Search Documents

By Stephen C. Tadolini, Anand Bhagwat

"Intrinsic supports installed in mines with limited seam or mining heights have always proven to be difficult when the required support length is longer. To date, three solutions have been used to ensure that the correct length bolt is installed to achieve the required anchorage or to maintain immediate roof material: combination bolts, milled-notch bolts, and hot-notch bolts. The combination bolts use threaded sections and couples, which can be screwed together to form the required length. The primary bolt of choice, to minimize costs and achieve the desired support, has been milled- or hot-notch rebar bolts. These notches can be placed at strategic (required) locations along the bolt axis, so the bolt can be successfully bent and straightened during the installation process. However, these notches can reduce the strength of the bolting system; special reductions are detailed in ASTM F432-13 (2013). Technical advances in steel rolling and forged heading processes have led to the development of a deformed rebar bolt termed, the BORE bolt, which stands for Bendable Oval REbar. The BORE bolt can be bent at any location and straightened during the bolt installation cycle. This support exceeds the minimum designed capacities described in ASTM F432-13 and meets the yield and tensile strength requirements of a full diameter no. 6 rebar bolt. The profile and shape also reduces the resin annulus during the installation process to enhance mixing and shreds the cartridge film to help eliminate glove fingering.INTRODUCTIONThe height or depth of competent strata material, in the immediate mine roof, can be greater than the developed mine openings heights. This is especially true in coal mine openings where 50% of the minable seams in the US are less than 50 inches (132 cm). When this scenario occurs, it can be difficult to insert steel bolts in a solid single length. Figure 1 illustrates what difficulties can be experienced when a roof bolter operator is working and supporting a thin seam coal mine. There are three viable options currently available. Lengths of the bolt can be threaded and a steel coupler can be used between the sections to reach the required depth of anchorage. These systems, called “coupled bolts,” usually require a larger diameter hole to facilitate the larger coupler diameter and can be anchored with an expansion shell, resin, or a combination of both. To ensure that the coupler will develop the tensile capacity of the bolting system, required by ASTM 432-13 Standard Specifications for Roof and Rock Bolts and Accessories (2013), the threaded bars should be completely rotated and engaged into the coupler. Premature failures can occur when the threads “strip out” if not inserted completely."

Jan 1, 2018

Much of the data required for the evaluation of mine design is obtained from bore cores. It is essential to collect data that is useful and not to overlook features which might have adverse effects upon the mining practices and which might not be readily discernible to the untrained eye when examining bore cores. Interpretation of the data has progressed from the use of single-value properties, such as ultimate compressive strength or Young's modulus, to the utilisation of most measurable quantities. The simulation techniques used employ physical and mathematical models for prediction of mining conditions or strata behaviour. The application and capabilities of these methods to mine design are discussed.

Jan 1, 1977

The paper outlines the development and objectives of the slim core (50 mm dia.) testing procedures employed at the Company's Central Research Laboratories with particular reference to washability studies required for coalfield evaluation. It shows that when the routine test procedures, that have been developed for cores recovered form the Sydney Coal Basin, were applied to Bowen Basin Coals some of the washing data obtained appeared to be suspect. Though yield indications appeared to be of the right order, product ash, required separating gravity and percentage of near gravity material were found to be at variance with bulk washability data. The results of a correlation study made on an underground seam from the Bowen Basin comparing slim core, hulk sample, and pilot plant washing data are given. The results of a series of studies including washability studies made on slim cores, strip samples, large diameter cores and bulk samples, pilot washing trials and computer simulations of washery circuits treating Lilyvale seam coal from the Bowen Basin are shown.

