Search Documents

By William Gates, Gabe McClain, Thomas Pallua, Joe Schrank

The Tennessee Capitol Corridor connects the Cordell Hull Building (CHB) to the State Capitol, which isa 232-foot-by-124-foot (71 x 38 m) structure in Nashville that includes porticoes built from local massive limestone. This connection was affected by the Capitol Connector Pedestrian Tunnel (CCPT) project, which is part of the overall Cordell Hull State Office Building and Central Services Demolition, New Construction and Renovation Project (Cordell Hull Renovation Project). To construct this connection, the two existing elevator shafts and a new emergency stairwell in the State Capitol were extended down to anew lobby area—the elevators by about 50 feet (15.2 m) and the stairwell by about 60 feet (18.3 m). This lobby was connected to the CHB by a 435-foot-long (133 m) pedestrian tunnel. It was predicted that most of the tunnel would be excavated in a relatively strong limestone; therefore, considering the project features and constraints, drill-and-blast techniques were selected as the primary excavation method. Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds. To calculate the ground response factor, the scaled distance of each shot was compared to the ground vibration as PPV, generating a subsequent regression curve with an R2value of about 0.7. Using the best fit curve equation, the estimated ground response factor was about 150 for the best fit line. Other than some cases with relatively high (> 2 in./sec [51 mm/sec]) recorded PPV values, the blasting operation was successfully conducted as planned and the observed strain on the monitored buildings was very low, mainly within ±2 με (0.0002% elongation). (In general, the recorded PPV was lower than 2 in./sec at frequencies of more than 50 Hz.). The strain gauges at key locations (cold joints and old fractures) in the Capitol and on other critical structures demonstrated strain was insignificant in relationship to ground vibrations from the blasting operations. The apparently small vibration-induced strains were related to the massive limestone construction of the Capitol and ancillary buildings, as the induced strain plus the existing strain did not exceed the critical strain of the massive structures.

By Gabe McClain, Thomas Pallua, Joe Schrank, William C. Gates

Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds

Feb 1, 2020

By Carlson BL, Overton DD

This paper compares the designs of heap leach facilities for four precious metal mining projects in the southwestern United States. These four proposed projects are of small-to medium-size relative to other operating mines in the United States, and are either permitted or in the final stages of permitting. The differences and similarities in the heap leach facility designs are compared with respect to site conditions, operating conditions and regulatory requirements. This comparison provides a summary of the state-of-practice for heap leach facility design in the southwestern United States and identifies current issues in project development and process material containment.

Jan 1, 1997

By C McGuire

As mobile equipment electrification in underground mining continues to gain popularity, control ofheat and humidity in the workplace is becoming a key driver in sizing of ventilation and mine aircooling systems. For design and sizing of ventilation and cooling systems to be accurate, and for themine mobile equipment fleet to be sized appropriately to meet production goals, vehicle productivitymetrics, heat modelling, and energy balances for electrified fleets need to consider operation througha realistic duty cycle that is reflective of various tasks performed during a shift.The authors conducted a real-world comparison of two 8 cubic yard (14 metric tonne) class Load-Haul-Dump (LHD) machines – one diesel and one battery-electric vehicle (BEV) – performingidentical muck-haul-dump operations on consecutive days at an underground nickel/copper hardrock mine in Ontario, Canada.The battery-electric LHD averaged 8.9 per cent faster cycle time than the diesel vehicle (gross,without accounting for charging time), and was able to transport 25 per cent more material per cycledue to a larger bucket capacity. When including the charging time, average net cycle times wereequivalent for the two vehicles over the 200 cycles. The BEV carried more payload over the eighthour period due to the increased capacity per cycle.The testing identified an approximately five-fold reduction in heat output from the BEV in comparisonto the diesel LHD on a basis of heat output per tonne of rated bucket capacity. Heat output from thefast charger was found to be approximately 4 per cent of the charging rate, with negligibletemperature change observed in the main drift. External noise levels in the mine were found to be14 dB lower for the BEV during transit and 11 dB lower during bucket loading. Fuel/energy costs forBEV electricity input were approximately four times lower per operating hour than diesel fuel costbased on typical 2021 electrical and diesel unit rates for a grid-connected mine in Ontario, Canada.

