Search Documents

By Corbett GJ

Magmatic-related low sulphidation hydrothermal ore systems at plate margins exhibit distinct spatial and temporal zonations which can be used to aid mineral exploration and development. Low sulphidation systems at all crustal levels exhibit the same paragenetic sequence of events: early breccia formation, followed by quartz - secondary feldspar - sericite/illite veining, then mineralisation, and final argillic overprint. This sequence of events is interpreted to reflect the initial emplacement of melts at high crustal levels, and the progressive cooling of that melt and release of magmatic constituents into a circulating hydrothermal system.

Jan 1, 1995

By A. W. Asman

An analysis is made of three different types of section production units that represent the manner in which most of the nation's bituminous coal is produced. The general delays and production characteristics of these sections are presented along with a method for evaluating section performance based on actual and theoretical production characteristics.

Jan 9, 1951

By K. G. Thorne, L. J. Cabri, L. R. Fyffe, D. R. Lentz, D. Hoy

"Mineralization at the Main zone of the Clarence Stream gold deposit in southwestern New Brunswick occurs within a parallel series of quartz veins that occupy a NE-trending, steeply north-dipping, brittle-ductile shear zone related to the nearby terrane-bounding Sawyer Brook fault. This deformation zone cuts volcaniclastic sedimentary and volcanic rocks of the Silurian Waweig Formation, and is intruded by mantle-derived East Branch Brook gabbroic dikes and a number of felsic dikes. Intermittent shear-zone reactivation during local magmatic activity induced heterogeneous deformation and alteration of the country rocks and dikes. The terminal phase of shearing is associated with narrow pegmatite-aplite dikes that grade laterally into granophyric granite, and into an auriferous quartz vein. Gold, aurostibite, and gold-antimony intergrowths, predominantly with vein quartz, are associated with a low ƒO2 sulfide mineral assemblage (pyrrhotite, arsenopyrite, and berthierite) that has a sulfur isotopic signature consistent with a magmatic source. Gold saturation and deposition occurred episodically between 300° and 360°C at low activity of sulfur, predominantly in response to pressure reduction during brittle failure combined with the effects of decreasing temperature and sulfidation reactions during fluid-wall-rock interaction. Geochronological studies demonstrate that the timing of the emplacement of the pegmatite-aplite dikes and associated auriferous veins overlap with that of the Early Devonian Magaguadavic granite. Moreover, the composition of the dikes is consistent with their derivation from this granite as late fractionates. The Main zone of the Clarence Stream deposit is therefore interpreted to be intrusion-related, with the Magaguadavic granite being the ultimate source of the gold-bearing fluids. La minéralisation de la zone principale du gisement aurifère de Clarence Stream dans le sud-ouest du Nouveau Brunswick occupe une série de veines de quartz parallèles dans une zone de cisaillement fragile-ductile de direction NE et à pendage abrupt vers le nord apparentée à la faille de Sawyer Brook avoisinante qui délimite deux terranes. Cette zone de déformation recoupe les roches volcaniclastiques et volcaniques de la Formation de Waweig d’âge Silurien et est recoupée par les dykes de gabbro d’East Branch Brook, d’origine mantellique, ainsi que par divers dykes felsiques. La réactivation intermittente de la zone de cisaillement durant l’activité magmatique locale a entraîné la déformation et l’altération hétérogènes des dykes et de l’encaissant. La phase finale du cisaillement est associée à de minces dykes d’aplite-pegmatite qui passent latéralement à des granites granophyriques, puis à des veines de quartz aurifères. L’or, l’aurostibite et les intercroissances d’or et d’antimoine principalement associées aux veines de quartz sont associés à un assemblage minéral de sulfures à faible ƒO2 (pyrrhotite, arsénopyrite et berthierite) présentant une signature isotopique du souffre compatible avec une source magmatique. La saturation en or et la précipitation a eu lieu épisodiquement entre 300° et 350°C dans des conditions de faible activité de souffre, principalement en réponse à la baisse de pression durant la rupture fragile ainsi qu’aux effets de la baisse de température et aux réactions de sulfuration durant l’interaction entre le fluide et l’encaissant. Les études géochronologiques indiquent que l’âge de la mise en place des dykes de pegmatite-aplite et des veines aurifères qui leur sont associées coïncide avec le granite de Magaguadavic, d’âge Dévonien Précoce. De plus, la composition des dykes est compatible avec une origine provenant de ce granite sous la forme de phases fractionnées tardives. Le gisement principale (Main zone) de Clarence Stream est ainsi considéré comme étant associé aux intrusions, le granite de Magaguadavic étant la source ultime des fluides aurifères."