Jan 1, 1977

By Nuno Cruz, Saúl Rodríguez

"When executing offshore bored piles there are several specific factors and problems to consider in order to guarantee excavation stability. One of the methods employed to carry out this type of work consists in setting up a floating work platform, typically a barge, and implementing a soil stabilization system that combines a partial steel guiding casing with third generation polymeric drilling fluids. The main aspects to take into consideration when performing offshore pile boring works are soil stabilization, project design, work methodology and operational aspects. An example of a work methodology problem arises before any pile boring work takes place as the steel guiding casing contains water, sometimes salt water. What to do with this water in order to replace it by an adequate polymer fluid will determine the stabilization capacity as soon as the shaft advances below the protection of the casing. Another example of operational problem may derive from barge movements while executing boring activities. This study is the result of extensive field data collection and concrete logging analysis from marine projects using polymers in different continents. The bored pile stability target was set ranging between 2% to 15% of concrete overbreak. Values above 15% or below 2% mean that there is a stability problem. Then the off-target pile’s data is collected, analyzed and classified under categories. Thus, a direct correlation is established between the problem category and the final results. Modifying steps in the pre-established construction methods or operational variables guarantees target results without the need to replace the approved construction methods. As a general conclusion, the worldwide experience in large diameter marine works, allows to provide truthful information and solutions for these problems. In knowing how to follow a logical sequence of work and applying adequate work methodology will be the key for success.GENERALBackgroundTo carry out the drilling process of offshore bored piles there are two main options to take into consideration: drilling the pile by using full guiding casing until final depth; or using a combined system of partial steel guiding casing and support drilling fluids.The knowledge and situations described in this paper come from the experience acquired in different projects where the second method was employed. This construction method consists in installing a steel guiding casing by vibration and thus covering the water table and further stabilizing the soil below it with polymeric fluids until reaching the pile’s final depth. The Fig. 1 schematic shows an example of this method where H corresponds to the length of the steel guiding casing whereas the remainder of the shaft’s length is stabilized by polymer fluid. The entire bored length is full of slurry up to top of casing.In most cases this kind of civil works results from the need to build a bridge or executing port structures in places where the creation of temporary artificial peninsulas with fill material is impracticable or not allowed. Hence the need to use floating work platforms, commonly referred to as barges."

Jan 1, 2017

By W. E. Coughlin, R. L. Faverty, F. H. Lightner

The intent of this paper is to present the general strategy and method of implementation to achieve a "fast-track" mine development. The major objectives of a "fast-track or rapid development schedule are to minimize front-end development expenditures and to realize an early cash flow from operations. The Borealis project of Houston International Minerals Corp. (HIMCO) is used as the working example to illustrate the development schedule. Borealis is a 2.9 kt/d (2,500 stpd) gold-silver heap leach operation near Hawthorne, NV.

Jan 1, 1984

By Stanley W. Ivosevic

The commercial success of this low-grade property by Houston Oil and Minerals Corp. (succeeded in interest by Houston International Minerals, Inc.) resulted from credibility of analytical data furnished by the property vendor upon initial examination and from other favorable geologic criteria in evidence; from negotiation of lease terms not detrimental to project economics; from entrepreneurial exploration management; from an encouraging attitude by the US Forest Service; and from the favorable mining and metallurgical characteristics of the ore body. The potential of the property, but not its location, was brought to the attention of the project manager (the author) by the vendor some time before accepting employment with HO&M. In December, 1977, the vendor granted an examination to the project manager, by then an employee; and a lease to the 15 mining claims embracing the property was executed in April, 1978. (See Fig. 1.) Field work and extensive claim staking in this virgin district commenced in May, with drilling beginning in August. At the point that an apparent discovery was recognized in October, only $98,000-including property payments-had been expended on the project. By April, 1979, the deposit was drilled out on 60-m (200-ft) centers and a preliminary re- serve estimate, discounted cash-flow analysis, and recommendations for mine development and additional exploration submitted to management-all at a cost well below budget. The property was recommended for acquisition after matching favorable geologic criteria developed by the project manager. Favorable lithology, structure, and geochemical zonation converged on a subdued low-temperature hydrothermal alteration zone subtly expressed on a pediment surrounding the heart of the property, from which approx [ ]

Jan 1, 1985

By Seth K. Martin, Tony Nichlany, Alan R. Poeppel, Konstantinos Syngros

"This paper presents a case study on bored pile construction in challenging karst conditions below a supertall building in Kuala Lumpur. Innovative design and construction techniques helped keep the project moving through very difficult and unpredictable geological and drilling conditions. The development encompasses about 12,400 square meters and includes a 77-story tower, a 59-story tower, a five-story podium, and four contiguous basement levels. The site is underlain by a residual soil derived from a siltstone/claystone (the Kenny Hill formation), then limestone bedrock. Subsurface conditions are relatively uniform within the Kenny Hill and highly variable at the limestone surface. Extreme cases included 40-meter-tall underground caverns, 40-meter-tall pinnacles, and a 50-meter-tall underground rock ledge. Local piling practice in Kuala Lumpur involves deriving pile capacity entirely in the Kenny Hill formation to avoid the unpredictable limestone surface. However, the massive tower foundation loads and relatively shallow bedrock required the piles to be socketed in the limestone. The 77-story tower will be supported by 2.0- and 2.2-meter-diameter bored piles 50 to 100+ meters long, socketed in limestone, with working loads between 40 and 70 Meganewtons. Two Osterberg-cell load tests were used to develop a site-specific rock socket skin friction correlation with RQD. Exploratory rock probes were drilled at each pile location to design the rock socket length based on the rock quality and sloping rock conditions. The rock mass was pressure-grouted during each rock probe to improve the rock quality and fill voids in the rock.INTRODUCTIONThe Kuala Lumpur City Centre, home of the Petronas Towers and the world’s deepest foundations, will be the future home of a new supertall tower. The 77-story tower will be supported by a piled-raft foundation that relies on piles terminating in the highly erratic, karstic Kuala Lumpur limestone formation. The high building loads coupled with relatively shallow limestone across the majority of the tower footprint forced the piles to extend into the limestone."

