Search Documents

By Edoardo Misano, Magali Schivre, Martino Semeraro, Alain Bochon

"INTRODUCTIONThe Laboratoire Souterrain de Modane (LSM) is an underground research laboratory located in the Western Alps on the French – Italian border. It is located in the middle of the 13km long Fréjus highway tunnel that links Modane (France) to Bardonecchia (Italy) in correspondence of the highest overburden of 1800m. The LSM current activity is mainly based on the investigations about the dark matter and requires very sensitive instrumentation which shall be protected from cosmic rays. To comply with the new legislation about safety in tunnels, the highway tunnels owners agreed in 2007 the construction of a parallel safety tunnel, at an average distance of 50m from the existing tunnel and the laboratory owner CNRS (Centre National de recherche scientifique) also decided to extend the existing laboratory with the construction of a new 17000 m3 cavern allowing the installation of wider and more powerful instruments that could increase chances of success of research. Preliminary studies stated that, considering both geological and functional issues, the most appropriate location for the new laboratory shall be in between the two tunnels and parallel to the existing laboratory (see Figure 1).Hence, the CNRS asked Systra, already in charge of the works supervision of the safety tunnel, to realize the design of the new cavern. The laboratory extension includes the construction of a 40 m long cavern with 300 m² cross section and two smaller tunnels connecting the safety tunnel and the existing laboratory to the new cavern. The minimum distance between the front face of the new LSM and the highway tunnel is about 25 m.The French and the Italian authorities, responsible of the exploitation of the Fréjus highway tunnel, asked the CNRS to develop an accurate study indicating that the construction of the laboratory extension would not have any negative impact on the existing structures of the highway tunnel. The main results of the developed study by Systra are summarized hereafter. The construction works should begin prior to the end of the construction works of the Fréjus safety tunnel in 2018."

Jan 1, 2016

By A. Shakoor, T. P. Gautam

The long-term slaking behavior of clay-bearing rocks in the field can be quite different than the short-term slaking behavior in the laboratory. To assess this difference, 12 replicate samples of each of 20 clay-bearing rocks, including 5 claystones, 5 mudstones, 5 siltstones, and 5 shales, were exposed to natural climatic conditions for 12 months. After each month of exposure, one replicate sample of each rock was removed from natural exposure and its grain size distribution was determined. Disintegration ratio (DR), defined as the ratio of the area under the grain size distribution curve of the slaked material for a given rock to the total area encompassing all grain size distribution curves of the tested samples, was used to quantify the amount of disintegration under natural climatic conditions. DR values of naturally exposed samples were then compared with the corresponding values of second-cycle slake durability index (Id2) determined in the laboratory. The relationship between Id2 and DR after, 1 month of exposure, exhibits an R2 value of 0.65 but the relationship deteriorates when DR values for 6 and 12 months of exposure are used, with R2 values of 0.63 and 0.25, respectively. However, when DR values for laboratory samples, computed from grain size distributions of slaked material after second cycle, are compared with DR values of naturally exposed samples for the three periods of exposure, the relationship improves with the corresponding R2 values being 0.61, 0.71, and 0.41. These results suggest that DR may be a better parameter for assessing the long-term disintegration behavior of clay-bearing rocks than Id2.

Jan 1, 2015

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (see Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By F. Crundwell, A. J. Lathwood

A number of base-metal operations would like to increase production to take advantage of the higher metals prices. In general, this higher production should not be achieved with major operating changes. In hydrometallurgical facilities, leaching and pressure leaching represents one area where upfront limitations may be a bottleneck to the capacity of the entire plant. An assessment of the capacity of the leaching tanks and autoclaves was performed using a predictive model within the AweSym flowsheet simulator. The model is described, and the results of the application of the model to a number of different leaching reactors are presented. It is argued that the leaching number, which relates the residence time, particle size and the leaching rate, is of prime importance. Finally it is shown that there are some unexpected catastrophic events in increasing production capacity without a thorough understanding of the leaching operation.

