Search Documents

By M Coulthard, J Rivalland, K Dugan

Prior to 2001 Yallourn Mine has pumped approximately 1000 Megalitres of water per annum from aquifers beneath the mine floor in order to control aquifer pressures that were thought to have an influence on mine floor and permanent batter stability. In 2001 one of the deep aquifer pumps was shut down for five months in order to measure the aquifer recoveries. Prior to the shutdown a UDEC model was created in order to predict what level of recovery in the aquifer pressures would be critical to mine stability. The shutdown showed that the aquifer levels recovered and stabilised at levels that did not threaten the stability of the mine. The aquifers recovered to levels below the critical levels identified in the UDEC model.

Jan 1, 2003

By R. K. McFarland, E. S. Diamant, L. Blake

A number of concepts for basing strategic missiles facilities deep underground have been developed within the defense industry. Recently, several contracts were let by the Air Force Ballistic Missile Organization to better develop system concepts for Deep Basing and Rapid Egress of Missiles from these facilities. A particular challenge of the Deep Basing Concept is the need for the excavation of egress tunnels or shaft from the deeply based facility to the ground surface, in a rapid and reliable manner. This Paper describes a conceptual MX-Deep Basing Facility, the technical issues associated with its design and construction, and potential means for achieving rapid egress from this facility. Manuscript not received in time for publication.

Jan 1, 1983

By T. G. Paradis, C. A. Mohns

"This paper summarizes the Wren CAT (Clarifier and Accelerated Thickener) deep bed thickener operation at the EKATITM Diamond Mine in Canada’s Northwest Territories. EKATITMs’ thickener project is presented in terms of initial design considerations and present day operating practices. A circuit description summarizes process equipment, reagent systems, and typical process conditions, and details of Wren CAT operating principles are provided. Operating strategies are discussed, with emphasis on process instrumentation and control and operating challenges.INTRODUCTIONThe EKATITM diamond mine, operated by BHP Diamonds, Inc., is located in the Northwest Territories near Lac De Gras, approximately 300 km NNE of Yellowknife, NT. 9000 dry metric tonnes of diamond-bearing kimberlite ore are processed daily. Processing operations commenced in October, 1998.The EKATITM process plant flowsheet features typical steps in diamond recovery plant design. Figure 1 shows the general plant flowsheet. Size reduction and feed preparation are accomplished by crushing, scrubbing, and high pressure grinding rolls (HPGR) through closed-circuit classification with vibratory screens. Heavy medium separation (HMS) is used as the initial stage of heavy mineral concentration. Secondary concentration is accomplished in the recovery plant by attrition milling; wet, high-intensity magnetic separation (both wet and dry); and X-ray sorting.The present budget throughput rate is 9000 dry tonnes per day. This will be increased to 18,000 tonnes during the first ten years of operation. Unlike most kimberlite treatment facilities, which process material from a single ore body, EKATITM’s process plant was designed to accommodate ore from five different kimberlite pipes, each with its own treatment characteristics.All processing, except for primary crushing, is carried out in a temperature-controlled environment in the main process plant building."

Jan 1, 2000

By W. Sondermann

"AbstractThe construction of a distribution centre of minerals for a global mining and resources cooperation demanded the control of deformations and displacement of the stack reclaimer facilities on very inhomogeneous subsoil conditions. The variation of quality from soft clay with CPT values below 1 MPa up to rock formations were the challenge in design and execution of all the foundation works.The advanced design considerations were resulting in a barrier wall system to limit the deformations of the up to 40 m deep bored pile of the stacker-reclaimers, whereas the layout of the barrier wall and the stiffness of the elements had a major impact on the residual lateral forces to be absorbed by the bearing structure.IntroductionA large international raw material distribution organisation is currently building an iron ore and pellet distribution centre on the north-western coast of Malaysia. The distribution centre will handle around 90 MTPA (million tons per annum) of iron ore and includes accompanying plants for loading and unloading iron ore and pellets, pelletizing plants as well as corresponding storage space for these raw materials. The total storage space extends about 800m north to south respectively 1400m east to west and is about 200m from the coastline. The project area is located in a wide valley basin, bounded by a range of hills to the north. The existence of soil with low bearing capability in the area designated for the plant meant that measurements for ground improvement were required in the storage areas, in order to combine the needs of iron ore and pellet storage areas with requirements of the loading facilities as the overall project demand.Project LayoutThe iron ore distribution centre and the pelletizing facility both consist of an import/export jetty, material handling facilities, pellet plant and the associated infrastructure. This publication describes the execution of ground improvement and foundation works for the loading and storage system, which consists of five rows of stockpiles and four intermediate rows of stacker-reclaimers. The total area of these systems comprises 278,881 m2 (Fig. 1)."

