Search Documents

By Cyril S. Taylor, Junius D. Edwards

Magnesium is the lightest metal used for structural purposes, for which reason perhaps more than usual interest is attached to measurements of its density. Although the density of solid magnesium has been det,ermined frequently, no measurements of the density of the liquid metal are available. Because of unusual experimental difficulties in measuring the density of the liquid, only a limited number of measurements of good precision were secured. The results, especially the value for the crystallization shrinkage, are of great interest in connection with the casting of the metal. A number of samples for these measurements were made available through the courtesy of the American Magnesium Corp. They were in the form of extruded bars 3/8 in- in diameter and several were of exceptional purity, as indicated by careful analyses. Table 1 gives the density values (at 20" C.) for magnesium of varying degrees of purity. The density was measured at room temperature by comparison of the weight in air, and when immersed in distilled water. The necessary buoyancy corrections were applied, so that the density could be expressed in absolute measure—grams per milliliter. The effect of the buoyancy of the immersed suspension and the surface-tension pull of the water upon the suspension were eliminated from the results by a preliminary weighing of the suspension immersed to the working depth. Great care was necessary to prevent the introduction of a significant error by the formation of gas bubbles upon the clean magnesium surfaces; these are sometimes very minute and easily escape observation. They may be detached by raising the specimen from the water and again immersing; this should be done just prior to completing the weighing. Their formation may be almost entirely prevented during a measurement by previously immersing the specimen in a solution of paraffin in petroleum ether. The thin film of paraffin remaining after the evaporation of the solvent prevents wetting of the magnesium surface by the water. In one such determination, the paraffin coating on a 22-gm. Specimen

Jan 1, 1923

By Junius D. Edwards, Cyril S. Taylor

Magnesium is the lightest metal used for structural purposes, for which reason perhaps more than usual interest is attached to measurements of its density. Although the density of solid magnesium has been det,ermined frequently, no measurements of the density of the liquid metal are available. Because of unusual experimental difficulties in measuring the density of the liquid, only a limited number of measurements of good precision were secured. The results, especially the value for the crystallization shrinkage, are of great interest in connection with the casting of the metal. A number of samples for these measurements were made available through the courtesy of the American Magnesium Corp. They were in the form of extruded bars 3/8 in- in diameter and several were of exceptional purity, as indicated by careful analyses. Table 1 gives the density values (at 20" C.) for magnesium of varying degrees of purity. The density was measured at room temperature by comparison of the weight in air, and when immersed in distilled water. The necessary buoyancy corrections were applied, so that the density could be expressed in absolute measure—grams per milliliter. The effect of the buoyancy of the immersed suspension and the surface-tension pull of the water upon the suspension were eliminated from the results by a preliminary weighing of the suspension immersed to the working depth. Great care was necessary to prevent the introduction of a significant error by the formation of gas bubbles upon the clean magnesium surfaces; these are sometimes very minute and easily escape observation. They may be detached by raising the specimen from the water and again immersing; this should be done just prior to completing the weighing. Their formation may be almost entirely prevented during a measurement by previously immersing the specimen in a solution of paraffin in petroleum ether. The thin film of paraffin remaining after the evaporation of the solvent prevents wetting of the magnesium surface by the water. In one such determination, the paraffin coating on a 22-gm. Specimen

