Search Documents

The subject of heat sources in deep hard rock mines, the limitation of forced ventilation to cope with these heat loads and the sizing of refrigeration plants to boost the cooling effect of the ventilation air are discussed. The development of plant selection criteria and operating experience at North Broken Hill Limited is outlined. Future options for North Broken Hill Limited and like deep mines are summarised.

Jan 1, 1982

By Edward Jacobsen, Patrick J. Lydon

"The ongoing expansion of the Oak Creek Power Plant in Oak Creek, Wisc., includes a tunnel bored in rock that connects to four vertical intake shafts approximately 1.5 miles (2.4 km) offshore in Lake Michigan. In 2004, Case Foundation Company was awarded a lump sum contract to install these intake shafts. In spite of delays that shortened the May to September construction season by up to 50%, four shafts and liner assemblies were drilled in 2005 and 2006. The shafts were connected to the tunnel in 2007 by mining upward to reach the lower portion of each liner and then removing its internal bulkheads so that lake water fl owed into the tunnel. The project is one of the largest private construction projects ever undertaken in Wisconsin. The expansion adds 1,230 megawatts of generation. In addition to the tunnel and offshore work, there will be 16 miles (26 km) of railroad track and 6 million cubic yards (4,600,000 m3) of earth work. The 27 ft (8.2 m) diameter tunnel, drilled some 150 ft (46 m) below the surface of Lake Michigan, originates onshore at a pump house. A structural slurry wall was constructed as the foundation for the pump house. The tunnel passes to the south near the current water intake before bearing east toward the new offshore intake shafts, which are 12 ft (3.6 m) diameter by 108 ft (33 m) long steel liner assemblies. These were grouted in place from approximately 3 ft (1 m) above the crown of the intake tunnel and then to 20 ft (6 m) below the lake bottom.Site GeologyOffshore. The plant site is north of the Racine-Milwaukee county line in an area affected by glacial activity. The soil conditions encountered at each shaft location were consistent, with noticeable variations occurring in the top of rock elevations that sloped downward from the innermost to the outermost shaft."

Jan 1, 2008

By R. C. Head

The investigation describe the history of copper in the seventties, as well as indicates the forecast the probable trend of the Copper Industry over the coming decade, and second, to stimulate some discussion on what is a somewhat controversial subject. At the same point, the period of surplus production from about 1972 to 1976-1977, during part of which some voluntary restriction on output maybe necessary. In consecuence, its a necessity for forward planning so that, by 1973-1974, new mines maybe developing to preserve the continuity of supply .

Nov 20, 1969

By John Petty, John Loviza

Single sentence describing content-- "The best ally an Explosives Engineer can have in a court of law is a regulations enforcer stating all codes and standards were met on a jobsite".

Jan 1, 1996

By John Petty, John Loviza

As a blaster, have you ever had that uneasy feeing in the pit of your stomach as a codes enforcement official drives onto your jobsite? Have you ever needed an ally in a court of law against an unjust damage claim? Have you ever wished for a better and more open relationship with the guys who wear the badges?

Jan 1, 1996

CARNEGIE INSTITUTE OF TECHNOLOGY On May 27, twenty-five of the leading representatives of the coal mining industry of Western Pennsylvania met with President A. A. Hamerschlag, of the Carnegie Institute of Technology, with a view to bringing about closer relations between the Institute and the mining interests. It was felt that the advice of the men in the field was necessary for the proper training of young men for mining work. A resolution adopted at this conference, among other things, called for a board of mine operators and engineers to serve in an advisory capacity with the Carnegie Institute of Technology. As a result of the counsel and recommendations of the Advisory Board, the Carnegie Institute of Technology, in cooperation with the U. S. Bureau of Mines, has recast its four year course in Mining Engineering and has also established a two-year course in Coal Mining. To carry out this new program, there has been organized the "Cooperative Department of Mining Engineering" in the Division of Science and Engineering of the Carnegie Institute of Technology.

Jan 8, 1919

By O. E. Kiessling

A GROWING uneasiness in the oil fields indicates that doubts are arising as to the efficiency of the present technical, economic and legal arrangements affecting production. Recent documents of the federal government, debates in state legislatures, editorials in the daily press and statements of oil company executives re-echo the notion that the present methods of producing oil satisfy neither the business man nor the public. Such intimations are of utmost importance, since oil is a vital clement in modern industry and dependence upon it increases as new uses develop. SECTION I-PRESENT SCHEME OF COMPETITIVE EXPLOITATION IS WASTEFUL The oil industry has convinced itself, for very good reasons, that the present scheme of competitive exploitation results in losses, both in terms of quantities of oil and in terms of profits. The story of these losses is familiar enough, and it is necessary only to distinguish and summarize briefly certain factors that are of importance to the following argument. Oil pools are exploited under a competitive economic system based on private ownership and contract; the hope of profits attracts capital and enterprise, and competition is supposed to serve as a regulative factor. Whether such a scheme of industrial organization works is partially dependent on the ability of the producer to withhold or produce is commodity as he sees fit, in accordance with the dictates of market demand.

