Search Documents

By Ted Nuorivaara

The use of polymer-surfactant mixtures as foam stabilization agents is a topic that has drawn the attention of several fields but has so far not be thoroughly studied in the context of mineral froth flotation. The present work showcases a study on the impact on flotation performance of cellulose surfactant derivatives and their mixtures with commercial frothers. Bubble size and foam property measurements were run in a two-phase system along with laboratory-scale flotation experiments conducted using a porphyry copper ore from a mine in Finland. A comparative analysis on recovery, grade and flotation kinetics is presented on the products obtained using: i) a partially hydroxylated cellulose derivative (i.e. hydroxypropyl methyl cellulose; HPMC), ii) a commercial polyglycol-ester frother (Nasfroth240; NF240), and iii) mixtures of these two. The results show that using frothers with a total concentration of 30 ppm, the HPMC-NF240 mixtures provide advantages in terms of Cu recovery, (i.e., up to 95%), compared to the use of either NF240 (ca. 76%) or HPMC alone (ca. 1%). Interestingly, only a small proportion of HPMC mixed with NF240 was sufficient to produce a measurable increase in recovery. This improved performance was attributed to a synergistic effect of the polymer-surfactant mixture which further reduced the bubble sizes in a two-phase system compared to that of NF240. The present work offers a further step into understanding the phenomena taking place when a short chained surfactant is either substituted or mixed with a cellulose derivative, offering potential ways of exploiting this behavior for the enrichment of minerals. INTRODUCTION Froth flotation has been the predominant technology used to beneficiate sulfidic copper minerals such as chalcopyrite ever since it was invented in the late 19th century. The reason for the domination of flotation technology lies behind its versatility in selective separation as well as relatively cheap operational costs (Wills & Finch 2015). Even though flotation of sulfidic copper minerals is moderately well understood based on the broad research work done around the subject (e.g., Albijanic et al., 2015, Bournival et al., 2017, Wang et al., 2015, Mikhlin et al., 2015, to cite only a few), the modern era presents new challenges to the primary raw material industry, including questions regarding sustainability of mining operations accompanied by a need to improve the process efficiencies due to declining ore grades (Edraki et al., 2014).

Jan 1, 2019

By B. Adams, T. Angelov, G. Sasov, D. Steinhilber, A. L. Tsekov, S. Neufeind

A complementary ion exchange/solvent extraction process for the recovery of copper from low- grade ores is described. It has successfully been implemented on a full-scale plant level at the Buchim Copper Mine in Macedonia, yielding a maximum copper cathode production of 2400 tons per year. Compared with conventional SX/EW operations, this technology makes the exploitation of low-grade copper ores economically attractive, due to reduced operational and capital expenditures. Furthermore, the additional Lewatit® ion-exchange installations diminish the volumes of harmful organic substances in the following SX step and minimise the risks associated with the handling and usage of these chemicals, such as environmental pollution or fires. Finally, the significantly diminished quantities of liquids for the SX operation have a tremendous effect on the footprint of the plant (ca. 50% less) thereby leading to a reduction of capital expenditures. This paper reviews the main stages of the combined IX/SX process, the applications for metal recovery and introduces projects where the process is applied. Key findings of the process are also presented. A comprehensive technical comparison between processes has been carried out. This paper also evaluates the advantages of using combined IX/SX technology as a purification and separation step in copper production process, with the aim of further increasing the overall copper recovery and to ensure that a suitable copper concentration in the advanced electrolyte is achieved. The implementation of a Ion Exchange (IX) process in the classic Solvent Extraction-Electrowinning process(SX/EW) is found to be beneficial for processing of pregnant leach solutions both from spent and new copper heaps and dumps, acid mine drainage and other industrial streams without any preconditioning as well as in terms of achieving improved recoveries and copper cathode quality. INTRODUCTION The concentration and separation of copper from primary leachates is one of the key operations in the hydrometallurgical processing of oxide ores (Langner, 2011). Conventionally, this basic operation is conducted by submitting the pregnant leach solution (PLS), with a 1–5 g/L Cu content, from the initial sulfuric acid leach to a solvent-extraction (SX) process in which copper reports to the organic phase. After phase separation, the metal is stripped from the extractant/diluent mixture employing sulfuric acid to furnish a concentrated metal solution, usually containing 40–50 g Cu/L. The final products of the overall process are copper cathodes, which are obtained from a terminal electrowinning step.

