Search Documents

By Randall E. Hughes, John F. Burst

This chapter describes the nature and occurrence of the principal clay minerals that are used as ceramic raw materials, explains how these raw materials are used to produce finished goods, and summarizes positive and negative trends that will affect future demand for raw materials and products in the ceramic industry. The term ceramics was derived from the ancient Greek keramikos (a clay jar). A ceramic product is a material that has been fired to at least 468.3°C (Mitchell, 1983). In addition to being one of our earliest manufacturing and construction materials, ceramic products are among the earliest records of civilization. The enduring significance of ceramics is shown by the fact that, even today, the manufacture of whitewares, brick and related red-fired wares, refractories, and engineered ceramics continues to be a major sector of the US economy. A wide range of materials can be made into ceramic products, although relatively few earth materials make up most of the ceramics in today's markets (Table 1). Most ceramic products are made from clay or a related material. The long history of clay use in the ceramics industry stems from its variable and sometimes unique physical and chemical properties, as well as its ubiquitous occurrence and relatively low cost. Clay is important to ceramics because of its plasticity, moldability and filterability, chemical content, color. refractoriness, solubility. corrosion resistance, electrical properties, and other properties that result from the essentially two dimensional morphology of the individual clay mineral platelets. Because of their basic relationships to the chemical and physical properties of clays, the chemical and mineralogical content have been the subject of continuous studies over the past few decades. Advances in knowledge about the chemical, mineralogical, and physical properties of clays are responsible for most of the advances in processing. The need to remove off-colored contaminants, minerals with low melting points, and soluble salts has resulted in beneficiation by wet processing methods such as water washing. Water washing is restricted to kaolins, although low cost methods of water washing have been extended more recently to ball clays in Europe. High intensity magnetic filtration and flotation technologies have noticeably improved the quality of kaolins and broadly expanded their use in the ceramics industry. In addition to products for construction (e.g., brick, tile, sewer pipe, field drain pipe, cement, fiberglass, roof granules, and paint) and manufacturing (e.g., refractories, kiln furniture, sanitary ware, pottery, and dinnerware), clays are used in calcined form as ceramic fillers, carriers, extenders, and grogs. Ceramics suppliers are under economic pressure in several of these product areas. Manufacture of refractories in America has declined as steel production has decreased. Similarly, dinnerware and tile production have declined because of foreign competition. Fortunately, new uses for clays,

Jan 1, 1994

By Harlan L. Kebel

Gypsum, the dihydrate form of calcium sulfate, has a history of usefulness to man dating back several thousand years, and a worldwide industry has been built on the mining and processing of this versatile industrial mineral. However, anhydrite, the other prin¬cipal calcium sulfate mineral, has very limited use, so much so that separate statistics for it are not always kept, but are usually included with those for gypsum. Although often found in close association, the two minerals have important chemical differences in that anhydrite is the anhy¬drous form of calcium sulfate (CaSO4) whereas gypsum is the dihydrate (CaSo4.2H20). These two molecules of combined water result in significant differences in hardness, density, and solubility of the two minerals. Of most importance, however, is the difference in thermal properties wherein gypsum, upon the application of a modest amount of heat, can be converted to the hemihydrate of calcium sulfate (CaSO4 '21H20) or plaster of paris, an intermediate product upon which is based over 90% of the value of all calcium sulfate end products. Anhydrite, on the other hand, is inert at these temperatures and its uses have been limited to only those few cases where calcium sulfate in the anhydrous form may have an advan¬tage. The earliest known use of gypsum plaster dates back some 5000 years to the time of the Pharaohs of Egypt who had discovered that gypsum rock, when exposed to fire, broke down into a powder which, when mixed with water, would form a putty that could be plastered on a rough mud brick or stone wall to make a smooth finish. It was used down through the centuries in a limited way for ornamental purposes, but did not achieve wide acceptance because of the quick (25 to 30 min) setting or hardening time which made it difficult to use. The first real understanding of gypsum chemistry was developed in France about 1755, and the gradual growth of its present utilization dates from that time. In the United States, the first utilization of gypsum was to grind it to a fine material for use as a soil conditioner at about the time of the Revolutionary War, and the term land plaster for ground gypsum was coined and has remained in use. Another cementitious material-lime or calcium oxide-had become the usual plastering material, but by about 1870 a method for retarding the set of gypsum plaster was discovered; today it has almost completely replaced lime as a plastering material. In recent years, gypsum products sold in the United States have reached a total valuation of approximately $2 Gpy as illustrated in [Table 1].