Jan 1, 2007

By Jan E. Nesset, Colin Hardie, Peter Radziszewski, Donald P. Leroux

"The successful introduction of new high intensity stirred milling technologies (e.g. IsaMill, SMDetritor) to the mining industry in recent years prompted Noranda-Falconbridge to initiate a study comparing these technologies to the conventional technologies of ball milling and existing vertical stirred mills (e.g. VertiMill). The study was unique in that it utilized the same material (Brunswick Mine zinc cleaner regrind mill feed), the same sizing instrument (a Malvern laser difractometer) and sampling protocol, and media size and type (for the high intensity stirred mills). The paper compares the net energy efficiency (kWh/t) of the various technologies, their power intensity (kW/m3) and product size distribution spread (P80/P20). A key finding is that media size is critical to achieving optimal performance. As part of the performance comparison, an analysis of the four methods of power measurement was made (Prony brake, shaft torque, grinding chamber reaction torque, “no-load” correction) and followed-up with an experimental test procedure using three of these methods. The findings include divergent results for power measurements and some explanations based on the observations are proposed. The direct shaft torque and Prony brake calibration methods are shown to be the methods most suitable for stirred mills.INTRODUCTIONThe motivation for the investigation reported here was the lack of a suitable comparison within the available literature of relative grinding efficiency for the emerging crop of new industrial fine grinding technologies. Such comparisons are potentially fraught with inconsistency, from ore samples and grinding media used, to testing methodology, to size measurement techniques, to the power measurements themselves. The collaboration of the industrial suppliers (at the time MIM Technologies and Svedala, now Xstrada Technologies and Metso Minerals) and McGill University (P. Radsiszewski) were sought in order to ensure as valid a comparison as possible. The work was performed between October 2000 and November 2002, led by the mineral processing group at the Noranda Technology Centre (NTC) in Pointe-Claire, Quebec. The paper is presented in two sections; Part A considers the different power measurement methods and a comparison of the results for the SMDetritor (SMD) technology, while Part B reviews the grinding performance of the 5 technologies investigated using the selected performance criteria."

Jan 1, 2006

The quality of iron ore fines in terms of high iron content and low levels of deleterious impurities such as Silica, Alumina, Sulphur and Phosphorous is a critical parameter, in sintering and subsequent iron and steel making processes. As the higher-grade ores become depleted, there will be a stronger focus on treating lower-grade haematite/goethite ores and developing suitable beneficiation techniques to reduce the levels of impurities. Innovative flow sheets, based on new and commercially available technologies, is required. These will be needed to include gravity concentration devices, which can handle coarse and fine feed sizes. In this paper, efforts made to reduce the silica and alumina content of a low grade iron ore fines (<1.0 mm size) sample from the Pilbara region in Western Australia are described. The feed sample, a goethite abundant lower grade iron ore fines, which was a plant reject assaying 48.66% Fe with 13.61% SiO2and 5.09% Al2O3 was investigated. To this end, an experimental campaign was undertaken, and beneficiation studies were conducted on the sample using a Floatex Density Separator (FDS), a gravity device which can be operated for size classification and/or relative density separation. The objective was to produce high-quality iron ore material suitable as sinter feed. An iron concentrate with a grade around 57.0% Fe (Calcined Fe of about 63.0%) was achieved while recovering around 67.0% of the feed weight. In addition, a rejection of substantial content of Silica (>75%) and Alumina (>66%) was achieved while securing >77% iron recovery. On the other hand, sharp classification efficiency with low values of imperfection around 0.20 was obtained. Consequently, the response of the lower grade iron ore sample to FDS application, has vast potential to reject deleterious impurities as a single stage separating beneficiation equipment. Remarkably, it was demonstrated, that a great amount of goethite, abundant in lower grade iron ore fines/plant rejects, which are currently being either stockpiled and/or dumped as waste, can be treated using FDS application and potentially can add a significant value to the iron ore mining industry by recovering additional iron ore fines. Keywords: deleterious impurities, beneficiation techniques, classification, relative density separation

Sep 1, 2012

It is possible to divide industrial minerals into four general categories: 1. fuels, 2. construction&nbsp;materials, 4. agricultural minerals, and 4. industrial minerals. It is proposed to ignore the fuels in the context of this paper and deal in general terms with the others. Mining companies have often considered getting into the industrial mineral business because they can see a resource development with good growth and consistent profits. However, many mining companies being conversant with the metallic side of the industry have spent sleepless nights determining which industrial minerals are most suited for their particular situation. Some have got into the business for the wrong reasons and wished they had never heard of it. Others have successfully adapted to the industrial minerals philosophy and now operate in both metallic and industrial mineral arenas. There is a large difference between firstly, the philosophy and secondly, the functions of being in the industrial minerals business as opposed to metallicÆs. The philosophies can be considered in parallel but it is necessary to clearly have an appreciation of the dominant influences that affect industrial minerals.