Jan 1, 1923

By R. C. Canby

The American water-jacket furnace is the outgrowth of lead-smelting at Eureka, Nev., subsequently developed in Utah and Colorado. Early smelting in Virginia, New England, or the Missouri-Kansas-Illinois district seems to have had no direct influence in the development of this furnace. First Decade, 1870 to 1880. In 1870, the draft-furnace was used in Nevada, coincidentally with the first crude sandstone blast furnaces, which were 2 or 3 ft. sq., with Sturtevant fans or small Roots blowers, and sheet-iron or water-cooled tuyeres. Stetefeldt, Liebenau, Albert Arents, and 0. H. Hahn mere the early metallurgical leaders. Arents's siphon-tap and the re-establishment of the furnace-bosh mere the most important improvements of the decade. Second Decade, 1880 to 1890. At first there were ,many small local plants; but by the time Eureka had reached its maximum production of lead-ore, two custom works (the Eureka and the Richmond) were treating all the ore, the miners having learned the economy of smelting at larger and well-constructed plants. In the early eighties, most of the features of modern practice were already discernible at Salt Lake, Leadville, Denver, and Pueblo. The small square sandstone furnaces had been replaced by rectangular water-jacket furnaces, mostly 36 in. wide, and from 60 to 80 in. long at the tuyeres, which entered between cast-iron water-jackets. Subsequently, Franz Casin, at the Holden works, Denver, put the tuyeres in the middle of the jackets, and many other improvements were made by him and others, so that the cast-iron jacket became the favorite, until the possibility of

Jan 1, 1913

By Ernst F. Eurich

Alexander Parkes patented in England in 1851-52-53 a process for desilvering lead by means of zinc, making use of the greater affinity of silver for zinc than for lead, discovered by Karsten in 1842. The efforts in England to develop it commercially were not particularly successful, nor was the attempted introduction into the United States. This last was not surprising, as it was about the beginning of our Civil War, and at that period there was very little lead-bullion produced in the United States and there was no field for the process here. There was at that time on Staten Island an establishment that pattisonized lead, probably from Rossie, N. Y., and Chester, Pa., and possibly some Spanish lead, but the production of lead-bullion in the Far West had not yet begun. In 1864, Edward Balbach, of Newark, N. J., patented in this country a process for desilvering lead by means of zinc, and in 1867 Edward Balbach, Jr., patented a " movable black-lead retort with a neck, placed in a furnace," for the purpose of distilling the alloy of zinc, lead, and the precious metals. A brief comparison of the Parkes and the Balbach processes is interesting. The Parkes process as practiced in England consisted in stirring into silver-bearing lead, melted in a kettle, from 1 to 2 per cent. of zinc, cooling, skimming the alloy of lead, zinc, and silver that rose to the surface, liquating it in an iron retort, distilling the residual rich alloy in fire-clay retorts, thus regaining the zinc, and refining the desilvered lead at a low heat in a shallow cast-iron pan that formed the hearth of a reverbera-tory furnace. If the lead was too impure, it was first softened

Jan 1, 1913

By Charles H. Eldridge, Robert J. Anderson

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By Robert J. Anderson, Charles H. Eldridge

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By Albert E. Greene

Processes for the removal of phosphorus from iron or steel are steadily assuming greater importance in view of the abundance of high-phosphorus iron-ore and the diminishing supply of pure ore. In the present methods of removing phosphorus by the basic open-hearth or basic Bessemer process, or even by electric processes, complete control over the metallurgical conditions is either impossible or has not yet been realized. The removal of phosphorus has so long been accomplished along certain well-defined lines, that when the electric furnace made its appearance metallurgists adhered to the same old reactions used in the older processes and failed to appreciate and take advantage of the new forces at their disposal. One object of the present paper is to set forth more clearly the metallurgical reactions by which phosphorus can be removed from iron, and to show the necessity of controlling the conditions, and particularly the temperature, by means other than combustion in the furnace-chamber. Invariably, the commercial removal of phosphorus has been accomplished by oxidation. The reactions involved in oxidation of phosphorus in general consist, first, of the formation of P2O5 and second, the combination of this oxide with lime, forming calcium phosphate, which latter is held in a slag high in iron oxide. In the present-used processes, the phosphorus is never removed without the assistance or presence of considerable quantities of iron oxide. The oxygen for removal of phosphorus in the basic open-hearth process comes largely through the medium of iron oxide and furnace-gases, but not

Jan 1, 1913

By A. B. Wood

In welding and metal working by electricity, two systems are in use,—the so-called. incandescent system, in which the material operated upon is traversed by currents of large volume and low electro-motive force, the current having a continuous metallic circuit during the welding operation, and the arc system, in which the electric arc is utilized. It is the purpose of the present paper to call attention to this last

Jan 1, 1892

By J. B. Nau

A short time ago some interesting experiments concerning a new steel-making process in the open-hearth furnace were made by the writer at the Croton magnetic mine, N. Y.