Jan 1, 1994

By Bruce H. Mason

Lightweight aggregates are classified as those minerals, natural rock materials, rock-like products, and byproducts of manufacturing processes that are used as bulk fillers in lightweight structural concrete, concrete building blocks, precast structural units, road surfacing materials, plaster aggregates, and insulating fill. Other uses include architectural wall covers, suspended ceilings, soil conditioners, and other agricultural uses (Mason, 1989). One unusual agricultural use recently reported was for bedding on a crocodile farm on the south coast of Natal. It seems that female crocodiles became upset because there was no vermiculite in which to lay their eggs due to the late arrival of a consignment of vermiculite. The vermiculite was being used as a substitute for river sand to nest crocodile eggs (Griffiths, 1989). The various lightweight aggregate materials may be classified into four groups as follows: 1. Natural Lightweight Aggregate Materials-prepared by crushing and sizing natural rock materials, such as pumice, scoria, tuff, breccia, and volcanic cinders. 2. Manufactured Structural Lightweight Aggregates-prepared by pyroprocessing shale, clay, or slate in rotary kilns or on traveling grate sintering machines. 3. Byproduct Lightweight Aggregates-prepared by crushing and sizing foamed and granulated slag, cinders, and coke breeze. This group of lightweight materials, with the exception of slag, has become less significant and will not be discussed in this chapter. Other lightweight aggregates are beginning to appear in the marketplace. Some are the result of manufacturing processes on industrial byproducts and/or waste products, such as fly ash and incinerator residue (Bigner, 1992). 4. Manufactured Insulating Ultralightweight Aggregates-pre- pared by pyroprocessing ground vermiculite, perlite, and diatomite. The application of diatomite in brick and in extruded and aggregate forms has declined in recent years (Kadey, 1983) and will not be considered in this chapter. Lightweight aggregates for structural concrete and concrete masonry units, according to the American Society for Testing and Materials (1986) consist of "aggregates of low density used to produce lightweight concrete, including: pumice, scoria, volcanic cinders, tuff and diatomite; expanded shale, clay, slate, perlite, vermiculite or slag; and end products of coal or coal combustion" (Mason, 1989). Lightweight aggregates are distinguished from other mineral aggregate materials by their lighter unit weights-1 281 to 1 602 kg/m3 or less for loosely packed lightweight aggregates-as com- pared to 2 002 kg/m3 or more for crushed stone, sand, gravel, air-cooled slag, and other common mineral aggregates. The specific gravities of these lightweight aggregates are also used to classify them for use in concrete; they range from the extremely light materials, used for insulative and non-structural concrete to expanded shale, clay, slate, and slags used for structural concrete. Vermiculite and perlite are sometimes referred to as super light- weights. Insulating concrete (non-load bearing) weighing as little as 240 kg/m3 can be made with these aggregates. Natural aggregates such as pumice, pumicite, and scoria are normally made into concrete weighing about 400 to 480 kg/m3. Expanded shale, clay, and slate produced in a rotary kiln make structural concrete ranging from 1 201 to 1 842 kg/m3. Expanded shale and clay produced by sintering make concrete that ranges from 1 442 to 1 922 kg/m3. Air-cooled slag produces concrete ranging from 2 162 to 2 403 kg/m3. The low density lightweight aggregates are used primarily for insulating purposes. They have relatively low compressive strength. The middle density aggregates are used for insulation and for fill. Those at the upper end develop excellent compressive strength and are used in many structural applications (Anon., 1971). In recent years, the production of lightweight aggregates in the United States for all uses (including insulation and construction materials) has averaged about 19 Mtpy (Table 1). The production and consumption of lightweight aggregate is closely tied to the fortunes of the construction industry and the need to construct energy efficient buildings. Recent years have seen the production of lightweight aggregate approach the levels of the early 1970s. The period of 1979 to 1981 was a low point in production levels. The low levels of production were caused by significantly higher plant energy costs due to the large amounts of fuel and energy used in the production of most types of lightweight aggregate. Lower levels of construction activity also affect production levels. This chapter focuses on the use of natural lightweight aggregates and manufactured insulating ultralightweight aggregates, and on both the production and use of manufactured structural light- weight aggregates. Some additional comments are made on byproduct materials. Separate commodity chapters on vermiculite, perlite, pumice, and volcanic cinders are elsewhere in the volume. Discussion of the commodities covered elsewhere in the book will be limited to observations on their utilization and relation to other lightweight aggregate materials.