Jan 1, 2016

By Bolestaw A. Ktosihski

Preloading of bored pile bases by grouting is an effective way of reducing foundation costs. The bearing performance of a pile may be considerably improved. Various techniques and devices are used. Preloading of a pile base by a special grouting installation is preferred. The grouting device consisting of a U-shaped grouting tube with sleeves and a plastic membrane, separating the tube from the pile concrete, has well proven in Polish practice. The preloading may raise the pile design loads by as much as 30%, and increase their stiffness by 50%, in suitable conditions. The preloading equalizes the deformability of piles in a foundation or a structure. Examples of the base preloading use and load tests of base grouted piles are presented.

Jan 1, 2006

By P Marlow

Raiseboring is an attractive method of constructing shafts, being safe, fast and comparatively cheap. But this means back-reaming through weathered ground. However in the gravels and weathered near-surface rocks typical of the Western Australian goldfields, back reaming large diameter shafts through to the surface is risky and conventional sinking from surface has normally been required.An alternative construction approach has recently been used to stabilise the weak surficial materials and allow raiseboring through to the surface. The method is based on first installing rings of non-contiguous reinforced bored piles around the shaft perimeter, for temporary support, then back reaming shafts at full diameter through to the surface. Immediately after the reaming head is removed, the weak exposed materials are supported using remotely sprayed fibrecrete.The method has been successfully applied to four shafts since July 2007; 3 m and 4 m diameter shafts at Trident Mine, a 3 m diameter shaft at Wattle Dam and a 4.5 m diameter shaft at Athena Mine.Bored pile layout designs have varied from eight to 24 piles, of diameters 120 to 270 mm, in one or two rings. In one case, the top 10 m of the proposed shaft was pregrouted. Subsequent surveys have confirmed that fallout occurred in some shafts, out to the ring of piles, implying that the piles inhibited collapse.The practical implementation of the method was not always easy and many valuable lessons have been learnt. This paper documents key aspects of the method and the critical elements for its application.

Mar 21, 2011

By Keat Chuan Chew, Qiao Yue Tung, Teoh Yaw Poh

"1 INTRODUCTION With a land area of 718 square kilometres housing a population of slightly over 5.4 million, as of 2014 (Department of Statistics Singapore 2015), Singapore is a highly urbanised city. Transport infrastructure is critical to keep the country and economy highly connected and functional as the population in Singapore continues to grow. The importance of a robust transport infrastructure is recognised by the Ministry of Transport in Singapore, which is working towards bringing 8 in 10 households within a 10-minute walk of a train station by 2030 (Ministry of Transport 2015). This gives rise to the rapid expansion of the rail network in highly urbanised Singapore, resulting in more tunnelling work having to be carried out in closer proximity to existing buildings. Such tunnelling work is expectedly more challenging and complex, and if not managed effectively, will impose higher risk to the adjacent buildings. Hence, the Building and Construction Authority (BCA) has implemented specific control measures to mitigate such tunnelling risks and to ensure safety of the public. 2 CHALLENGES FACED BY TUNNELLING WORK IN SINGAPORE 2.1 General Challenges of Tunnelling in Singapore With the increasing densification of the rail network in a highly urbanised setting, rail projects in Singapore are faced with several key challenges. One such construction challenge is constrained construction sites brought about by network intensification. Alongside the growth of the rail network, shown in Figure 1, other infrastructure networks in Singapore are also continuously growing. Underground interchange stations between networks become increasingly common, forcing each underground interchange station to be constructed deeper and in closer proximity to existing buildings (Figure 2). Singapore is not alone in facing this issue. The same can be observed in cities like London, in which its myriad network of subway lines pushes new lines and interchange stations to be constructed deeper."