Jan 1, 2014

By Judith S. Chan

With the increasing awareness of the need for the reduction of carbon emissions globally, geothermal energy, which offers a potential for cleaner energy generation, is one potential new source. In Alberta, these geothermal resources are likely to be found in the sedimentary basin, or in the deeper crystalline basement rocks. Alberta exhibits a very low geothermal gradient compared to other existing geothermal fields located in areas of volcanic and tectonic activity. To mitigate this effect, the focus in Alberta will involve the development of engineered geothermal systems (EGS) in the target resource. The first goal for EGS research and development is to develop a detailed geological-geophysical characterization of selected sites to delineate potential geothermal reservoirs in Northern Alberta. One of the selected sites is in the Fort McMurray area. The deepest well drilled in the oilsands areas of Northern Alberta is located just west of Fort McMurray. It has a depth of 2363 m and as such can provide details on the physical properties of the rocks, the state of stress, and the existence of fracture porosity toward geothermal investigations. To date, we have acquired temperature logs to study the change in geothermal gradient with depth, and a series of petrophysical logs to study the finer scale structure of the rock formations with vertical resolutions in the range of 0.05 cm to 80 cm. Our aim is to identify geological features such as zones of fractures in the basin and/or basement that could provide an indication of enhanced fluid flow potential ? a necessary component for any geothermal systems to be viable. Zero offset and walkaway vertical seismic profiles (VSP) were also conducted to measure the seismic responses at the borehole. VSP data can be used to delineate the structural and stratigraphic features surrounding the borehole that could not be resolved from surface seismic reflection data that are also available near the borehole. The full integration of well logs, VSP data and surface seismic reflection data are expected to provide a detailed characterization of the sedimentary basin and crystalline basement rocks of the Canadian Shield in Northeastern Alberta and will assist in future planning for drilling.

Jun 1, 2012

By Oswald J. Heinrich

(Supplementary Paper.) IN conclusion of a series of deep exploration-borings with the diamond drill, I beg to submit the following statements, supplernentary to those in my former papers on this subject: Since my communications read at the St. Louis Meeting, in May last, I have finished two more borings, one terminating at the depth of 922 feet 7 inches, the other at the depth of 715 feet 6 inches. The results in regard to time and expenditure have been highly favorable and fully confirmatory of my opinion stated in previous

Jan 1, 1875

By C. Y. Liu

This paper principally deals with the application of caisson foundation in the Chinese bridge building industry, the different types of caisson foundation adopted, and their spheres of application. Caisson foundation has been used and speedily developed for bridge works in New China, and a number of new innovations have been made in its design. Especially in deep water foundation, the Nanjing Bridge over Changjiang has attained one of the deepest bridge foundations in the world. There are six types of deep caisson foundation being now in use in China, namely:

Jan 1, 2010

By Sameh M. Khella

This paper discusses the application of deep CFA piles for the foundation of structures in different ground stratifications with a focus on the application in Queensland region. Design, construction techniques and quality measures implemented during these procedures are described. Testing methods and verification of capacity, integrity and performance of these piles are also demonstrated. Case studies for this application are presented with an appreciation of this solution within the provided project conditions of each case. Examples of successes and challenges encountered over the course of application of deep CFA in Queensland are mentioned. Limitations of the technique and less favourable situations for its implementation are also highlighted.

Nov 1, 2022

By William F. Campbell

One of the deepest coal operations today is the Springhill No. 2 mine of Cumberland Railway & Coal Co., subsidiary of Dominion Coal Co. Ltd. Mining is now conducted at a slope distance of 14,000 ft, with 4400 vertical ft of cover. The record of Springhill No. 2 can be said to contain the history of bumps in the Province of Nova Scotia. The Springhill coal field forms part of the Cumberland field of Carboniferous age. There are seven mineable fields in the area, numbered in the order they were discovered. Mining has been carried on in all but the No. 4 and 5 seams, but present operations are confined to the No. 2. Fig. 1 shows a vertical section through the seams.

Jan 9, 1958

By Z. G. Lin

In Xian, China, compaction by means of soil (or lime-soil) piles is one of the effective methods widely used for densifying loess and eliminating its collapsibility. However, as a result of groundwater table rising, it is no longer applicable in many areas. This paper is the summary of the first-time use in Xian of sand-gravel compaction piles aimed at densifying the miscellaneous fill (already partially under water) and saturated loess at a certain project site. In-situ tests, conducted before and after the treatment and including several kinds of penetration tests backed up and confirmed by a set of plate loading tests, yielded very satisfactory results, strongly testifying to the viability of the method.

