Search Documents

By Shuo Zhang, Wenying Liu

"In dump leaching, the efficiency of metal extraction from ores is strongly influenced by the mechanisms of fluid flow. Particle size distribution acts as a fundamental parameter in the determination of fluid flow properties in packed ore beds. In this study, we investigated the particle size distribution in dump leaching by using image analysis technique. The results showed that the particles in the dump varied from smaller than 2 cm to larger than 200 cm in diameter. P80 was calculated to be 200 cm, which was significantly higher than the historical data used by the operation. P25, P50 and P80 were found to increase non-linearly with increasing depth towards the toe of the dump, suggesting the segregation of fine and coarse particles. The image analysis results were verified by applying the rock fragmentation models. The model with the Swebrec function was found to be in better agreement with the image analysis results. Future research will investigate the effect of particle size distribution on the behaviour of fluid flow.INTRODUCTION Fluid flow plays an essential role in the extraction of valuable metals using heap/dump leaching (Amos et al., 2009). The rates of the chemical leaching reactions and microbial activities determine metal concentrations in the leachates and therefore the efficiency of the metal extraction. The reaction rates are influenced by two fundamental processes: transport phenomenon and reaction kinetics (Bouffard & Dixon, 2001). The transport phenomenon refers to the percolation of fluids through channels and pores in a packed ore bed, which carries lixiviants and reaction products to/from ore surfaces by convection and diffusion. The percolation rate of the leaching solution is determined by the hydraulic conductivity of the packed ore bed, which is a function of the permeability and the degree of saturation (Guzman et al., 2008). Permeability, an intrinsic property of a packed ore bed, is strongly influenced by the particle size distribution of the ore grains (Bouffard & Dixon, 2001). Hence, the objective of this study was to investigate the particle size distribution in dump leaching."

Jan 1, 2017

The National Institute for Occupational Safety and Health (NIOSH) has continued study of the Personal Dust Monitor (PDM) developed by Rupprecht & Patashnick Co. Inc. through a CDC contract and currently being commercialized by Thermo Fisher Scientific. This report examines the effect of oversize particles, cyclone inversion, and cleaning procedures. Clean and exposed filters were examined using light microscopy and particulates counted before and after various instrument manipulations. The data presented show that the dry cleaning procedures do not cause significant (greater than limit of detection) sample contamination by respirable or oversize particulates and that the cyclone is resistant to particulate carry over during inversion.

Jan 1, 2009

By H. F. Yancey

THE jig may be termed the standard coal-washing machine. Although exact figures on the relative tonnages of coal treated by the various coal-cleaning processes are not available, it is known that a large part of all the coal given special cleaning treatment is handled by jigs. This wide use of the jig warrants a special study of its performance. In this paper are presented the results of an analysis of work done by a three-compartment jig in treating bituminous coal from the Thick Freeport bed in Allegheny County, Pa. Certain systems of washing coal require sizing before washing, while others treat unsized coal. The prevailing practice, however, for the preparation of coking coal from the more easily washed coal is to treat an unsized or natural feed at about -1 in. size and smaller. Under such conditions, the minimum size of particle that is beneficiated has long been and is still a matter of discussion and conjecture. In a careful laboratory investigation Jüngst1 concluded that the practical limit of settling of fine coal is reached at from 0.02 to 0.008 in. On the other hand, Hancock2 has found that single-compartment jigs, used in preparing coal for the domestic market, usually allow most of the heavy (refuse) particles smaller than 1/4 in. to go into the washed coal. He also states that it is impossible with the ordinary coal jig to make any noticeable improvement in the quality of the coal finer than 20 mesh (about 1/30 in.). Because of its importance in coal cleaning, the work described in this paper was undertaken for the purpose of obtaining information on this subject, as a part of the general coal beneficiation program being carried out by the Bureau of Mines.

Jan 4, 1925

By James Lee Hibbard, Doraiswami Ramkrishna

A population balance model accounting for the transient variations in drop size distributions in a stirred liquid-liquid system is analyzed for its effect on chemical reaction conversion in a stirred, batch reactor. The analysis is applied specifically for phase transfer catalytic reactions, which indicates that transient effects of evolution of drop size distributions may be important in such systems.