Jan 1, 1994

By Erhard M. Winkler

The rapid decay and disfiguring of stone monuments in urban and desert rural areas has challenged conservators to protect stone surfaces from premature decay. They attempt to halt the natural process of stone decay and possibly to restore the original strength lost mostly by chemical weathering and the loss of binding cement. Ageneral solution is not possible because the physical and chemical characteristics must be considered for different stone types. The failures of stone preservation and restoration are greater in number than the cures. The need for repair of stone decay goes back to evidence of Roman replacement of decaying stone. The presence of excess water in buildings has long been recognized. Moisture tends to enter masonry from air in humid climates, a most important but often underrated factor (Fig. 1) suggesting that sealing should be the answer. Undesirable staining and efflorescence result in accelerated scaling. Today, the great variety of chemicals available to the modem conservator for sealing. consolidating, or hardening stone fall into two very different categories: surface sealers and penetrating stone consolidants, or a combination of both. SEALERS Sealers develop a tight, impervious skin which prevents access of moisture. Surface sealing has saved monuments from decay by eliminating the access of atmospheric humidity. Pressure tends to develop behind the stone surface by moisture escape. Efflorescence, crystal growth action, and freezing can cause considerable spalling (Anderegg, 1949). Flaking results when moisture is trapped behind the sealed surface. Yellowing and blotchiness are also frequently observed. The following sealants are in common use today: linseed oil, paraffin, silicone, urethane, acrylate, and animal blood on stone and adobe. Extensive cracking and yellowing has resulted soon after application. In the past many such treatments have created more problems than cures: 1. Linseed oil and paraffin have been in use for centuries. Embrittlement and yellowing occur rapidly because these are readily attacked by solar ultraviolet radiation. 2. Animal blood as paint has temporarily waterproofed adobe mud and stone masonry. The origin of blood paint has a religious background rooted in the Phoenician and Hebrew cultures. Instant water soluble dried blood can substitute for fresh blood. Winkler (1956) described the history and technique of the use of blood. 3. Silicones have proven very effective and are long lasting. In contrast, acrylates, urethane, and styrene are generally rapidly attacked by UV radiation (Clark et al., 1975). Sealing of Different Rock Types Granitic rocks have a natural porosity traced to 4.5% contraction of quartz, during cooling of the parent magma, compared with only 2% contraction of all other minerals; protection against the hygric forces may require waterproofing of granite in some in- stances. The Egyptian granite obelisk in London is an example. Soon after its relocation from Egypt to London, Cleopatra's Needle was treated, in 1879, with a mixture of Damar resin and wax dissolved in clear petroleum spirit; surface scaling became evident after half a year of exposure to the humid London atmosphere. The treatment of the ancient granite monument from Egypt has denied access of high relative humidity (RH) in London to the trapped salts inherited from the Egyptian desert and has protected the monument from decay (Burgess and Schaffer, 1952). The sister obelisk set up in Central Park, New York City, has fared less favorably because similar treatment was done too late, only after the salts hydrated and hundreds of kilograms of scalings disfigured the obelisk surface (Winkler, 1980). Surface coating of other common stones may be needed. Crystalline marble absorbs moisture from high RH atmospheres: dilation may ensue when curtain panels bow as the moisture starts to expand during daily heating-cooling cycles. A good sealer may prevent the moisture influx provided that no moisture can enter from the inside of the building. Limestones, dolomites and all carbonate rocks are subject to dissolution attack by rainwater, especially in areas where acid rain prevails (Fig. 2). The interaction of sulfates in the atmosphere with the stone can be halted by waterproofing to avoid the formation of soft and more soluble gypsum. The stone surface attack can be diminished if nearly insoluble Ca-sulfite crusts can form, instead of Ca-sulfate. Replacement of fluorite or barium compounds at the stone surface acts as a hardener, rather than a sealant. Sandstones have generally high porosity and rapid water travel can occur along unexpected routes and from any direction. Any surface sealing may do more damage by scaling and bursting than if the stone is left without treatment. Sealing of sandstones is therefore not advised at any time. Testing the efficiency of sealants: Several authors discuss waterproofing materials, silicones, urethanes, acrylates and stearates, as to their water absorption, spreading rates of water on the treated surface, water vapor transmission, resistance to efflorescence, and general appearance (Clark et al., 1975). De Castro (1983) measured the angle of contact of a microdrop (0.004 cm3) on a stone surface as characteristic of the wettability. Laboratory tests and limited field performance are described by Heiman (1981). The crest of a Gothic sandstone arch, which was sealed with silicone,