Jan 1, 1984

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

Incident investigation is of utmost importance in most high-risk industries and is often used to improve organisational safety. This study was undertaken to examine the content of past incident investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of five elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of three Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed.

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

Incident investigation is of utmost importance in most high-risk industries and is often used to improve organisational safety. This study was undertaken to examine the content of past incident investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of five elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of three Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed.

By E. Stemn

Incident investigation is of utmost importance in most high-risk industries. This study was undertaken to study the content of past investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of 5 elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of 3 Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed. INTRODUCTION The importance of learning from incidents is well documented in the literature. For instance, some scholars regard learning from incidents as important for improving safety [1,2]. Thus, many organisations spend considerable resources in identifying lessons from incidents and subsequently on the process of improvement that follows the identification of lessons. It is therefore important for such organisations to determine the effectiveness of their learning from incidents processes, in order to identify specific areas where improvements are needed, so that interventions can be as specific as possible. The learning from incidents process models the plan-act-check-do approach of management systems, often consisting of four major stages, namely; data collection and incident analysis, planning interventions, implementing interventions and follow-ups and evaluation [3,2]. The investigating and analysis of incidents have been regarded as one of the vital stages of the learning process since it is the stage where lessons are identified [3,2,4]. It has also been noted elsewhere in the literature that results of the previous stage of the learning process are important for the next stage [3]. For example, ineffective incident analyses could result in the planning of ineffective remedial measures. One of the primary aims of incident investigations is to identify lessons from previous incidents which when implemented can prevent future recurrences or minimise the effects of future incidents. There is thus the need for organisations to assess the quality of their investigations periodically since it is one of the means they adopt to improve safety and the quality of remedial measures to some extent depends on the effectiveness of the investigations. Although previous studies [5,2] have assessed the effectiveness of the learning process, and some aspects of the learning process, such as incidents reporting, there is less focus on the effectiveness of incident investigations. The research described in this paper was therefore conducted to contribute to this gap, focusing more closely on incident investigation reports.

Jan 1, 2019

By R. A. Leveille, M. D. Doggett

"Economic returns for the copper industry have been assessed by building cash flow models for each of the 100 new mines brought into production over the past 20 years. Ninety-one of the 100 new mines returned the assumed 8% cost of capital and generated a positive net present value (NPV) at the development decision point. Economic criteria for individual mines are highly variable with NPV ranging from -$111 million (-$111M) to +$3850M (all money values are presented in United States dollars) and internal rate of return (IRR) ranging from -8% to +95%. The copper industry collectively would generate approximately $39 billion dollars in NPV through the development of the 100 new mines.The returns to exploration ($174M per deposit) were measured by deducting the cost of exploration per deposit ($221M) from the returns to development per deposit ($395M). Overall, the copper business has provided positive returns to exploration. However, the variability in returns across deposits means that only 41 of the 100 new mines can carry the average cost of exploration. The long lead times and high costs associated with exploration result in only those deposits with large amounts of contained copper being able to cover the average finding cost of the industry.The returns to development and exploration are shown to be highly sensitive to the cost of capital and metal price assumptions. With respect to deposit type, porphyry deposits are both larger (NPV) and exhibit lower profitability (IRR) than the nonporphyry deposits. On a geographic basis, returns to development and exploration are higher in Chile than elsewhere, reflecting the larger average deposit size and lower average exploration cost per deposit."

Jan 1, 2009

By Jepsen L, Gifford M, Thomas G. S

Mine planning requires careful prediction of both the head grade and tonnage of mineralisation. As part of the planning process, operators of the Murrin Murrin nickel/cobalt orebodies (located in the Eastern Goldfields province of the Yilgarn

Jan 1, 1998

By Gochin RJ

This paper focuses on measures of the economic significance of mineral exploitation and processing activities, such as beneficiation, refining and smelting. Empirical measures are suggested to quantify the relevance of the degree processing within a nation&apos;s mineral industry. The most useful, based on the input-output econometric framework, are used to establish the magnitude of links between the mineral industry and its satellite activities and for the appraisal of large, non-marginal projects. The input-output impact analysis is refined to allow for country specific behaviour and synthetic indices for the appraisal of investments in the mineral sector are developed. These indices are further improved with the introduction of shadow prices to incorporate socio-economic issues. They are useful to direct mineral policy decisions and several investments towards the most promising objectives for national goals. Finally traditional methods for the appraisal of small scale, marginal, mineral projects are assessed where local impact and regional development issues are more relevant than national ones.