Jan 1, 2010

By Dennis Nottingham

The need for deep compaction of submerged granular soils has led to improvements in this area. In 1971, L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100 foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers? experiments, observations and measurements, led to an ?H? pile probe design which has produced measured soil density improvements up to 250% using SPT ?N60? values as a measure.

Jan 1, 2013

By Tulu B. Ihsan, Mark A. Van Dyke, Ted M. Klemetti

"How well do current modeling procedures calculate the rear abutment extent and loading? Does an improved understanding of the rear abutment extent warrant a change in standing support in bleeder entries? What is the optimal standing support for bleeder entries separated from the longwall startup room by a barrier pillar? To help answer these questions and to determine the current utilization of standing support in bleeder entries, four bleeder entries at varying distances from the startup room were instrumented, observed, and numerically modeled. This evaluation was intended to determine the rear abutment extent and magnitude at various locations to optimize standing support in these entries and those under similar conditions. This paper details observations made by NIOSH researchers in the bleeder entries of a deep cover longwall panel; specifically data collected from instrumented pumpable cribs, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was on the extent and magnitude of the abutment loading experienced by the standing support. As expected, the instrumentation of the standing supports showed very little loading relative to the capacity of the standing supports—less than 25 tons load and 1 inch convergence. The observations of the conditions showed little to no change from before the longwall panel extraction began to when the panel was more than 50% extracted. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the bleeder design. The Flac3D program was used to evaluate these four bleeder entries using previously defined modeling and input parameter estimation procedures. The results indicated only a minor increase in load during the extraction of the longwall panel. The model showed a much greater increase in stress due to the development of the gateroad and bleeder entries, with about 80% of the increase associated with development and 20% with longwall extraction. The Flac3D model showed very good correlation between expected gateroad loading during panel extraction and those expected based on previous studies. The front and side abutment extent modeled was very similar to observations from this and previous panels with similar conditions. The results of this study showed that the rear abutment stress experienced by this bleeder entry design was minimal. The convergence measured in these bleeder entries was small enough not to mandate any additional support beyond development even by U.S. or Australian standards. The pumpable crib load and convergence experienced depends on the geological setting, mining geometries, and timing. The farther away from the startup room, the lower the applied load and smaller the convergence in the entry if all else is held constant. Finally, the numerical modeling method used in this study was capable of replicating the expected and measured results near seam."

Jan 1, 2017

By Keith A. Heasley, Frank E. Chase, Christopher Mark

Deep cover retreat mining (overburden in excess of 750 ft) is an important emerging issue which will intensify in the future as the more easily mined shallow seam reserves are depleted. Analysis of Mine Safety and Health Administration (MSHA) statistics indicates that deep cover pillar recovery accounts for a disproportionate share of the underground coal mine roof/rib fall fatalities and injuries. Past research has shown that previously recommended Analysis of Retreat Mining Pillar Stability (ARMPS) stability factors (SF’s) may be excessive for deep cover pillar design. The objectives of this study were to evaluate the various methods and strategies by which panels, production pillars and barrier pillars are developed and extracted under deep cover, and to develop appropriate design guidelines. In the course of the research, 29 mines in 7 states were investigated to collect panel design case histories. At each mine site, underground geotechnical data were collected on the pillar line in order to document roof rock, coalbed and floor conditions. The analyses indicated that squeezes were the most likely failure mode where the depth was less than 1,250 ft, but bumps predominated in the deeper cover cases. Immediate roof rock quality, the ARMPS SF’s, and barrier pillar stability factors were all found to be important parameters in determining the outcomes of the case histories. Design guidelines, including suggestions for barrier pillars to isolate active panels from nearby gobs in bump prone ground, are also proposed.