Jan 1, 1994

By George S. Austin

Mud is one of the oldest building materials used by man, but it is not only of historic interest. Even today in many parts of the world, particularly lightly forested areas, it is the chief building material. Many authorities believe that at least 30% and perhaps 50% of the world's present population lives in earthen dwellings (Dethier, 1985, Coffman et al., 1990). Not all of these people are members of primitive societies or live in third world countries. European, African, Asian, and both North and South American countries contain a large number of such structures. In the United States, the American West, and particularly the Southwest, is known for this type of construction. Some of the earliest remains of adobe structures are those discovered in the ruins of Neolithic farming villages in Mesopo¬tamia dating as far back as 7000 BC (Steen, 1972). The word adobe has its roots in Egyptian hieroglyphs denoting brick and evolved to its present form through Arabic and Spanish (Lumpkins, 1977). The Spanish conquest of the New World spread the use of wooden molds to produce a standard adobe brick. Today, the word adobe is used to describe various earth building materials and techniques, usually referring to sun-dried adobe brick now used in the United States, but is also applied to puddled adobe structures, mud-plastered logs or branches (Jacal or waddle-and-daub), pressed-earth blocks, and rammed-earth walls or pisé (Smith and Austin, 1989, Ferm, 1985). Modern mud construction is used in many countries in various parts of the world. In the United States, the states from Texas to California are perhaps best known for this type of construction. Of these states, New Mexico has the dominant reputation for adobe use. Indeed, in New Mexico the Santa Fe style (Fig. 1) has made adobe not only acceptable, but preferred. RAW MATERIALS Adobe soil used by present day adobe producers, and probably past adobe producers as well, is principally sandy loam (50% clay and silt), although clayey silts are used in some areas (Coffman et al., 1990). In New Mexico, the best adobe soils are those developed on stream deposits, particularly Holocene (Recent) terrace deposits and older, loosely compacted geologic formations, such as the Santa Fe Group (Tertiary) located in the Rio Grande Valley. Some modern adobe producers use a mixture of materials from the screened fines of aggregate operations and mud from irrigation ditches in the river valleys combined with varying amounts of sand to produce the proper blend. Mineralogy Bulk Mineralogy: X-ray diffraction analyses of whole rock samples from many parts of the world where adobe is the dominant construction material show the major constituents of adobe are quartz and feldspar, with lesser amounts (in order of abundance) of calcite, clay minerals, and gypsum (Coffman et al., 1990). Adobes from and climates contain considerable calcite; in some cases calcite is second only to quartz in volume. Quartz, feldspar, most of the clay minerals, and some calcite commonly are derived from the mechanical/chemical breakdown of older rocks units. Some of the clay minerals, much of the calcite and perhaps all of the gypsum are precipitated from evaporating water. Clay Mineralogy: Clay-size minerals consist dominantly of clay minerals, but nearly clay-size fractions contain minor amounts of quartz and calcite, and occasionally other nonclay minerals. In earth construction materials from New Mexico, clay-size particles are the most compositionally variable in commercial adobe soils. However, the clay mineral groups in this size fraction consist of about equal parts of expandable clay minerals (smectite and mixed¬layer illite/smectite or I/S) and non-expandable clay minerals (ka¬olinite, illite, and chlorite), with minor quartz, calcite, and feldspar (Smith and Austin, 1989, Austin, 1990). In the and American Southwest, smectite is commonly calcium-rich and the I/S is dis¬organized and randomly interstratified. In a study of 42 New Mex¬ican commercial adobe soils, only two contained chlorite, and vermiculite, sepiolite, and palygorskite were not found. Soils in temperate climates, as are found in the midwestern and northeastern United States, contain an abundance of illite (Potter et al., 1975). The clay minerals in earthen structures of that region and in Europe commonly contain illite with less amounts of kaolinite, smectite, I/S, chlorite, and vermiculite. In contrast, the clay-size fractions of soils of humid tropical areas are typically acid, with kaolinite as the dominant clay mineral and lesser amounts of I/S, illite, smectite, and others (Chamley, 1989).

Jan 1, 1994

By Rustu S. Kalyoncu

Rainbow colors of roofing granules, adorning the roofs of buildings from single family units to largest office buildings, have their origin in the roofing shingles as burlap soaked with tar appearing as early as the 1700s. Dusting of talc and mica on the coated surfaces, to keep roofing from sticking to itself in storage, represents an early improvement to the original construction product. Sometimes, colored, natural mineral dusts were added as color pigments within the dusting material, for initial color. Prolonged exposure to sun caused the asphalt to become brittle, and it eventually cracked and leaked. Search for solutions to cracking and subsequent leaking problems eventually led to the use of crushed mineral granules on asphalt coated shingles. This provided the impetus for further growth in the asphalt roofing industry. Application of a layer of crushed mineral on the asphalt coating minimized the coating deterioration from exposure to ultraviolet light, thus significantly improving the shingle life. In the 1900s, screened waste from slate quarries was the most commonly used granule in asphalt roofing products. Records indicate the use of coarse slate screenings for asphalt roofing as early as 1906. As the asphalt roofing industry further developed, other naturally colored minerals, such as silica sand, quartz, mica, feldspar, talc, slag, granite, rhyolite, and oyster shells were used on roofing surfaces. Later on, a number of manufactured granular materials, such as crushed brick and tile, fire clay, and white porcelain were used. The first artificially colored roofing granule was produced in 1914 by running molten slag into a solution of alkaline metal silicate, which was absorbed by the porous slag. Various colors were obtained by adding pigments to the silicate coating and by subsequently heat treating the granules. In 1922, another technique was developed in which green slate granules were saturated with copper sulfate solution and heated to 760°C to form copper oxide. Since then, many other granule coloring processes have been patented, one of the most significant being the sodium silicate coatings introduced around 1975. Granules as used in construction (specifically roofing materials) are defined as natural or synthetic-mineral grains smaller than gravel and larger than sand in particle size. They are used primarily for protective and decorative purposes on the weather- exposed surface of asphalt composition roofing. Development of artificial coloring techniques has made it possible for the roofing industry to provide asphalt roofing shingles in a wide variety of colors complementing the color and style of buildings. Roofing granules, as we see today, are the products of long technological evolution.