Jan 1, 1927

By O. E. Kiessling

THE present system of competitive exploitation of oil pools results in losses, both of petroleum and of profits. Under a competitive system the owner produces or withholds his product according to the price, which reflects the demand, but in the pe-troleum industry the producer does not have complete control over the expansion and contraction of his out-put. Under a series of court decisions, reviewed in detail in the paper, petroleum is not covered by- the general theory of English common law that the owner of land owns everything from the center of the earth to the sky within the areal limits of his property, but is considered to be his only when he has reduced it. to possession, which he can only do by taking it out of the ground. If A can obtain possession of the petro-leum which is beneath the property of B without tres-passing on B's property he commits no legal wrong and B has no defense except to get it into his (surface) possession before A takes it. No one would expect an. owner under such a system to forego the possibility of securing some oil from his property in order to in-crease the ultimate production of the pool. The pe-troleum industry. should offer a constructive program, that will eliminate losses and protect the interests of individuals as far as possible. If improved methods of oil recovery can be applied the quantity of petroleum recovered might be double or even treble the amount recovered by ordinary procedure. But increased recovery is not the only benefit from pool development. In brief, the following advantages can be claimed for unit operation: 1. Saving in development and operating costs. 2. Less danger of damage to the fields by defective wells. 3. Development is better gaged to fit market demand and to effect the most efficient recovery of oil. 4. More oil, gas, and gasoline can be marketed. 5. By regulating pressures, recovery .of oil and gas will be greater and the wells will flow longer. Reagan County (Big Lake), Rainbow Bend and Cabin Creek are examples of longer life of pools thus obtained.

Jan 11, 1927

By C. W. Grate

Cooperative Education is by no means a new idea. The first such program was instituted at the University of Cincinnati in 1906 by the late Dean Herman Schneider with twenty-seven engineering students participating. Today, more than fifty years later, there are in excess of one hundred institutions' with some such program in which thousands of students, are participating in the fields of Liberal Arts, Engineering, and Business Administration. At the same time, according to a conclusion reached during a study of work-study college programs, copyrighted in 1961 by Thomas Alva Edison Foundation, and from which we quote; "We were amazed at the lack of-information about cooperative education among school and college staffs and students, among parents and employers, and on the part of the public generally."

Jan 1, 1963

By W. A. Vine

Next year, in 1964, Butte will celebrate its Centennial. It was in May, 1864, that the first recorded mining activity took place. During that summer, several rich placers were found on Silver Bow Creek and its tributaries, and a gold rush followed. As placer mining proceeded in the creek beds, the quartz lodes on the hillsides were located and the veins were prospected. Mining in Butte entered its second phase when the rich silver mines, the Alice, Moulton, and Lexington, were opened. The silver boom lasted until the decline in the price of silver in the early 1890's forced the closure of many of the mines. An indication of the beginning of the copper mining era in Butte was in 1866 when it was noticed that green copper carbonate discolored some of the, lode material. It was not until ten years later, however, that the Anaconda and St. Lawrence claims were located by Michael and Ed Hickey. The claims were sold in 1880 to Marcus Daly and in 1881, Daly obtained financing and organized the Anaconda Silver Mining Company to exploit the vein The silver venture was a failure because of the predominance of copper which diluted the bullion to only 400 fine.

Jan 1, 1963

By Joseph Hodgson

Introduction SINCE about 70 per cent. of the total cost of mining is due to underground work which is out of sight, it is essential that expenditures should be made here to the best advantage. A great many mistakes have been made which were expensive, but perhaps these have not even been detected by mine owners. In the future these may be minimized to some extent, especially if there is cooperative effort on the part of each employee. I have been interested in this subject for some years and have tried to deduce principles and methods. These have proved highly advantageous and may also be of help to others. Some corporations, like the United States Steel, and the Cleveland-Cliffs Iron Co., have done a great deal in this field by having stated meetings of their organizations, with the view to interchanging ideas among their men and educating them along the lines of concerted effort. Since no man knows all about the various branches of mining, it is advisable that frequent meetings of the operating department be held for the interchange of ideas and that all members of the organization have an opportunity to express themselves on the various subjects. It has often been found that in discussions between heads of departments, foremen and bosses, many valuable suggestions may be obtained which promote the best interests of the company. The method regarded as the most conducive to cooperative effort, and pursued by the organization, is to analyze and develope the different phases of various mining subjects at regular meetings.

