Search Documents

By Gordon B. French, Donald E. Garrett

INTRODUCTION Crude oil reserves in the United States are still very large, even though for many years they have not been sufficient to supply our entire domestic requirements. They are continuously being depleted as oil is pumped from the ground, but new discoveries and improved secondary and tertiary recovery methods are helping to reduce the rate of depletion. It is thus a slowly diminishing resource, but even as it is being consumed, immense reserves of oil are left behind as the so called "un-recoverable" portion of petroleum formations. Most oil fields can only obtain a 15 to 40% recovery of the original reservoir, and it is widely quoted that there are still about 300 billion barrels of this un-recoverable oil still in place (Mauch, 1980, etc.). With the present comparatively high oil prices, and the possibility of even higher future prices and short supply, this oil becomes an interesting potential reserve. Mining the petroleum formation would be one means of recovering at least a portion of this oil. The concept of oil mining is neither new nor limited to conventional oil fields, since the procedure could be equally employed with the otherwise difficult to produce heavy oil deposits, and the solid or semi-solid tar sands and diatomaceous hydrocarbon formations. Estimates place the U.S. tar sand resource at about 30 billion barrels, and heavy oil at 5-10 billion barrels (Unitar, 1982). Figure 1 graphically summarizes the heavy oil reserves based upon formation depth and characteristics, while Figure 2 shows their location. It is apparent that the preponderance of reserves are in California and Texas, but that they also occur in many other states. The major companies engaged in oil recovery from the heavy

Jan 1, 1983

The explosion of a charge in a drillhole sets the surrounding rock mass into vibrating stress wave motion. Except in the immediate vicinity of the drillhole, the dynamic stresses associated with this motion do damage only to pre-existing joints, cracks, or other weak planes, not to the rock material in between these. The joints are weak in tension, therefore the damage occurs as a result of tensile stresses. The initial damage process in the rock mass that ultimately breaks loose in front of the hole is similar to that in the remaining rock behind the drillhole. Recorded or calculated values of the vibration velocity and frequency contain a wealth of information about the combination of stress and strain that causes the damage. This paper outlines a new technique by which the peak strain energy derived from measured or calculated vibration velocity records is used to determine the local fragment size distribution. It combines two previously known and well tested techniques, namely the Holmberg-Persson calculation of the peak vibration velocity generated by an extended charge and King's calculations of the fragment size distribution as a function of the strain energy in rock crushing. Both of these calculations are based on experimental data and have been tested and found to agree well with actual conditions in their respective fields. Holmberg-Persson's calculated peak vibration velocities have been used successfully to predict and control damage to the remaining rock in cautious blasting, while King's calculation successfully describes the comminution of rock in mechanical crushing. Preliminary predictions of fragmentation in two types of rock blasting, a large hole open pit mining blast and a tunnel round, indicate that the new technique for fragmentation prediction has the potential for predicting fragment size distributions within the rock removed by the Blast.

Jan 1, 1995

By D. F. VanDine, H. George

"The possibility of spoil pile failure at the Kara Kara bauxite strip mine, Guyana, South America, is of major concern to the mine operators. The current mining technique requires the continuous operation of an 11 ms bucket capacity walking dragline on top of 18 metres of freshly spoiled uncompacted overburden material consisting of varying mixtures of kaolinitic clay and quartzitic sand. A field biased geotechnical study of undisturbed overburden and corresponding spoiled material has identified site-specific, non-linear correlations between vane shear strength, standard penetration resistance and spoil pile composition. Readily available geological exploration borehole logs has enabled a composite clay isopach map of the entire mining property to be drawn and critical areas to be zoned according to expected slope stability. Stability has been assessed using simple hand calculation techniques. Use of the resulting stability map provides the mine operators with a means of forecasting the need for appropriate preventative measures at varying stages of mine development, throughout the life of the mine.A similar investigation procedure could be employed at many presently operating and future strip mines.IntroductionThe Kara Kara bauxite stripe mine is located at Linden within the bauxite belt of Guyana in South America. The mining property covers a total area of 88 hectares of flat to gently sloping ground of which some forty per cent is being actively mined or being preparatorily stripped of overburden, prior to eventual mining (George and Gordon, 1979). The regional climate is tropic and humid. Temperatures vary from 16°C to 38°C and yearly rainfall averages 2600 mm, with at least 55 per cent of this precipitation occurring during the 'wet season' months of May to July and December to January."