Jan 1, 1994

By James M. Barker, George S. Austin

Stone, one of the oldest building materials, today remains a well-established material throughout the construction industry. The use of natural stone is much less prevalent now than in the past. It is still widely considered to be the most aesthetically pleasing, prestigious, and durable building material. New and re-opened quarries are coming onstream to meet increased demand related to new building technology and increased residential use of stone. CLASSIFICATION No classification can completely eliminate overlap between dimension stone, aggregate, and decorative stone because most stone is multi-purpose. Many used for decorative purposes are not produced specifically for that end use. Rock otherwise considered waste in dimension stone or aggregate quarries can be decorative stone coproducts (Fig. 1). Many uses require a compromise between decorative and structural qualities (Bowles, 1992, written commu¬nication). Shipley (1945) used decorative stone interchangeably with or¬namental stone. Gary et al. (1972) defined decorative stone as that used for architectural decoration, such as mantels, columns, and store fronts, but added that it is sometimes set with silver or gold in jewelry as curio stones. Bates and Jackson (1987) also restricted decorative stone to that used for architectural decoration. Meanings of otherwise identical terms used in the stone industry differ be¬tween geologists, engineers, and quarriers. They often carry a much broader meaning for quarriers and engineers compared to their very specific use by geologists (Makens et al., 1972). Decorative stone, including ornamental stone, is more broadly defined by geologists as any stone used primarily for its color, texture, and general appearance. It is not used primarily for its strength or durability, such as construction stone, or in specific sizes, such as dimension stone. The decorative stone industry uses a much wider range of stone types compared to stone that is dimensioned. Decorative stone usually serves some structural pur¬pose, but is not load-bearing to any great extent. Weak or costly stones serve in decorative, not structural, applications. STATISTICS AND END USES Decorative and dimension stone data are difficult to separate because the US Bureau of Mines keeps statistics only on dimension stone and crushed stone. The value of domestic dimension stone production in 1990, which includes some decorative stone, was about $210 million compared to imports of about $524 million and exports of about $35 million. Production was 1 080 t of which at least one-third was for decorative uses (Taylor, 1992). The principal uses are rough blocks in building construction (23%) and monu¬ments (18%); the remainder is used as ashlar (18%), curbing (12%), and miscellaneous (29%). Major rock types are granite (50%), limestone (30%), sandstone (10%), slate (3%), marble (2%), and other (5%) (Harben, 1990). Crushed stone valued at $5.6 billion was produced in the United States in 1990 by 1700 companies operating 3400 active quarries in 48 states (Tepordei, 1991). About 52% is used in con¬struction, 9% in cement and lime manufacturing, 2% in agricul¬ture, 2% in industrial uses, and 35% for unspecified uses including decorative aggregate. Limestone and dolomite comprise about 71%, granite 14%, and traprock 8% of the stone crushed in the United States. The remaining 7% are, in descending quantity, sandstone, quartzite, miscellaneous rock, marble, shell, calcareous marl, volcanic cinder and scoria, and slate. The basic types of decorative stone are: rough stone, aggregate, cut or dressed stone, and manmade stone [(Table 1)]. Rough Stone Rough stone is used as it is found in nature with very limited processing such as minor hand shaping, edge fitting, and size or quality sorting (Perath, 1992, written communication). This stone type is often marketed locally in relatively small tonnages and includes fieldstone and flagstone. The primary end uses of rough stone are landscaping, edging, paving, or large individual stone landscape or interior accents [(Fig. 2)]. Fieldstone: Fieldstone is picked up or pried out of the ground (gleaned) without extensive quarrying and includes garden or large landscaping boulders (Austin et al., 1990, Hansen, 1969). Boulders and cobbles may be split or roughly trimmed for use in rubble walls and veneers, both interior and exterior. Popular fieldstone rock types include sandstone, basalt, limestone, gneiss, schist, quartzite, and granite, but many others are suitable. Much fieldstone is col¬lected by individuals or small companies because the industry is labor intensive and markets are small. The stone may be sold locally in small quantities from the back of vehicles (Austin et al., 1990). Fieldstone includes many rock types, sizes, and shapes with the only common denominator that it must be set by hand and be durable (Power, 1992, written communication). Moss Rock. Moss rock is fieldstone partially covered by algae, mosses, lichens, and fungi that give the rock an aged and variegated patina (Austin et al., 1990). The plants are supported by moisture and nutrients in the stone. Moss rock is used for landscaping, walls, and fireplaces. Although almost any durable rock can be a moss rock, most are slabby or rounded sandstone and limestone (Fig. 3). Flagstone: Flagstone or flagging consist of thin irregular slabs used for paving, walkways, and wall veneers. Random-shaped flagging is produced widely in the United States. Suitable stone

Jan 1, 1994

By W. A. Green

Introduction While pilot-mill operations were being carried on at Flin Flon, as described by R. E. Phelan (1), a detailed topographic map was being made of the area in the vicinity of the ore-body for later use in laying out plans for the final plant. The area covered by this survey was 6,600 feet by 6,600 feet, with contours on 2-foot intervals. As mentioned by Mr. Phelan, it was definitely decided at the end of November, 1927, to take up the option on the Flin Flon property and to proceed immediately with the plans for construction of a metallurgical plant at Flin Flon to treat 3,000 tons of ore per day, and of a hydro-electric power plant at Island Falls, Saskatchewan, to supply power for the future operations at Flin Flon. Railway Built From The Pas to Flin Flon Just as soon as the decision was made to go ahead with the construction work and opening-up of the property, it was of course essential to give immediate attention to the building of a railway to the mine. Many years previously, a preliminary survey had been made for a railway to branch off the Hudson Bay railway at a point 4.7 miles northeast of The Pas, and, during certain negotiations in 1925, the Provincial Government of Manitoba had agreed to guarantee the railway bonds necessary to finance the building of the line, so that it was possible to organize for this work immediately. A contract was let by the newly organized Manitoba Northern Railway Company to the Dominion Construction Company, Ltd., and Tomlinson, for the building of the railway to the mine, a distance of approximately 87 miles (see Figure 1). The Manitoba Northern railway is a subsidiary to the Canadian National railway, and all engineering and supervision of the contractors was done by the Canadian National engineers. Actual construction work was started in January, 1928. The first 52 miles of the railway from The Pas to Cranberry Portage is over fairly level, although slightly rolling, country, and a considerable portion of the route is over muskeg area. Rails were laid on top of the frozen muskegs. Gravel deposits were opened-up along the line and, before warm weather; sufficient ballast .was distributed in the muskeg areas to prevent thawing under the track, and thus give the necessary support to allow uninterrupted transportation over the line.