Jan 1, 1981

By Lijun Xu, Jan M. Mutmansky

The purpose of this research was to investigate airborne coal mine dust characteristics in order to assess the possibility of contribution of these characteristics to the incidence of coal workers' pneumoconiosis (CWP). The characteristics studied included physical (mass concentration and size distribution), chemical (elemental composition), and mineralogical (quartz and kaolinite content) variables of the dust. The results are based primarily upon analysis of the characteristics of 99 impactor samples from 18 mines in seven states. Because the eight stages of the impactor span the range of dust sizes up to 20 microns, the characteristics analyzed should represent respirable dust characteristics well and also provide size-dependent representations of the characteristics. In general, the patterns of mass concentration and size distribution in the various mines studied were similar with mass concentrations being high downwind of the continuous miner. The concentrations and size distributions were more variable upwind of the continuous miner, apparently as a result of the variations in the dust conditions in the working section. Significant size effects on the elemental and mineralogical content are shown in the data. Concentrations of most of the elements decrease as size decreases. However, minerals content increases as the dust size decreases. Regional variations of elemental and mineralogical content are also significant. Quartz and kaolinite contents are small in regions with low incidences of CWP. However, the elements of Cu and Zn are high by comparison to their content in high-incidence coal fields and may have the effect of protecting against the disease.

Jan 1, 1991

By Jeremy G. Kress

We propose the discrete element method (DEM) as a complimentary alternative to analytical solutions and FEM models for the analysis of pile response. DEM is a novel approach to the engineering design of deep foundations which can be used to provide insight into the mechanics of soil-soil and soil-structure interaction. It is common to use analytical, empirical, and semi-empirical methods to predict pile behavior, where if granular properties, pile length, or load orientation change, then significant adjustments are made in the design sequence. DEM provides a more uniform approach in granular soils. Based on constitutive force-displacement relationships and laws of motion in rigid and elastic bodies, few changes must be made for a wide variety grain types, pile types, embedment, and load orientation. Preliminary results for simulation of a single pile are qualitatively consistent with results from conventional design procedures and also provide significant information not available from other analyses (e.g., local information about interface failure during shear). Importantly, these analyses are portable to a variety of pile types and installation procedures, which may not be the case for empirical approaches. Given consistent increases in computing power and rapid advances in model speed and sophistication, the DEM should prove to be a robust method for design and the analysis of pile response in granular soils.

Jan 1, 2010

By Sudip Basack

"The topic of pile foundation subjected to lateral cyclic load is an age-old problem confronted by Geotechnical Engineers. The environment prevalent in ocean and shorelines necessitates the piles supporting offshore and onshore structures to be designed accounting for the lateral cyclic loading resulting from the effects of sea waves. The quasi-static nature of this type of loading induces remarkable deterioration in the interactive performance of the soil-pile system. This can be manifested as progressive loss in pile capacity associated with increased pile head deflection. The work reported herein is aimed towards conducting rigorous theoretical analysis using finite difference technique so as to analyze the lateral cyclic loading response of a single, vertical pile embedded in cohesionless soil. The theoretical results are compared with the experimental results and reasonably good agreement is noted. This paper presents a brief description of the theoretical analysis carried out with some typical results and the relevant conclusions drawn therefrom. 1. INTRODUCTIONOffshore structures, namely, quay & harbour structures, jetties, tension leg platforms, oil drilling platforms, etc. are largely supported on pile foundations. Apart from usual loads from superstructures, these piles are subjected to continuous action of wave loading. This type of lateral loading is quasi-static cyclic in nature which results in considerable degradation in the interactive performance of the pile-soil system initiating progressive reduction in pile capacity associated with increased pile-soil stiffness. This may ultimately lead to disastrous consequences.Amongst limited research works in this field, the major contributions are made by Matlock (1970), Idriss et al (1978), Poulos (1982), Vucetic et al (1988), Long & Venneste (1994) and Basack (1999). A brief review of these works indicates that the degradation of the pile-soil system under lateral cyclic loading mainly depends upon the following parameters: number of cycles, frequency (cycles per unit time), cyclic load level (ratio of cyclic load amplitude to the lateral static ultimate pile capacity, in case of loadcontrolled mode) and cyclic displacement level (ratio of cyclic displacement amplitude applied at the pile head to the external pile diameter, in case of displacement-controlled mode). As pointed out by Poulos (1981 & 1982), the degradation is mainly due to: 1) partial to zero dissipation of excess pore water pressure generated during cyclic loading in progress, 2) destruction of interparticle bond with particle realignment and 3) rearrangement and gradual accumulation of permanent plastic deformation around pile"