Jan 1, 1983

The activiltion of sphalerite with electrolytically generated copper ions from a copper electrode instead of the usual practice of the addition of copper sulphate was studied in the laboratory. A large surface area of copper was provided by lining three sides of a bench flotation cell with copper sheeting. The lining was connected to the positive terminal of a low voltage d.c. source, and the cell impeller to the negative terminal.Sphalerite was effectively activated by this arrangement and was subsequently floated using xanthate as the collector.Flotation results comparable to those obtained with 1 lb/ton CuS04.5H20 (0,255 lb/ton copper) were obtained using 0·1062 lb/ton of electrolytic copper and 0·488 kWh of electrical energy. The wastage of copper due to the formation of insoluble precipitates was found to be dependent on the length of time the current was passed. Maximum current was passed for the shortest time to minimize wastage.

Jan 1, 1973

By D. Jeulin

For iron ore sinters to be good blast furnace burden, they need to possess certain basic properties such as cold mechanical strength, reducibility, etc. Relations between such basic parameters and sintering parameters (composition of the mix, fuel consumption, operating conditions of the sintering plant, etc.) are not always well understood. For example, one cannot explain the differences in quality noticed for sinters having the same chemical composition. In this paper a new approach is proposed for the characterization of iron ore sinters by a quantitative description of their morphology. The Texture Analyzer LEITZ T.A.S. is used for this purpose and such morphological parameters as sizes of microstructures and the size distribution of phases are measured on samples of sinters. The results indicate that these measurements can be correlated with the sinter quality.

Jan 1, 1977

By Luino Jr. Dell'osso, Richard L. Every

The enormity of the methane-in-coal problem is discussed, with a brief summary of the state-of-the-art. Laboratory techniques and data on the desorption of methane from Pittsburgh seam coal are presented and discussed and include the effect of time, temperature and vacuum. Under laboratory conditions, it was possible to displace 90 per cent of the residual methane by flooding the coal samples with carbon dioxide. Carbon dioxide was found to be three times more effective than air and almost five times more effective than helium.

Jan 1, 1972

By K. Ohga, V. J. Hucka

The presence of methane gas in mines creates hazards of explosions, fire and suffocation. Under certain conditions the occurrence of methane also poses a danger of gas and coal outbursts. Consequently, prevention of gas and coal outbursts in coal mines requires a sound knowledge of methane gas occurrence in mine workings. However, the direct method of determining methane content of coals developed by the U.S. Bureau of Mines is time and labor consuming for measurement, a new transportable methane tester was developed for Japanese coal mines. The instrument automatically measures emission gas from coal samples in the underground and also records and stores the data. Back on the surface, the tester can be connected via a RS 232 port to a PC computer for methane content estimation. Details of this technique are described here. Results on methane content determined in Japanese and U.S. western coal seams are discussed, as well.

Jan 1, 1991

By Forrester P. I, Richardson W

Methane in coal mines is an ever present hazard resulting in loss of lives and serious economic consequences. For effective control of methane, ventilation alone may not be totally adequate in some situations. In order to deal with such cases, new methods for the control of methane are being researched. One such method based on biotechnology has been investigated in Canada in the past several years. This method involves bringing methane oxidizing micro- organisms into contact with coal to oxidize the methane released to non-flammable products.