Jan 1, 2008

By M. C. Chapman, P. L. Swanson, A. T. Iannacchione

The National Institute for Occupational Safety and Health (NIOSH) evaluated microseismic activity from three field sites to compare and contrast the characteristics of microseismic emissions from very different geologic, stress, and mining environments. Recently, NIOSH has embarked on a research program to evaluate the use of microseismic monitoring information to identify roof fall failure processes and to assess its potential to warn of unstable roof conditions. Large roof instabilities, such as roof falls and certain roof caving events, have proven difficult to anticipate representing an increased risk to miners working in these inherently hazardous areas. When local failure processes are better understood, appropriate control measures can be engineered to mitigate these hazards. This study used microseismic emissions to help identify three local rock failure processes. It was also shown that analysis of microseismic emissions can aid in assessing the degree of instability associated with these local rock failure processes.

As part of the Australian Mineral Industries Research Association (AMIRA) P9 project, methods of characterising both the ore and the machines in flotation circuits have matured considerably over the past 15 years. Machine characteristics include gas dispersion measurements, such as bubble size, gas hold-up and superficial gas velocity. Ores can be characterised in terms of floatability parameters on a size and mineral basis. Measurements have been performed on various copper plants in many countries around the world over the last 5 years. This paper outlines the cell and ore floatability characteristics of each copper plant and provides a discussion on the differences between these plants. In general, most porphyry copper ore bodies are processed at high tonnage through several parallel banks of cells at each stage of flotation. The floatability parameters of these copper ores are very similar in terms of rate of flotation and proportion of fast, slow and non-floating material. The cell characteristics are also similar, with superficial gas velocity, bubble sizes, and gas hold-up values being of similar magnitude. Investigation of the similarities and differences of the modem copper flotation circuits has allowed an increase in understanding of the particularities of copper flotation. Comparison against other copper circuits provides a benchmark and opportunities for future optimisation.

Jan 1, 2007

By Y. J. Wang

The definitions of system pressure loss (mine head) and system resistance, which are traditionally associated with single-fan net- works, are applied to multiple-fan ventilation networks. The system characteristics -- relations among air power, pressure loss, air quantity and resistance -- are analyzed by introducing the concept of subsystems. These subsystems are associated with the fans located in a cutset of the network. For a multiple-fan network, the resistances for the subsystems and total system are dependent on the quantity ratios of the subsystems. In general the pressure loss of a subsystem or a total system does not vary as the square of the corresponding air quantity. If the quantity ratios of subsystems are all held constant, then the resistances become constant and the pressure losses are predictable from the quantities employing the "square law." The system resistance has a minimum value under the natural- splitting flow pattern. Being independent of the value of system quantity, the minimum system resistance provides a basis for comparing the different networks.

Jan 1, 1983

By J. W. JESSUH

TO certain people the name of Northern Rhodesia brings only a vague recollection of a distant country somewhere in Africa; to others, it means a big game territory and the opportunity for excellent shooting; to some, a land of sunshine and peace; but to mining men the name signifies the land where the latest discoveries of copper ore are astonishing the mining world and bid fair, in a few years, to make Northern Rhodesia one of the largest copper- producing countries. There is a fascination about this part of the globe that is somewhat similar to southern California, and at the same time there is that feeling of mystery peculiar to a tropical climate. Perhaps it is the isolation, the fear of wild animals, or the influence of an undefinable something which cannot be expressed.