By Chris Mark

In the wake of the Crandall Canyon mine disaster, the U.S. Congress asked the National Institute for Occupational Health and Safety (NIOSH) to study the safety of deep cover pillar recovery operations in the US. The legislation defined ?deep cover? to be greater than 1,500 ft, but NIOSH is also evaluating mines at depths greater than 1,000 ft when multiple seam interactions are encountered. By these definitions, there about 35 active mines that engage in deep cover pillar recovery, in the states of UT, CO, VA, WV, and KY. To date, NIOSH has documented ground conditions and ground control experience at nearly all of them. This paper provides an overview of current deep cover pillar recovery practice. Specific ground control issues that are discussed include: Pillar and barrier pillar design, ? Coal bumps, Thick seam pillar extraction, and ? Multiple seam interactions.? INTRODUCTI

Jan 1, 2009

By E. R. Bauer

The trend in underground room-and-pillar coal mining is to employ remote-control continuous mining machines and extended cuts, 12 m (40 ft) deep or more. This system of coal extraction, adopted by over 435 mines, can create additional worker-safety hazards. To address the ground control and worker-positioning hazards, a combination of statistical analyses and numerical modeling was conducted. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the Coal Mine Roof Rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling to predict roof displacements during extended-cut mining was completed. The paper describes the results of these studies and their impact on the safety of extended-cut mining.

Jan 1, 1999

By Richard Stoltz, Gary Smith

This paper presents the findings of a face ventilation investigation, conducted by the Ventilation Division, Pittsburgh Health Technology Center, at a underground coal mine operating in the Illinois No. 5 coal seam. The purpose of the investigation was to evaluate the effectiveness of a blowing face ventilation system in controlling methane liberation in the face area while mining with brattice distances up to a maximum of 40 feet from the face (extended cut). The continuous miner on this section was remotely controlled and equipped with a machine mounted dust collector. Data collected during this investigation included methane concentrations, intake and return air quantities in the face area, and scrubber air quantities. In addition, a time study was conducted to correlate the methane peaks to activities in the face area. In conjunction with the face study on Section A, separate methane liberation studies were conducted on three additional sections: B, C, and D. This was done in order to compare intake methane concentrations and methane liberations from other sections in the mine to the test section. Calculations indicated that the minimum intake air quantity necessary at the inby end of the line brattice for the section investigated was 7,000 cfm. Due to the higher intake methane concentrations and average methane face liberations measured on three other sections, the minimum air quantities necessary at the inby end of the line brattice were determined to be 13,900 cfm, 11,100 cfm, and 15,000 cfm, respectively.

Jan 1, 1991

By E. R. Braer, C. J. Bise

The trend in underground room-and-pillar coal mining is to employ remote-controlled, continuous-mining machines and extended cuts to depths of 12 m (40 ft) or more. This system of coal extraction, adopted by more than 435 mines, can create additional worker safety hazards. To address the ground-control-related safety hazards, a combination of statistical analysis and numerical modeling was used. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the coal mine roof rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling was completed to predict roof displacements during extended-cut mining. This paper describes the results of these studies and their impacts on the safety of extended-cut mining.

Jan 1, 2000

Reduce the airborne dust generated in a longwall coal face. Approach Reduce the rotational speed and increase the depth-of-cut of the longwall shearer. How It Works An Anderson-Mavor AM500 double-ended ranging drum shearer was fitted with drums specially designed to accept the large picks required for this testing program. Change gears In the shearer allowed rotational speeds of the drums to be set at 35, 45, 55, or 70 rpm. As deep cutting removes larger coal fragments, the specific energy requirements of the operation are reduced and less surface area results. Dust generation and shearer power consumption are also reduced. The lower rotational speed minimizes the fanning action of the cutterheads and thus reduces the amount of coal fines that become airborne.

Jan 1, 1981

By Klaus Pöllath

The Netherlands RandstadRail project makes use of a large range of sophisticated geotechnical techniques to allow a shield driven tunnel to approach the central station of Rotterdam. This paper describes the construction of three deep excavation pits constructed with 1.2 m and 1.5 m thick diaphragm walls. Besides the presentation of the actual diaphragm wall activities special consideration is given to the break-in and break-out situations of the TBM into the deep excavations pits using sealing blocks and partly glass fibre reinforcement in the diaphragm walls.

Jan 1, 2006

By Wolf-R. Under

For improvement of urban traffic infrastructure, the City of Amsterdam is cur­rently constructing the 9.5 km long North-South Metro line passing through the central districts of Amsterdam. Focal section of the project is the Central Station linking the NS Line with the Central Railway Station, the East Metro line, new bus and tramway terminals, ferries and individual traffic. Construction works required for the project are of high complexity and technical standards. They are executed under severe restrictions concerning programming, space, logistics, and impact on the integrity of existing buildings and structures as all existing installations and facilities have to maintain fully operational during the construction period. The paper deals with the main geotechnical features of the project and in particular with the diaphragm wall and bored pile construction at the Voor-plein and the De Ruijterkade sections of the Central Station.

Jan 1, 2006