

Jan 1, 1989

Claiming the Green Revolution - Protecting Investment in Green Mineral Processing

Sep 13, 2010

An upgrade to Vale?s existing Clarabelle dual-pinion, semiautogenous (SAG) mill was completed by the power and automation technology company, ABB. The mill is used to reduce the size of the ore at the company?s nickel and copper mines in the Sudbury area. The project was completed on time and on budget with an excellent safety record. Located in Ontario about 400 km (250 miles) north of Toronto, Vale?s Sudbury operations are primarily underground nickel sulfide mines, with integrated mining, milling, smelting and refining operations. One of the characteristics of Clarabelle Mill is to accept nickel-copper ore from various sources and companies and to produce a nickel-copper concentrate and copper concentrate for further processing. The size of the ore is further reduced in SAG mills, rod mills and ball mills, where all milling is done wet.

Mar 1, 2014

By Langham B. M

A chemical study of the petrographic components of Greta (Maitland) coal, carried out by the Metropolitan Gas Co. (Melbourne), has revealed an anomaly in the composition of the durain which was thought to warrant petrological investigation.The original study, by the Metropolitan Gas Co., extended over eight shipments of coal received during the winter of 1943.The percentages of the several petrographic components were eslimated by careful handpicking of large samples of each shipment, and analyses were made of the handpicked components, which were also tested as to their gas-making and coking properties.The results are summarised in Tables 1 and 2. At first sight the components of the Greta coal bear a general resemblance in composition to those of other bituminous coals of similar rank, apart from a notable richness in volatiles, which is a distinctive feature of Greta coal. The durain has a typically higher ash content, and lower volatile content than the clarain (Table 1); and the coking behaviour of the four components is typical (Fig. 4).When, however, the analyses of Table 1 are re-calculated on a dry, ash-free basis, an anomaly appears: the clarain and the durain, on this 'pure coal' basis, have practically identical compositions, with the durain containing a slightly higher proportion of volatiles than the clarain (cf. Table 3); but the tar yield of these two components is very different (Table 1). Re-calculated on a dry, ash-free basis, the yield from the clarain is 18.9 gallons of tar per ton, while, that of the durain is 29.0 gallons per ton. The gas derived from the durain is correspondingly richer in illuminants (CH etc) and poorer in hydrogen than that from the clarain (Table 2), and is also notably richer in nitrogen.That the composition of the Greta durain is consistent is proved by the analyses of Table 3, in which the compositions of the respective durains and clarains of eight separate shipments of coal are compared. In most bituminous coals, the durain contains several per cent less volatile matter than the associated clarain, and high volatile content in a durain usually indicates a durain rich in spores.

Jan 1, 1947

By Judson G. Brown

In order to filter small amounts of fine slimy solids the reversible cake-filtration process was developed. The filterable solids contents lion in feeds can range from less than 1 ppm up to about 5%. The relative advantages of this process, are usually the greatest in the range of 0.05% to 1.0% filterable solids. Filterable solids that average in particle size about 20 microns& are non-compressible are very easy for this filtration process. Some feeds have been all sub-micron in particle size. A 1/8 inch thick cake is considered to be very thick. The usual cake is between 13/2 and 1/16 inch thick. A new line of injection molded plastic filter plates were developed for use with the reversible cake filtration process. The first commercial sized installation of this system was made 3 years ago in the Wakefield Y.M.C.A. swimming pool. Over 70 filters ranging in size from one plate to 63 plates have been produced. In addition to the process advantages there are the low cost and corrosion resistance advantages of the plastic plates.

Jan 1, 1962

By Rintaro Hayashi

The enrichment of useful components from ores and/or wastes has become important with increasing recent worldwide resources demand and the amount of wastes generated from the urban mines, in order to establish real ?sound resource-cycle society? including the activity of resource exploitation. The first stage of the treatment in the process must be comminution and it is important to make good liberation among compositional phases in the targeted resources. Electrical disintegration (ED) is well known to make a selective breakage at phase boundary. However, the detailed mechanism of the phenomena is not clarified yet, in especial, on the influence of electrical properties of compositional materials on the liberation. This paper made a comparison between the liberation degrees of ED products and the results of electromagnetic field analysis using finite element method (FEM). In the experiments, we used several synthetic cement paste based samples in which mineral particles were dispersed to apply the ED, and in the electromagnetic field analysis, we calculated the charge density accumulated and the Maxwell stress at phase boundary. It was found, for highly insulating mineral samples, that higher breakdown voltage was necessary because electric charge was not easily accumulated at phase boundary but that higher liberation degree was obtained after the breakdown (ED). It was also found the tendency that higher liberation was observed for the samples which had higher maximum Maxwell stress calculated by the electromagnetic field analysis. From the results, the electrical charge and Maxwell stress induced at phase boundary could be driving forces of selective breakage. In addition, we also applied the ED to the printed circuit boards (PCBs) in order to concentrate miner rare metals, which were essential for producing electronic devices. It could be demonstrated that the devices installed on the PCB were easily detached from the board and that most of metal elements in the devices was exposed and liberated from the insulating plastic covers, which were broken in the ED, then, it is considered that the subsequent solid phase separation could be effective for concentrating such metal elements. Keywords: liberation, electromagnetic field analysis, printed circuit board, miner rare metal

