Search Documents

By Stanley F. French

ELECTRICAL power and distribution for the sulphide ore plant is an addition and extension of the existing power system which has served the oxide reduction plant since its inception in 1914. The power plant is located at Tocopilla on the west coast of Chile, some 90 miles from Chuquicamata. A brief description of this plant and the existing transmission system is necessary to an understanding of the problems involved in the provision for the sulphide plant load. Originally the Tocopilla power plant consisted of four Escher Wyss turbines driving Siemens Schuckert generators, each rated 10,000 kw. At various times, units of 10,000 and 20,000 kw were added, all of which operated at 215 psi and 600°F at throttle. In order to improve the economy of the station, a Topping unit was installed in 1938 together with a high-pressure steam generator of 360,000 lb per hr capacity. This unit is rated at 11,000 kw and was designed for 750 psi, 880°F. The exhaust from this turbine passes to the low pressure station header for operation of part of the low pressure turbines. Total kw generated by the high pressure boiler, topping turbine and associated low pressure turbines totals 33,000 kw and the total station capacity is 113,000 kw. This installation proved one of the most successful of its kind, operating almost continuously. The original plant was of German design and consequently European characteristics were incorporated into the system, the frequency being 50 cycles and voltages of 500, 5000 and 100,000 were used for low, generator, and transmission voltages,

Jan 1, 1952

By J. P. Manning

UNQUESTIONABLY, the outstanding feature of the piping for the sulphide plant is the large amount which had to be done in almost every size from instrument tubing to 84 in. OD pipe. In this article the piping will be considered under the main headings of Yard Piping and Building Piping. Tables I and II give data concerning the individual systems. In the case of yard piping the figures pertaining to lengths and weights are approximately correct; those for building piping are given only for the concentrator and smelter buildings where the amounts were the most extensive. Yard Piping The installation specifications for yard piping called for all sizes larger than 12 in. to have welded joints made with outside welding rings. This type of joint was selected over butt-welded joints because less time would be needed for lining up, damaged pipe ends would be less of a problem, and deflections up to 6° per joint could be made when necessary. These advantages were thought to outweigh the disadvantage of the greater amount of welding required. Yard piping in sizes of 3 to 12 in. was specified to have butt-welded joints made with inside welding rings which were intended to facilitate lining up and keep welding material out of the lines. Screwed connections were specified for sizes under 3 in. No protective coatings or wrappings were required on pipe to be buried because of the dry climate at Chuquicamata.

Jan 1, 1952

By H. G. Dwyer

CONSIDERATION for future expansion influenced the design of the new smelter at Chuquicamata. The section of the smelter now going into operation, while large, represents only little more than half of the ultimate plant. Equipment for the direct smelting of raw concentrates has been arranged in the conventional manner although needless details have been eliminated wherever possible while mechanical and electrical features not usually found in copper smelters have been incorporated. Access is afforded to all equipment but platforms and walkways have been held to a minimum. The poling and other platforms in the converter aisle, normally subjected to battering by ladles and other heavy equipment in transit, are of concrete construction with steel grid armor embedded in the exposed surfaces. Noticeably absent are the many platforms formerly required for the handling of converter flux since this material is charged to the converters through the side walls of the converter uptake hoods. Clear space with ample headroom is provided under each converter and converter puncher's platform to permit clean-up by small bulldozers. Remote controls have been introduced at many points. Electrical control rooms and control centers have been conveniently located. An electrical tunnel with cross tunnels and escapeways is situated under the entire length of the converter aisle for power feed lines. Skull breaking facilities are in a separate building near the smelter. A silica-slurry building with brick storage area is adjacent to the smelter building so that elevator service is available to both buildings. A smelter office, a change house and lunchroom are provided in convenient locations. Units of the smelter as presently constructed are shown in the plan and table on page 1194. The ultimate smelter will house 7 reverberatory furnaces, 14 waste-heat boilers, 9 Peirce Smith converters, 4 casting furnaces serving 2 casting wheels, and one holding furnace serving a straightline casting machine. Additional crane requirements in the converter aisle will necessitate the installation of special hoisting equipment in space already provided in a raised section of the roof over the casting end of the aisle. Thus a complete crane may be lifted high enough above the crane rails to permit the passing of another crane underneath thereby giving all cranes full use of repair facilities already installed. For the collection of gases, 2 dust chambers, each with separate stacks, will collect converter gases and 2 balloon flues with separate stacks will collect reverberatory furnace gases. Extensions necessary to complete the ultimate plant will be possible with little interruption to normal operations since the future converters and reverberatory furnaces will be added at the east end while additional casting facilities will be added at the west end of the present plant. The future units may be added singly or all at one time depending on requirements.

