Search Documents

By Lauro Lacerda

Shotcrete is a highly adaptable and widely used underground construction material at infrastructure and mining projects around the world. In fact, many projects could not have been completed without its utilization. As underground projects became larger the use of mechanized wet-mix spraying gradually replaced manual dry-mix shotcrete applications. This paper details some of the reasons for that and provides information on the equipment and operational factors including safety and productivity required to successfully complete underground shotcrete projects.

Jun 13, 2021

By Roland Arnold, Richard Gradnik, Martin Zeindl

This paper presents the details of the Kramer tunnel project in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of GarmischPartenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million (incl. VAT), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for single-tube tunnels is solved by a parallel escape tunnel passable for vehicles. All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). In order to reduce the geological risk for the owner, the escape tunnel was supposed to be completed before the design process for the main tunnel ever began. The exploratory tunnel was awarded to a competitor with an separate contract.

Jun 13, 2021

By Mohamed Younis, Keith Ward

INTRO PAGE

Jun 13, 2021

By Jesse Salai, Colin Sessions

INTRO PAGE

Jun 13, 2021

By Will Hodder, Martin Mancini

INTRO PAGE

Jun 13, 2021

By Stephen Njoloma, Amitabha Mukherjee

INTRO PAGE

Jun 13, 2021

By Aaron McClellan, Eric Levonas

INTRO PAGE

Jun 13, 2021

By Andrew Bursey, Colin Lyons

INTRO PAGE

Jun 13, 2021

By Dave Dorfman, Ben DiFiore

INTRO PAGE

Jun 13, 2021

By David Watson, Steve Price

INTRO PAGE

Jun 13, 2021

By Oliver W. Marsden, John O. Marsden

This paper presents the results of a hypothetical case study that evaluates the potential transition of a large copper mining and extraction operation to 90% renewable energy. The case study considers three phases to accomplish such a transition; phase I considers installation of renewable power generation at the site to meet a portion of the current electric power needs, phase II considers conversion of diesel combustion mining equipment to electric equipment, and phase III considers implementation of renewable energy generation coupled with energy storage systems to provide approximately 90% of the total mine site energy requirements. The paper evaluates the results in the context of a range of purchased electric power unit costs ($0.065, $0.100, and $0.135/kWh) as well as various carbon tax scenarios ($0, $5.00, and $37.30/t CO2). While the case study is hypothetical and considers a range of assumptions, it clearly identifies a pathway to potentially economically viable transitions to a renewable energy platform for mining companies. This represents an approach that mining companies can use to help to meet emissions targets, as well as social responsibility and reporting requirements.

Jun 4, 2021

By F. Sundqvist, B. Skawina, J. Greberg, A. Salama, M. Astrand, P. Ekbeck

Today’s mining operations require fast reporting and rapid rescheduling based on updated information. An automatic mine scheduling system could not only quickly reschedule but also propose alternative solutions. To avoid the financial and physical risks associated with testing such a system directly in operation, it could be first evaluated via discrete event simulation models. This would offer a safe environment to evaluate different operating rules and algorithms. In this study, this is achieved by integrating automatic scheduling software with a discrete event simulation model.

Jun 1, 2021

By J. A. Kinnaird, B. J. Youlton, K. L. Youlton

Methods for treating and processing refractory gold ores are well established. However, what is less well understood is how the formation of the gold-bearing deposits affects gold processing and extraction. In order to evaluate the effect of ore genesis on gold extraction a number of South African gold deposits were studied. These included complex Pilgrim’s Rest samples as well as refractory Fairview, Barbrook, and Consolidated Murchison samples. We found the refractory nature of gold ores is controlled by a limited number of well-understood mineralogical factors. Solid solution gold is linked to low temperature and pressure conditions in fine-grained sedimentary lithologies, while reactive pyrrhotite can form from hydrothermal fluids associated with mafic magmatic rocks. These formational controls can be used to identify and avoid complex deposits at a desktop study phase, or address and reduce complications further along the pipeline using early mineralogical studies.