Jan 1, 2019

By H. M. Lizama, R. L. Stephens

Secondary leaching of previously leached supergene copper ore has been developed and implemented at Teck’s Quebrada Blanca operations. This consists of using in-situ leaching techniques aided by geophysics to recover the residual metal value from dormant copper leaching heaps. These heaps of crushed and agglomerated ore had been leached 20 years previously but still contained significant copper values. The concept was first tested on a 3,200 m² sector, where injection wells introduced leaching solution into a production zone and electro-resistivity tomography was used to track solution movement within. Operating parameters such as well spacing and injection flow rates were determined. Copper recovery and leaching performance were evaluated based on solution and metallurgical balances. Both ferric leaching and bacterial leaching were enhanced through strategies to pull air into the heap. Positive results from the initial test prompted a larger, industrial pilot test on a 60,000 m² area and 97 injection wells. This larger test obtained a copper recovery of 30% in 457 days. Secondary recovery is now being implemented to all of the abandoned heaps at Quebrada Blanca and has become a production stream. This technology has the potential of wide application to mature copper heap leach operations, and Teck has patented the process and associated methodologies. INTRODUCTION Heap leaching of copper secondary sulphides has been carried out at Quebrada Blanca (QB) since 1994. Ore from the supergene deposit was crushed and agglomerated prior to leaching. Originally, the ore was leached in 6 m lifts stacked one on top of another, known as a static pad configuration. However, in 1998, after the second lift, the operation changed to a dynamic pad configuration; the ore was leached in a single lift and the resulting residues were removed to make way for fresh ore (Yáñez, Ahlborn, & Ramos, 2007). The first two static lifts were left in place and served as a foundation for the dynamic lifts above. Those two buried lifts of leached residues, some 16.8 million tonnes and covering an area of approximately 0.71 million m², remained buried under the dynamic pad.

Jan 1, 2019

By A. Navarra, Norman Toro, T. Marín, Fernando Ayala

The quantitative techniques to evaluate the enhancement of a particular unit operation should consider the corresponding changes to the adjacent unit operations. For example, the expansion of off gas handling capacity should consider the corresponding changes in converter cycle times, matte grade, and other operational parameters, that can provide the optimal system-wide benefit. In general, the upgrading of smelter equipment is risky due to the size of capital investment, as well as any unforeseen impacts on rest of the operations. However, this risk can be mitigated by applying the principles of Front End Loading (FEL) in the formulation of multiphase re-engineering projects. The initial phases of engineering are relatively inexpensive, and determine whether or not to pursue the subsequent phases that are comparatively more expensive. Each phase of engineering depends on increasingly detailed descriptions regarding the critical phenomena that can effect design decisions; the increasing levels of detail may result from numerical simulations, as well as laboratory and plant trials. The quantitative framework should be sufficiently flexible to accommodate these increasing levels of detail, regardless of the particular phenomena, so that it may evolve throughout the project. The current article describes the combined usage of mass balancing, thermochemistry and multiphysics, in the development of discrete event simulation (DES) and finite differences (FD). The incorporation of finite differences into a DES framework depends on adaptive time-stepping, to determine threshold-crossing times, e.g. when the matte temperature surpasses a critical level that necessitates the addition of cold charge. The hybridization of DES and FD is appropriate for multiphase smelter development projects, as it supports semi-continuous material flows, operational policies and scheduling, as well as unexpected events and trends, in increasing levels of detail. This type of framework will support the installation and tuning of modern control systems, including state-of-the art sensors and machine learning algorithms.

