Search Documents

By Yuting Xue, Khaled Mohamed

The failure of coal ribs is a major hazard in underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have been working on the development of an engineering-based rib control method. A user-friendly standalone application, called Design of Rib Support (DORS), is being developed to ease the calculations of rib support. DORS can estimate the Primary Rib Support Density (PRSD, ton/ft2) for development loading. However, it still needs to take account of another key factor, bolt length, in rib support design. The bolt length can be estimated from the rib fracture depth, and this study focuses on the coal rib fracture depth analysis with numerical modeling and artificial neural network. A total of 331 FLAC3D simulations with different mining scenarios and rib conditions were conducted for this study. Machine learning was then used to predict coal rib fracture depth under different conditions. Based on the numerical simulations, the parameters for mining scenarios and rib conditions were collected as features for machine learning, and coal rib fracture depths were collected as the target to predict. Good data correlation (r-square) was obtained with the use of an artificial neural network. The

By S. B. Bhagwat

Equipment capacities of a sample of Illinois surface coal mines representing about 60% of surface production in the state were studied. Available equipment capacity was compared with the required capacity, as indicated by coal production and stripping ratios reported. Most mines sampled showed surplus equipment capacity, which if avoided, would result in substantial cost savings. The surplus capacity results mostly from market fluctuations that result in underutilization of equipment. Study findings underline the importance of market assessment at the time of mine planning and of communication between marketing and engineering arms of a coal firm.

Jan 1, 1987

By Matthias Schnitzler, Herbert Pfeifer, Ralf Bolling

"To transform metals high temperatures are usually needed. A fast and efficient heating can reduce the C02 emitted. The fastest way to heat metals is called direct flame impingement (DFI). The flame impinges upon the item being heated. For this method it is important to know the shape and length of the flame. Laser-induced fluorescence (LIF) technology allows measurements of a two-dimensional field without influencing the reaction or the flow. Commonly used is the measurement of OH-radicals, an indicator of the reaction zone.In the presented study measurements of a turbulent diffusion flame are shown. The position of the reaction zone and the influence of the distance between the item being heated and the burner are investigated. Conventional measurements and LIP-measurements are compared and the potential of DFI to increase the efficiency of heating metals is discussed.IntroductionDuring industrial heating processes a fast and efficient heating technology is required. Two important aspects are the NOx emission and the energy efficiency. The direct flame impingement (DFI) technology has the highest heat transfer rate possible with a gas/air flame. The turbulent high velocity flame jet impinges upon the item being is heated [ 1]. Due to the high heat transfer rate furnace and exhaust gas temperatures are lower. Therefore the energy efficiency is increased and the amount of NOx emitted is reduced.Hydroxyl- (OH-) radicals are an intermediate product that is generated during the combustion of hydrocarbons [2]. They are commonly considered as an indicator for the reaction zone and position of heat release. Figure 1 shows the hydroxyl-mole fraction in dependence of the distance along the gas flow. The figure clearly shows how fast the OH-concentration increases in the reaction zone. Figure 1 also shows that OH-radicals are present in the post combustion region, however in smaller concentration [3].The laser-induced fluorescence technology serves to measure the spatial distribution of OH-radicals in a two dimensional cross-section area of the flame. Therefore the flame dimensions and location can be determined with high spatial resolution without influencing the flow or the reaction [ 4,5]."

Jan 1, 2012

By M. D. Aldridge

This document reports the results of a two-year research effort aimed at improving communication systems used in coal mines. This work was conducted under a program whose original goal not only involved the development of practical and effective electronic systems for operational communications, but also for monitoring, at a central location, remote instruments at key positions in a mine. About half way through the originally proposed three year effort, the program was redirected to phase out the communication effort at the end of two years and to concentrate the program" resources on the investigation of new monitoring system concepts developed by this research. Thus, the work reported here is incomplete relative to the originally pro- posed program. However, the work was carried to the point of providing sufficient evidence to aid in the comparison of certain new communication concepts. For the concepts chosen for this study, the work was stopped short of hardware development and field testing, Several reports in the form of Master's theses and a Doctoral Dissertation have resulted from this research. They each report in considerable detail the results of several individual" contributions to this program. In preparing this report, an attempt has been made to provide a complete description of the significant results but with- out burdening the reader with the minute details. These more detailed reports are referenced heavily for the convenience of those interested. PRESENT COMMUNICATION METHODS Two types of communication systems are presently used In coal mines. They are: 1, Various forms of telephone systems, and 2. Carrier current radio systems using the trolley line as the interconnection circuit. Carrier current radio is used almost exclusively for control of rail trafflc by the dispatcher. Almost all other communication uses the telephone system, Telephone lines generally extend to areas where trolley lines are not present such as the outside offices and warehouse. Therefore the telephone system provides the primary means of voice communication. Telephones - Telephone systems employed in American coal mines fall into three categories. 1. Paging type telephone systems - these systems have individual stations which use battery powered transistor audio amplifiers to boost signal levels for normal communication. When in the page mode,