Jun 1, 2021

By Y. Rao, Y. Huang, G. Wang, W. Liu

The properties and deterioration in strength of cemented tailings backfill (CTB )in the underground acidic environment under oxidizing conditions were studied. X-ray diffraction analysis and scanning electron microscopy of the surface of the CTB was carried out, and the sulphuric acid corrosion mechanism elucidated. The properties tested included compressive strength, elastic modulus, cohesion, internal friction angle, variation in the hydrogen ion concentration, and stress-strain relationship in different corrosion periods. The damage model of the CTB was established considering the effects of parameters such as corrosion time and strain on the damage evolution. It was found that the compressive strength, elastic modulus, cohesion (binder effect), and internal friction angle increased at first and then decreased with exposure time. In the long term, the peak stress decreased with corrosion time while the peak strain increased; elastic modulus, and deformation modulus also decreased. The damage caused by corrosion and by load were related by means of a mathematical model, which revealed the relationships between sulphuric attack, load, and damage to backfill in complex underground environments. During corrosion, the expansion of gypsum and ettringite caused microfractures in the CTB. With increasing corrosion time, micro-cracks developed and proliferated. The mechanism of corrosion damage was found to be the dissolution of hydrogen ions and a sulphate ion reaction that produces an expansive substance, resulting in deterioration of the strength of CTB.

Jun 1, 2021

By J. W. van der Merwe, K. G. Moloko

Furnace wall tubes from 600 MW subcritical boilers at three coal-fired power stations were sampled and the fireside deposits examined to determine the mechanism of fireside corrosion. This involved an indepth investigation into the morphology and composition of the fireside deposits and the conditions of the furnace that enable this type of attack. SEM-EDS analysis revealed high concentrations of oxygen, iron, and sulphur, QEMSCAN and XRD analyses identified the presence of Fe3O4, Fe2O3, FeS, and FeS2. Differential thermal analysis showed thermal activities at temperatures of 500–600°C, 900–1100°C, and 1100–1250°C, which are associated, respectively, with FeS2 oxidation to FeS and Fe2O3, at 475–525°C, formation of aluminosilicates at 925–1100°C, and melting of FeS around 1190°C. The absence of sodium and potassium eliminates the contribution of molten alkali sulphates to the corrosion. The consistent coexistence of iron sulphide and iron oxide is indicative of the substoichiometric conditions in the furnace, while the detection of pyrite suggests that the coal is not completely combusted, which points to a poor combustion process. These observations were affirmed by gas analysis at one of the stations, where very high levels of carbon monoxide were measured at the furnace wall (≥ 14 000 ppm) and furnace exit (≥ 3500 ppm). The high CO concentrations are indicative of limited combustion caused by limited O2. These reducing conditions promote the formation of FeS-rich deposit, which is the corrosive species responsible for degradation.

Jun 1, 2021

By L. Uotinen, M. Rinne, R. Mishra

Underground mining gives rise to geotechnical hazards. A formal geotechnical risk assessment can help to forecast and mitigate these hazards. Frequentist probability methods can be used when the hazard does not have many variables and a lot of data is available. However, often there is not enough data for probability distributions, such as in the case of new projects. The risk assessment is often subjective and qualitative, based on expert judgement. The purpose of this research is to present the use of Bayesian networks (BNs) as an alternative to existing risk assessment methods in underground mines by combining expert knowledge with data as it becomes available. Roof fall frequency forecasting using parameter learning is demonstrated with 1141 sets of roof fall data across 12 coal mines in the USA. The prediction is nearly identical for individual mines, but when multiple mines are evaluated it is difficult to find a single best fit distribution for annual roof fall frequency. The BN approach with TNormal distribution was twice as likely to fit the observed data compared to the Poisson distribution assumed in the past. A hybrid approach using BN combining multiple probability distribution curves from historical data to predict annual roof fall is proposed. The BN models can account for variability for multiple parameters without increasing the complexity of the calculation. BNs can work with varying amounts of data, which makes them a good tool for real-time risk assessment in mines.