Jan 1, 2019

By N. Moelans, I. Bellemans, K. Verbeken

In this work, we present a phase field model to simulate the facetted crystallization of Fe3O4 in a quaternary FeO-Fe2O3-Cu2O-SiO2 melt under different partial pressures of oxygen. An important focus in creating more realistic phase field models is the incorporation of the thermodynamic driving forces in multicomponent multiphase-field models by coupling to thermodynamic databases. The diffusion of FeO, Fe2O3 and Cu2O is considered. The ratio of FeO/Fe2O3 at the upper boundary is in equilibrium with the oxygen fugacity of the atmosphere, while conserving Fe. Two-dimensional simulations are performed with different varying oxygen fugacity in the atmosphere. For the considered composition range, the growth velocities of the spinel crystals increase with decreasing oxygen fugacity. INTRODUCTION Crystallization of silicate melts has its applications in geology, pyrometallurgy and glass making. In pyrometallurgy, the solidification of slags influences the freeze lining behaviour (Campforts et al., 2007) and the cooling of slag after tapping (Durinck, Jones, Blanpain, & Wollants, 2008). Modeling of silicate melt crystallization is frequently done on the macroscopic level, using thermodynamic equilibrium calculations to determine the fractions of all phases as a function of temperature. The Factsage software and database package (Bale et al., 2016, 2009, 2002) already proved its usefulness in pyrometallurgical applications, for example to model the phase mixture after solidification of a stainless steel slag (Durinck et al., 2008). Crystallization of phases typically results in complex morphologies on the mesoscale, e.g. dendrites or facetted growth. On this mesoscale, the phase field concept has proved to be a very powerful tool (Moelans, Blanpain, & Wollants, 2008) for modeling crystallizing microstructures, because it can treat arbitrarily complex interface shapes with minimal mathematical complexity. In contrast to macroscopic models, the diffusion profiles and crystallization kinetics can be described as well as the morphology of individual crystals. First, Kobayashi (Kobayashi, 1993) simulated a growing dendrite in a pure undercooled metallic liquid. Then, Warren and Boettinger (1995) simulated a dendrite in an isothermal system considering a binary alloy. The extension to multi-phase systems was done by Steinbach et al. (1996). This was further extended by Tiaden, Nestler, Diepers, and Steinbach (1998) to a framework with coupled diffusion and phase field equations in multi-component systems.

Jan 1, 2019

By Isabel F. Barton, J. Brent Hiskey

Chalcopyrite (CuFeS2) is the earth’s most abundant copper ore mineral, but is refractory to leaching with sulfates, chlorides, and other common lixiviants and oxidants. This has led to increasing research into alternative lixiviants for recovering Cu from chalcopyrite. Here, we review the leach kinetics of chalcopyrite in glycine, ionic liquids, and methanesulfonic acid, compared to baseline ferric sulfate and ferric chloride. Glycine (CH2NH2COOH) has long been used in applications such as biocatalysis and electroplating, and has recently been examined as a lixiviant for whole ores and concentrates of both copper and gold. It is nontoxic, biodegradable, and capable of strongly complexing Cu2+. Compatible oxidants are peroxide, dissolved oxygen, and ferric sulfate. Chalcopyrite leaching rate in glycine is chemical reaction-controlled, but the effects of grain size and the reaction orders with respect to lixiviant and oxidant concentrations and mass transfer vary. The use of ionic liquids as a leaching agent for chalcopyrite has been extensively investigated in recent years. This system is based primarily on the use of the imidazolium molecule (C3H5N2), which is a planar 5-member ring structure. This lixiviant has been applied to the leaching of chalcopyrite in the form of pure mineral, concentrates, and ores. Kinetics of ionic liquid leaching of chalcopyrite vary substantially depending on the type and concentration of ionic liquid. Methanesulfonic acid (HCH3SO3) is one of the newest lixiviants available in leaching, having only been examined in the last decade. It has been examined as a substitute for sulfuric acid, since it is less corrosive, is biodegradable, and breaks down to carbon dioxide and sulfate over time. The rate of copper leaching from chalcopyrite by methanesulfonic acid is controlled by diffusion and exhibits a strong dependence on oxidant type and concentration. Despite promising reaction rates and total extraction by some of these novel lixiviants, comparison with baseline ferric sulfate and ferric chloride systems makes it doubtful that any will be commercially viable in the near term. Only at very high reagent concentrations and temperatures, and/or very fine grain size, did any of the systems perform comparably to the much cheaper ferric chloride at extracting Cu from chalcopyrite. Most had similar overall reaction rates and total extraction to ferric sulfate, which is relatively common and cheap. However, the leaching kinetics of these novel lixiviants offer valuable insight into the dissolution behavior of chalcopyrite in various systems.