Jan 1, 1931

By D. W. Jessup

THE handling of native labor is offering an interesting problem that requires diplomacy. It is difficult to induce many of the men to leave their villages and enter into regular work. They do not feel the necessity of manual labor other than to obtain sufficient money to pay the annual hut tax and to buy a little clothing. The ground provides mealies (corn) which means food and beer, he hunts and catches fish, so why work? But gradually, as the native becomes more civilized, his wants increase and his ideas change; he now needs money to supply his desires and eventually he must work more. So in time it is hoped that the labor market will be better supplied.

Jan 1, 1931

By Seung-Kyu Son, Michael T. Chandler, Youngtak Ko, Gyuha Hwang

Over the past decade, sea-floor hydrothermal vent fields have been studied by many researchers because of their commercial potential of mineral resources and the origins of Earth’s life. Approximately 300 of these are reported as massive sulfide deposits near the mid-ocean ridge, most of which are located in the Atlantic and Pacific ridges. However, only fourteen deposits have been identified in the Indian mid-ocean ridges. The Central Indian Ridge (CIR) between 8°S and 12°S is composed of three segments with a slow full- spreading rate of 33-37 mm/yr. The hydrothermal activity at the slow-spreading center can be generated along the ridge axis attended by volcanism or along the tectonic features, such as oceanic core complexes (OCCs). OCC is an exposed mantle rocks composed of peridotite and ultramafic rocks uplifted through long-lived detachment fault processes which can also lead to extensive hydrothermal circulation near the slow-spreading center. Therefore, the identification of OCC’s properties will be an important indicator for finding the sea-floor hydrothermal vents. To study hydrothermal activity of the CIR, Korea Institute of Ocean Science and Technology (KIOST) have conducted expeditions using R/V Onnuri over four years (2009-2011, 2017). High-resolution bathymetry and backscatter data was obtained during expeditions using multibeam echo system of EM120 in 2009-2011 and deep-tow side-scan sonar system of IMI-30, which has more higher resolution than EM120, in 2017. In this study, we use these high-quality data for constraining location and size of OCC. We also analyze the geophysical and morphotectonic characteristics of OCC gathering high-resolution bathymetric map and backscatter image.

Jan 1, 2018

By David K. Ingram

The objective of this U.S. Bureau of Mines investigation was to characterize overburden response due to longwall mining. Subsurface strata and surface deformations were monitored during the mining of two adjacent, 900 ft wide longwall panels in southeastern Ohio. The panels were separated by a five entry, four pillar system (about 350 ft wide). The overburden thickness in the study area ranged from 214 to 280 ft, and the extraction thickness averaged 70 in. To delineate the geology of the overburden, six coreholes were drilled along a profile line extending across the two longwall panels. Multi-point borehole extensometers (MPBX) with eight-anchors were installed in six boreholes to measure subsurface displacements. The MPBX units were continuously monitored using a data logger. During the mining of the first panel, displacement occurred in a radiating pattern beginning just above the extracted area in the center of the panel and extending upward and outward towards the surface and margins of the panel. Overburden deformation did not project over the gate road entries. During the mining of the second panel, the MPBX's showed almost simultaneous displacement, indicating that the overburden began to move as a whole unit. Again, overburden deformation was confined to the immediate panel area. At both panels, overburden movement began when the longwall face was approximately 55 ft beyond the line of MPBX boreholes. Moreover, all ground movement was complete when the longwall face was approximately 200 ft beyond the line of MPBX boreholes. This paper discusses the results of the study and identifies the characteristics of overburden deformation.

Jan 1, 1986

By Dan E. Lewis, William E. Saegart

Similarities of certain geologic and mineralogic parameters are recognized among the various Philippine porphyry copper deposits. Lowell and Guilbert3 described a model of the typical porphyry copper deposit as the result of comparing numerous Western Hemisphere occurrences. Many of the characteristics of the Philippine porphyry copper deposits differ from the model developed by Lowell and Guilbert. A model of the typical porphyry copper deposit is presented and the characteristics of the Philippine model are compared with those of the Western Hemisphere model. Estimated Philippine copper production in 1975 was 242 446 mt. The total in 1948 was 2091 mt. This represents a 116-fold increase in copper production during the 28-yr period. The Philippines now rank seventh in total world production of copper.