Oct 12, 2022

By Robert R. Tarver

A long history of gold production at Nome, Alaska has resulted in long term interest in the nearshore environment as a production target. Mining by Western Gold Exploration and Mining Company offshore of Nome yielded approximately 100,000 troy ounces of gold in the period 1986 through 1990. This study was designed to determine the relationship between heavy minerals, sediments, and gold concentrations which occur in the upper meter of sediment offshore of Nome. Standard procedures were implemented for grain size analysis, heavy mineral separations, and heavy mineral frequency determination.

Jan 1, 1991

By Tapan Goswami, Michael Croucher

At Bayswater Colliery various methods of controlling highwall stabii were investigated. The use of presplitting was trialled and its effectiveness measured. The presplit hole spacing and explosive charge were based on those succes& lly used in other coal mines in the Hunter Valley. The major presplit design parameter to be determined was the stand-off distance between the presplit line and the back row of the production blast. This could not be transfmed directly from other sites due to the difference between the Bayswater’s production blast geometry and geology to that of other sites. Using highwall face surveys and Orica’s SUR..YPlus@ software, the average back-break behind normal production blasts was determined. This was then used to select the stand-off distance between the back row production blastholes to the presplit line. While presplit designs are normally based on powder factor (kg/m2), the use of energy factor (MJ/m2) was also investigated as a possible design criteria.

Jan 1, 1999

By Amos Bryant, Jesse Davis

This paper compares the predictions of the latest Institute of Makers of Explosives Safety Analysis for Risk (IMESAFR) model versus physical test data recovered from ISO-1 and ISO-2 tests in Woomera, SA. ISO-1 testing included placing 1054 kg (2324 lbs) of ANFO (ammonium nitrate-fuel oil) inside an ISO container on a flat bed truck. ISO-2 testing was identical except the NEW was 4000 kg (8818 lbs). The IMESAFR predictions are based on model runs using the best match available to the actual donor type involved in the test. This type of debris analysis is not the standard output of IMESAFR, as the program is designed to assess the probability of human fatality. However, all of the IMESAFR predictions presented were obtained from the use of the actual model equations and algorithms without adjustment. Test results from ISO-1 and ISO-2 will be presented as well as findings from the comparison between model results and actual explosive results from the ISO testing efforts.

Jan 1, 2010

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT?s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

By F. Shi

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT’s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

By Susan T. Bagley, Linda D. Gratz, Kirby J. Baumgard

The extensive use of heavy-duty diesel engines in underground mines has raised concerns about the potential adverse health effects to miners exposed to diesel particulate matter (DPM) which contains mutagenic and carcinogenic organic compounds. The purpose of this study was to compare the levels of DPM, biological activity, and polynuclear aromatic hydrocarbons (PAH) attributable to diesel engines in underground coal mines and similar data collected in engine laboratory facilities to assess whether laboratory data could be used to predict in-mine levels of diesel emissions. Mean in-mine DPM and SOF concentrations varied from 0.90 to 1.9 mg/m3 and 0.08 to 0.40 mg/m3, respectively. DPM-associated mutagenicity (mean) levels at two of the mines varied from 400 to 970 revertants/m3. Concentations of three PAH differed by up to four-fold between two of the mines, largely reflecting differences in DPM and SOF levels. The laboratory raw exhaust data were divided by 100 to obtain expected or predicted values for in-mine concentrations. The predicted DPM, SOF, mutagenicity, and PAH values based on laboratory samples were not significantly different from many of the in-mine values. Using a potential in-mine dilution ratio range of 20 to 200:1, virtually all in-mine data fell within the predicted range. Therefore, an estimate of in-mine concentrations can be determined by evaluating laboratory data. This will allow for extrapolations from laboratory tests with particulate emission control devices to assess potential health-related benefits due to their in-mine use.