By Frank E. Dalton

The Metropolitan Sanitary District of Greater Chicago (MSDGC) serves an area of approximately 860 square miles and collects and processes used water from the city of Chicago and 116 surrounding communities. As a public agency, the MSDGC -Serves a population equivalent to 10 million people which is composed of 5.5 million people and an industrial wasteload equivalent to an additional 4-1/2 million people. -Provides 400 miles of intercepting sewers and tunnels ranging in diameter from 12 inches to 24 feet. -Operates 71 miles of navigable waterways and channels conncecting the Atlantic Ocean and the Great Lakes with the Gulf of Mexico and 6,000 miles of inland waterways. -Maintains the largest water reclamation plant in the world. -Processes 1,380,000,000 of used water daily and removes approximately 1,000 dry tons of organic solids each day. -Has spent approximately 700 million dollars in capital improvements to date, and will require expenditures in excess of 3 billion dollars (including over one-half billion dollars in tunnels) to meet existing federal and state water quality standards.

Jan 1, 1974

By Weller K. R, Trahar W. J

The Mount Lyell Company treats some 2.3 million tonnes of ore annually, mined from a number of orebodies on the field. Blended ore is essentially a quartz-sericite schist containing about eight per cent of pyrite and three per cent of chalcopyrite. Four-stage crushing and two-stage ball milling are followe by selective flotation for copper. Pyrite is recovered from the coarse fraction of dopper circuit tailings. A detailed survey involving examination. of 82 samples provided information on the size- by-size behaviour of the principal ore constituents throughout the grinding, copper flotation and pyrite flotation sections of the circuit. Results for the copper and pyrite flotation sections are presented in the paper, and it is shown that over half the copper reporting to the final tailing (5% of copper in the feed) is plus 100 microns and that the major pyrite loss is in the desliming cyclone overflow. These data proVide a basis for assessing potential methods of circuit optimisation.

Jan 1, 1977

By Y. J. Wang

The use of controlled recirculation began in the early 1930s. Although this method has been applied in many mines since then, a generalized comprehensive network analysis is still lacking. This paper presents a unique approach in which the ventilation network with a controlled district recirculation is divided into two subsystems: a main subsystem and a recirculation subsystem. The subsystems are analyzed individually, and the results and their relationships are then integrated into discussions of the total ventilation system. The analysis of the recirculation subsystem is facilitated by introducing a nondimensional parameter (A), which represents the ratio of the air quantity for the working face to that for the subsystem. As a result, far and regulator pressures and air power for various recirculation arrangements can be effectively expressed as a function of and the subsystem air quantity. Numerical examples are included.

Jan 1, 1997

The Copper Concentrator at Mount Isa Mines Limited treats approximately 6 Mt of chalcopyrite ore annually. The ore is currently sourced from the 1100 and 3000 orebodies at Mount Isa. Chalcopyrite is the only significant copper bearing mineral, with pyrite, quartz and dolomite being major gangue minerals. Ore is typically 10% chalcopyrite, 11% iron sulphides and 79% non-sulphide gangue. Copper ore is treated through two autogenous mills, two ball mills and a flotation circuit. The autogenous mills replaced a crushing plant, two rod mills and two primary ball mills during 1991. For routine analysis of concentrator performance, composite samples of mill feed, final concentrate and tailings are generated every 4 week period. All samples are sized and size fractions are assayed. Recovery of mineral species to the concentrate are then calculated for each size fraction. Sometimes liberation analysis was also performed by QEM*SEM (Quantitative Evaluation of Material by Scanning Electron Microscope).

Jan 1, 1990

By M. Furuta

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. has been operating without a slag cleaning furnace (SCF) since its start-up in 1972. It has used its own developed coke combustion technology, the Tamano-Type Flash Smelting Furnace (T-FSF). The coke combustion technology that is the core of the process, along with the installation of a computer guided system and the improvement of the concentrate burner combustion in the T-FSF have all contributed to having acceptable copper loss levels in the slag without using a SCF. However, recently, because a high concentrate charge rate has been used in order to achieve a high matte grade in the T-FSF, a short settling time has been experienced and copper losses in the slag have become difficult to maintain at a lower level. Furthermore it is estimated that copper losses will further increase after the completion of the next expansion because with the aim of having a higher matte grade operation at 67% less coke will be charged and the reduction effect of the settler will be smaller. Therefore, in order to maintain the copper losses in the slag within proper levels the installation of SCF was decided. This paper, describes the operation before the introduction of SCF along with some theoretical considerations of slag chemistry.

