Search Documents

By N. Wahl, D. M. Blackketter, R. Thornton

This paper evaluated using a water-filled abandoned mine (Orphan Boy) as a heat source for a 240- kW closed-loop heat pump with the goal of heating a 2,000-m2 building. The mine has a 245-m vertical shaft connected to a large stope by three horizontal cross-cut shafts. There is 1,250 x 106 L of water at a consistent temperature of 24-26° C that is available mostly in the stope. The only heat exchanger placement option is in the vertical shaft. Therefore, the focus was to model heat exchanger placement in the vertical shaft to determine the extent to which the systems will induce thermal currents between the stope and vertical shaft. Modeling of thermal currents, temperature profiles and heat contribution from the ground was done using finite difference and computational fluid dynamics. An optimal configuration was determined showing sufficient water movement and heat transfer will occur with a low water temperature in the shaft above 20° C. This project supports a U.S. Department of Energy (DOE) grant that will implement the full-scale system.

Jan 1, 2013

By R. Schaller, Ch. Karcher, A. Thess

"Electron beam evaporation of liquid metals is an innovative technology increasingly used in industry to produce very thin coatings of high purity. In this process the surface of a metal ingot, placed in a water-cooled copper crucible, is heated by bombarding it with a high-energy electron beam gun. The material melts, forming a free surface and eventually starting to evaporate. The rising vapor cloud condensates as a thin film on a moving substrate. The strong energy input at the free surface gives rise to vigorous thermos capillary and buoyancy driven convective motion within the melt, leading to unwelcome heat losses. This paper aims to show how these losses can be reduced by optimizing the geometry of the crucible and by using external magnetic fields. We present both experimental and numerical results.IntroductionElectron beam evaporation of liquid metals [l] is an innovative PVD-technology which is excellently suited for the industrial production of high-quality coatings. In this vacuum process a high-energy electron beam heats up the surface of a metal ingot. The ingot melts and forms a free surface. A schematic view of the arrangement is shown in Figure 1. When the temperature of the free surface exceeds the actual (pressure-dependent) saturation temperature of the ambient gas, the liquid starts to vaporize. The rising vapor cloud finally condensates on a moving substrate located at some distance above. To guarantee a superior quality of the coating the melt is typically confined in a water-cooled copper crucible. The intensive cooling is necessary to avoid chemical reactions between the melt and the crucible walls, that is, crucible materials and their reaction products are practically excluded from evaporation."

Jan 1, 1999

By Gruenewaldt von

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. The principles of shear-driven aggregation of particulate matter suspended in fluids, a common industrial method of concentration and separation, were applied to a convecting magma to estimate the time required to sparge or strip the PGE and Cr content and concentrate it into the boundary layers. It was calculated that an ore-grade (e.g. 6 ppm PGE) boundary layer about 1 m thick would require 100 000 years at most to form from a body of magma 500 m deep with a PGE content of 20 ppb. Since concentration would be most vigorous when the magma was warmest, at least half of this concentration would take place in the first 10 000 years. The effect of dispersive pressure in the boundary layer would generate a concentration high of refractories just below the top of each boundary layer and another just above the bottom. If the magma was a double-diffusive system, it might evolve by the downward cascade of enriched boundary-layer material into the hotter, lower magma layers, where depending on saturation levels chromites would equilibrate and sulphides undergo partial or total resorption, enriching PGE levels in any remaining sulphides. This cascade process would in time greatly enrich the lower regions in PGE-bearing sulphides and chromites