Jan 1, 1892

By George Ross Green

[In discussion of the paper of Mr. J. C. Bayles, read at the New York meeting of September, 1890, Trans., xix., p. 18.1 It is often so difficult to locate the causes of failures of machinery and apparatus which can be examined and studied at leisure, that it is not surprising that the causes of explosions should escape detection. Usually the explosion is the first evidence that anything is amiss, and the time for observing the conditions is necessarily brief. An incident in a welding-works near Essen, Germany, might be cited as exemplifying what trifling causes may lead to disaster, and how difficult, under the most favorable conditions, it may be to discover them. A blowing-engine was arranged with two suction-pipes at each end of the blowing-cylinder—one leading to the air, and the other to the gas-holder. Each pipe was provided with a valve, and all were so adjusted that the cylinder drew in gas and air in the proportions found most advantageous. The gases from the cylinder were carried directly to the furnace through suitable pipes, and while the cylinder was provided with relief-valves, every effort was made to prevent explosions, principally by compressing the gases to a point where the rate of efflux of the mixture was greater than the velocity of combustion, if the expression is here allowable. It was found that the apparatus would work satisfactorily for some time, and then the relative proportions of the mixture would change, and an explosion might have been the result. Experiments consuming days were made to discover a method of averting this danger, but they were unsuccessful, until it was observed that the change in the composition of the mixture of gas and air took place when the gasometer began to rise or fall—the back-pressure due to friction when the holder was rising or its absence when falling being sufficient to change the conditions. As soon as this was discovered,

Jan 1, 1892

By George J. Young

The recurrence of mine-fires in Nevada during the past decade is not only a matter of interest, but also one of considerable concern to engineers and mine-managers. The more important fires may be enumerated as follows: Forman Shaft fire, Gold Hill, April 21, 1903; shaft-house, machinery, and shaft destroyed; loss estimated at $50,000; cause unknown. Union Shaft fire, Virginia City, July 14, 1904; shaft-house, machinery,and shaft in part destroyed; loss estimated at $100,-000; cause of fire stated as the careless throwing of a match in the rope-house. Sutro Tunnel fire, Virginia City, Jan. 27, 1909; 700 ft. of tunnel-timbering destroyed, and direct damage of $10,000; cause " probably electric wires." Belcher Shaft fire, Gold Hill, Aug. 9, 1910; shaft-house destroyed, machinery ruined, and upper part of shaft damaged; damage, $25,000; no cause given. Belmont Mine fire, Tonopah, Feb. 23, 1911; fire started ill winze; 17 men killed. Giroux Mine fire, Kimberly, Aug. 23, 1911; fire originated in shaft-station from unknown cause; 7 men killed, and $34,-521 damage caused. (Note 1.—On June 11, 1912, some time after the present paper was written, a fire broke out in the pump-room on the 2475 station of the Ward shaft, Virginia City. This fire was caused by the short-circuiting and exploding of the starting-switch on No. 5 pump. The oil in the switch was scattered about and set fire to the timbers and lagging of the pump-room. The pump-man in charge notified the surface, and the electric current was shut off. A hose was then turned on the fire, but the dense smoke drove the attendant out. Inspection by the electrician and the shaft-foreman, equipped with oxygen-