Jan 1, 1978

By William E. Saegart

Copper has been mined in the Philippines since at least as early as the Ming dynasty (1368 A.D. to 1644 A. D.). The principal source areas of this early production were in Camarines Norte (Paracale), in the Mountain Province, which now boasts the largest number of Philippine porphyry copper deposits, in Masbate and in Surigao, The Spanish Era began in 1521. Although they were primarily interested in gold, the Spaniards operated several copper mines including the San Remigio mine on Panay and the Lepanto mine in northern Luzon, beginning in 1842 and 1865 respectively. Prior to World War II most of the Philippine copper production was supplied by these same two mines together with the Hixbar mine, Rapu Rapu Island which began operation in 1939. The Hixbar and San Remigio mines are cupriferous pyrite deposits and the Lepanto is a vein-¬form replacement deposit (Kinkel et al. ,I 1956). No significant copper production was derived from porphyry copper occurrences prior to world War II.

Jan 1, 1976

By Fumihiko Sumiya, Yuji Ogata, Masahiro Seto, Yukio Kato, Yuji Wada, Kunihisa Utsuyama, Yoshikazu Hirosaki

It is well known that emulsion explosives can be dead-pressed especially in underground blasting. Voids in emulsion explosives will affect such malfunction of explosives. To clarify the factors that affect the dead-pressing phenomena, the characteristics of the pressure wave propagation in emulsion explosives were investigated. Three types of microballoons .or microbubbles, glass microballoons(GMB), resin microballoons(RMB) and chemical gas bubbles, were used as sensitizers for emulsion explosives. The pressure profiles inside the explosives were measured to determine the effects of the microballoons or microbubbles contained. The underwater explosion test and the large-scale drop hammer test were carried out to load the explosives with a dynamic pressure and a quasi-dynamic pressure respectively. In the underwater explosion test, the pressure profiles in the emulsion explosives were measured by a piezo-electric pressure gauge inserted to the center of the explosive cartridge which had a diameter of 30mm. In the large-scale drop hammer test, the same type of pressure gauge was placed at the bottom of the explosives. From these experiments, the following results were obtained ; A) The pressure profiles in the sample explosives sensitized by RMB or chemical gases were sharp, while in the sample explosives sensitized by GMB the profile was broad. B) The peak pressure levels in the sample explosives sensitized by RMB or chemical gases were twice as high as that in the sample explosives sensitized by GMB in the underwater explosion test. However in the large-scale drop hammer test, the amplification of the peak pressure is low compared with in the underwater explosion test. C) The impulse value was independent of the types of the microballoons or microbubbles in both tests. It was concluded that the type of the microballoons or microbubbles significantly influenced the characteristics of the pressure wave propagation in emulsion explosives.

Jan 1, 2001

By Minglin W, Zhixing L

The laws of detonation wave velocity variation in propagation process along the charge under channel influence are investigated widely in this paper. The result is obtained by blasting experiments. Bore hole is simulated by plastic tube or steel pipe (with outer diameter 45 nun, inner diameter 40 or 41 mm). Blasting experiment is carried out with a cylindrical charge of 32 mm diameter. The author analyses the characteristics of energy distribution along the charge under above-mentioned conditions. Reasonable initiating position and initiating direction are also analysed. A double-direction initiating method which consists of several initiating charges is put forward. The blasting effect of this initiating method when used in underground mining is stated out.

Jan 1, 1990

By H. L. Lovall

Huge banks of preparation plant refuse and other non¬saleable materials have accumulated over the years in all major United States coal producing areas. These banks, esthetically and commercially undesirable, can cause air and water pollution and land reclamation and mineral conservation problems for the industry and nearby communities Although some refuse banks have been reworked to recover saleable coal, all remain and accumulation continues. Even those previously processed continue as potential hazards. Among the several problems created by refuse banks, in situ combustion is most treacherous. Of the millions of tons of major accumulations, there are at least 450 refuse banks on, fire at this time Attempts to extinguish such fires are costly, impractical and generally unfruitful. Studies are in progress to evaluate the potential of processing such materials to eliminate the combustion capability and to yield usable fuel and nonfuel products. Aspects of the study now in. development for coal refuse include: (a) evaluation of characteristics (size, sink-float, ash, sulfur and calorific value) of the coal refuse materials which are known to be highly variable, (b) development of an ignition test having significance for in situ conditions, (c) study of processing capabilities (comminution for liberation, pilot plant washing tests), and (d) investigation of potentially significant properties of fuel and nonfuel products which could be altered to enhance their market potential.. Among the latter products are lightweight aggregate, fill for mine slushing operations, construction, etc: Plans are to extend the studies to include the design, erection, and test processing of refuse with a transportable plant,; which could provide basic economic and product utilization data from several locations