Jan 1, 1988

By B. R. Mohal, S. Chander

"A new technique to determine wettability of powders is presented in this paper. In this technique the times for immersion of individual particles from air into liquids, defined as imbibition times, are measured. Through the measurements of imbibition times for a large number of particles, it is possible to determine homogeneity/heterogeneity of a powder sample with regard to its wetting behavior. Quartz particles give a very narrow distribution of imbibition times showing a homogeneous wetting surface whereas coal particles give a broad distribution indicative of the heterogeneous nature of its surface. The imbibition time measurement technique is considered to have certain advantages over other methods to determine wettability of powders in surfactant solutions. In this study we have also compared the imbibition times with the wetting rate mea¬surements obtained by a modified Walker test.INTRODUCTIONSeveral methods are available for determining wetting characteristics of sol¬ids. Each of the methods has been used in the past to obtain very valuable information for comparing wetting behavior of various solids in a given liquid or for comparing the wetting behavior of several liquids for a given solid. Each method measures a somewhat different aspect of wetting and therefore quantitative correlations between techniques have been difficult. A general approach is to use a method in which close similarity between the technique and the application (where results of wetting measurements are to be used) can be maintained. The objective of this investigation was to develop a method which could be used to determine the wetting characteristics of single particles in surfactant solutions. Wetting of individual particles is of importance in cap¬ture of dust particles by sprays of surfactant solutions.METHODS FOR DETERMINING WETTING — A BRIEF REVIEWThe various methods available for measuring wetting characteristics of solids include: contact angle, immersion/sink time, bubble pick-up, induction time, capillary rise, and displacement method measurements. Some of the methods are briefly reviewed in the paragraphs that follow."

Mar 1, 1989

By B. Dubreuil

Arsenical bearing deposits are posing an increasing challenge for the mining industry. In particular, mineral processing of arsenical sulfidic ores for base and precious metals recovery tend to produce problematic arsenical tailings. This arsenic being present as sulphide or oxide, tends to dissolve, contaminating surface and underground waters. To meet the environmental regulations, it is often required to stabilize the arsenic in a more insoluble form. Nichromet has developed a new patented technology using vitrification of the arsenic oxide in an economical way, giving a stable solid, well below the environmental regulations upon leaching. This technology involves oxidation of As (III) to As (V), by using a low cost natural oxidizer and transformation of the produced arsenic oxide into calcium arsenate, which is not volatile at the melting temperature of the glass. This technology would be advantageously applied on most cases around the world where sulphide concentrates are oxidized in a fluidized bed or smelted.

Aug 1, 2013

By B. Dubreuil, J. -M. Lalancette, D. Lemieux

Arsenical bearing deposits are posing an increasing challenge for the mining industry. In particular, mineral processing of arsenical sulfidic ores for base and precious metals recovery tend to produce problematic arsenical tailings. This arsenic being present as sulphide or oxide, tends to dissolve, contaminating surface and underground waters. To meet the environmental regulations, it is often required to stabilize the arsenic in a more insoluble form. Dundee Sustainable Technologies has developed a new patented technology using vitrification of the arsenic oxide in an economical way, giving a stable solid, well below the environmental regulations upon leaching. This technology involves oxidation of As (III) to As (V), by using a low cost natural oxidizer and transformation of the produced arsenic oxide into calcium arsenate, which is not volatile at the melting temperature of the glass. This technology would be advantageously applied on most cases around the world where sulphide concentrates are oxidized in a fluidized bed or smelted.

Jan 1, 2014

By C. Abbruzzese, F. Vegliò, S. Ubaldini, R. Massidda

The aim of this paper was to study the influence of different water/organic solvent mixtures (isopropyl alcohol, ethanol and ethylene glycol) on the gold desorption process. The experimental work was carried out on laboratory scale, using activated coconut carbon with different temperatures and extraction times, without adding cyanide. Best results have been obtained in this order: isopropyl alcohol > ethylene glycol > ethanol. Starting from gold concentration of about 5 g Au per kg of carbon, best kinetics resulted in 97-100% of gold extraction, after 8 hours of desorption, at a temperature of 80ºC.