Jan 1, 1913

By John Jermain Porter

The chief purpose of this paper is to indicate the laws governing the fuel-economy of the cupola, to examine the feasibility of some of the proposals for increasing its fuel-economy, and to show that the conditions limiting fuel-economy here are altogether different from those prevailing in the blast-furnace. The two methods available for studying the thermal efficiency of the cupola and determining the factors limiting fuel-economy are: 1, by the determination of the total heat-balance; and 2, by the application of the theory of critical temperatures. The case selected as an example represents a cupola operating under fairly efficient conditions. The data are as follows : Cupola, GO in. in diameter, 15 ft. high to the charging-door, with a 9-in. lining. Bed-charge, 2,000 lb. of coke and 4,000 lb. of iron. Subsequent charges, 400 lb. of coke and 4,000 Ib. of iron. Total number of charges, 20. There was 800 lb. of coke recovered from the drop, hence the total coke burned is 8,800 lb., or 0.11 lb. of coke per Ib. of iron. Coke contains 90 per cent. of fixed carbon and 2 per cent. of moisture. 300 1b. of kindling-wood is used in lighting. 80 lb. of limestone (95 per cent. of CaCO,) is used per charge, or 0.02 lb. per Ib. of iron. Melting-loss, 4 per cent.; distributed thus : Fe, 3.5; Si, 0.25; Mn, 0.25 per cent. Average analysis of top-gases : CO2, 15.1; CO, 10.0 per cent. Average temperature of top-gases, 1,600" F. Temperature of air and stock charged, 60" F. Dew-point of air, 50 F. The items entering into the total heat-balance and their calculation are as follows: 1. Heat of combustion of fuel.—Total heat evolved = 14,580 x lb. of carbon burned + 7,200 X Ib. of wood burned. Hence B.t.u. per lb. of iron charged =

Jan 1, 1913

By George Asmus

Closed front, or open front for blast-furnaces, has been for a number of years a much discussed question among the furnace-men in every country where iron is made. As blast-furnaces are costly structures, and as the whole question is one of economy, I hope to be excused for entering a little into details. The "fore-hearth" is a prolonged opening in the lowest part of the hearth, from two to three feet wide, four to six feet long, and two to three feet high. It is a more or less fire-proof box, cooler than

By Charles E. Hall

The Crimora mine, operated by the American Manganese Company, Limited, is located 21/2 miles east of Crimora station, 011 the Shenandoah Valley railroad, in Augusta county, Virginia. It is situated in a basin at the western base of the range of mountains which flanks the Shenandoah Valley on the east. This range is composed of the Potsdam sandstone (No. I. of the Pennsylvania survey), and extends in a northeasterly-southwesterly direction the entire length of the valley. The general dip of the measures is westward. The massive sandstone of the mountain is geologically overlaid with shales or slates, which belong to the Potsdam, or lie between it and the Lower Silurian limestone. Throughout this region these shales are decomposed, and form more or less extensive clay deposits, which are found along the base of the range and often underlie a considerable area to the westward of the abrupt slope of the range. Sand and fragments of quartzite occur in considerable quantities on the surface, and often conceal the true character of the underlying formation. The area containing this ore-deposit extends northeast and south-

Jan 1, 1892

By F. A. J. Fitzgerald

In any kind of furnace the question of preventing the loss of heat is important, for no matter how the heat is obtained it costs something; and consequently, other things equal, that furnace is most desirable which uses the greatest percentage of the total heat generated for the particular object in view. In the furnace which uses electricity for the generation of heat the importance of preventing losses of heat is very much greater than in any other. To generate 1,000 kg-cal. requires an expenditure of 1.16 kw-hr., and consequently the cost per calorie is always expensive when electricity is used for heating. In heating any material in a furnace a general rule is that the generation of heat should be as rapid as possible. In any given furnace the heat-losses may be expressed as so many watts, and, therefore, the longer it takes to heat the furnace-charge the greater the losses will be. Suppose that a furnace contains a charge to be heated to 1,500°C. and that the average loss of heat is at the rate of 100 kw., then if the process of heating the charge takes 1 hr. the losses will amount to 100 kw-hr.; but if by using a more rapid generation of energy the charge can be heated in 30 min. the losses will amount to 50 kv-hr. An example from experiments on a certain process may be given to illustrate this point. The problem was simply to heat a furnace-charge to a certain temperature, and experiments were made to determine the effect of increasing the rate of generation of energy and comparing the kilowatt-hours required to heat a given charge. Here are typical results : Rate of Generation Energy Per Kg. of Energy. of product 88 kw. 1.7 kw-hr. 93 kw. 1.6 kw-hr.