Jan 1, 1993

By S. Ata, Y. Pan, S. Gautam, G. Bournival

Bubbles play a vital role in flotation, and their properties directly affect the flotation performance. Xanthates are one of the major collectors used in sulphide mineral flotation. It is often believed that their main function is to render the desired mineral surface hydrophobic, which is essential for the mineral particles to attach to air bubbles. This paper takes a systematic approach to assess the influence of potassium amyl xanthate (PAX) at the air–liquid phase and its interaction with the frother in the concentration of range 10–5×104 ppm. Bubble size was measured in a laboratory flotation cell using a photographic technique and the stability of bubbles was quantified in terms of coalescence time -, the time required for a bubble pair produced at adjacent capillaries to merge into a single bubble. Bubble size reduction of up to 26% was observed with increasing PAX concentration in the cell. The bubble coalescence experiments using PAX only showed that the bubbles coalesced quickly at lower concentrations (10–50 ppm), but they stayed extremely stable at higher concentrations (1×102–1×104 ppm). Further experiments were carried out where the concentration of PAX was fixed at 1 ppm and 4- Methyl-2-pentanol (MIBC) concentration was varied. The synergetic action of PAX and MIBC significantly improved the stability of bubbles in the mixed system, and is even compatible with a stronger frother. The results strongly suggest that the role of PAX at the air–liquid phase should be considered in the practice of sulphide flotation. Keywords: Bubble size, bubble coalescence, PAX, bubble stability

Jan 1, 2020

By C. L. Kosmoski

The mining industry faces many workplace hazards that are a threat to human health and safety. The Bureau of Labor Statistics has found that employees in coal mining are more likely to be killed or sustain an injury or illness than workers in private industry. These injuries are also likely to be more severe (Bureau of Labor Statistics, 2007). In recent years, coal mining injuries have attained national attention due to highly publicized disasters. Despite these threats to worker safety and health, the U.S. relies on the mining of coal to meet its need for electrical power, with42% of electricity in the U.S. generated through the burning of coal (U.S. Energy Information Administration, 2012b; United Mine Workers of America, n.d.). Furthermore, the production of coal continues to increase and reach record levels every year(National Mining Association, 2012; U.S. Energy Information Administration, 2012a). For this reason, the coal mining industry must continue to find ways to protect its workers while maintaining productivity. One potential approach to protecting workers while maintaining productivity is through improving the safety culture at coal mines. In order to achieve this culture, operators, employees, the inspectorate, etc. must share a fundamental commitment to safety as a value. This type of culture is known in other industries as a ?safety culture? and can be defined as the characteristics of the work environment, such as the norms, rules, and common understandings that influence facility personnel?s perceptions of the importance that the organization places on safety. Fundamental to improving safety culture within an organization is understanding the existing safety culture; improvements cannot be made without first elucidating areas that require improvement. This manuscript details the process undertaken by researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) to assess the safety culture at five underground coal mines across the United States. The purpose of this manuscript is to introduce the mining industry to a multi-methodological approach to safety culture assessments. Further, it is the goal of this manuscript to highlight the value of including both quantitative and qualitative methods into safety culture assessments in order to obtain the most comprehensive view of an organization?s safety culture. Because this manuscript focuses solely on the methodology implemented, data and results obtained during the five safety culture assessments will not be presented in this manuscript, but will appear in a future publication.

Feb 27, 2013

By C. L. Kosmoski

In recent years, coal mining safety has attained national attention due to several highly publicized disasters. Despite these threats to worker safety and health, the U.S. relies on the mining of coal to meet its need for electrical power, with 42% of electricity in the U.S. generated through the burning of coal (U.S. Energy Information Administration, 2012b; United Mine Workers of America, n.d.). Furthermore, the production of coal continues to increase and reach record levels every year (National Mining Association, 2012; U.S. Energy Information Administration, 2012a). For this reason, the coal mining industry must continue to find ways to protect its workers while maintaining productivity. One potential approach to protecting workers while maintaining productivity is through improving the safety culture at coal mines. In order to achieve this culture, operators, employees, the inspectorate, etc. must share a fundamental commitment to safety as a value. This type of culture is known in other industries as a ?safety culture,? and can be defined as the characteristics of the work environment (such as the norms, rules, and common understandings) that influence facility personnel?s perceptions of the importance that the organization places on safety. Fundamental to improving safety culture within an organization is understanding the existing safety culture; improvements cannot be made without first elucidating areas that require improvement. This manuscript details the process undertaken by researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) to assess the safety culture at five underground coal mines across the United States. The purpose of this manuscript is to present the aggregated results from those five safety culture assessments conducted at underground coal mines. Additionally, some general recommendations for areas where coal mines might focus their attention as part of their attempts to improve safety culture are offered.