Jan 1, 2003

By C. Abbruzzese, F. Vegliò, S. Ubaldini, R. Massidda

"Gold solubilised during cyanidation can be recovered by precipitation (Merrill-Crow process) or by adsorption onto activated carbon, these being the techniques applied in industrial plants.Precious metals (Au, Ag) adsorbed onto activated carbon are extracted during a subsequent stage in aqueous phase, by various technologies, such as hot elution (70-80°C) or under pression desorption (100-130°), with hydro-alcoholic solutions.This stage is of great interest from an economic point of view, due to the high energy costs. Temperature represents the critical kinetic factor.The aim of this paper was to study the influence of different water/organic solvent mixtures (isopropyl alcohol, ethanol and ethylene glycol) on the desorption process.The experimental work was carried out on laboratory scale, using activated coconut carbon with different temperatures and extraction times, without adding cyanide.Best results have been obtained in this order: isopropyl alcohol > ethylene glycol > ethanol. Starting from gold concentration of about 5 g Au per kg of carbon, best kinetics resulted in 97-100% of gold extraction, after 8 hours of desorption, at a temperature of 80ºC."

Jan 1, 2003

By Hideki Yamamoto, Shigeno Matsumoto, Junji Shibata

"Some fundamental studies were carried out in order to produce composite powders comprising of two or three metal oxides ~y using liquid-liquid extraction and to develop the control technology of the particle size. The combination of samarium and cobalt was selected as the two component composite powders. Both stripping and crystallization occurred at the same time by emulsifying the organic phase loading the two metals extracted with Versatic Acid 10 and the aqueous solution containing oxalic acid. The effect of aqueous pH, oxalic acid concentration and agitation speed was examined on some properties such as crystallization percent, particle size and shape of each metal oxide powders obtained in this process. The analysis by using EDX showed that the two metal oxides were distributed uniformly.IntroductionComposite metal and metal oxide powders with high purity are indispensable as industrial materials in the fields of electrical engineering, electronics and metallurgy. It is difficult to mix metal powders or metal oxide powders uniformly for the production of alloy powders. If insoluble metal salts are allowed to collect as crystallization products in the crystallization-stripping process, the conventional melting and crushing process can be avoided. After mixing of the organic phase containing metals in fixed composition, fine metal and metal oxide powders of alloy composition are produced by using a crystallization-stripping method. Versatic Acid 10 and D2EHPA, both acidic extractants, were chosen in this experiment, and the metal oxide powders were produced by using oxalic acid as a crystallization reagent. Mixed metal oxalates containing samarium and cobalt were precipitated from the mixed organic phase containing these metals. Furthermore, the physical properties of the powders, such as particle size, shape and thermal decomposition, were measured in order to evaluate them for industrial purposes."

Jan 1, 2000

By Guy Deschênes

In spite of the wide use of lead compounds to enhance cyanidation of free milling sulphide-bearing gold ores, an industrial control method was only implemented four years ago. This study presents the results of the investigation that led to the development of the on-line control technology. Two free milling sulphide-bearing gold ores and high purity minerals were used to develop and test the concept. The first ore contains 2.8 g/t Au, 6.2% pyrrhotite, 2.1% pyrite 0.6 % arsenopyrite, 0.1% chalcopyrite and 0.1% organic carbon. The second ore contains 10.4 g/t Au, 3.2% pyrite, 0.8% pyrrhotite and 0.38% chalcopyrite. The first ore showed a much higher oxidation rate in the pre-leach than the second one and consumed seven times more cyanide. A relation between the formation of thiosulphate and thiocyanate and the additions of lead nitrate were quantified. The ?reducing power?, a titration with permanganate, predominantly determines the concentration of thiosulphate and thiocyanate in cyanide solution. The relation between the reducing power and the addition of lead nitrate at various concentrations of pyrrhotite and chalcopyrite in the ores was established, providing a monitor/control strategy for lead nitrate addition.

Jan 1, 2006

By M. A. Verhaege, Stanislav S. Naboychenko, Vladimir I. Skorohodov, Olga Yu. Goriaeva

A new technology for the processing of secondary raw materials containing precious and Platinum Group Metals (PGMs) has been designed at the Laboratory of Heavy Metals at USTU. The technology is based on hydrometallurgical processing of the materials followed by sorption separation of the PGMs from the leach solution. Different versions of the technology can be realised depending on the type of processed material but the fundamentals are similar. Some parts of the technology can easily be integrated into existing flowsheets. The stage of sorption removal of platinum and palladium was tested on the site of the Joint Stock Company (JSC) "Uralelectromed" on pilot plant scale. A process was developed to obtain fine gold, silver, platinum and palladium. No waste is produced because all solutions are recycled. There are no gas emissions. Selective sorption of platinum and palladium from silver-containing solutions is possible even if the concentration ratio of silver to PGMs is one thousand to one. Sorption behaviour of the PGMs as a function of the bulk metal concentrations was studied. Recovery of 90-95% of platinum and 70-80% of palladium is possible.