Jan 1, 2005

By Gandhi

Piled raft foundation under uniformly distributed vertical loads has been analyzed using Finite Element Method. The soil is considered to be linear elastic, isotropic, homogeneous. The raft,pile and the soil have been idealized with eight noded brick elements. Parametric study have been carried out varying pile length, soil modulus, raft thickness, and pile spacing. Design charts have been produced to achieve 50% load sharing between pile and raft for optimum design. Data available in literature is compared with the design chart results and found satisfactory.

Jan 1, 1996

By JO Choi

Jet-grouting method is a useful technique to reinforce foundations on relatively soft or vulnerable soil layers such as fractured zone and stratum with cavities. Although jet-grouting has been widely applied to various field works, a reliable design standard has not been established yet. A number of model tests were performed to investigate end bearing behaviors of piles reinforced by jet-grouting. It was concluded that end bearing capacity was increased in proportion to uniaxial compressive strength of grout column. Based on the test results, the design criteria for the end bearing capacity were suggested.

Jan 1, 2006

By A. T. Iannacchione

Underground mining of stone in the US is increasing, as is the depth of overburden above the mines. Data gathered from mine visits, maps, discussion with operators and numerical simulation have been used to investigate pillar design and recommend safe practice. Many pillars have slender shapes with relatively large adjacent mine openings: width-to-height ratios range from 0.54 to 3.13 and extraction ratios from 0.56 to 0.91. The pillar material is often very strong and average overburden only 80 m, but occasional failure due to excessive local stress has occurred where pillar size had been unintentionally reduced, overburdens were greater than 200 m, width-to-height ratios were less than 1.25 or extraction ratios were greater than 0.83. Pillars with width-to-height ratios of less than 1.5 appear more likely to fail under excessive stress. When width-to-height ratios fall below 1.0, defects such as through-running discontinuities can have a significant influence on stability. Dip, orientation and material properties are also important