Jan 1, 1952

By Clarence W. Dunham

BECAUSE of the earthquakes that occur at Chuquicamata, the design of the smelter stacks constituted the most difficult structural problem of the entire sulphide ore project. Slight tremors occur almost daily and shocks of moderate magnitude are not uncommon. Naturally, the operation of the smelter depends upon the safety of these stacks, and their resistance to earthquakes was the critical feature of their design. Adequate data of the magnitudes of past shocks at Chuquicamata were not available. However, considering the information that was obtained from experiences in other parts of Chile, a period of one to two seconds was adopted as a basis for the design. To complicate the problem further, the stacks had to provide for operations under a wide variety of conditions ranging from the possibility of running one reverberatory furnace and two converters initially to perhaps five or six furnaces and eight or ten converters simultaneously in the completed plant. No one could tell for certain just what the ultimate capacity might have to be because the plans permitted a large extension beyond the first installation if this became necessary. Studies of the stacks were made for many conditions. At first it was thought that one stack 600 or 650 ft high should be used initially for both the furnaces and converters, with a second similar stack to be built for the future extension. This height would provide adequate draft in the rarified atmosphere at the plant's elevation of 10,000 ft. It would also disperse the gases high in the air. Preliminary studies of this large stack showed that such a structure was possible if made of steel but it would be exceedingly costly. Furthermore, the effects of the tendency for the top to whip under the action of earthquakes might be serious, and the design had to be based upon assumptions which might not be trustworthy. Such a tall stack was finally abandoned in favor of a larger number of smaller ones. Initially, one stack will service the first three or four furnaces. Another will handle the gases from four or five converters. The smelter has been located in such a position that the prevailing winds carry the fumes away from the remainder of the plant. A height of 300 ft for the stacks was finally selected. The top diameter is approximately 24 ft 9 in. clear inside of the lining. The converter stack is located upon a hill alongside the smelter. This provides an effective increase in height because its base is approximately 66 ft above the yard level. The base of the reverberatory stack is at the latter elevation. Stacks made of reinforced concrete or of steel were investigated, and so were many shapes for them. As these studies progressed, the lightness of a steel structure, and the ductility of the metal itself, led to the decision to use steel for the main part of the stacks. The fact that serious damage to one of the stacks would cause the plant to shut down, caused special studies to be made of the stress conditions that might exist around the breeching which had to be nearly 15 ft wide and 40 ft or more high where it joined the stack. This height was necessary in order to provide adequate transition from the horizontal flow of the gases to the vertical direction without undue eddies. This opening constituted a serious source of weakness in the structure. If made with sufficiently strong reinforcement around its edges, there would be a hard spot in the structure that might cause trouble because of shaft vibrations.