Jan 1, 2019

By V. Feldman, I. Holl, J. Zampini

"The Renard Mine, 100% owned by Stornoway Diamonds, is located approximately 250 km north of the Cree community of Mistissini and 350 km north of Chibougamau in the James Bay region of north-central Québec. The project benefits from a large and growing resource, good mining conditions, strong social acceptance, a modest environmental footprint, and the development of direct-to-mine road infrastructure. Construction began on July 10, 2014; following the completion of a 946 million CAD project financing transaction. Now completed, the mine is the first diamond mine in Québec, and one of only six in Canada, employing approximately 500 people. First ore was delivered to the plant approximately 5 months ahead of schedule on July 15, 2016. Commercial production was declared on January 1, 2017. In general, the project ramp up has been characteristic of a type 1 McNulty curve. One of the challenges during production ramp-up was a redesign of processed kimberlite dewatering (replacing the dewatering centrifuge with two stages of hydrocyclones and a dewatering screen). A processing opportunity captured by Stornoway was the design and installation of an ore sorting facility which rejected free waste rock from the valuable host rock; kimberlite. Through tackling both challenges and opportunities, Stornoway has realised and is now exceeding their original design tonnage.PROJECT DESCRIPTION Stornoway Diamond Corporation (Stornoway) was established in 2003 resulting from to a plan of arrangement between Northern Empire Minerals Ltd. and Stornoway Ventures. In 2011, Stornoway acquired 100% interest of the Renard Mine. The construction of the Renard Mine began in 2014 and achieved full production in 2017 [1, 2]."

Jan 1, 2019

By Yessica Idrogo, Omar Gómez, Francisco Pérez, Eduardo Yrigoyen

Rock blasting is one of the most important operations in the mining cycle value chain, requiring optimized explosives mixtures to get good results. A new and better strategy, and that which is discussed herein, is to design a new emulsion explosive, which can provide improved characteristics and benefits over and above general types of emulsion explosives. It is therefore critical that this product is functional over a wide range of conditions

Jan 1, 2019

By Tapas Kumar Mukherjee, Sujit Kumar, Sanjay Kumar Singh

This paper dwells on the epic blast conducted at Tata Steel’s captive coal mine in India and the insights drawn from it. Optimal blast design parameters had to be ascertained for operating benches (6.56 yards (6 meters) to 16.40 yards (15 meters)) where shovels and mining pay-loaders are deployed. Better fragmentation and suitable muck profile with controlled vibration levels were the pre-requisites. The landmark blast was carried out at Quarry-AB, West Bokaro on 17th March 2017. The colossal blast was done with 275 US ton (250 tonnes) of explosives poured down 1074 drill holes of 6.5 inch (165 mm) diameter. This blast is unique from the perspective of vibration control as it was conducted near local villages situated beyond 546 yards (500 meters) but within 601 yards (550 meters)) from the blast site. The entire array of preparatory activities had been successfully and impeccably executed within the same day. The optimization was achieved through meticulous coordination between TSL team, M/s Solar and M/s IEL. When a rock is blasted, numerous interactions occur among granular particles which are impacted by rock mass properties, explosives properties, blasting geometry and the detonation timings. Optimized use of resources requires a better understanding of these interactions. Extensive field studies have shown that blast fragmentation and suitable muck profile influences the performance of downstream processes in a mine. Consequently, profitability of whole mining operation can be greatly improved through optimized fragmentation. For arriving at the best blast geometry, several blasts were conducted with differing ‘burden and spacing’ design and charging pattern at various loading benches of the mine. Eventually, the largest ever blast was successfully carried out. This accomplishment is the culmination of the insights derived, confidence built, and expertise evolved through a progression of larger blasts conducted earlier (202 US tons (184 tonnes) and 143 US tons (130 tonnes) respectively) by the same team. All blast parameters were within the recommended level and no adverse impact on nearby structures was evidenced. In-the hole VOD of different explosives was determined and placement of boosters was standardized. The signature blasts were conducted to optimize the delay interval between the holes in a row and between the rows. Blasting parameters were fine-tuned in alignment with the desired fragmentation level and muck pile profile conducive to smooth and expeditious loading and hauling by mining HEMM. Rock fragmentation analyses were carried out using photo-analysis system. The insights gained from this blast would serve as the cynosure for planning and carrying out more such blasts with highly optimized parameters in the future with the intent of improving mining efficiency and productivity