Apr 1, 1994

By Frank Hagar, George M. L. Robinson

INTRODUCTION Mine waste monitoring and management is essential when the industry is being required to accept the environmental liability for all generated, stored and disposed solid and hazardous waste. Environmental regulations mandate the operator to minimize waste production while requiring the operator to cleanup existing contamination. Since these requirements are being enforced, many operators do not have a clear under- standing, whether their existing operation will or could be required to adopt remedial plans to mitigate off-site contamination impacts. The following methods, using conventional and advanced geostatistical methods, provide a tool to make appropriate assessments whether existing or potential contaminant issues are present. BACKGROUND Generated solid wastes from mining operations are currently exempt from Solid Waste Disposal Act (SWDA) Sub- title C (RCRA), statutes and promulgated regulations, however, compliance with SWDA Subtitle D statutes and regulations is required. In order for the mining operator to be exempt from hazardous waste regulations, the operator must demonstrate that generated waste does not have hazardous waste characteristics. In many instances the operator will be able to use statistical tools and their existing data to determine whether their site could be a potential hazardous waste liability. METHODS The following statistical and geostatistical methods can be used to determine whether existing wastes could be a regulatory concern. The following presents a brief discussion of standard statistical methods and discusses, in greater detail, how advanced geostatistical tools can be used to define potential waste issues. The following will discuss how data can be screened, "Data Filtering and Reporting"; how data can be evaluated using "Conventional Statistics"; followed by a detailed discussion o f "Geostatistical and Estimation Techniques" and "Statistical Modeling". Data Filtering and Reporting Data filtering is the simplest, but potentially the most powerful statistical tool because data can be easily sorted to meet regulatory reporting requirements. Filtering includes unions and intersections of data such as date, maximum and minimum values of one or several variables. Using the data base presented in "Mine Waste Data Base Management Procedures", Robinson and Hagar, 1987, an example of a filter group is presented.

Jan 1, 1987

By Heinz Brandl

Box-shaped pile and diaphragm wall foundations have proved suitable for transferring heavy loads of bridges, power plants, tanks, towers or other buildings in a concentrated form into the ground. The bearing-deformation behaviour and the earthquake resistance of such "box-foundations" are superior to those of conventional pile groups. The reason lies in the reduction of lateral soil displacement and in the composite effect between concrete elements and the enclosed soil. The paper describes results of comprehensive model tests and in situ measurements, theoretical aspects and case histories.

Jan 1, 2002

By Charles Berry

Conventional and nonconventional insurance is examined from the point of view of a financier of a major mining and minerals project. The paper reviews the elements of a conventional insurance program; explains why such a program is not fully responsive to the project financier's needs; examines some of the new insurance coverages that can supplement a traditional program; and emphasises that these insurance markets are still in the early stages of their development with consequent effects on capacity (insured amount) and to some extent price (insurance premium).

Jan 1, 1985

By B Walsh, M Cattani, S Verpaele

With the increasing sophistication of real-time sampling devices for occupational hygiene exposure assessment, research to objectively assess their performance is a priority. Using real-time monitoring equipment has several advantages over established gravimetric sampling methods, particularly their immediate results, lower overall long-term costs and no laboratory analysis costs, which are appealing to the mining industry due to the ongoing occupational hygiene monitoring programs required by the various regulatory agencies.

Apr 16, 2024

By Marco Aurelio Piangatelli, Massimiliano Bringiotti, Ferdinando De Angelis

"The construction of the three connecting tunnels between the east side and the west side of station C13, adjacent to the Vistula river, has a long and complex history, as they cross beneath one of Warsaw’s main road arteries (Wislostrada). After the attempt to excavate the first tunnel, the face of the tunnel collapsed on the night of August 13, 2012, and a volume of about 10,000 cubic meters of liquid mass (water, silty soil and sand) entered and flooded the west side of the station, which was filled with more than seven meters of material. Fortunately, the workers managed to escape, but machines and equipment were lost. This is the story of how the tunnels were completed, by adopting soil improvement, jet grouting, GRP bars, ground freezing and a careful choice of work steps. INTRODUCTION The Centrum Nauki Kopernik station on Line II of the Warsaw Underground is located alongside to the Vistula river (Figure 1). This station hereinafter is referred to as station C13.The station consist of three parts: the east and west part, and three connecting tunnels 40 meters in length with a large cross section (170 m2).. It includes the rails along the sides and the platform along the centre. The reason for the underground connection of two shafts with a tunnel is due to the presence of a road tunnel (Wislostrada, hereinafter called WS), which must be underpassed by the new metro line (Figure 2).The existing tunnel (Wislostrada) was built many years before, between diaphragm walls, and some foundation structures interfere with the underground tunnel. The challenge was to build the connectors without stopping the traffic of vehicles along the highway above. All works took place in very difficult geological and groundwater conditions due to the presence of Vistula alluvial deposits with poor mechanical characteristics. The soil profile consists of relatively loose sands on top, and silts overlying high plasticity Pliocene clays highly disturbed by the effects of the repeated over-sliding of glacial moraine deposits."