Jun 21, 1905

By A. T. Iannacchione

Synopsis Underground stone mining Is an emerging sector of the U.S. mining industry. As this expansion takes mines under deeper cover, and as more efficient mining methods are utilized, effective stone pillar design methods will become even more Important. Current design practices are examined and a discussion of safe mine layouts is presented as a first approach towards weighing the demands for increased production against increased risk. Risks to underground stone-mine workers include rib Instabilities, pillar failures and roof falls. Seventy-two stone-mine pillar designs were examined. Pillars with width to height ratios of less than 1.5 appear more likely to fail when subjected to excessive stress levels. When width to height ratios fall below 1.0 defects in the pillars, such as through-running discon¬tinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties and orientation are also important determining factors in pillar strength. During the past three years the number of active underground stone mines in the U.S.A. has ranged between 90 and 100. This number is expected to increase as the crushed stone industry responds to growing demands for its products.1 As more of the industry moves to benefit from the advantages of underground mining production from underground stone mines is expected to increase above its current level of approximately 66 000 000 r/year. Parker2 identified four advantages of underground mining operations: (1) surface developments, zoning laws and environmental concerns are often less of an issue; (2) stripping and restoration requirements are eliminated; (3) additional reserves are often available beneath the quarry floor, under pit slopes or under an adjoining property; and (4) space is created for secondary use. Underground mines enjoy the added benefits of work in a constant underground climate, rather than in the variable surface climate, minimization of community concerns by placement of the crushing, sizing and stowing operations underground and reduction of surface vibration concerns through smaller blasts. The drawbacks of underground mining include added health and safety hazards for the stone miners, whose health can suffer from increased exposure to falls of ground, airborne contaminants and fog in large underground openings. Injuries from falls of ground in stone mines have occasionally exceeded the incidence rates for other mineral resources mined underground. 3 Existing underground stone operations, by comparison with stone operations a decade ago, mine more stone at a faster rate and with larger equipment. Because of high demand mines face increased pressure to yield more stone per production blast. A majority of the miners use the V-cut blasting pattern, which limits the depth or pull for each shot to about 4 m. Therefore, to produce more stone, either the mines must work more faces or existing faces must be enlarged. The enlargement of underground openings poses problems in the maintenance o€ strata stability, First, the widths of the mine entries partially control the amount of sag or deflection that any given roof beam can withstand before failure. This deflection can take pi ace quickly after an opening is excavated or much later as weathering processes form additional, thinner beams. Because increased deflection increases the potential for roof beam failure, there is a limit to how wide a room can safely be made. These limits depend on local geological and stress conditions and, to some extent, the cost effectiveness of roof-bolting. Given these room width limitations, underground stone mines have placed more attention on expansion of production through benching where mining thicknesses permit. The heights of rooms partially control the strength characteristics of adjacent pillars: as the room height increases for a given pillar width the pillar width-to-height ratio (w/h) decreases. In general, stone pillars are very strong, but when the width-to height ratio diminishes the potential for pillar rib instabilities and pillar failures increases (see Fig. 1). [ ] In the underground environment the desire to utilize wider rooms, higher benches and multi-level mining results in the potential for unstable ground conditions. Although the number of failed pillars is currently very low, the potential for additional failures will grow if more slender pillars are developed, especially under deeper cover, with wider mining sections and in multi-level operations. It should also be noted that the passage of time acts to decrease the strength of many existing pillars. An examination of current design practices

By Sangseom Jeong, Moonkyung Chung, Junyoung Ko

"Abstract The plugging effect of open-ended piles in sandy soil is analyzed by full-scale field test and plugging measurement. PLR (plug length ratio) measurement data from 144 field cases are analyzed with pile diameter. Based on the plugging measurements, PLR of open-ended piles which have above 1000mm diameter is predicted to be above 0.9. Through plugging measurements, a new empirical method is suggested for quantifying the plugging effect of open-ended piles. The proposed PLR equation is possible to predict the behavior of soil plug in the preliminary design stage. In addition, in order to investigate the behavior of the soil plug of open-ended pile, field load tests are performed on instrumented three piles driven into sand. It is obtained that the resistance components of open-ended pile are separated by double-walled pile system. It is found that inner shaft capacity is developed nearby pile tip. However, upper soil plug did not influence the inner shaft capacity. Also, it is found that all test piles are floating piles and unplugged condition because the sum of inner shaft capacity and outer shaft capacity is calculated about 58 to 76% of the ultimate bearing capacity.INTRODUCTIONIn Korea, a number of huge construction projects such as harbor terminals, offshore grand bridges, and lifeline systems are progress in urban and costal area. In these areas, steel pipe piles are frequently used to support high-rise buildings and heavy weight structures for ensuring structural safety rather than serviceability limit capacity. Also, steel pipe piles are frequently used in civil engineering structures because they have many advantages such as high-load bearing capacity, light weight and outstanding workability. The mega foundations of grand bridges and high-rise buildings are required in geotechnical engineering. Large diameter driven piles are frequently used in several projects.Many specifications such as API, FHWA and AASHTO have been reported as a design guideline of plugging effect, however , the current design method for plugging effect of steel pipe piles are mainly based on the our knowledge derived from observation of the model test or the small diameter pile load test. Therefore, these specifications have limitation to apply the large diameter steel pipe piles.Much work has been done to study the plugging effect by many researchers. Yamahara (1964) reported that soil plug has been modeled as a thin disk element as shown in Figure 1, since the increment of radial strain of the soil plug can be neglected due to high rigidity of the pile compared to that of the soil plug. Klos and Tejchman (1977) reported that the end bearing capacity of open-ended piles was almost equal to that of a closed-ended pile when penetration depth of pile was above 15times the pile diameters by model tests. Paikowsky and Whitman(1990) reported fundamental studies on mechanism of plugging effect in sand. Paik et al. (2003) reported that empirical relations for plug load capacity, annulus load capacity, and shaft load capacity of open-ended piles are proposed based on the model pile tests. As discussed above, much work has been done in the area of plugging effect. But little work has been done to study the plugging effect by full scale field tests."