Jan 1, 2019

By Peter Zhang, Daniel Su, Heather Dougherty, Jack Trackemas

"Longwall mining has a significant influence on gas wells located within longwall chain pillars. Subsurface subsidence and abutment pressure induced by longwall mining can cause excessive stresses and deformations in gas well casings. If the gas well casings are compromised or ruptured, natural gas could migrate into the mine workings, potentially causing a fire or explosion. By the current safety regulations, the gas wells in the chain pillars have to be either plugged or protected by adequate coal pillars. The current regulations for the gas well pillar design are based on the 1957 Pennsylvania gas well pillar study. The study provided guidelines for gas well pillars by considering their support area and overburden depth as well as the location of the gas wells within the pillars. As the guidelines were developed for room-and-pillar mining under shallow cover, they are no longer applicable to modern longwall mining, particularly under deep cover. Gas well casing failures have occurred even though the chain pillars for the gas wells met the requirements by the 1957 study.This study presents seven cases of conventional gas wells penetrating through longwall chain pillars in the Pittsburgh coal seam. The study indicates that overburden depth and pillar size are not the only determining factors for gas well stability. The other important factors also include subsurface ground movement, overburden geology, and weak floor, as well as the construction of gas wells. Numerical modeling was used to model abutment pressure, subsurface deformations, and the response of gas well casings. The study demonstrated that numerical models are able to predict with reasonable accuracy the subsurface deformations in the overburden above, within, and below the chain pillars, and the potential location and modes of gas well failures, therefore providing a more quantifiable approach to assess the stability of the gas wells in longwall chain pillars.INTRODUCTIONIn the eastern United States, abundant gas wells have been drilled through coal seams that are being actively mined by longwall mining. The existence of gas wells in the U.S. coal fields, whether active or abandoned, have caused many issues for longwall mining. First of all, any gas well in the mining area has to be located by all possible means. Secondly, the gas wells within longwall panels have to be plugged, as cutting through gas wells will allow natural gas to flow into the active longwall mines. On the other hand, the gas wells within longwall chain pillars or barrier pillars can be left in place if the wells are protected by properly designed pillars."

Jan 1, 2019

By R. M. Reyes, D. Negrete, G. Herrera

First Majestic Silver Corp’s La Encantada Silver Mine is a producing mine with a capacity of 3,000 tonnes per day. The La Encantada team is currently constructing two small-scale caving mines, including the San Javier breccia caving mine. The new mine is constructed within a mineralized breccia body composed of clasts of varying sizes and with very poor rock quality. Due to this poor rock quality, primary and secondary supports are required to support both the development and production stages. Since the proximity of the new mining levels to existing old workings, correct selection of the support system and proper production controls, instrumentation, and monitoring are very critical to maintain the stability of the pillars and fortification elements. An increased ground deformation due to the load transfer during the production stage is expected. This report reviews the primary and secondary support elements used in the different stages of mining, the monitoring of ground deformation, and the steps taken to analyze and visualize the collected data in order to enable the geotechnical team to manage caving stress and maintain pillar stability. INTRODUCTION First Majestic Silver Corp. (“First Majestic”) is a Canadian mining company focused on silver production in Mexico that operates six producing silver mines, including La Encantada Silver Mine (“La Encantada”). First Majestic acquired La Encantada in 2006. La Encantada is located in the northwestern portion of the state of Coahuila, in northern Mexico, in the municipality of Villa de Ocampo. The mine lies in the northern part of the Sierra Madre Oriental physiographic province. The mine location is shown in Figure 1. La Encantada is a producing mine, with a mill processing capacity of 3,000 tpd, and a 4,000 tpd capacity cyanidation leaching circuit equipped to process fresh underground ore and old tailings amenable to be reprocessed. The mine is currently employing several mining methods, including overhand cut and fill for narrow veins, small mantos, and other minor deposits. A subset of caving methods are applied on the larger, but weak, mineral deposits, such as at the San Javier breccia and La Prieta breccia. La Encantada consists of vein, manto, breccia pipe, and chimney deposits with concentrations of silver, lead, iron, and zinc in oxidized mineralization enclosed by calcareous sedimentary formations of Cretaceous age. At deeper levels, there is sulphide mineralization in skarn with zinc and silver concentrations associated with a granodiorite intrusion.