Feb 23, 2014

By Camilo Uribe, Williams Calderón, Gonzalo Montes-Atenas

In industrial hydrometallurgical operations, the leaching process is often implemented via heap or dump leaching operations. During the pile up of these massive amounts particles a porous material is then formed. The manner it is constructed is crucial since it will define the permeability and other parameters determining the flowrate of leaching solution across the material. This study aims to estimate how the unsaturated permeability of the staked porous structure confined in a column-like geometry varies with and without particle size segregation. The piling up will be modeled using the Rocky® software. Different disposals of particle size distributions across the column will be simulated and their effect onto the overall column unsaturated permeability will be estimated. It was found that when the belt speed increased, the particle segregation in the column also increased. This condition is expected to improve the permeability of the porous structure in the column, probably due to the smaller compaction of larger particles when they are located at the base of the column and maintain a suitable porosity to permit leaching flowrates relatively high, suggesting better extraction results. The opposite was observed when small particles were preferentially located at the bottom of the column. These results are expected to provide an insight towards what is the best way to construct heaps and dumps.

Jan 1, 2014

By B. Genc, V. J. Mahadeo, S. Ramparsad4, U. Govender

The study was intent on assessing the socio-economic impact of a zinc mine in South Africa through the application of people-centric digital tools using a case study research methodology. The global mining industry is undergoing significant technological shifts to modernize, improve operational sustainability, and align with the environmental, social, and governance (ESG) agenda. While the case study mine is a more modernized mine, continuous improvement around the ‘social’ pillar becomes critical, and to this end application of people-centered digital tools presented as the vehicle to understand community needs and impacts. Despite considerable annual corporate social investment by mines annually, the overall impact or social return on investment is marginally understood. Towards contributing to addressing this gap, digital ESG ‘social-related’ data gathering tools for mines decision-making were developed, including the training-needs assessment tool, community-social needs assessment, small, micro, and medium enterprise (SMME) communications and engagement tool, digital leadership competencies gap assessment tool, and change management blueprint, which further allowed for customization to the mining context. Hence, the novelty of this paper relates to applying digital tools to provide real-time information of the needs of a community, both socially and economically. The findings suggested that these digital tools enabled gathering of information for the establishment of regional and operational baselines towards enabling of social investment returns in relation to socio-economic transformation development interventions. These tools have been applied to a zinc mine context, with lessons and experiences obtained through this study, invaluable to the application of these digital tool in other mines in South Africa. The study was conducted in September 2023 across five host communities, surrounding the zinc mine, in the Northern Cape region, with 120 participants involved in the application of three relevant community-related digital tools, which included the training needs, community-social needs, and SMME communications and engagement tools. It was evident that the digital ESG tools could be used for data gathering for the mine’s informed decision-making and allowed for securing of insights on community needs in near real-time, and further proved practical for community use.

Dec 11, 2024

By Andrea Koschinsky, Luise Heinrich, Stefan Gößling-Reisemann

"Germany, like several other countries, has entered a contract with the International Seabed Authority (ISA) to explore the prospects of commercial manganese nodule mining in the Clarion-Clipperton Zone (CCZ). Ensuring a maximally sustainable deep-sea mining operation requires a thorough understanding of the environmental impacts associated with every step of the mining process from the extraction of the nodules at the seafloor to the refinery on land. Against this background, the project presented here applies a combination of scenario-building and life cycle assessment (LCA) to assess and evaluate the sustainability performance of the individual process steps as well as the entire mining operation.Life cycle assessment (LCA) is a comprehensive methodological framework that allows the identification and quantification of impacts occurring during a products life-cycle, as well as the analysis and evaluation of their contribution to pre-defined impact categories, such as climate change, acidification and toxicity (Rebitzer et al., 2004). Until now, LCAs with a focus on raw material extraction have almost exclusively been applied to terrestrial processes. Noteworthy exceptions are offshore drilling, offshore wind farms and ocean fishing. Hence, the first part of the project is to investigate in how far LCA can be applied to deep-sea settings and if and in what way it could be adapted to be used in a deep-sea mining context."

Jan 1, 2017