Jan 1, 1991

By Richard L. Stowe

Four NX-diameter holes were diamond-drilled in competent granite. Samples of the recovered core were used in laboratory tests. A borehole, plate-bearing device known as a Goodman jack was used to perform load deformation tests on the rock in the core hole. The majority of samples used in the laboratory tests were taken from depths in the hole at or within 5 ft of those at which the plate bearing tests were made. Borehole camera records, compressional and shear wave velocities, and densities were measured. Dynamic elastic constants were computed for the in-situ material, while comparative data (except camera records) were obtained in the laboratory. These data were examined to evaluate the significance of the in-situ modulus of deformation (Ed), the value computed from Goodman jack tests. Average test results show an excellent correlation between in-situ and laboratory data. The ratio of laboratory to field deformation modulus ranges from 9.82 to 7.21 for 3,000 and 9,000-psi stress levels, respectively. The dynamic modulus ratio, ED field/Ep lab, is 1.02; the compressional wave velocity ratio, V8 field/V8 lab, is 0.94; the shear wave velocity ratio, V, field/V, lab, is 1.12; and the density ratio, field [y/y] lab, is 0.95.

Jan 1, 1973

By A. E. Tercan, D. Mamurekli

Ordinary kriging on the assumption of a gaussian error distribution and indicator kriging were used to derive the probability that a given calorific value would or would not be exceeded by coal from an area of a deposit. The two techniques led to similar probability maps despite local differences; the lack of an absolute reference makes it impossible to judge which method is better for this particular application

Jun 19, 1905

By R. A. Lohnes, S. M. Levorson

As part of research to develop a coal handleability index that predicts the ease with which coal will flow through a handling system, comparative tests were conducted with a Johanson Indicizer and a low-stress triaxial apparatus on 12 coals at a variety of gradations and moisture contents. The lndicizer test provides a rapid method for generating data associated with coal handling characteristics. The arching index measured with the Indicizer is a function of the geometry of the apparatus as well as the properties of the coal. The handleability index determined from triaxial data is a more direct measure of coal characteristics. The handleability index shows a wider range of values than the arching index and, therefore, appears to be more sensitive to coal variations. Neither the arching index nor the ratholing index, as measured with the Indicizer, agreed well with the handleability index. This is attributed to differences in sample preparation as well as to the tests themselves.

Jan 1, 1993

Comparison of Industrial Cyanide Destruction Processes

Sep 13, 2010

By Coopers &. Lybrand

INTRODUCTION From a tax viewpoint, United States mining companies are at a substantial disadvantage in the international mining area compared with companies in other major capital-exporting countries, according to a 1975 study by Coopers & Lybrand for the American Mining Congress. The study compared the relative tax position of a United States investor with investors from Belgium, Canada, France, Germany, Japan, the Netherlands, Switzerland, and the United Kingdom. The comparison was based on average rates of return realizable by investor companies on four mine-model investments in twelve capital-importing countries. The countries in which these investments were assumed to be made are varied in their tax systems so that a wide range of possibilities was included in the analyses. Each mine model was standard so that the rates of return for each investment by each investor were affected solely by the respective tax systems of the capital-exporting and capital-importing countries. UNITED STATES POSITION The study found that the United States competitive position, in terms of the average rate of return on an overall basis, ranked next to last among the nine capital-exporting countries in the study. Further, the United States overall rate of return is more than 20% below that of the country (Japan) with the highest overall rate of return. On an average return-on-equity basis, the United States' position among the nine investor countries, for each of the mine investments studied, was: copper, eighth; iron ore, sixth; nickel, fifth; manganese, a tie for last place. Figure 1 shows the overall results realized by each capital-exporting country on the basis of average return on equity. [ ] The frequency with which a given capital-exporting country attains the highest or next highest rate of return in a capital-importing country provides further insight and another basis for comparing the tax laws of the capital-exporting countries. Of the situations compared in the study, the United States never attained the highest rate of return, and reached the second and third highest rate of return in only two instances. The tables showing the frequencies of rankings are given in Table 1 for each of the four mine models. In summary, the United States mining company does not have a competitive advantage under the tax rules when competing for mineral concessions in other countries. The United States company, in fact, appears to be at a clear disadvantage. The study also considered the effect of the following recent tax proposals on United States investors in international mining ventures:

Jan 1, 1985

By Johan Gjødvad, Catherine Aimone-Martin, Charles Dowding, Mathias Jern

A residential structure adjacent to a quarry in Ohio was instrumented to record structure motions, resulting wall strains and existing crack displacements in response to close-in blasting within 82 m (270 ft). The project is a cooperative effort among international experts representing the European Federation of Explosives Engineers (EFEE) and ISEE supported by more than 21 persons from eight different countries to compliment prior work performed at the Aitik Mine in northern Sweden. The focus of this study is to compare blast-induced vibration measurements relative to regulatory compliance limits as a percentage of allowable velocities among eight different countries for a one-story residential wood-frame structure with a brick-and-mortar exterior and full basement. Participating counties included Austria, France, Germany, Norway, Sweden, Switzerland, the United Kingdom (UK) and the United States (US). Geophones were placed on the foundation and in the ground in accordance with each country’s regulations to record peak velocities as a function of frequency or distance to blasting. This study extends the work performed at the Aitik Mine to include interior corner geophones to calculate global wall strains and micro-m (micro-in) displacement gauges mounted over an existing drywall crack to measure blast-induced dynamic crack responses and climatological influences on daily opening and closing of a crack. Structure responses were documented for 68 blasts conducted north of the structure from February through September 2023 of which 17 blasts were selected for detailed analyses. The highest in-ground PPVs recorded were 43 mm/s and 59 mm/s at the NE and SW corners, respectively. Measurements from these blasts plotted within each country’s limits provided a comparison of stringency among the counties. The percentage of compliance limits among counties ranged from an average of 114% for the US, UK, and Austria limits to the highest of 585% for Switzerland. Despite these high percentages of compliance for all countries, the global tensile strains induced by these blasts were at most only 12 μ-strains and occurred with the highest velocity blast that exceeded each county’s limit. This high percentage of compliance and low strain level demonstrates the restrictive nature of the regulations studied. Peak dynamic crack opening and closing during blasting averaged 20 -m (0.0008 in) while the 12-hour weather-induced crack displacement during the time period over which blasting occurred averaged 200 -m (0.008 in) and the largest 12-hr change in crack width was 356 -m. This low level of crack response validates the observation that the studied regulations have highly conservative limits for cracking potential of standard building materials.

Jan 21, 2025

By N. Kumar Kittusamy, Richard E. Miller

This field study evaluated a newer and older dozer at a construction site. Both dozers performed similar activities in the same location within the construction site. Two operators participated in this study. One operator used the older equipment and the other operator used the newer equipment. Jolting and jarring measurements were taken at the seat/operator interface and at the floor of the cab. The result of this field study indicates that the newer dozer was better than the older dozer.