Jan 1, 2016

By Kexin Cai, Isidro Rivera, Shawna Von Stockhausen, Maria Chastka, Kevin Huynh

The Newell Creek Dam Inlet/Outlet Replacement Project is located approximately 11 miles north of Santa Cruz, California along Highway 9 in the San Lorenzo Valley. This project will replace the existing inlet/outlet works at the Loch Lomond Reservoir by constructing a tunnel using conventional excavation methods while simultaneously drilling three intake shafts to intercept the tunnel from within the city’s water supply. This project will improve the system’s overall operational efficiency and performance, and provide a safe and reliable facility for the City of Santa Cruz’s drinking water supply. This paper discusses the overall project configuration, construction observations, and challenges during construction, including tunnel excavating through the marine sedimentary siltstone of the Monterey Formation, probing and pre-excavation grouting, and the tools utilized to manage the project.

Dec 1, 2022

By C. William Parisi

Since the introduction of mechanical mining, some 35 years ago, a great deal of effort has been expended by the coal industry to solve the coal dust problem. The original concern was the possibility of a dust explosion or the propagation of a gas ignition; however, in recent years it has come to be recognized as a possible 'health hazard as well. In the middle thirties, the Pittsburgh Coal Company began an intensive study of the dust problem to determine the dust levels created by the various cycles of operation in mechanical mining and to make a comparison with those of hand loading operations. Numerous dust samples were collected with a midget impinger and it was found that dust counts varied from 38 to 268 million particles per cubic foot during hand loading and from 96 to 227 million particles per cubic foot during mechanical loading. The study indicated that the source of underground dust in coal mining could be classified as primary or secondary. A primary source is one associated with appreciable degradation of size, that is, where most of the fines capable of becoming air-borne are produced. A secondary source is one in which most of the fines have been produced at some previous operation and are in such condition that they can become air-borne. Cutting, drilling and blasting are the operations which produce the primary dust. Secondary dust is formed by operations which include; loading, transportation and discharge at transfer points. The study showed clearly that the coal cutting operation was responsible for the greatest amount of dust and that the amount of dust produced varied directly with the speed of cutting; type and dullness of cutting bits; and the distance the cuttings had to fall to the floor. The information obtained from the study enabled our company to decide on a course of action and the direction to follow. With the cooperation of mining machine manufacturers, water tanks with a 200 gallon capacity were built into the machine trucks and were provided with a pump driven by a small motor. A length of 1/2" water hose carried the water from the pump to the two water spray nozzles located at the front of the machine. Water was delivered to the machine tanks by water cars which were filled on the surface or from an underground water supply. It was during these early days that wetting agents were introduced into the water system. Our studies revealed that wetting agents did little better than plain water in the abatement of the dust problem. It was found that when using a wetting agent less water was required to obtain the same results but we could not take advantage of this fact because it was almost impossible to keep the smaller nozzles open to reduce the amount of water being used.