Jan 1, 1935

By Kentaro Kuraji

INTRODUCTION Background Tokyo, the capital of Japan, is one of the largest cities of the world. As many as 33 million people live in Tokyo and three neighboring prefectures although the city occupies only 0.6% of the area of the country. The network of Metropolitan Expressways serves as a major artery for daily physical distribution in Tokyo. The Central Circular Route of the Metropolitan Expressway (MECCR) is located innermost among the three circular routes in Tokyo (Figure 1). Once completed, MECCR is expected to drastically mitigate traffic congestion in the central Tokyo area and provide drivers wider varieties of options in route selection. Alleviating congestion is estimated to reduce 400,000 tons of carbon dioxide emissions annually. The eastern and northern sections and part of the western section of MECCR have been completed with the total length reaching 33 km. The western section will be extended southward by approximately 4 km in the spring of 2010. An 11-km-long western section of MECCR that is currently being constructed is composed mostly of tunnels. A large number of power supply, gas supply, telephone, drinking water and sewerage pipes have been placed under the Yamatedori avenue along which MECCR is being constructed. The shield tunneling method has therefore been adopted for constructing tunnels along the route. The method involves the advancement of a shield tunnel boring machine (TBM) through the ground simultaneously assembling segmental rings within the shield. The method not only enables the building of highway tunnels more quickly and efficiently than other methods but also minimizes the effects of construction work on the surrounding area and the environment. Constructing the tunnel using the conventional cut-and-cover method might have required large amounts of time and cost because relocating the numerous objects buried under the Yamatedori avenue might have been necessary during tunnel construction. It was also considered desirable to place the tunnel at a depth of 30 m or more from surface to prevent tunnel construction from adversely affecting railways because the tunnel was expected to cross eleven railways and subways. This is one of the reasons for selecting shield tunneling as an effective method. The shield tunneling method was finally adopted for a length of 7 km in the 11-km western section of MECCR. The shield tunneling method was also employed in the Ohashi Tunnel located southernmost in the 11-km western section of MECCR. This paper describes the construction of the Ohashi Shield Tunnel.

By A. Moergeli, Philip Sander, John J. Reilly

"Estimating and managing the costs of complex infrastructure projects – in the planning/design and construction phases, for both owners and contractors – has been a challenge for decades. The more complex and technologically advanced the project, the greater the uncertainty, including potential risks that are important to owners and contractors, such as:• Cost risks to owners – meeting budget and schedule, maintaining public credibility.• Cost risks to contractors – profit, consequences of loss, impacts to reputation/future work.This concern has been addressed in various ways by the underground construction industry for some time (Reilly, 2001). In particular, while significant advances have been made in cost estimating for the planning and design phases (Reilly et al., 2004), that are important to agencies and political decision-makers, it is not apparent that these advances have been widely adopted for construction cost estimates. The reasons for this may relate to lowbid considerations – any method that tends to increase the contractor’s cost estimate, by including risk or likely costs, could lead to an erosion of the contractor’s competitive position – if others are not similarly required to include such costs.Different cost estimating methods produce different levels of information. Specifically, there is a large difference in the character and depth of information if a deterministic (quantities times price plus a contingency) and risk-based cost methods are used. It is this difference in character and depth of information that is the reason that risk-based cost estimating has potential value for owners and contractors. Figure 1 presents hypothetical cost results from deterministic and risk-based methods and illustrates some of these differences.In Fig. 1, the results for deterministic and risk-based cost estimates are given related to the potential profit or loss for a typical project. As is evident in this example, there is significant potential for costs to be realized that are higher than the proposal/bid value estimated using a deterministic approach, with a 15 percent probability of a loss. There is a 30 percent probability that the project will have a reduced profit. There is a 55 percent probability that the project will return a good profit. Using a risk-based approach, it is possible to better recognize this potential outcome in the bid phase and, as a consequence, develop a strategy to:"

Apr 1, 2016

By A. B. Hooker

The flame safety lamp with metal-gauze enclosure was invented by Sir Humphrey Davy more than a century ago, primarily for its safe light; however, it soon became the standard device for detecting the presence of methane in mine atmospheres. It still is the most widely used device for this purpose and is also the most practicable means of detecting deficiency of oxygen in coal mines. A permissible flame safety lamp is similar in all respects to one that, after a series of tests, has been approved by the Bureau of Mines as safe for use in gassy mines. However, safety depends largely upon the way lamps are maintained and used.