Jan 1, 2016

By George A. Savanick

The objective of this paper is to review advances in the art of borehole (slurry) mining made by the Bureau of Mines. The introduction gives historical and general background information on borehole mining. The borehole mining concept is defined and justified in terms of economics, health and safety, the environment, and resource conservation. This is followed by a description of the design of a prototype borehole mining tool (BMT) developed by the Bureau of Mines. Included are design drawings and performance specifications. The next section describes the application of the BMT in the extraction of metallurgical coal from steeply pitching seams near Wilkeson, Wash., during 1975-76. The field test showed that the BMT produced coal at the rate of 8 tons per hour (tph) (7,272 kg/hr) from a depth of 88 feet (26.8 m) and was effective in producing coal as far as 15 feet (4.6 m) from the center of the borehole. The data are used as a basis for an economic analysis of borehole coal mining and for the suggestions for the design of a second-generation borehole coal mining tool. The following section describes Bureau efforts in applying borehole mining to the extraction of uraniferous sandstone at Rocky Mountain Energy Corp.'s Nine-Mile Lake site, Natrona County, Wyo. BMT design changes appropriate to uranium mining are described along with production, reliability, and reclamation data taken during 1977-73. The field test revealed that the BMT produced 900 tons (81.8x105 g) of uraniferous sand at an average race of 8 tph (7,272 kg/hr) from a depth of 75 (22.8 m) to 90 (27.4 m) feet and created a cavity 25 feet (7.6 m) in radius. These data are used as the basis for an economic analysis of borehole mining of shallow uraniferous sandstones. Reclamation data included will be the results of backfilling experiments conducted at Nine-Mile Lake during 1978. The most significant of these data were that backfill was emplaced at the rate of 16 tph (14.5x103 kg/hr) and that 90 percent of the material extracted from a cavity can be backfilled.

Jan 1, 1979

By Barber C, Buselli G

Detailed monitoring of point sources of groundwater pollution is expensive due to the high cost of drilling monitoring boreholes. Whether groundwater pollution is due to mining, industrial or domestic waste disposal, a universal difficulty when monitoring groundwater contamination is the placement of boreholes to adequately define the extent of the pollution plume. This paper reports groundwater 'resistivity variations determined from transient electromagnetic soundings at a domestic waste disposal site north of Perth in Western Australia. Together with available hydrogeological and water quality data, the geophysics provides a broad "plume scale" picture of groundwater contamination. A simple three dimensional model of plume development, which takes account of the dimensions of the wastes, has also been developed and shows good agreement with the spread of contamination indicated by the geophysics for relatively small values of the dispersivities. Better estimates of these parameters are still required. The work indicates that a combination of geophysics and modelling with ground-truth data from groundwater quality monitoring of boreholes is required to avoid difficulties in interpretation of data and to better define the extent and migration of pollution in Groundwater.

Jan 1, 1988

By J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte. 5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By W. D. Haselton, J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte.5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

Accounting for borehole damage in analytical modelling of explosively generated stress waves is important for predicting the finer details of the stress wave patterns observed in the field. The classical Sharpe's [19421 concept of an effective borehole larger than the initial borehole diameter has been widely accepted to explain material damage around a borehole. A new analytical model based on dynamic compaction is advanced to predict far-field stress wave patterns. This model supports field data corresponding to reduced frequency of oscillations and increased damping. The present model recovers the earlier result when compaction around the borehole representing borehole damage is ignored.

Jan 1, 1990

By Francisco Sena Leite, Pedro Brito, Gean Frank, PhD Soeiro de Carvalho, Jose, Vinicius Miranda

The consequences of rock blasting with explosives are directly related to the accuracy of drilling and, because they have an effect on fragmentation and ground level, they should be controlled to ensure a problem free production, increase work safety and reduce environment impact. Safety control is one of the most important processes in detonation, since it can compromise the worker security on site and, eventually, neighboring communities. Due to the technology advancements, it is possible to build a hole deviation control device with “of the shelf” parts, and for that reason the authors decided to evaluate the possibility of measuring hole deviation by creating a portable prototype using an electronic sensor capable of measuring the acceleration on objects, that is, to measure the own acceleration of a system, known as "accelerometer" and a micro-controller to handle and treat data. The main idea behind this paper is to validate the power of the Euler method, given the stepping limitations of the sensor and micro controller in order to reproduce of the hole shape. A case study was carried out, comparing the measurements of borehole deviations made by a traditional equipment and the prototype. A mobile application was also created in order to recover and treat and display the data to the user. For validation of the prototype, several holes were measured using the two devices. A residue analysis was used to validate the data obtained. After analyzing and confirming the effectiveness of the new equipment, the normality tests prove a symmetric distribution with null expected residual mean and minimum variance. Consequently, the accuracy of the prototype is evidenced. Thus, the authors aspire to emphasize the potential of using these sensors allied to a traditional numerical method for analysis of hole deviation.