Jan 1, 1952

By R. M. Kuralt

CONCESSION from the Chilean government granting the company use of the Rio Salado water stipulates that a minimum of 35,000 metric tons of such salty water must be diverted from the Salado daily, and be disposed of in a manner not to contaminate the Rio Loa to the east of its confluence with the Rio San Salvador at Chacance, Fig. 1. Consequently, the selection of a suitable site for the sulphide plant tailing disposal had the additional problem of the disposal of excess brackish waters. Studies of the terrain in the area directly to the south of the plant indicated that construction of tailing ponds would be costly, and generally unsatisfactory due to excessive slope of the ground, lack of flanking hills, danger of raising the groundwater level thus causing springs along the Antofagasta-Bolivia railroad; and the possibility of creating a dust nuisance at the plant site or at Calama due to blowing sands. Further to the southwest the San Salvador river canyon offered some possibilities and surveys were made at sites A to D, inclusive, Fig. 1. Here again costly dams would have been necessary to impound the tremendous quantity of tailing produced by the new plant, and provision would have to be made to handle a considerable flow of water through the disposal area to the west of the Rio Opache. Additional surveys were made in the area to the southeast of the plant which brought to light the existence of a natural basin of about 14 1/2 square miles, flanked by low-lying hills, and requiring only the most rudimentary dams to close the outlets at the western end. It has been estimated that the Salar de Talabre, as this basin is called, has the ultimate storage capacity of 1 billion tons of tailing with dam heights of only 60 ft. Pipe Line Layout After the decision had been reached to use the Salar de Talabre for the main disposal area various methods were considered for transporting the tailing from the 300 ft diam thickeners to the disposal site, 17.7 miles away. The first plan was to construct a. concrete launder on a 11 pct grade but a survey of this grade line indicated it would not lead directly into the Salar but would terminate somewhat to the north, and from that point on the slope would be considerably less than 1 pct along a natural watercourse. A slope of 2 pct or even 2 ¼ pct in such a rough watercourse or ditch is the ideal, judging from the success of operations at Cananea. Since a simple ditch is the most economical vehicle for the transportation of tailing, it was decided to use one with a 2 ¼ pct grade for as much of the distance as was possible with the existing terrain and to construct a concrete headbox, or forebay, at the terminus of the ditch to supply a steel pipe line leading the rest of the way into the Salar. Referring to the maps of the Chuquicamata area outlining the tailing disposal system, Figs. 1 and 2, one can trace the flow of the tailing from the thickeners to the Salar as follows: The 8-in. spigot pipes from the thickeners (1) discharge into a concrete sump feeding a concrete launder with a 2 pct slope. The launder carries the tailing into a concrete junction box (2) located south of the sulphide plant. The purpose of the junction box is to provide emergency facilities for diverting the tailing flow from the main disposal area to the emergency area. It also provides a junction point for the launder from the sulphide plant's future east extension. The box is fitted with a pair of radial gates controlling flow into the main tailing ditch (6) or the emergency ditch (3) which terminates on the pampa. All ditches are of the same cross section, namely 4 ft wide at the bottom with 1 : 1 side slopes and with a minimum depth of 21/2 ft. Where the nature of the ground demands it, the ditches are lined with stone rubble. The overflow from the plant's 10 million gal reservoir (4) is led into the main tailing ditch by way of a spillway ditch (5). The main ditch terminates in a trashscreen fitted, concrete forebay (7) which serves as a headbox for a 24 in. O.D. x 3/8 in. wall, Dresser coupled, steel pipe (10) and a 12 in. x 8-gage spiral welded, wedge-lock coupled, steel pipe (8). The forebay is fitted with two compartments, one for each pipe, and flow into each is controlled by radial gates. Each compartment is fitted with a 6-in. drain pipe controlled by a rubber pinch valve. To protect the forebay from the abrasive effects of the tailing, the sides of the compartments will be lined with old

Jan 1, 1952

By B. F. Koch

COPPER reverberatories develop large amounts of exit gases of a temperature in the neighborhood of 2000°F. The gases are not only of a noxious nature but must usually be disposed of at considerable heights above the yard level by a stack. Handling these gases at the temperature mentioned would require rather expensive construction of conveying flues and stack. Moreover, wasting such amounts of heat is certainly most uneconomical. Numerous investigations have indicated that waste heat boilers of the water-tube type are the most practical and economical means for utilizing that heat although the gases are heavily laden with rock dust and copper-bearing slag, which upon cooling form hard deposits on the surfaces of dampers or heat absorbing elements placed in the gas stream. Avoiding Slag and Dust Deposits Based largely on the experience of the paper industry in burning black liquor, a waste heat boiler design was developed a few years ago, providing not only extensive water-wall surfaces for cooling the gases below the fusing point of the slag but also settling out, as far as possible, the solidified particles of slag by creating low gas velocity. Matter carried in a stream of gases or air has a tendency to maintain its original direction upon a change in the direction of the flow of the conveying medium. Reverberatory waste heat boilers installed at Hurley and Morenci endeavored to utilize that tendency for the elimination of slagging particles at predetermined places and before they would strike the tube banks of the boilers. Both installations were successful in minimizing the slagging of boiler tubes and thereby minimizing the need for hand lancing. However, the low draft carried at the up-take of the reverberatory furnaces resulted in a positive pressure in the upper part of the furnace of the waste heat boilers, causing the emission of gases from lancing doors and making more difficult the already unwelcome work of cleaning the boilers by handlancing. Attempting to correct this nuisance as much as possible, the overall height of the Chuquicamata waste heat boilers has been reduced to the minimum considered necessary to obtain proper water circulation in furnace walls. Moreover, it is attempted to solidify slag and dust particles by providing large amounts of water-cooled surfaces before the gas stream reaches super-heater and convection banks of the boilers. The furnaces have been made as deep as an economical and practical arrangement of headers for water