Jan 1, 1944

By A. R. Dover

The Richmond-San Rafael Bridge is a 6.92 kilometer (4.3 mile) long major toll bridge span that crosses the northern San Francisco Bay in a highly seismically active region. Tutor-Saliba / Koch / Tidewater JV was contracted by Caltrans to conduct a comprehensive seismic retrofit. The JV provided geotechnical planning and quality control services as described herein, under normal oversight by Caltrans. Part of the robust foundation retrofit design included the installation of 26 new, large diameter piles, including eleven 3.81 m (12.5 ft) diameter, cast-in-drilled-hole (CIDH) marine piles that were drilled 9.15 m (30 ft) into the bedrock beneath the Bay, where the water depth ranged up to about 21.3 m (70 ft). These reinforced concrete-filled composite piles have a steel shell permanent casing from the bridge substructure pile cap through the water column and 30.5 to 39.6 meters (100 ft to 130 ft) of marine sediments to the top of rock. This paper discusses construction, inspection (ranging from the QA employed in the planning of the CIDH pile installation methods and equipment to the actual construction inspection required for the routine installation of the shafts), problems that were encountered during construction, and the solutions that were developed and implemented. Inspection, particularly with the usual difficulties in the marine environment, coupled with the difficult and complex bedrock conditions was particularly challenging, and ranged from non-destructive testing to "in-water, inshell" diver inspection. Similarly, the complexities of dealing with both the steel casing "riser" and the associated drilled shaft (rock socket) portion of these composite foundation elements created some unusual issues. The paper also presents important lessons learned from the project.

Jan 1, 2008

By William M. Camp

Construction-induced earthborn vibrations have long been recognized as a potential problem with respect to the constructed environment and various vibration criteria are in use to prevent damage. A special case of construction vibration control is the protection of early-age or ?green? concrete. Unlike limits for damage prevention to building stock, there is no rational, widely accepted limit for protection of early-age concrete. Numerous criteria have been proposed or reported in the literature and the most relevant and rational proposals are summarized herein. These findings are applied to a case history involving both bored and driven piles. Vibration measurements were made during pile driving activities and the vibration magnitude was evaluated with respect to the exposure of freshly-placed and curing concrete to the earthborn vibrations. The maximum vibration magnitude at the applicable distances from pile driving was on the order of 0.3 inches per second. Based on the most persuasive literature, threshold values of 0.8 inches per second or even 1 to 2 inches per second for the protection of green concrete appear to be well-supported. Consequently, it was concluded that the pile driving activities and bored pile construction could proceed simultaneously.

Jan 1, 2010

By F. Vallianatos

The main objective of the present investigation is to demonstrate the potential of ERT (Electrical Resistivity Tomography) and HVSR (Horizontal to Vertical Spectral Ratio) methods as geophysical tools for the monitoring of subsurface cavities. The survey sites are located in Akrotirion Peninsula, almost 7 km east of Hania town in Crete Island, Greece. At this site, the surface expression of a known cavity with a diameter of about 25 m is visible. The true geometrical characteristics of the cavity were unknown since there are no boreholes in the area. The focus of this survey was primarily of a qualitative nature and the objective was to determine if ERT and HVSR could be used to identify and map near surface cavities (less than 30 meter in depth) in a limestones kartsic area such as Akrotirion Peninsula. A 2D/3D model of the resistivity distribution is given for the area under investigation. Furthermore, analysis of microtremors data provides a profile of the seismic response of the tectono-karstic voids.

Jan 1, 2006

Our merchant marine is rapidly outgrowing our consular service, according to Edward N. Hurley, Chairman of the United States Shipping Board, who urges that steps be taken immediately to provide facilities abroad for handling the millions of tons of shipping which will be afloat under the American flag in peaceful trade when the war is over. When peace is restored and our present tonnage is scattered over world trade routes, the consular service will be inadequate to handle our ships: Besides, it will have to work against the handicaps of obsolete shipping regulations and, in many cases, lack of experience. There are nearly 100 pages in the United States consular regulations dealing with shipping platters. . Many of these regulations are based on old treaties and many of them are obsolete. There are also differences between treaties with various countries. Our consuls often lack authority to handle matters involving the interests of our sailors and shipowners. Before we can operate a modern merchant marine we must revise, standardize, and simplify this whole mass of regulations and bring them up to the efficiency of other nations' practice.