By Jessica M. Wempen, Michael K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DlnSAR), a satellite-based remote sensing technique, has potential application for measuring mine subsidence on a regional scale with high spatial and temporal resolutions. However, the characteristics of Synthetic Aperture Radar (SAR) data and the effectiveness of DlnSAR for subsidence monitoring depend on the radar band (wavelength). This study evaluates the effectiveness of DinSAR for monitoring subsidence due to longwall mining in central Utah using L-band (24 cm wavelength) SAR data from the Advanced Land Observing Satellite (ALOS) and X-band (3 cm wavelength) SAR data from the TerraSAR-X mission.In the Wasatch Plateau region of central Utah, which is characterized by steep terrain and variable ground cover conditions, areas affected by longwall mine subsidence are identifiable using both L-band and X-band DlnSAR. Generally, using L-band data, subsidence magnitudes are measurable. Compared to X-band, L-band data are less affected by signal saturation due to large deformation gradients and by temporal decorrelation due to changes in the surface conditions over time. The L-band data tend to be stable over relatively long periods (months). Short wavelength X-band data are strongly affected by signal saturation and temporal decorrelation, but regions of subsidence are typically identifiable over short periods (days). Additionally, though subsidence magnitudes are difficult to precisely measure in the central Utah region using X-band data, they can often be reasonably estimated.INTRODUCTIONDifferential Interferometric Synthetic Aperture Radar (DlnSAR) is a satellite-based remote technique that can be used to measure surface displacement over large regions with high spatial resolution. Under good conditions, displacements can be measured with centimeter to subcentimeter accuracy (Buckley, 2000; Massonnet and Feig!, 1998). DlnSAR also has high temporal resolution, and imaging periods typically range from 10 to 50 days (Rosenqvist, Shimada, and Watanabe, 2004; Roth, 2004). In the last two decades, the application of DlnSAR for mine subsidence monitoring has been demonstrated in coal basins in Europe, Australia, China, and the United States (Camec and Delacourt, 2000; Ge, Chang, and Rizos, 2007; Ge et al., 2008; Ismaya and Donovan, 2012; Ng et al., 2010; Perski, 2000; Perski and Jura, 2003; Popiolek and Krawczyk, 2006; Wegmuller et al., 2005; Wright and Stow, 1999; Zhao et al., 2014; Xinglin et al., 2014). Overall, these studies have demonstrated good data resolution, strong relationships between mine development and subsidence, and reasonable agreement between displacements measured by DinSAR and displacements measured by conventional surveys."

Jan 1, 2016

By R. R. Cellan

There have not been many opportunities to date for comparison between laboratory and commercial neutralization rinse data. Homestake Mining Company's Santa Fe project is one such comparison. This paper discusses laboratory procedures and results from a 100' leach pad height simulation column neutralization rinse test and compares principal data with that achieved in actual commercial leach pad neutralization rinsing procedures. Principal comparisons include the rate of WAD cyanide neutralization, decrease in effluent pH, stabilization of dissolved silver and copper, and the quantity of dissolved gold recovered during rinsing.

Jan 1, 1996

By M. Fiset, D. Belley

"In a country with a cold climate like Canada, the cost of replacing worn parts of snowplow equipment such as blades, is enormous. A great number of these blades, with different mechanical properties, are available, but few studies have been made to facilitate their selection according to the optimum ratio of wear resistance to cost. To attain this objective, laboratory tests have been developed to correlate test results with those obtained from various road service conditions. The test materials, 1080steel in different states, 1090steel and D2 tool steel were chosen to cover a large range of hardness as well as different microstructures. Comparison of the wear resistance of the test materials relative to a standard revealed, in general, a good correlation between the results of laboratory cement wheel tests and those from the road tests. Scanning electron microscope wear scars of laboratory and road test specimens were compared to determine if similar removal material mechanisms were active. IntroductionThe correlation between wear tests in service and those performed with the aid of laboratory equipment is of considerable interest. As a matter of fact, when correlation exists, it allows one to evaluate the performance of a material more easily and at a lesser cost.Several authors have been interested in simulating various wear circumstances, especially abrasive wear. In particular, the simulation of wear on implements working the soil, has been tried by several researchers. The test using the rubber wheel seems to be the one giving the best correlation if the soil is rather sandy and its moisture content is low.However, little work has been done concerning wear on the plates, skids and blades attached to trucks used for levelling and snowplowing; such equipment being used to keep roads clear in northern countries. Now each year, companies introduce new steels by claiming that the y are superior in performance to their predecessor s and invariably they demand a higher cost. The study presented here was undertaken with the goal of making a more judicious choice of these steels by simulating their behaviour in the laboratory. Moreover, the examination of abraded surfaces in situ and in the laboratory have also allowed us to compare the respective wear mechanisms."

Jan 1, 1988