Jan 5, 1916

By Joseph P. Hodgson

JOSEPH P. HODGSON.-As to ".Safety First," I did not deal with that, but I will say that in 1913, the number of .men killed was nine, and that year the "safety first" program was commenced; the next year, 1914, the number was reduced to five. In 1915, I am pleased to say that the number was reduced to two in the Copper Queen's entire property, and we have none so far this year. THE CHAIRMAN (G. F. G. HERMAN, Bisbee, Ariz.).-I can say, further, that we have from eight to nineteen men per month incapacitated for more than 14 days. Those are classified in this State as serious accidents. The number of men injured has apparently increased, -but that is clue to our improved method of recording and classifying accidents, no matter how slight. C. W. GOODALE, Butte, Mont.-The importance of cooperation among the members of the staff of an industrial organization is well brought out by Mr..Hodgson's paper.

Jan 12, 1916

By Herbert F. ?Buck? Darling

A bridge replacement project in Rochester, NY, encountered difficulties when it was determined that rock below one pier was sloping downward toward the river at an angle of 42 degrees versus anticipated 12 degrees. Cofferdam design and construction became very difficult. The unanticipated subsurface conditions delayed the project by eighteen months and increased the cofferdam cost by almost $3.0 million ($US) when direct costs and associated delays were taken into account. The initial approach after discovery of the problem was to use the same type pier design and modify the cofferdam accordingly. This resulted in a cofferdam 12 meters (39.4 feet) deep on the shore side and 18 meters (59.0 feet) deep on the water side. The design used a master pile system to attain required wall strength and used rock anchors to prevent the cofferdam from moving toward the river. The pier foundation was then redesigned by the owner using revised seismic parameters. The original stepped footing carved into rock was replaced by caissons socketed into the rock beneath a large tremie concrete placement. The revised pier and cofferdam designs caused a shift from a mostly land based cofferdam, excavation, and rock removal project into an almost entirely water based cofferdam, caisson drilling, and tremie construction project. These design changes resulted in a reliable, safe, and unusual cofferdam and construction method. All of this was accomplished within a very narrow worksite with a railroad on one side, and the river with its public and commercial freighter traffic on the other. In addition, the existing two-leaf drawbridge was to be maintained in place which put further limitations on the water borne equipment. The engineering and construction considerations, problems, and solutions related to these cofferdams and pier foundations are presented.

Jan 1, 2013

By W. C. MENDENHALL

THE problem of maintaining the mining industry is two-fold; finding new supplies in the face of increasing difficulties, and making such advances in the arts of extraction and preparation as to use supplies of lower grade. Progress in mining and reduction methods and in transportation makes ore today of that which was waste yesterday. These are the fields of the metallurgists and the transportation engineers. The geologists and mining engineers must work together on the problem of ore finding. As the old prospector fades from the scene, men with equal hardihood and patience and equal power to meet the physical obstacles which confront the seeker after ore, must take his place, armed with all that has been learned from human experience about the causes, the controlling conditions, the indications, and hiding places of the metals. Such a seeker is dealing with some of the most complex and obscure of natural phenomena. In nature's laboratory, tremendous forces are at work. Tempera-

Jan 1, 1926

By Donald M. Keagy

How many times have you said or heard someone say, 'What are you doing right now?" And how many times have you heard the reply, "Breathing air!" Probably never, or at most only a few times in a facetious vein. Breathing air is absolutely necessary to sustain human life, and yet most of us take it completely for granted. Beginning ten to fifteen years ago there was growing concern on the part of the general public that pollution of the air is a threat to man's health and welfare. Concurrently much thought and effort was devoted to the task of defining and resolving the problem of air pollution. In the course of this effort it has become quite clear that our National policy in this regard should be founded upon three basic axioms: (1) Action should not be postponed until emergency conditions make it compulsory; (2) The air cannot be purified after it is polluted, and (3) Air pollution control cannot be accomplished without close cooperation among all levels of government, industry, and the public.

Jan 1, 1967

Design and test a high-production coal mining machine that generates less respirable dust. Background Current coal cutting systems generate excessive amounts of airborne respirable dust and fines during the mining process. Dust control technologies, including dust dilution by ventilation and suppression by water sprays, are not always able to reduce dust levels sufficiently. The U.S. Bureau of Mines (USBM) has designed a cutting system that reduces respirable dust generated by the cutting action of the drum. This cutting system, based on geometric principles developed in the 1500's, makes use of a constant depth, linear cut to remove coal at deeper cut depths and at lower rotary speeds than a conventional rotary drum. A comparison of the linear and rotary cut paths is shown in figure 1. Approach A full-scale prototype of the linear cutting concept was valuated under laboratory conditions to determine its performance relative to standard rotary drums. Results of these evaluations show production of fewer fines, or more uniform product size, a significant reduction in the amount of airborne dust, and reduced torque and power requirements (figure 2). On the basis of these results, a contract effort was undertaken by McCracken and Associates of Bristol, TN, to design a linear cutting head for underground testing.