Jan 12, 1918

Mineral resource and ore reserve estimation is a challenging and demanding field, requiring application of professional knowledge, skill and experience of the highest order. If the many potential hazards and pitfalls are to be avoided however, there are two other requirements which are of equal, if not greater importance:

Jan 1, 1990

By Brian FitzPatrick, Michael J. Weaver

Everyone has a role in site safety, even consultants. This paper presents a summary of how a geotechnical and environmental consulting firm, with field staff on construction and subsurface explorations sites, engaged their staff and leveraged relationships with contractors to assess the construction related risks to which its staff members are exposed. These findings were then integrated into their technical training materials for both new staff and those needing a refresher, so that safety is discussed at the same time as the technical work and not treated as a separate topic. The paper outlines the process of identifying and evaluating the construction related risks that staff members face and presents examples of how the consultant can engage contractors in the process. By doing this, knowledge can be shared and there is a better mutual understanding of the risks associated with common construction and exploration related field tasks. The work resulted in an increase in staff engagement in safety, a better understanding of the true risks that staff face in the field, better relationships with contractors, and lower safety metrics. HISTORY At Haley & Aldrich, Inc., we renewed our safety journey in May 2012. Like many others, we had concerns over injuries our staff experienced in the three previous years, and a potentially significant utility strike we experienced while excavating a trench. In 2009, 2010 and 2011 we experienced an increase in recordable injuries, including two significant injuries, which caused our Experience Modification Rate (EMR) (see note below), Total Recordable Incident Rate (TRIR), and Days Away-Restricted, and Transferred Rate (DART) to rise significantly. See Fig. 1 for details. This caused us to step back and review our approach to safety, and our “safety culture”. The rise in reportable incidents and injuries also corresponded to the beginning of a growth period for the company.

Jan 1, 2019

By C N. Whata

While there is no specific obligation on the part of any applicant to consult directly with tangata whenua (people of the land), recent cases highlight the need to engage in active consultation in order to avoid serious objections and delay, particularly where a proposal may affect the matters referred to in section 6(e) (Waahi tapu/sacred places) and 7(a) (KaitiakitangaiGuardianship) of the RMA.   The Environment Court has shown some sympathy for tangata whenua where waahi tapu and other significant matters of cultural concern are at risk because of a proposed development. There are several practical steps that can be taken to minimise the potential for serious objection including: ò knowing who to contact and how to contact them; ò demonstrating empathy for the concerns of tangata whenua; ò engaging in proactive consultation, for example meeting at a time and a place that is suitable to tangata whenua, and a preparedness to meet the costs of tangata whenua etc; ò demonstrate an awareness of tangata whenua issues; being aware of the types of mechanisms that are available to remedy, avoid etc adverse effects on matters of concern to tangata whenua.

Jan 1, 1997

By G. Gregory Bryan

G. GREGORY BRYAN 33.1-DEFINITIONS 1. Engineering-Engineering may be defined simply as the science and art of making materials and energy serve the purposes of mankind. There are many fields of engineering, each with specialized branches. The basic fields are: civil, mechanical, electrical and chemical. Others may be specialized phases of one of these or a combination of two or more of them. Mining engineering, for example, requires a working knowledge of construction, mechanics, electricity, metallurgy, geology, accounting and economics, in addition to mining techniques or methods. Mining geology and geological engineering involve rocks and their structure and the forces that act upon them, and chemistry, physics and mechanics also are important to practitioners in these fields. Metallurgical engineering requires chemistry and physics but also a working knowledge of mechanics and electricity. The fields of engineering with which this section are concerned are those primarily involved in the finding, mining, processing and utilization of the natural mineral resources of the earth. They include geology, mining engineering and metallurgy, each with several specialized subdivisions. 2. The Engineer-The engineer is an individual who has had specialized training to qualify him to practice the profession of engineering. The term engineer is used here in its broadest sense to include such professions as certain applied branches of geology, physics and chemistry, whose practitioners may not have acquired engineering degrees but who, nevertheless, by training and experience in some area of the minerals industry, qualify under the above definition. To become a successful engineer, a person should have certain pronounced aptitudes and preferences, even before embarking upon the requisite course of training. Among the chief qualifications that the engineer-to-he must possess are: (a) a natural inclination toward mathematics and the physical sciences, and (b) intellectual and moral honesty. Among the qualities the student engineer must develop are: (a) independence of thought, open-mindedness, sound judgment and the ability to observe, deduce, plan and apply solutions, (b) the ability to articulate and convince, and (c) the ability to organize and direct the activity of others. These qualities are normally developed through sound education, followed by pro¬gressive experience. 3. The Consulting Engineer-The consulting engineer is an engineer primarily in the business of furnishing specialized advice and engineering services on an intermit¬tent, part-time or occasional basis to clients who do not have continuous or full-time need for those services. He must be able to make and take full responsibility for decisions and recom¬mendations where original thought is required. He should not be confused with the engineer, surveyor or technician who also may furnish services on an intermittent basis, such as regular periodic surveys, the overseeing of drilling programs and other such routine work as may require little original thought and planning. 33.2-THE PROFESSION OF CONSULTING ENGINEERING 33.2.1- QUALITIES REQUIRED A successful consulting engineer must first have, as a minimum, the qualities and preparation of an engineer. In addition, he must have sufficient knowledge,

Jan 1, 1973

Alabama.1 Arizona 1 Arkansas 2 California 2 Colorado 7 Connecticut 8 Delaware 9 District of Columbia 9 Florida 10 Georgia 11 Idaho 11 Illinois 11 Indiana 13 Iowa 14 Kansas 14 Kentucky 14 Louisiana 15 Maine 16 Maryland 16

Jan 1, 1952