Jun 1, 2021

By E. van Steen, G. M. Leteba

Optimizing the catalytic performance of multimetallic nanoparticle (NP) catalysts demands a concrete understanding of their design, while preferentially deploying wet chemical synthesis procedures to precisely control surface structural properties. Here we report the influence of reductants such as hydrogen-rich tetrabutylammonium borohydride (TBAB) and carbon monoxide-rich molybdenum carbonyl (Mo(CO)6) on the shape and morphological evolution of Pt-based binary (PtNi and PtCo) and ternary (PtNiAu and PtCoAu) nanostructures derived from a homogeneous solution of aminebased surface active agents (surfactants) in a high boiling point solvent. We successfully synthesized nanostructures exhibiting well-defined and composition-controlled surfaces deploying a one-pot synthetic approach. The development of the surface properties was, however, observed to be alloyspecific. The resultant highly monodisperse alloy NP with narrow size distributions and facet-oriented surfaces are expected to display enhanced functionality as catalysts for utilization in specific chemical reactions.

Jun 1, 2021

By Q. Liu, S. Liu, Y. Cui

To reduce the frequency of mining incidents and improve safety and production efficiency, it is important to develop technology for the autonomous positioning and navigation of mining equipment, without the assistance of satellite navigation signals. In this study we review the current technological environment for positioning and navigation underground and present several integrated navigation strategies. Existing underground positioning and navigation technology is described, and the performances of different methods based on this technology analysed and compared. The combination types and positioning effects of underground positioning and navigation strategies are discussed. Recent research directions for filtering methods and positioning estimation algorithms for underground positioning and navigation are reviewed. Finally, we summarize the future direction of underground positioning and navigation technology and related algorithms.

Jun 1, 2021

By A. K. Raina

Blast induced damage to the final wall of rockmass in any civil or engineering application is a major concern to the rock excavation engineers. There are at least four distinct techniques practised by blasting engineers to minimise the damage to the parent rock during blasting that are classified as contour blasting. One of the methods to achieve a smooth wall or rock surface in blasting is pre-splitting, where blastholes in the final row are mildly loaded with explosives and fired first in sequence before the rest of the holes in a round of blast to achieve a split in rockmass. Since blasting is one of the most adopted methods for achieving a final wall in a desired shape, while maintaining the rockmass integrity, the design of pre-split blast assumes importance. There are several variables that determine the final shape of the pre-split face including the rock type, the drill diameter, the explosive characteristics, the orientation of major joints with respect to drill hole, the linear charge density, the spacing of drill holes and inclination of the drill holes. This study attempts to determine the importance and sensitivity of variables in pre-split blasting using historical data from open excavations of a hydroelectric project in India. Keeping in view the multitude of variables, low correlation of independent variables with responses and high level of interactions between the variables that define the blast results, it was found suitable to use ANN to determine the importance and sensitivity of the variables involved. A new method to determine the blast induced damage to rockmass, namely, undamaged area (AUD%), is introduced. Half Cast Factor (HCF%) and AUD%were calculated for a high wall and trenches by digital image analysis technique using the Fragalyst software. Joint spacing and linear charge density emerged as most controlling variables in determining the final result of pre-blast. The relative importance of other variables assuming significance in the case of both the designed outputs is also discussed. A comparative analysis of HCF%and AUD%on the basis of results obtained from ANN analysis is also presented. A futuristic approach concept has also been introduced.

May 30, 2021

By CHENCHEN SUN, GUOPING LUO, GUOCHENG ZHANG

Preparation of briquettes by adding CaF2 reagent into the Australian iron ore powder. The structure and morphology of iron ore briquettes during various reduction stages (i.e., Fe2O3→Fe3O4, Fe3O4→FeO, and FeO→Fe) were observed via an ore microscope and scanning electron microscopy. The results showed that CaF2 reacted with SiO2 to form CaO and SiF4 gas during the roasting process. The reduction swelling index decreased from 12.36 to 8.83% when the CaF2 content in the briquettes increased due to CaF2-mediated refinement of the hematite grains during the first stage of the reduction process. Lattice distortion resulting from the presence of Ca2+ in the FeO lattice during the second stage of the reduction process, coupled with an increase in the porosity of the iron ore briquettes and the formation of a low-melting-point slag phase, promoted the anisotropic growth of FeO lamellar crystals, which resulted in an increase in the reduction swelling index from 4.27 to 7.36%. During the third stage of the reduction process, the growth of iron whiskers was promoted by wüstite (FeO) lattice distortion caused by a solid solution of Ca2+ in the FeO lattice; the reduction swelling index increased from 15.61 to 24.72%, resulting in the catastrophic swelling of the iron ore briquettes.

May 27, 2021