Jan 1, 2006

By A. K. Kyllo

A study has been carried out on the dusts from Hudson Bay Mining and Smelting's Flin Flon copper smelter. The aim of the work was to determine the mechanisms of dust formation and the deportment of the various constituents. The work concentrated on the copper converters, but the electrostatic precipitators and baghouse also clean the reverberatory furnace off gas, so some mixing will have occurred. The dust composition was found to vary with distance from the furnace, and to be made up of three major components: solidified droplets, unreacted flux, and condensed particles. The solidified droplets were formed from material ejected from the converter during blowing, while the flux was blown out of the converters immediately after charging. The condensed particles contained the majority of the lead and zinc, as well as the volatile impurities. There was also a significant soluble content of the dusts, increasing with distance from the furnace. The condensed material may be separated from the remainder by a simple washing and sizing technique.

Jan 1, 1996

By Claude R. Ayoub, Charles A. Kliche, David G. McDowall

Homestake Mining Company's Open Cut Mine is located in Lead, South Dakota, in the northern Black Hills. The mine is within 300 feet of occupied residences on the south end, and within 1200 feet on the north end. Mining began at the north end of the open pit in October, 1983, and blasting related complaints began almost immediately. Noise and ground movement comprised the majority of the structural damage claims. As a result of these complaints, Homestake purchased a recording seismograph and began monitoring nearly every blast. In addition, the company hired a consultant to review Homestake's blasting and monitoring practices. He was also asked to do a single, one-time study of the cracks in six homes. This initial work led to Homestake monitoring all blasts with three seismographs and having South Dakota School of Mines and Technology do a year-long study of crack development and propagation in five homes in Lead.

Jan 1, 1989

By Washington Martins da Silva Júnior

In stamping process, sliding between metal sheet and forming tool leads to wear of tool surface. Maintenance of stamping tools involves polishing the tool edge, or, in case of severe damage, replacement of the tool. Hard coatings have been applied on the stamping tool surfaces in order to reduce the maintenance cost causing a great economic impact in metal work industry. In this work, CrAlSiN coatings were applied by PVD onto SRV2W tool steel. The coating toughness was avaliated by the critical load in scratch tests. The following coating parameters were analyzed: 1- substrate surface finishing process; 2- coating architecture (multilayer or gradient); 3- chemical composition of the coating. AlSi concentration varied from the substrate/coating interface to the surface. Coatings were 3 µm thick. Scratch tests were carried out using a Vickers indenter. The applied normal load was varied from 0 to 13 N for a scratch length of 5 mm. In order to study the effect in the toughness, the substrate roughness was controlled by the finishing process before PVD coating. Samples subjected to polishing presented highest critical loads. Gradient coatings presented higher critical loads than those with a multilayer architecture. Coatings with higher concentration of AlSi near the surface supported higher loads before failure.

Jul 31, 2018

By R. Yi

The determination of the optimum cutoff grade for a surface mine may be very different from that of an underground mine because a selectable mining method may be used in the latter case. A review of research into the theory of cutoff grade is made and then a new method, based on Optimal Control Theory, is presented. This method uses a Hamiltonian function to assist in obtaining the solution. It is shown that the life of a mine can be divided into three parts: a beginning period bf planning before mining; an intermediate period when both an average price and market information are used continually to adjust the cutoff grade; and, a final period when the main consideration is the current market situation.

Jan 1, 1987

By Mikko Ahola

This paper describes recent innovative analyses conducted by the Bureau of Mines to demonstrate the application of the boundary-element method in evaluating the effectiveness of caving chambers or sacrificial entries to relieve the stress conditions initiating cutter roof failure in underground coal mines. The analysis assumes that cutter roof failure results when the shear strength of the roof rock at an entry corner is exceeded by the applied shear stress. The applied shear stress is due to large differences between the horizontal and vertical in situ stresses known to exist in many coal mining districts experiencing cutter roof failure. The results of boundary-element analysis suggest that driving an arched lead entry in advance of adjacent rectangular entries and allowing it to cave significantly reduces the difference between the principal stresses at the corner of the rectangular entry, thereby lowering the maximum shear stress. Slippage of the immediate roof along horizontal bedding planes into the caved entry is shown to further reduce the stress conditions in adjacent entries. Practical applications of this stress control technique to longwall and room-and-pillar mining are discussed.

Jan 1, 1987

By A. Wahab Khair

Coal mining has evolved into extensive use of continuous mining machines for development and production. This has resulted in an increase in dependence on the versatile continuous miners. The present-day continuous miners are powerful in terms of rated power but are still plagued by wear of bits which hinders development and production as the bits have to be continuously changed at regular intervals. Previous attempts to analyze bit wear has been either restricted to the theoretical approach and or laboratory testing. This paper discusses about the overall aspect of bit and drum design for different conditions. Using the laboratory model set up, numerical models and field testing, a new bit and drum design was analyzed to evaluate their performance under different conditions. The results proved that a newer bit design and drum design were successful in limiting the amount of wear as well as improving the performance of the continuous miner and production.