Jan 1, 1964

By Albert E. Reed

THE development of the modern high-speed vibrating screen, together with the increasing availability of long-lasting stainless-steel screen cloth for relatively fine-mesh separations, means that more screen circuits will be used in the future. It seems pertinent therefore to examine a few characteristics of screen-circuit products, and especially the points of difference as compared with products of classifier circuits. The most noticeable change that takes place when substituting screening for classification in a grinding circuit is a substantial drop in the circulating load, owing to the greater ease with which the "fines" leave the circuit. Where circulating loads of 500 to 600 per cent are considered fairly normal in classifier grinding circuits, the grinding circuit equipped with screens for equivalent work will have a circulating load of only 20 to 75 per cent. As a result, the products of screen circuits will show a minimum of overgrinding or sliming as compared with a classifier circuit. The desirability of this characteristic will naturally vary according to the metallurgical requirement in each case. Because screen separations make a sharper division according to particle size, the products of screen circuits can be expected to show greater crowding of particles near the point of separation. These changes in product characteristics are so important that other factors, both in the grinding and concentration processes must be adjusted if the operator is to take full advantage of the increased tonnages and higher efficiencies available to him through the use of the screen circuit. One factor that too often is overlooked when changing to screen circuits is the importance of adjusting the ball-mill or rod-mill charge, to compensate for: (I) increased tonnage of new feed, (2) decreased circulating load, or (3) more granular character of feed. These same factors should also be taken into consideration for their effect on the various types of concentration or flotation equipment that may follow the screen circuit. Over a period of years, this equipment has generally been designed and adjusted to the product of the classifier, therefore it seems obvious that some research on the adjustment and adaptation of concentrating and flotation equipment to screen-circuit products will be most profitable to the operators. To illustrate the points mentioned above, the results from three recent installations follow, with data on the comparative characteristics of screen and classifier circuits. A range of separation from 10 to 48 mesh has been chosen, using two general types of screening equipment and two types of classifiers. The first of the installations of which the results are to be examined is that of an iron-ore installation where eastern magnetite was being concentrated prior to sintering. Fig. I shows the original grinding circuit, using classification, while Fig. 2 shows the same circuit equipped with a

Jan 1, 1945

By G. Dodbiba, T. Fujita, M. Kawata, S. Yamasaki, K. Mitsuhashi, J. Ponou, Y. Iwazaki, T. Atarashi

"The grade of copper ore and concentrate is recently decreasing and it will continues decrease further in the future. The effective liberation treatment for low grade copper ore and the removal of arsenic from copper concentrate is becoming even more important. In this work, the magnetic separation of copper concentrate by heat treatment and the flotation of low grade copper ore by microwave irradiation was studied. The heat treatment of copper minerals in the air atmosphere, the magnetization of most copper minerals increases and especially the magnetization of chalcopyrite shows the largest magnetization, after being heated at 500 oC. The wet HGMS of copper concentrate has been studied and the results have then been compared with the ones when calcined concentrate was used instead. The microwave treatment before ball milling increased the degree of liberation up to 100%, especially when compared with the case when only ball mill was applied to the as-received ore. The flotation of ground copper ore after microwave irradiation showed that the grade copper minerals such as chalcosite and bornite in froth part is much larger than that of tailing part.INTRODUCTION The copper has been used many kind of technological fields and will be more important for the future technology. The global copper production from mine is predicted as shown in Figure 1 (Northey, S. 2014). The copper production peak will be appeared in 2030 and the demand peaks in 2040. In the future the recycling of stocked copper and copper alloy will be necessary to satisfy the demand (Yoshimura, A. 2018). Changes in the grade of copper in copper concentrate, exported from several countries are shown in Figure 2. The copper grade in copper concentrate after mineral processing is gradually decreases every year and it is less than 30% nowadays. On the other hand, the copper ore grade change and prediction are shown in Figure 3. The grade of copper ore is also decreasing to less than 1% in 2010 (Northey, S. 2014). In the future the copper grade gradually decreases, reaching to less than 0.5% in 2080 and the energy to produce the copper metal will increase. The effective liberation treatment for low grade copper ore and the removal of arsenic from copper minerals become more important, nowadays. The microwave irradiation of copper ore for the liberation, energy etc. has been reported by several researchers (for example, Batchelor, A.R. 2017). The magnetization change of copper ore by heating has been reported to remove the arsenic (Sawada, M 2015). In this report, the magnetic separation of copper concentrate by heat treatment and the flotation of copper concentrate by microwave irradiation are discussed after the characteristics of secondary copper minerals are investigated by these treatments."