Jan 1, 2014

By S. Kelebek, E. Yalcin

"Diethylenetriamine (DETA) and/or triethylenetetramine (TETA) are reagents that can generally be categorized under ""flotation modifiers"". These polyamines are known to be effective for the deactivation/depression of pyrrhotite that is present in Canadian nickel-copper sulphide ores in large quantities. Recent bench scale testing on some of these complex ores indicated that chalcopyrite flotation can also be adversely affected under certain conditions involving polyamines, which may be taken to be an evidence of their specific affinity towards chalcopyrite. In general, DETA shows no significant depressant action on chalcopyrite while TETA's promotion of hydrophilicity for this mineral has been observed even in the presence of xanthate. This prompted an investigation on thermodynamic equilibria involving these polyamines and copper ions. Results serve a useful purpose to identify conditions for deactivation phenomena. CuDETA2+ and CuTETA2+ chelates as products of sequestration have large predominance areas covering a wide range of redox and pH conditions, where copper xanthate species are not stable, especially in the presence of TETA."

Jan 1, 2009

By C. B. Piazzarollo

Red Ceramic materials are widely used in Civil Construction in Tropical Countries. However, these materials have high porosity and low mechanical strength. Thus, in order to improve these properties, recycle mineral wastes was incorporated into clay from Campos - RJ, ornamental rock waste, from the gneisses cutting of Cachoeiro - ES, 150 km from Campos. After the addition of up 10% of waste in clay mass, ceramic pieces were produced and subjected to the tests of porosity (P) and flexural strength (FS). The test material contains 53.3% clay and 67% waste slit. The X-ray diffraction identified the presence of kaolinite, quartz and feldspar for the clay and, for the waste, quartz and orthoclase. The results of FS and P showed that the residue influenced, positively, the ceramic piece, with strength gains especially from 920º up to 960°C.

Jan 1, 2015

By Jones IO, Coles A, Austin D

This research project came about as a result of ICI Australia offering a scholarship to a final-year mining engineering student at the Western Australian School of Mines. A signifi-cant part of this year of study is devoted to an industrial project and consequently one of the conditions of the award is that the successful applicant pursue a research project of interest to the donor company.Having selected the project and the most appropriate final year student, a steering committee composed of representatives of ICI Australia, Kalgoorlie Mining Associates, the Mines Department and the WA School of Mines was set up. This committee is largely responsible for planning the main thrust of the research work whilst the detailed planning and day-to-day activities have been largely the responsi-bility of the research student, his academic supervisor and senior staff at the Mt Charlotte Mine.

Jan 1, 1984

By Edouard Masengo

A long dyke will be constructed in a lake with rockfill placed by end dumping method. Its crest will be at elevation 521.5 m compared to the nominal lake level at 520 m. In the first portion, its height will vary from 1.5 m on a 35.1 m thick tailings layer to 18.3 m on about 0.5 m of tailings. In the second portion, the dyke will be built on native silty clay and will vary from 18.3 to 15.2 m in height. The tailings consist in stratified layers of fine-grained soils showing lateral and vertical segregation. The tailings are compressible and may develop excess pore water pressure on loading. The tailings overlie a thin layer of relatively soft native silty clay. The till beneath the silty clay is considered incompressible compared to the material above. After construction, as the tailings and silty clay consolidate, pore water pressures will dissipate and dyke stability will improve. Since dyke stability will increase with time, the primary concern is its stability during construction. As a result of construction activities, three potential modes of failure were identified and recommendations were provided regarding the measures that should be undertaken to increase dyke stability during construction.