Jan 1, 1952

By W. E. Rudolph, R. E. Baylor

DUE to its location in the Atacama Desert, one of the most barren of the earth's surfaces, Chuquicamata's water supply presents unusual problems. Yearly rain-fall averages less than one tenth of an inch at the plant. However, there are summer showers above 12,000 ft in the Cordillera to the east, the resulting run-off flowing through old river valleys buried beneath more recent volcanic formations, to be impounded within sediment-filled basins. This water emerges at springs where the outlets of these basins are blocked by lava flows, and here are formed the small streams which feed the only important river of the region, the Rio Loa. Chuquicamata's water is obtained from these springs and rivulets. [ ] The map above indicates four pipe lines from which potable and industrial water are supplied. Potable water, amounting to 4500 metric tons per day, is conveyed in the Toconce pipe line from springs 59 miles due east of Chuquicamata. This water is used not only for drinking, but also for boilers and other needs requiring high quality. For industrial water at the oxide plant, there are two 12-in. pipe lines from the Rio San Pedro, carrying a total of 17,000 metric tons per day of slightly brackish water. This water is at present used mainly for leaching and for hygienic purposes. Water Source Found For the present and future needs of the sulphide plant, it was calculated that at least 32,000 metric tons per day of make-up water would be required. For this purpose, a pipe line of 44 miles length was constructed to bring in the entire flow of the Arroyo Salado, one of the eastern tributaries of the Loa. The salt content of this water is so high (over 5000 parts per million of solubles, mostly chlorides) that it is highly detrimental to farming, and the Chilean Government had been studying projects to separate these waters from others of the Loa system in order to improve agricultural conditions in the fertile valley of Calama. So it happened that the Government was willing to award rights to the Arroyo Salado waters under agreement whereby the Mining Company removes waters from the Rio Loa system above Calama for all time. The outlet of these waters, after serving their purpose at the new concentrator and leaving the plant in tailing, is the Salar de Talabre, an old salt lake which presents fully ten square miles of surface to serve as an evaporating pan, the outlets having now been blocked by dams. Here the dry climate of Chuquicamata is a favourable factor, evaporation averaging slightly above 1/4 in. per day. The Toconce and San Pedro pipe lines have been functioning from 26 to 34 years, and through the use of special cleaning tools which were developed at the plant, as well as deaeration of the more active Toconce water, these pipes are now maintained at capacities which do not diminish as years go on. Constructing the Dam The Arroyo Salado pipe line design and construction involved certain special and interesting features, and inasmuch as this line and its intake works are solely for the needs of the new sulphide plant, more detailed description is given. The waters are impounded at a gravity dam constructed of concrete to a height of 100 ft above the river bed, keyed into the precipitous Dacite walls of the narrow canyon (barely 6-ft wide at the bottom, only 25-ft width at 50 ft above). A small secondary dam was built 100 ft down stream from the main dam, providing a pool of 15-ft depth to protect the main structure from flood flows over the spill-way during the rainy season. A system of four 36-in. syphons was designed for discharging these flood waters from the lower depths of the lake, in order to avoid eventual sedimentation behind the dam. The lake has a length of 3300 ft, and its water level is controlled by an adjustable spillway permitting draw-down of eighty inches, amounting to 41,000 metric tons of available capacity. This regulation is necessary because of wide fluctuations in stream flow between day and night due to freezing of feeders. During the construction of the dam the entire river flow was handled within a 36-in. pipe line some 2000 ft in length. As the excavations proceeded