Jan 1, 2019

By Paul Miller, Rene Laprade

Does a 76 mm Ø hole drilled over 45 m deep remain straight? This is the question asked by the Engineering department at Placer Dome's Dome Mine in Timmins, Ontario before they could lay out the initiation sequence in a long-hole production stope. Everyone realized that the holes would wander over such great depths, but it was important to know where they went.

Jan 1, 1998

To develop a simple device for rapidly determining the shearing strength and angle of Internal friction of coal and rock in situ. Approach Use a portable, permissible, hydraulically operated device in boreholes as deep as 100 feet into the rib, floor, or roof of the mine. How it Works The device, called a Borehole Shear Strength Tester (BST), is inserted Into a 3-inch-diameter borehole to the desired depth, locked Into position, and activated to shear the rock or coal in the borehole walls. The normal and shear pressures exerted by the BST, which are recorded during the test, are used to calculate the shearing strength and the angle of internal friction. The BST consists of 3 main components and several minor components. Main components are: ? A shear head with 2 shear plates that bite into the rock when normal pressure is applied. ? A hollow hydraulic jack with RW drill rods that pull the shear head when shear pressure is applied. ? A console with a hand pump and two hydraulic gages to activate the device and to indicate the pressures that apply the normal and shear faces to the shearing plates.

Jan 1, 1981

By David A. Bacca

Hydraulically powered submersible borehole dewatering pumps and emulsion/ANFO blends evolved at about the same time and for the same reasons. Mining operators needed safe, efficient dewatering systems and water resistant products.

Jan 1, 1994

By B. P. Boisen

INTRODUCTION Application Measurement of rock deformation is essential to stability and behavioral monitoring of underground openings. The difficulties of obtaining adequate sample distribution, density, and orientation can frequently be overcome by the use of single and multiple position borehole extensometers. In its simplest form, a borehole extensometer consists of an instrument head, usually anchored in the collar of a borehole, and a number of in-hole anchors, each of which is fixed in place at a known distance from the collar. As rock adjacent to the borehole deforms, the component parallel to the borehole direction causes a distance change between adjacent in-hole anchors, as well as a distance change between individual anchors and the instrument head. These changes are measured by means of a mechanical link (usually wire or rod) extending to the instrument head from each anchor. The resulting data can be used to compute the distribution, magnitude, rate, and acceleration of deformation in the material intersected by the extensometer's borehole. Wire Vs. Rod Extensometers Since the early 1960s myriad varieties of borehole extensometers have become available through the combination of various special features of two basic instruments, the wire and rod versions of borehole extensometers. Recent publications have recommended shallow depth limitations for wire extensometers, and favor rod extensometers for a broad range of borehole inclinations and depths. There are three main reasons for using a deep wire system: its cost effectiveness; the fact that tremendous depth means tremendous rod weight which will cause the rod to buckle or rub against the borehole or casing wall; and users' attitude and proper understanding of how to install and apply a wire-type extensometer. Here experience plays a big role. Over the years, many have learned the hard way that untensioned rod extensometers are simple and inherently inexpensive, but limited to vertical up holes where sensitivity is not influenced by friction between the rod elements and the borehole wall or protective conduit, the inertia of the rod elements, or the direction of the movement to be measured. In deep, horizontal, or inclined holes, and in instances where compressive as well as tensile strains or displacements are anticipated, tensioned rod or wire systems are preferred. System Components Borehole extensometers are made up of at least the following five principal components: the instrument head; the collar anchor assembly; the downhole system of anchors and rods or wires; the signal cable if the head is equipped for electronic readout; and the readout apparatus, whether mechanical or electronic. These components are shown in Fig. 1. Borehole Requirements Most extensometers are designed for installation in nominal 75 to 57-mm (3.0 to 2.25-in.) diam drill holes. Either a diamond drill or a percussion drill hole is satisfactory, provided the variation in drill-hole diameter is within the tolerance of the standard anchor design. The basic system may be modified for other hole diameters by changing the dimensions of the collar anchor and downhole anchor assemblies. Some instrument heads and collar anchor assemblies require enlarged borehole collars, though usually not over 150 mm (6 in.) for a depth of 1 m (3 ft). It is desirable, although not essential, that holes be free-draining. Holes must be clean and free of debris before installation. Depth/Orientation of Extensometer Boreholes Extensometers are designed to measure axial strain components in the instrumented drill hole. As the drill hole is axially deformed, the distances between individual downhole anchors and the instrument head change, as do the distances between adjacent anchors. The distance changes measured by a multiple position borehole extensometer, for example, are reduced to functions of time, hole depth, anchor position, or other parameters of significance in terms of the structure under investigation.

Jan 1, 1982