Jan 1, 2019

By P. Tukkaraja, K. Katzenstein

"Block caving is one of the most economical and efficient underground mining methods and has gained popularity around the world especially for extracting low grade and massive ore bodies. However, during the extraction of ore from the draw bells, gases trapped inside the cave could emit into the working areas; hence, ventilation plays a key role in operating block cave mines successfully where gas emission is a concern. To design an effective ventilation system for a block caving mine, given the dynamic nature of the caving process, it is necessary to develop airflow characteristic curves (P-Q) for a given cave. This study uses a 1:100 scale physical model with an exhaust fan system, and a Computational Fluid Dynamics model of a block cave to investigate the airflow behavior through the cave filled with broken rock material. From this study, it was observed that the cave airflow resistance increases with the decrease in cave porosity and the particle size.INTRODUCTIONThe block cave mining method is gaining popularity owing to its low cost and high productivity. This study considered a case where this bulk mining method is used for the extraction of an orebody that contains uranium mineralization. During the extraction of broken ore from the draw bells, radioactive gases trapped in the cave zone could be released into the production drifts and could create unsafe working conditions in the mine. Mine ventilation systems play an important role in regulating the migration of radon in working areas. One of the strategies to control radon migration in a block cave mine is to exert negative pressure on the cave zone by using an exhaust fan above the cave zone. In order to select an appropriate exhaust fan system, it is necessary to study the airflow resistance of the cave zone (Loring & Nelson, 2006).Extraction of broken ore via drawpoints creates a void volume inside the cave called the air gap. Air gaps with larger heights can lead to air blasts in a block cave mine should the cave collapse. Besides that, the air gap can also lead to decrease in ventilation system efficiency due to recirculation of air flow and associated shock losses. Air gap height can also have a profound effect on the variation of cave airflow resistance (Erogul et al., 2015, 2017). The knowledge of cave airflow resistance is also important for predicting the intensity of an air blast. Cave airflow resistance is a function of cave properties such as broken rock size, air gap, and porosity inside the cave zone (Baysal et al., 2017). Initially, a scaled experimental model with a forcing system was developed to investigate the airflow behavior through the cave, however, this model couldn’t provide an observable change in the airflow resistance when the cave properties were changed (cave porosity, and airgap) This was attributed to the difficulties associated with forcing system in terms of achieving lower porosity values with the available material (lightweight shipping boxes) for simulating broken rock inside the cave zones, and controlling air leakage from the model (Ajitha et al., 2018)."

Jan 1, 2019

By Haofeng Xie, Lijun Peng, Xujun Mi, Xue Feng, Xiangqian Yin, Zhen Yang, Guojie Huang

The Cu/Al composite wires have been widely used in cable industry. Especially in the development of aerospace, the light weight character of wires is particularly important. The wires are fabricated by a drawing process and heat treatment. Mechanical and electrical properties are measured and analyzed. The bending behavior is studied by scanning electron microscope. INTRODUCTION Cu/Al composite is a typical bimetallic composite that has been used in plenty of fields such as automobile and aerospace. The composite has the advantages of excellent conductivity as well as low weight, which cannot be obtained from single copper or aluminum. Industrial products of Cu/Al composite include Cu/Al composite joints (Uscinowicz, R., 2013), Cu/Al bimetallic sheets (Li, X. et al., 2011), Cu/Al flat bar (Wu, Y. & Liu, X. & Xie, J., 2014) and CCA wires (Ahmed N., 1978). CCA wires refer to the composite wires that copper layer concentrically coated on the surface of aluminum core conductor, implementing solid combination of two metals on the interface and forming an integral. At present, the aircraft cable generally use copper or copper alloy conductor, which makes the wire in the aircraft occupy a considerable proportion due to the large density of copper. Therefore, the use of Cu/Al composite wires instead of copper wires for weight loss, is of great significance to the development of aerospace technology industry. Heat treatment is an indispensable procedure to improve plasticity during cold working process, which is of great importance to preparation of wires (Wang, Q. et al., 2008). During the heat treatment, the Intermetallic Compounds (IMCs) are inevitable formed at the contact area of Cu/Al due to the occurrence of diffusion (Lee, S. et al., 2012). According to the results of former researchers, kinds of IMCs were discovered. Antoine Gueydan (2014) identified the formation of three IMCs (Al2Cu, AlCu, and Al4Cu9) at the interface between copper and aluminum after thermal aging. IMCs have a significant effect to the properties of Cu/Al wires. Bending performance is a vital property for the actual application of wires. The brittle IMCs may create a stress concentration that can cause crack initiation during bending process. This work focus on the mechanical properties of Cu/Al composite wires after heat treatment. The effect of various annealing condition on mechanical and electrical properties are studied, in order to find the appropriate annealing conditions, which produce optimal combination properties of Cu/Al clad composite wires. Bending fracture of composite wires is discussed by morphology observation.