Jan 1, 1952

By J. C. Salas, A. Weishaupt, J. A. Guzman

The origins of the electrorefining process date back to 1869, when the first ER cathodes were produced at Pembrey, South Wales. By the time that Pembrey was closing, Chuquicamata tank house was under construction, initiating in 1915 a long history of electrolytic cathodes production. Initially electrowon cathodes and later electrorefined cathodes were produced. During the history of Chuquicamata tank house, there have been several challenges associated with the quality demanded for electrolytic copper. Among them, the transformation from electrowinning to electrorefining in 1952, the onset of the direct commercialization of ER cathodes and the phase out of wire bars in the 80s, several technological changes including the implementation of permanent cathodes, and certainly the constant increase in complexity of the anodes refined. This paper explores the manner in which Chuquicamata has addressed these challenges and examines its links to process characteristics, which have been necessary to maintain a product quality according to market requirements and a brand, “CCC”, that is widely recognized worldwide. INTRODUCTION Located in the north of Chile, in the Atacama Desert, Chuquicamata is an open pit copper mine that for many years has played a relevant role in the global and local mining industry. Known from prehispanic times, the Chuquicamata deposit was initially developed between 1912 and 1915 by the Chile Exploration Company, the operating company of the Chile Copper Company controlled by the Guggenheim Brothers in the USA (Yeatman, 1916). Officially inaugurated on May 18th, 1915, by the President of Chile who pressed a button in Santiago sending a telegraph signal to the power generation plant specially built in Tocopilla, 1500 km north. It signaled the beginning of generating energy, sending it to Chuquicamata, another 140 km east (“El mineral de Chuquicamata”, 1915), marking the beginning of its industrial operation.

Jan 1, 2019

By Arthur Notman

(San Francisco Meeting, September, 1915) SACRAMENTO HILL is a mass of granite porphyry intruded along a fault between Paleozoic sediments and pre-Cambrian schists in the Bisbee district, Cochise County, Arizona. The intrusion invaded both walls of the fault to a large extent, and the accompanying extensive mineralization of the Paleozoic limestones is the locus of the great high-grade copper orebodies of the Bisbee mines. Prior to 1909, although the presence of ore in the mass of the hill itself had long been suspected, systematic exploration had not been attempted. A few shallow pits on the surface here and there had disclosed some chalcocite with associated carbonates as stringers in a mass of strongly brecciated, silicified, and iron-stained porphyry. The workings in the surrounding limestones had penetrated the porphyry in a dozen or so places for some distance from the contact but had disclosed no ore. However, the rock had been largely altered to quartz and sericite and very thoroughly impregnated with pyrite and traces of the copper sulphides. A close geological study of the conditions, both surface and underground, strengthened these suspicions, and plans for prospecting the hill were made in 1909. Reference to the accompanying illustrations, Figs. 1 and 2, will give an idea of the general appearance of the surface. The mineralization is more intense in two main zones, one at the west end and the other at the east end of the hill. The outcrop of the hill is elliptical and approximately 3,000 ft. long by 1,400 ft. wide. The Sacramento shaft, which is the main hoisting shaft of the mine and situated at the east end of the hill, as shown by the accompanying map (Fig. 3), offered a convenient base for prospecting that end of the hill, while the workings from the Holbrook shaft offered a similar opportunity at the west end. The choice of level for the first work was determined by analogy with the most favorable depth for enrichment below surface observed in the other disseminated deposits of the Southwest.

Jan 8, 1915

[ ]

Jan 1, 1938

[ ]

Jan 1, 1938

By Jaime Díaz Yosa

El presente texto describe el proceso de cianuración en la planta de Orcopampa (Arequipa) a través del vat leaching o método de lixiviación en tinas impermeabilizadas. El método consiste en que después de llenado el mineral, se riega con el lixiviante (solución química) durante un período de tiempo y se percola a través del mineral y disuelva los valores presentes. Luego, esta disolución es recolectada en la base de la tina a través de un drenaje francésy se traslada a otro proceso para la recuperación de los valores disueltos. En consecuencia, la cianuración en vats leaching de concentrados gravimétricos y concentrados de flotación con alta ley de oro se presenta como la alternativa idónea para aquellas operaciones donde las características de los concentrados contienen las condiciones apropiadas para una lixiviación rápida, con altas recuperaciones y bajos costos.

Jul 31, 2003

By Luis de la Cruz Rengifo

El presente trabajo señala el tratamiento del concentrado gravimétrico con alta ley de oro en la planta concentradora Compañía de minas Orcopampa S.A. La aplicación del tratamiento se realiza a través del proceso de cianuración convencional y la implementación de la electrodisposición de las soluciones ricas. Como resultado del proceso, se obtienen barras de oro y plata metálicas puras y el concentrado cianurado sin presencia de oro grueso, eliminando el problema de ensayo y muestreo respectivos.