Jan 1, 1913

By John B. Pearse

The works heretofore used in carrying out the Bessemer process have been constructed substantially as follows: The whole works or plant has been divided into three parts. 1. The division in which the metals for conversion are melted. 2. The division in which the metals are converted into steel and cast into ingots, or the converting department. 3. The engine and boiler department which supplies the hydraulic power required to move the machinery, and which furnishes the blast used for converting the crude metal into steel.

By John W. Langley

The unsatisfactory character of most, if not all, of the processes for the direct determination of alumina in the presence of iron and phosphoric acid, and the sharpness with which both the iron and phosqhoric acid can be determined, have led chemists to rely mainly

Jan 1, 1892

By John B. Pearse

In view of the great importance of accurate knowledge respecting the chemistry of iron and steel, as related to their physical properties, I come before you with a paper showing the great mass of work which has been heretofore done on the subject. I have tabulated the more important data I bring at this time, so as to draw out the results clearly. This information is accessible to all who will seek for it. I have made it the basis of my own practice throughout, and such knowledge is undoubtedly the only foundation for the successful practice of metallurgy. As is well known the ordnance corps of our army, after 1841, made exhaustive experiments on the properties of cast-iron. The investigations were undertaken in order to obtain necessary information on the reorganization of the corps. I wish to call your attention to the results obtained by a comparison of the chemical and physical properties of cast-iron for guns, to describe certain characteristic peculiarities of steel, and to give a brief history of the chemical work relating to carbon in iron. The Reports on Experiments on the Strength and other Properties of Metals for Cannon, published by H. Carey Baird, Philadelphia,

By W. J. Keep

Manganese is a nearly white metal, having about the same appearance when fractured as white cast-iron. Its specific gravity is about 8, while that of white cast-iron, reasonably free from impurities, is but a little above 7.5. As produced commercially, it is combined with iron, and with small percentages of silicon, phosphorus, and sulphur. It is generally produced in the blast-furnace. If the silicon is under 0.50 per cent., the product will be white. If the manganese is under 40 per cent., with the remainder mostly iron, and silicon not high enough to make the product gray, the alloy is called spiegeleisen, and the fracture will show flat reflecting surfaces, from which it takes its name. With manganese above 50 per cent., the iron alloy is called ferromanganese. As manganese increases beyond 50 per cent., the mass cracks in cooling, and when it approaches 98 per cent. the mass crumbles or falls in small pieces. When the percentage of manganese is high, the planes of the fracture are not so bright as when it is lower. The ferro-manganese which we have used in the experiments reported in this paper, contains Mn, 81.62; Si, 0.256 ; and combined carbon, 6.153 per cent. We have not been able to make test-bars from this, because the alloy cracks in small pieces in cooling. Manganese combines with iron in almost any proportion, but if an iron containing manganese is remelted, more or less of the manganese will escape by volatilization, and by oxidation with other elements present in the iron. If sulphur be present, some of the manganese will be likely to unite with it and escape, thus reducing the amount of both elements in the casting. Hence, in remelting irons, some of the sulphur which has entered from the fuel with which the iron is melted will very likely unite with some of the manganese in irons which make up the mixture and escape. Remelting, therefore,' reduces the percentage of manganese in cast-iron.

Jan 1, 1892

By M. G. Corson

Information regarding the use of ixanganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists. Properties of Manganese Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850" C. and the other below 650" C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the sili-cides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. Manganese as a Scavengek Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.