Jan 1, 2000

By J. R. Dartez

The use of CCD (counter current decantat.io;1) thickeners, or; clarifiers, in the gold mining industry is quite common. Although there are a number of technologies in the industry which utilize these types of tanks, the fundamental requirement is to settle leach tailings and eventually separate gold and silver "values" from the "barren" (no values) solution. The thickener separation process varies depending upon the raw ores found in any specific mine. In mines where rudimentary, rocky ores are most common the settling process is fairly straight-forward and uncomplicated. But, for those mines with complex carbonaceous ores, usually identified by high silting, clay components, the ability to monitor and control the settled materials is quite laborious and costly. The task of monitoring and maintaining control of settled residue in clarifiers and thickeners, of any design, is difficult in any industry, but due to the added desire in the gold mining industry of leaching the values from the liquid slurry, the problem is multiplied. Other common activities taking place in the thickeners are exaggerated internal flow rates, settleable solids activity due to rake movement, and the settling activity generated by flocculents being added to the liquid medium. All of this action within the liquid column causes the continual monitoring of the interfaces within the tank close to impossible.

Jan 1, 1993

A New Technology of Applying SLon-2500 Magnetic Separator to Recover Iron Concentrate from Abandoned Tails

Sep 13, 2010

By X. W. Zhang

Mica plate is broadly used in electric industry, production of man-made mica paper plate is in-creasing. The problem coming with is that large quantities of leftover materials unable to be re-cycled are produced during cutting and molding of mica plate productions. The leftover materials are always abandoned as crabs, which not only pollute the environment but also waste our resources. The study intends to find a new measure to decompose and to reuse the mica plate leftover materials so as to create a new production process of mica plate, which is clean and does not produce crabs.

Jan 1, 2014

By G. F. Zhang

Yunnan mineral is a kind of containing Ta-Nb rare earth deposit, the most potential economic valuable element in it is Sc, and raw mineral has 17.0 g/t Sc. Take the character of Sc into account, the key problem in producing scandium chloride molten salt by adaptive technology is how to man-ufacturer anhydrous scandium chloride molten salt. During the course above, the key problem is that preventing Scandium chloride from being hy-drolyzed into ScOCl. The ScOCl content of molten salt not only affect purifying scandium but al-so do harm to the production of Mg-Al alloy. In order to restrain the creation of ScOCl, add ammo-nium chloride into molten salt. As long as ScOCl is created, it would be chloridized. Thus, during the course of dehydrating anhydrous chloride molten salt this method prevents scandium from hydrolyzing. Accordingly, the key phase of this producing course is eliminate ammonium chloride and the surplus crystal water, and the most crucial of it is restrain scandium chloride from being hydrolyzed into ScOCl. This research analyzed the theory that ammonium chloride is trend to be hydrolyzed into ammo-nium chloride, and propose the research scheme of restraining this process from creating ScOCl. The new process of restraining the generating of ScOCl and dehydration for crystal water rare earth chloride is adopted: Inert gas temperature increases rapidly to a certain degree to eliminate ammonium chloride and crystal water. The experimental research were done such as : the temperature of eliminating ammonium chloride and crystal water, amount of ammonium chloride, time, temperature growth speed, influence of inert gas flow toward to scandium percent hydrolysis, whereby, we conclude the optimal process condition in this period: Temperature: 400°C, proportion of oxidized scandium and ammonium chloride is 1:1.5(Proportion of oxidized scandium and additional salt is 1:5.4), time is 120minute, temperature growth speed is 10?/min inert gas flow is 5L/min.

Jan 1, 2014