Jan 1, 1967

The Electricity Commission of New South Wales operates three power stations located on Lake Macquarie and Lake Munmorah. Coal for these power stations is supplied by three collieries operated by the Electricity Commission, three operated by the State Mines Control Authorityrand one privately owned. Most of the coal used in these power stations is won from the Great Northern seam which lies at depths of up to 220 ft at Awaba and at depths of the order of 600 ft at the remaining mines on the southern end of the field.

Jan 1, 1972

By J. P. Grau, J. Z. Lu

"Thickeners/clarifiers are widely used in coal preparation plants, potash processing and other mineral processing facilities. Thickeners play a very important role in slurry treatment systems to accomplish solid/liquid separation. The demand for larger plants and the increased thickener handling capacities sometime require thickener diameters as large as 200m. The development and use of high capacity thickeners makes it possible to increase the handling capacity of these thickeners by several to more than 10 times compared to conventional thickeners. Hence, for a given slurry rate, selection of a high capacity thickener will significantly reduce the footprint of the thickener. Much higher handling rate, higher concentration of underflow, clearer overflow and lower capital cost are obvious advantages of high capacity thickeners; however, some process requirements and the concerns of operational cost, especially the flocculant cost of a high capacity thickener operation, keep some engineers selecting conventional thickeners and staying away from the high capacity thickeners. Forty years after the first high capacity thickener was developed, there are still arguments in the selection of conventional thickeners or high capacity thickeners in mineral processing. The arguments will continue unless there is a clear picture of capital cost vs. operational cost for each of the thickener types. The purpose of this paper is to analyze these costs and to provide guidelines for selection of thickeners. INTRODUCTIONThickeners/clarifiers are widely used in various slurry treatment systems. For mining and mineral processing, thickeners are an integral part of the solid/liquid separation system. The feed to the thickeners are processing slurries. The fundamental mechanism for the solids/liquid separation is for the solid particles in the slurry to gravity settle inside the thickener tank. The clear water overflows from the top of the thickener tank and is typically reused in the processing circuit, and the concentrated underflow is discharged to different downstream process systems depending on the application of the thickeners. The general requirements for a thickener operation include high density of underflow and clear overflow. Since thickener operation consists of continuous feeding, overflow and discharge of underflow, the solid particles will gravity settle against an upward flow with its velocity dependent on the feed rate and the underflow discharge rate. Higher feed rates to a given thickener produce higher upward velocities. Underflow discharge is typically relatively small compared to the amount of overflow. The upward flow tends to take particles up to the overflow. Only those particles having a settling velocity greater than the upward flow velocity will possibly settle out. Hence, thickener feed rate has to be controlled so that the required overflow water clarity can be achieved."

Jan 1, 2012

By A. John R. Hart

INTRODUCTION The use of precast concrete tunnel liners as the initial and final tunnel lining for transit systems has been a major consideration of designers for over three decades. The obvious benefit of building a tunnel that requires only a single pass in constructing the structural lining can provide the opportunity of saving both time and cost. This technique has had worldwide application in transit systems in London, Munich, Hong Kong, Toronto to name a few. In the United States precast liners were evaluated for use on the BART System in San Francisco in the early 1960's but did not provide sufficient confidence in the sealing capabilities available at that time. In 1976 it was decided to call for bids on the Lexington Market Tunnels in Baltimore with a precast concrete liner alternative for one of the tunnel drives. This option was selected by the owner and UMTA to provide a study evaluation for the benefit of the industry. HISTORY In 1983 Washington Metropolitan Area Transit Authority began calling for a series of bids on soft ground tunnels on the Green Line, which included the option of using precast concrete tunnel liners first as an alternative to fabricated steel tunnel liners. Over the years following, the precast concrete tunnel liners have become known as the conventional tunnelling system and, in the last year,