May 1, 2003

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

"The work in the paper introduces a 2-dimensional finite element model for analyzing particular material processing in a roller press. Two basic roller geometries are considered: (a) smooth rolls (used for milling and compaction) and (b) rolls with cavities, commonly used for briquetting. A model is presented that is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables.MODEL, RESULTS AND CONCLUSIONSAn associated Gurson model was employed as a constitutive model for the material. The calibration of the model was based on experimental results from an instrumented compaction die. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Powder River Basin sub bituminous coal fines with moisture content 9% was used as a model material.Two finite element models have been set up, one for the briquetting roll and one for the “equivalent” flat roll. Approximately 3200 plain strain continuum elements with reduced integration (CPE4R) were used. Lagrangian-Eulerian (ALE) approach in conjunction with judiciously applied remeshing was employed with the commercially-available, dynamic explicit version of ABAQUS finite element code.Comparison of model predictions with experiment shows that there is an agreement in terms of the general trends of experimental values recorded on laboratory roller presses. Gurson model overpredicts stresses at low densities and, as a consequence, overpredicts roll force and roll torque."

Jan 1, 2003

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

Roller presses are widely utilized in mineral industry for fine milling and compaction. Recently used models are providing only limited information about the material behavior in the roll bite. This paper introduces a 2-dimensional finite element model for analyzing those two basic processes. A pressure-dependent plasticity model with linear elasticity was used as a constitutive model for the particular material. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Two basic roller geometries are considered: smooth (used for milling and compaction) and with cavities, commonly used for briquetting. Comparison of the results obtained from the model with experiment indicates that they are following the general trends of experimental values recorded with laboratory roller presses. It is shown, that the model is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables. This allows the process engineer to gain an improved understanding, leading to a better process and equipment design and control.

Jan 1, 2003

By B. K. Mishra

Power draw of the mill has been accepted as an indicator of the performance of the mill, yet the problem of predicting power under a given set of mill operating conditions still remains to be solved. In the literature, this problem of predicting power is attributed to a lack of knowledge with regard to the motion of the charge. Here a DEM based model is used to analyze the motion of the charge. The resulting information is used to predict the power draw of the mill. A 16-ft diameter mill is simulated. A factorial design study of the variables-mill speed, lifter configuration and ball size distribution-as independent variables is taken up. The power draw as a response variable is analyzed to establish the best operating condition of the mill.

Jan 1, 1993

By R. Karl Zipf, Suresh Bhatt

Highwall mining is an important coal mining method. It appears that upwards of 60 highwall miners are presently in operation, and they may account for approximately 4% of total U.S. coal production. A review of the Mines Safety and Health Administration (MSHA) data over the 20 year period from 1983 to 2002 identified 9 fatalities attributable to auger and highwall mining of which inadequate ground control accounted for 1/3. In the past 5 years, 1 fatality occurred in highwall mining. Estimates of the manpower requirements in highwall mining suggest that its fatality rate is essentially the same as for surface coal mining, thus highwall mining appears to be a very safe modern mining method. Highwall stability is the major ground control related safety concern, and operators are required to develop and follow an appropriate highwall mining ground control plan. The plans usually specify the following geotechnical parameters: hole width, maximum hole depth, maximum overburden depth, seam thickness, web pillar width, barrier pillar width and number of holes between barriers. Calculated web pillar stability factor exceeded 1.3 for most designs evaluated. This study examined records from 5,289 highwall miner holes with a total completed footage of about 2,560,000 feet to understand the reasons for early pull out. Average lost footage is typically about 20% of planned footage. Only 35% of the holes reached planned depth, and 20% were short due to rockfalls. Water and adverse geology accounted for 15% of the losses. Mechanical/electrical problems, guidance, and slope stability problems accounted for the remaining 30%. Web pillar stability factor for these holes also exceeded 1.3 in 95% of cases. Best practices to avoid trapped miners include: avoid mining in stream valleys, avoid mining near outside corners, careful alignment of each hole and the use of an onboard guidance system. Several issues in highwall mining ground control require further investigation including highwall mining through old auger workings, highwall mining near old underground mines, multiple-seam and multiple lift highwall mining and finally the size and frequency of barrier pillars.