Jan 1, 1995

By B McIntosh

Sustainability in its simplest assessment has been defined as æmeeting the needs of the present without jeopardising the needs of future generationsÆ. For the mining industry alone, this statement could indeed be interpreted by the many cynics in our community as an oxymoron; as miningÆs very existence requires the extraction and consumption of finite resources. However for the future of industry as a whole, the integration of mining, minerals processing and manufacturing presents us with a unique opportunity to achieve sustainability through the continued supply of metals and materials for society, in a manner which can achieve positive social outcomes through a triple bottom line approach.The Kwinana Industrial Area has been Western AustraliaÆs premier heavy industrial precinct for more than 40 years and its prevailing level of prosperity will ensure it remains a significant contributor to the State economy through the 21st century.The Kwinana industries depend on each other for the production of essential raw materials vital to their manufacturing and refining process, an innovation that also has significant environmental benefits.Formed in 1991, the Kwinana Industries Council strives to foster positive interaction between member companies and with the local community.The aims are:to co-ordinate the activities of Kwinana industries on a range of common issues; provide effective liaison with the local community; promote a positive image of Kwinana industries; highlight contributions to the community by Kwinana industries; and work towards the long-term viability of the Kwinana Industrial Area. The Kwinana Industries Council facilities these aims by focusing on developing and employing leading edge technology, giving workplace health, safety and environment top priority, and taking a committed, responsible and pro-active approach to environmental protection, whilst forging a two-way partnership with the local community.The sustainability of industry is the key objective for the Kwinana Industries Council and through the involvement of the 13 member companies industry strives to:achieve efficient processing of resources to provide a range of goods and services needed by the community; achieve acceptable and decreasing level of environmental impact; provide jobs and income for our community; and engage co-operative projects that benefit the local communities, the State and Australia.

Jan 1, 2004

A number of cooperative studies have been carried out as preliminary work for drafting a standard for application of granulated slag sand for concrete, and the following conclusions were reached 1 The ten kinds of granulated slag sands pro- duced in Japan satisfy the national standard for fine aggregate in terms of physical and chemical properties. 2 Mortar and concrete tests conducted with granulated slag sand revealed that, although with slight differences in the extent, gran- ulated slag sands used in these tests were applicable'as fine aggregate for concrete, 3 The pumpability test by a concrete pump carried out on concrete with two kinds of now commercially available granulated slag sand demonstrated that the pump pressure feeding is applicable in the same manner as in the case of ordinary concrete. These tests permitted' preparation of a draft standard for application of granulated slag sand, and the results formed the first step toward utilizing this material as a sub- stitute for natural sand.

Jan 1, 1979

By J. G. Thompson

THE methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value represent-ing the sum of the oxygen contents of several or all of the oxide con-stituents present. With such diversity in the principles and. aims of the different groups, it is not surprising that concordance of results by differ-ent methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the vari-ous methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metal-lurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1936

By Jan G. H. du Preez, C. Viviers, B. J. A. M. van Brecht, H. E. Rohwer, Nicole M. Sumter

"At the basis of metal ion separation lies some particularly metal ion specific chemical property which lends itself towards exploitation. This could be in the form of an anionic complex or a neutral chelate complex. In the former a cationic centre with a particularly high affinity for the complex will have to be designed. In the latter case a stereospecific chelate ligand containing the correct symmetry and type of donor atoms will have to be designed. In both above cases the ""active centre"" can be entered in a from that it can function in different media of hydrophobicity, eg a precipitant, a resin or a solvent extractant. Recent results obtained in this laboratory will be used to illustrate how the above variables can be exploited to develop improved processes for the separation of base metal and platinum group metals.IntroductionThe separation of metal ions in hydrometallurgy can be performed broadly speaking with two major aims. Firstly the separation/removal of a certain group of metal ions, either as a means of preconcentration or as a removal from effluent as part of a purification process and, secondly the removal of a specific metal ion from an industrial stream in order to produce a specific metal in a pure form. This latter operation is by far the most difficult of the two and is becoming more so in the light of the fact that the world is moving in the direction of lower grade ores and increasing pollution. Such a process can be divided into three essential parts, firstly the molecular one in which an active centre is required to obtain specificity, secondly a matrix within which this active centre must function, i.e. as part of a resin or solvent extractant and thirdly the design of the total system to optimize the realization of the operation."

Jan 1, 1996