Jan 1, 1989

By S. W. Henley

"Shaft sinking design is typically driven by what has been successful in the past and the availability of sinking plant. This document considers a project where the sinking design and methodology is unconstrained by conventional thinking and removed from the commonly held belief that a sinking methodology should be developed from available winding plant. Schedule was a key driver for the Project and led to an alternative sinking design that aimed to optimise sinking advance rates by specifying new winders that compliment known sinking plant while providing improved safety, redundancy and flexibility within each part of the sinking cycle. KEYWORDS Consistent, Efficient, Flexible, Improved, Innovative, Optimise, Redundancy, Safety, Schedule INTRODUCTION The project is remotely located in the South Gobi region of Mongolia on a brownfield site and the scope of work included the concurrent blind sinking and concrete lining of two (2) ventilation shafts to an approximate depth of 1,150 m at a finished diameter of 10 m and 11 m respectively. All sinking and lining operations to be completed as in-line activities, (no lining whilst other activities are undertaken). The project was schedule driven with a completion date set for the first quarter (calendar) of 2021 and there were no restrictions imposed on the successful Contractor with respect to their equipment selection. Existing sinking plant already onsite from three previous shaft sinking operations would be made available to the Contractor if required on an as is where is basis Sustained advance rates in excess of 2.4 m per day would be required in order to achieve the completion milestone, therefore the design would have to include contingency and demanded flexibility to account for equipment down time. Previous shafts that had been sunk onsite have utilised a single double drum kibble (bucket) winder (hoist) with a single excavator loading on the shaft floor into a large capacity kibble (bucket). DESIGN Mucking The sinking design centred on the mucking cycle given that this is traditionally the most restrictive part of the sinking cycle and typically accounts for one third of the overall sinking cycle. The Vertical Shaft Mucker (VSM) and/or diesel excavator are commonly used plant for shaft sinking that were under consideration. The use of Cactus Grabs was not considered given the higher risk associated with grab ropes and hoist failures."

Jan 1, 2019

By E. H. Kurt

INTRODUCTION The simplest way to drill a hole into rock is to strike a steel chisel or drill bit with a hammer. Early miners used this elementary hand technique so successfully in "single jacking" and "double jacking" that the first mechanical rock-drill designers sought to duplicate it. However, in the early developments, the designers were forced to retreat to a construction known as the "piston drill," wherein the entire drilling element is tied to the piston and reciprocates with it. It took nearly 50 years to devise a method of divorcing the two elements and to achieve the original hammer principle used in hand drilling. The Mont Cenis tunnel, drilled through the French Alps in 1861, usually is considered the birthplace of the mechanical rock drill. The Hoosac tunnel in Massa¬chusetts was drilled at about the same time, and the success of these two ventures paved the way for innova¬tions that produced the Burleigh, Ingersoll, Sergeant, and Waugh piston drills between 1870 and the turn of the century. In 1897, George Leyner of Colorado introduced what has been considered the most significant development in rock-drill history. He devised the hollow drill steel for water flushing; when combined with his free-piston hammer drill, this became the first lightweight and dust¬free underground machine. In addition, Leyner's drills introduced improvements such as automatic rifle-bar rotation of the drill steel and chuck, automatic lubrica¬tion, and an enclosed throttle control. During the 1920s and 1930s, automatic feeds, centralizers, sliding cones, and the automatic water back head were developed, laying the groundwork for all pneumatic underground drills currently in use. Since these pioneering efforts, rock-drill development has been concerned primarily with refining the designs and improving the metallurgy to make faster, lighter, and more dependable machines. Fig. 1 illustrates the progress in drilling speed during the first 125 years of rock-drill development; that progress is a credit to the persistence and inventiveness of the designers in the rock-drilling industry. ROCK-DRILL CLASSIFICATIONS To meet the variety of conditions encountered in rock drilling, several distinct types of drills have been de¬veloped. In general, rock drills may be classified as either hand-held or mounted, with the hand-held ma¬chines including the jackhammer or sinker, the jackdrill or jackleg, and the stoper. The mounted drills are com¬monly known as "drifters." Table 1 shows that each type of drill is available in several sizes from different manufacturers. Fig. 2 illustrates a typical rock drill, showing the principal components. The jackhammer or sinker, shown in Fig. 3, is used primarily for general mine utility work such as drilling anchor holes (short vertical holes to bolt or anchor machinery), pin holes (short, usually horizontal holes to fasten sheaves, etc. to side walls), popholes (for blasting large boulders), and similar applications. They also are used for shaft sinking. Jackhammers are classified ac¬cording to weight, and they range from 7 to 30 kg (15 to 65 lb). The rock drill originally known as a jackleg was made by clamping a pneumatic cylinder or leg to a jack¬hammer, both to support the weight of the machine and to feed the tool forward in horizontal or uphole work. The more modern jackdrill refined this concept to make the hinged pivot for the leg integral with the drill cylinder and to group all drill and leg controls in the drill back head for convenience. Fig. 4 illustrates a typical jackdrill. Jackdrills are classified according to cylinder bore size, ranging from 60 to 83 mm (2.375 to 3.25 in.). Because of their light weight and versatility, jack drills are very effective in small drifts, small tunnel head¬ings, and stoping. The larger machines are applied to hardrock formations and in applications where drilling speed is a primary consideration. In soft formations or