Sep 1, 2012

By C. R. Kuzell

ALTHOUGH furnaces constructed of refractory brick have been oper-ated for many decades, there has always been an unfulfilled desire by the operators for a less arduous and more satisfactory method of patching weak spots and burned-out zones in order to postpone and to effectively extend the termination of a furnace campaign. Not only has this desire frequently arisen when small spots have approached incipient failure while the furnace structure as a whole was still in good condition, but also when larger areas showed signs of needing replacement. The availa-ble methods have been arduous, sometimes dangerous, inefficient with respect to the life of new refractory material used, and nearly always have necessitated interruption of the continuity of the furnace operations and therefore reduction in furnace production during the period of time required for the repair work. Most of these older methods have involved the replacement of masonry by refractory shapes in the weakened areas. Many attempts have been made to develop a method of patching the burned-out areas by spraying granular refractory material upon old surfaces. While some success has been attained in attempts to renew the grooved, corroded side walls and fettling, and the edges of hearths, there have been no known successful applications of the spraying method in patching the underside of arches of operating furnaces. The method developed recently at the Clarkdale smelter of the United Verde Branch of Phelps Dodge Corporation, at Clarkdale, Ariz., and described in this paper, has been found to be not only convenient and successful with respect to patching vertical or inclined surfaces, but has met with a marked degree of success in patching the parts of furnace arches that are exposed to flame, the successful result being obtained with-out interruption or interference with the continuity of furnace operations. ? It may be described as a method of renewing the interior refractory sur-faces of operating furnaces by pneumatic spraying of an aqueous suspen-sion of finely divided particles of refractory material. It has been used

Jan 1, 1939

By Edward Cadwell

El presente texto señala la clasificación de combinación de minerales a través los desperdicios estériles y altos y concentrados bajos.

Jan 1, 1959

By Pedro Alejandro Samané Tuni

El presente texto describe las soluciones que disponen los geólogos e ingenieros para actuar de forma adecuada en la planificación, diseño y construcción de los proyectos, así como se muestran los errores de concepto que todavía persisten cuando se usan las clasificaciones geomecánicas.

May 1, 2013

By D. M. Wagner, G. Biggs, M. Osmundson, C. J. Twaroski

Potential air emission impacts to federal Class I areas from distant sources are receiving increasing scrutiny by federal land managers (FLMs). This paper provides summary results of the impact analyses conducted for FLMs and PSD permitting of a proposed expansion for a taconite processing facility. Results from air quality increment, acid deposition, mercury deposition, and visibility analyses for Class I areas located 50 to 162 km from the facility showed the project would meet the respective regulatory and guideline values for the specific analyses. During the course of the air quality analyses, potential new requirements from the FLMs’ Air Quality Related Values Workgroup (FLAG) efforts and USEPA’s Regional Haze Program were brought into the PSD discussions. The implications for these future guidelines and regulations as they may affect future expansions at other mineral processing facilities are also discussed.

Jan 1, 2001

By Yogesh Prashar

Three conventional uplift tests and 12 Rapid Pile Load Tests (RLT) were performed on total of fifteen 16-inch square pre-cast concrete driven piles at a test site in Emeryville California in December of 2000. The uplift tests were performed in accordance with ASTM standards, and the RLTs were performed using a FUNDEX RLT. The RLT is carried out by dropping a mass of 25-tons on top of the pile, thereby inducing a force that is measured by a load cell. An optical lens records the vertical deflection of LED's that are mounted on the pile. Ultimate uplift and compression capacities of each of the fifteen piles were determined using the Davisson method. Soil parameters were calibrated by back-calculation (cohesion and internal angle of friction) using both the results of conventional uplift load versus deflection curve, as well as the results of the triaxial compression tests. A two-dimensional finite difference model including soil elements, and structural elements representing the test pile was setup using the computer program Fast Lagrangian Analysis of Continua (FLAC). FLAC was used to simulate both the uplift as well as the RLT. Strength increase of cohesive material was also accounted for in the analysis. Numerically simulated and theoretically computed pile capacity curves and axial deformation variation with applied load curves are in close agreement to the observed curve during the field test. Conclusions are made from this test site regarding the factors influencing results of RLT.

Jan 1, 2002