Apr 1, 1991

By H. Ahrens

El presente estudio refiere la importancia de los explosivos y detonaciones en el campo de la minería a través de una breve revisión historiográfica, legislación, problemas relacionados con la voladura y métodos empleados. Cabe sa señalar que la evaluación de estos explosivos, así como las pruebas características de estos conllevan una aplicación práctica, de forma que se pueda conocer la composición del explosivo y determinar una posible falla en los disparos.

Nov 20, 1972

By Félix Lewandowsky

El presente texto describe las actividades para corregir los pasivos ambientales heredados y asumidos bajo responsabilidad de la Compañía Minera Colquirrumi S.A. Para ello, se elaboró un plan de cierre de los cuatro depósitos de los relaves de Hualgayoc donde se busca mostrar los criterios utilizados, los estudios de ingeniería y la forma cómo se ejecutaron las obras de cierre definitivas de los depósitos de relaves.

Jan 1, 2015

By Ezequiel Pomachagua Quijada

En el Perú, el cierre de yacimientos es una etapa nueva de la vida productiva minera, pues a partir del año 2005 la norma rige y se les otorga un plazo de un año para elaborar y lograr la aprobación del plan de cierre de todas las unidades mineras. Sin embargo, en el año 2008-2009 se iniciaron las actividades de rehabilitación en unidades mineras que no habían logrado su aprobación. En ese sentido, el presente artículo señala la experiencia sostenida por la empresa C.M Centauro como ejemplo de cierre progresivo en botaderos de desmonte. La restauración se inició con el botadero suroeste a través de tres etapas: cierre progresivo, cierre final y postcierre. Así también planificó el cierre de los componentes desde el diseño mediante actividades como la estabilidad física, remoción, perfilado y conformación de banquetas, estabillidad química, extendido de caliza, batido de caliza, compactado de sustrato estabilidad hidrológica, biológica y revegetación.

Aug 1, 2015

By Carol Harrison

"Diseñar, implementar y evaluar un proceso de adquisición de tierras y reasentamiento ha sido un reto para los proyectos mineros en el pais, pues es un tema fundamental para el desarrollo del proyecto y reviste al mismo tiempo una alta complejidad en contextos sociales como el nuestro. Asimismo, no existe una reglamentación clara al respecto ni una institucionalidad que permita enmarcar el proceso, que al final resulta en una negociación directa entre dos partes. La presentación profundiza en ejemplos de experiencias de reasentamiento rural, particularmente en la definición y monitoreo de indicadores."

Sep 1, 2017

By Steven Dempsey

Overview What is Tubbing? A look at Cigar Lake Tubbing Design The Tubbing Installation Backwall Grouting

May 1, 2013

By Martin Wacker

Cameco Corporation, on behalf of a joint venture, is preparing surface and underground facilities at their northern Saskatchewan property in preparation for the future operation of a high-grade uranium mine. The Cigar Lake orebody is situated about 430 metres below surface at the unconformity between metamorphic basement rocks and flat lying sandstone. Major technical factors influencing the mining method selection include ground stability, control of ground water, radiation exposure and ore handling and storage. A decade-long test mine program resulted in the selection and validation of ?jet boring? a non-entry mining method. Cigar Lake?s jet boring mining method involves several major steps; artificial ground freezing of the orebody and surrounding rock, TBM (tunnel boring) type development of access crosscuts below the orebody, installation of cased pilot holes upwards through the ore, and ore extraction using a rotating high pressure water jet within the pilot holes. The resulting cavities are surveyed and backfilled with concrete. The ore slurry will be processed underground and pumped to surface. This paper discusses the jet boring mining method in general terms and includes highlights of the Cigar Lake test mine program completed in 2000.

Apr 1, 2005

By G. Van Weert

In the spring of 2010 double refractory ores from historical stockpiles were processed through Barrick's Goldstrike pressure oxidation facility, thereby providing preg robbing feeds for a variety of metallurgical testwork. This paper describes the effects of amount, type, place and time of addition of activated carbons on CIL gold recovery and shows that native carbon in plant PDX'ed discharge solids can still preg rob gold loaded activated carbon.

Jan 1, 2011