Jan 1, 1982

By Gyimah Kasali

Rapid Load Testing was performed as part of an extensive drilled pier testing program for the University of California Berkeley Capital Improvement Program. The purpose of the program was to: (1) Verify the axial compressive design capacity values for the planned 24" piers, and to estimate the capacity of the existing 30" CIDH piers, and (2) To evaluate the seismic performance of the proposed drilled shafts. The Fundex PLT was used since the loading period of the PLT is very similar to the period of a seismic event, making it an ideal tool to model the pier response to seismic events. "Performance-based design" of structures subject to seismic loads has been of particular interest to UC Berkeley Seismic Review Committee and the Pacific Earthquake Engineering Research Center. The comparison of static tests to Rapid Load testing also provided valuable correlations. The program represents one of the most comprehensive drilled pier test programs on the West Coast. The testing program consisted of Rapid Load Testing using the Fundex PLT on 6 drilled piers. Rapid Load Tests were followed by conventional static compression and tension tests on selected piers, followed by another cycle of rapid load tests on the statically tested piers. The piers featured extensive instrumentation to allow detailed interpretation of the test result. Correlations were drawn to compare static load test result to that of the PLT in the particular soil profile, and the PLT also provided the data to analyze the ultimate seismic capacity of the piers. The load test results indicate that the ratio of interpreted failure load from the PLT data to the corresponding load from the static load test data is about 1.2 to 1.3 for the clayey soils underlying the test site. The results also indicate that the PLT offers an economical approach to defining the stiffness of drilled pier foundations subjected to seismic loads for use in performance-based design.