Jan 1, 2019

By T. Crivits, I. Bellemans, V. Cnockaert, K. Verbeken

It is well known that slag foaming can significantly complicate copper smelting processes. This is especially true for unpredictable events that generate large amounts of slag foam during a small period of time. These events are here referred to as eruptions and are typical for certain types of liquid bath furnaces such as modern top submerged lance (TSL) furnaces. A few authors already made the link between over- oxidation of the slag phase and slag foaming. In this work, the mechanism is studied in more detail and explained using the smelter chemistry and the behaviour of dynamic foam formation. Finally, the most influential parameters on the foaming behaviour of the process are presented. INTRODUCTION Copper remains one of the most important metals used in our modern society. In 2017, the annual amount of copper produced worldwide was about 23.5 million metric tons. This makes copper the third most produced metal in the world after steel and aluminium. The majority of this copper was produced by copper smelting, about 19 million metric tons, both from primary concentrate and secondary feed material as reported in ICSG’s World Copper Factbook 2018. In the past, copper smelting was mainly performed using Flash smelting, a technology developed before 1949 (Kojo, Jokilaakso & Hanniala, 2000). Nowadays, this type of smelter is being complemented by other smelter types such as ISASMELT and Ausmelt technologies. These are two types op smelter furnaces, based on the concept of a top submerged lance (TSL) furnace. These two technologies were both commercialized around 1990 (Arthur & Hunt, 2005). It is estimated by Wang et al. (2016) that at this time, both flash and TSL smelters contribute equally to the total amount of annually smelted copper. Flash smelting stays the most important technology for extracting copper from primary sources. TSL furnaces, on the other hand, are more suited than Flash smelters for the recovery of copper from secondary materials. This is because of the different ways that the feed material is inserted in both furnaces. In Flash smelters, the ore and fluxes needs to be fine and completely dry in order to be able to blow the mixture inside the burner area of the furnace. The feed material for TSL smelters show less constrains concerning humidity and particle size. The material is dropped from the top inside the molten bath. As a result, a more complex and flexible feed stream can be processed using TSL smelting (Wood, Hoang & Hughes, 2017). This feature will become more important in the future as primary copper sources gets more scarce and the need for a fully sustainable material cycle increases.

Jan 1, 2019

By X. M. Zhou, T. Wu, He X. N.

"In order to study the support effect of concrete in the surrounding rock of a metal mine, the concrete and surrounding rock were comparatively studied. Firstly, the general situation of the ultra-kilometer deep shaft in Xincheng, surrounding rock and geological conditions are introduced. Secondly, the experimental scheme of material mechanical properties of surrounding rock and shaft lining concrete based on same standard dimension and shape are examined, and the mechanical tests of rock and concrete based on different shapes and sizes are carried out. The study shows that the compressive strength value and elastic modulus of the rock cube are 1.28 times and 1.78 times that of the cylinder, and the Poisson's ratio is 0.77 times. The dimensional effect law of the concrete cube and cylinder test data is consistent with the rock law. However, the test results of the concrete are less discrete than the rock; the test also shows that the strength and elastic modulus of the concrete lining of the main shaft of the Xincheng are much smaller than the surrounding rock that is also used as the concrete aggregate, which indicates that the support of concrete lining in the surrounding rock shaft behaved weakly. Based on the development of the modern NATM rock support theory, it is suggested that the mechanical test standard of artificial support materials should be unified into the mechanics test standard of natural rock, which will help to improve the accuracy and practicality of scientific calculation of geotechnical engineering.INTRODUCTIONConcrete and rock mass are usually attributed to a class of materials called frictional materials or geotechnical materials, of these two kinds of materials, the first is man-maded and the second is natural. The attentive scholar can find that there are many differences in the test criteria for the mechanical properties of the two kinds of materials among different industries or departments, reflecting the differences in their sources, tradition, and the application thoery of material strength among them.There is a situation wordwide, that there are many testing standards of the same material mechanical parameters such as elastic modulus, compressive strength, etc. The cube with a side length of 150 mm is adopted as a common sample in the architecture department in China, while a cylinder with a diameter of 50 mm and a height of 100 mm is as a standard specimen in geotechnical department.Knowing that mechanical parameter values are strongly affected by the the size, shape of specimen and loading rate etc, that is to say the mechanical parameter values of the same material are completely different when obtained from different test with different standards. However, such a problem has been long neglected in geotechnical engineering."