Jan 1, 2008

By Jason Baird, Braden Lusk, Dominique Nolan, Allen Stults

Conical shaped charges have been used to penetrate rock for many years now. Examinations have been made looking at shaped charge liner geometry, material, and standoff, as well as explosive composition, confinement and initiation. Most of the testing conducted towards penetration rather than cratering has fallen within the realm of the petroleum industry and as such been confined to specific rock types, with test apparatus that include simulated down hole (subterranean) environments. The testing conducted within this experimentation is conducted at ground level, in small scale samples, using a single standoff, against multiple rock types. The data collected from that testing is examined here and relationships between physical properties of the rock and the liner are analyzed. The analysis of that data raises the possibility of a relationship that may lead to new empirical methods of penetration prediction in rock.

Jan 1, 2012

By I. Cotman

Dimensional stone processing has become an important part of the world extractive industry, and today?s total stone block yearly production is estimated to be around 134.000.000 tons and is still growing by an average yearly rate of approximately 20%. In future, the same production will become an important part of the mining industry and presently, in some countries it represents even the main mining output. New environmental regulations, together with landscape and nature conservation requirements, create a number of difficulties in setting up new open pit dimensional stone quarries. As a result, many dimensional stone producers have recently started to apply underground techniques in order to produce the ornamental stone blocks intended for further processing. Underground production of stone blocks requires special mining methods and so far it has not been a cost-effective excavation method for all types of rocks. Presently, this type of stone excavation is generally applied in sedimentary and marble deposits because the rock has small to no mineral quartz content. When starting a new underground dimensional stone mine, it is necessary to analyse the impact of all primary factors which are crucial to set up a technically and cost effective advanced underground dimensional stone mine. The role of physical and mechanical properties of the rock, geological conditions, mineralogical composition, micro-tectonic state of the site, rock mechanic conditions on the site, durability and saw ability of the stone are decisive factors in foreseeing the future methods of extraction. The laboratory research work as well as the field work, is very important in decision-making aimed to choose the future excavation method. Also of equal importance is the serious market research, because it renders the indication of selling price potential. Having obtained the results from both types of research, mining engineers can design the mining methods which optimize financial return to the mine. The practice approved by 15 years of testing in the underground limestone quarry of Kanfanar gives future producers very useful advice and general data to facilitate the process of exploration intended to establish new similar underground quarries.

Aug 1, 2013

By J. A. L. Napier

Computer programs which rely on the assumption of linear, elastic rockmass behaviour have been used routinely for many years in the South African mining industry to determine the stresses arising in the vicinity of mining excavations. A description is given of the theoretical background and novel solution techniques used in the recently developed MINSIM-D boundary element program. Features of the program include the ability to analyse multiple interacting reef planes at arbitrary orientation to one another, slippage on fault planes and the effects of backfill placement in mined areas. Incremental mining sequences can be modelled, and digitizer and front-end routines have been written to assist in the capture of mining outlines and general problem specifications. A brief indication is given of design problems for which MINSIM-D is appropriate, as well as some future extensions of the system.

Jan 1, 1987

By Shi Yuan

Molten copper was deoxidized using a one-end-closed yttria-stabilized zirconia (YSZ) tube. A thin layer of porous Ni-Zr02 cermet electrode was deposited on the inner wall of the YSZ tube. The outer surface of the tube was in contact with the melt and the inner surface with a flowing reducing gas. Without applying external EMF, the melt was deoxidized by short-circuiting the melt with the cermet electrode. The deoxidation process was analyzed and the rate controlling steps were identified. These experiments were also conducted at different temperatures to evaluate the effect of temperature on the deoxidation kinetics.

Jan 1, 1994

By M. Karfakis, K. Kim, R. V. de la Cruz

The in situ deformability of a closely jointed basalt rock mass was determined by two different methods: the NX-borehole jack method where displacements of opposing curved platens were related to applied hydraulic pressures, and the modified Goodman jack method where tangential strains on the borehole walls were related to induced tangential stresses. The modulus obtained by the modified Goodman jack method were much higher than those obtained by the NX-borehole jack method. To explain the discrepancy, the influence of fractures and test variables, such as depth, orientation, hole location, and applied pressure on the calculated modulus of the rock mass, were analyzed by factorial analysis. It was found that the orientations and measurement depths have statistically significant effects. The in situ deformability values obtained by nonlinear regression analysis were also found comparable with other measurements and empirically predicted values for the basalt rock mass.

Jan 1, 1984