Jan 1, 2002

By Sharanappa Yalal, Rakesh Kumar Khali

"Himalayan geology poses the most challenging ground conditions almost anywhere in the world, one of the reasons thereof is their evolution as the youngest mountain chains. They are demonstratively rising faster than any mountain elsewhere. The composition is also younger, and consequently less well consolidated than the other older fold belts. This is consistent with the fact that they constitute one of the most active of the plate margin zones rising at a rate that is almost double the Andes, which is in turn three times that of the Alps. Thus, stress conditions (Magnitude and variations) can potentially be more extreme and adverse on a Himalayan tunneling project. Tunnel excavation under the Himalayan Mountains will pose significantly more challenges than an equal length and equal cover drive almost anywhere in the world. These in-depth-tunneling difficulties through high mountainous terrains have posed major challenges for application of traditional drill and blast (D&B) and NATM methods. Handling such adverse geology at any depth is always problematic and generally leads, if not adequately foreseen, to the significant tunneling delays. The author wants to highlight the challenges faced and on the spot solutions adopted while executing most prestigious 273Km long Udhampur –Srinagar- Baramula Rail Link Project (USBRL) in the Himalayas in the state of Jammu & Kashmir, India. The main focus of the paper is on main stretch of USBRL Project i.e. T-80 (India’s 2nd longest railway tunnel & 3rd longest in Asia) where the team of the author has recently completed a 11.2 Km long tunnel and where the train track has gone operational from Qazigund to Banihal. The construction of this stretch posed several challenges akin to highly adverse geological conditions. Executing on -the -spot solutions, the project has been completed successfully. 1.0 INTRODUCTION Construction of Udhampur-Srinagar-Baramulla Broad gauge railway line is one of the Mega projects undertaken by Indian Railways to establish a dependable transportation in the state of Jammu and Kashmir. In engineering terminology, it is a challenging project negotiating breakthroughs against the complex Himalayan geology. The Project which has been operational over last 12 years , stretch by stretch, is in advance stage of construction . The purpose of the prestigious project is to connect the Kashmir valley to the mainland of the state of the country. On the date owing to the hurdles of the tuff terrain, the transport of this part is totally dependent on the surface transport, i.e., through a road which connects NH-1A from Delhi to Srinagar. The altitude of the region varies from 500.00 to 1700.00, ranging through Udhampur to Katra - Reasi –Sangaldan- Banihal-Quazikund-Ananthnag-Srinagar-and Baramulla. The main features of this project are its Pirpanjal Tunnel and T-48 & 49 tunnels which cover the maximum length of tunneling through thick hostile geological conditions, the total length being 138km. Details of Pirpanjal tunnels are shown in Figure-1."

Jan 1, 2016

By Jerry T. McLendon

The proper disposition of phosphatic clays has been the subject of research and debated for years by phosphate producers, State and Federal research agencies, regulatory authorities, and environmentalists. To date, no "universal" solution exists for the ultimate disposl of phosphatic clays. This Bureau of Mines report examines the state of conventional clay disposal technology and reviews the technical progress of innovative alternatives. Twenty impoundment sites were investigated by the Bureau of Mines using geotechnical methods and laboratory analysis of cored samples. In addition, quasi-static cone penetrometer soundings were conducted to define clay and/or sand-clay interfaces en masse. Samples of the top, middle, and bottom hole segments were obtained at each station for laboratory studies of clay densities, pore fluids, plasticity, and mineralogical properties. The results of this study support the continued use of initial clay settling impoundments but emphasize the need for "in-line" systems to reduce the initial volumes of plant-generated phosphatic clays. The effective use of sand tailings is also encouraged to promote further consolidation of clays via self-weight stressing, sand-clay admixtures, and/or surcharging sand caps.

Jan 1, 1984

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, F. J. Tavitas-Medrano

319-type cast Al-Si-Cu-Mg alloys are commercially important due to their popular use in automotive applications. Artificial aging heat treatments are commonly performed in these alloys to achieve precipitation hardening and, therefore, improve their mechanical properties. The present work was carried out to investigate the effect of conventional (at a constant temperature, as specified by the standard T6 heat treatment regime), and non-conventional multi-temperature and interrupted aging cycles on the hardness, tensile and impact properties of two 319-type alloys (with and without Sr+ Mg additions). The results show that certain multi-temperature aging cycles have a more favourable effect in improving some mechanical properties than conventional cycles.

Jan 1, 2006

By A. G. Pasamehmetoglu

This paper describes the conver¬gence and load measurements carried out in inclined seams at five longwall faces, two of which were supported by hydraulic props and the other three by conventional timber supports in Karadon-Gelik mine. The minimum support capacities determined in this study are compared with the results obtained from two empirical approaches suggested by Wilson (1975) and Jacobi (1981). The characteristics of hydraulic props to be used and support patterns in the longwalls are found, conclu¬sions are drawn and suggestions are made. Design nomograms are prepared for field engineers, in order to be able to approach the problem more confidently and realistically.

Jan 1, 1992