Jan 1, 2018

By Donald L. King, Frank A. Baczek

Sedimentation-based equipment is used in applications where separation of solids from liquid by gravity settling is desired. If a concentrated solids slurry is desired, the equipment is designed to "thicken"; if a clear liquid is desired the equipment is designed to "clarify." Thickeners normally handle higher solids loading rates than clarifiers, which usually process feed slurries containing low concentrations of suspended solids. Thickeners are therefore designed for heavier-duty requirements, and clarifiers have extra features to ensure more complete suspended solids removal. Major components (Figure 1) that are common to all sedimentation-based equipment are: tank, drive-support structure, drive unit and lifting device, rake structure, feed well, and a means of overflow and underflow withdrawal. Specific features are designed interdependently after the overall separation approach is defined conceptually. This conceptual approach is usually based on past experience or evolves from sedimentation studies conducted on samples of the slurry to be handled. Because many variations and combinations of components are possible, the overall conceptual approach has a number of possible designs that will accomplish the desired results. The final choice is based on practicality, potential for minimizing upsets, and cost.

Jan 1, 1986

By Jiulong Cheng

Underground coal mining causes overburden deformation and failure, one major form of which is bed separation in the overburden. Surface subsidence can be controlled by injecting grout into the bed separations. For a long time, the grouting results of bed separation can not be validated. This is the problem in the application of this technique. This paper analyzes the conditions leading to bed separation, develops mathematical models for seismic wave fields generated before and after bed separation, and bed separations grouted with different materials, and computes the seismic wave field characteristics using the finite difference method. The results show that the existence of bed separation causes changes in the characteristics of seismic wave field, and that different grouting materials generate different seismic wave field characteristics. Intact strata, bed separation, and bed separation filled with air or water all display distinctive seismic wave field in amplitude and frequency spectra. After mining, the original location that provides strong seismic reflection wave no long exists. It is replaced by a weak and syncline-shaped reflection wave. The area, where the seam wave disappears, is larger than that of the mined area. The location, where a bed separation occurs, generates a set of reflection waves stronger than the normal one. The energy of the reflection waves varies with the materials filling the separations. Bed separations filled with air generate stronger reflection waves than those filled with water. The major frequencies for those filled with air are lower than those filled with water. Therefore, it is possible to determine the property of filling materials by analyzing and comparing the amplitude and frequency spectra of the reflection waves. Case studies of application of seismic method for exploring bed separations and grouting were analyzed. The results show that it is feasible to use seismic technique for exploring bed separations and grouting.

Jan 1, 2006

By Tom Goforth, Rongmao Zhou

The interest of seismologists in mining explosions has increased substantially with the construction of the International Monitoring System (IMS). The IMS supports the Comprehensive Nuclear Test-Ban Treaty by providing global data coverage from seismic, hydro acoustic, infrasonic, and radionuclide sensors that will detect a host of natural and man-made events at regional (<2000 km) distances. Ideally, the recorded data can be used to identify those events that have explosive characteristics and therefore might be clandestine nuclear tests. The regional observations assure the detection of mining explosions, and these must be properly identified to avoid false alarms of the monitoring system. Cooperation with the mining industry, including documentation of the firing programs, provides critical information necessary to characterize the seismograms.

Jan 1, 2006