Jan 1, 2019

By J. Brent Hiskey

At present, approximately 80 % of the worlds mine production of copper is achieved by smelting and electrorefining. The principle aim of copper electrorefining is to satisfy the large demand for extremely pure copper. It is remarkable that high quality copper cathodes with the required purity (99.99+% Cu, ASTM B115-10) and structural characteristics (i.e. deposit density and morphological texture) are produced from impure copper anodes dissolved in electrolytes containing a variety of impurities. This is accomplished with the proper control of operating parameters such as: current density; temperature; copper and sulfuric acid concentration; agitation; substrate preparation; and the application of electrolyte additives. The basic elements of the electrolysis of copper have not changed significantly over the past 150 years since the early developments of James Elkington. Importantly, our fundamental understanding of the underlying electrochemistry has advanced considerably. This is especially true regarding our knowledge of the mechanistic role of additives during the electrocrystallization of copper. This is a very complex subject and modern electrochemical techniques and the development of surface characterization and imaging instruments has helped immensely in our ultimate understanding of how additives control the deposit structure and morphology. The purpose of this paper is to review the historical development and application of electrolyte additives in copper electrorefining and to examine our current knowledge regarding their use. INTRODUCTION The first transatlantic telegraph cable was completed in August 1858. Regrettably, this cable failed shortly after the initial connections. After several more failed attempts, improvements in materials and copper quality resulted in successful communication between Europe and America on July 28, 1866. In many ways this hallmark event demonstrated the need for high purity copper. The first copper refinery in the world was commissioned in May 1869 in Pembrey, South Wales by partners Josiah Mason and James Balleney Elkington. (Historical Note). The 1865 and 1868 British patents issued to James Balleney Elkington were the foundation for the first commercial production of high purity electrolytic copper (Elkington, 1865, 1869, 1870). This important achievement was made possible primarily by the invention of the dynamo which was based on the fundamental operating principles advanced by Michael Faraday. A symbiotic relationship between copper refining and the dynamo was henceforth established. The dynamo provided electric current for electrolytic refining of copper and the electrorefining tankhouse provided pure copper which was required for the generation and transmission of electricity.

Jan 1, 2019

By N. D. Wineinger, J. Jodouin

"An Independent Electricity System Operator Industrial Accelerator Program (IESO IAP) case study was completed for a mine in Ontario, Canada by SRK Consulting, Inc. The purpose of the study was to analyze the ventilation system to determine whether and which system improvements could reduce the overall electrical power demand of the mine. Financial incentives are offered by the IESO IAP grant program to help cover the capital costs of these improvements. This study included the completion of a full mine ventilation survey as well as measurement of a full suite of electrical parameters of the surface and underground ventilation fans. After these measurements, a base ventilation model was created and established as the system baseline. Changes to the ventilation system were modeled, and their effects on the power demand were projected. The results of the study showed that several improvements were possible which may significantly improve the efficiency of the ventilation system and reduce mine electricity demand.INTRODUCTIONIn 2017, a ventilation study was conducted in accordance with the Independent Electricity System Operator Industrial Accelerator Program (IESO IAP) at a mine in Ontario, Canada. The IESO IAP is designed to assist eligible transmission-connected Canadian companies operating in Ontario to fast track capital investment in major energy conservation projects. The program will provide financial incentives to encourage investment in innovative process changes and equipment retrofits to reduce electricity consumption on the provincial system and to help companies become more competitive by positively impacting their bottom line. There are now four initiatives under the Industrial Accelerator Program:1. Retrofit2. Process & Systems, including Small Capital Projects3. High Performance New Construction4. Energy Managers – a new initiative under the Industrial Accelerator ProgramWithin the program, companies may propose energy saving changes to their current systems where applicable and appropriate. Companies may then be awarded funding to implement the proposed changes. The program allows partial financial compensation to implement certain energy saving changes that would otherwise not be considered due to high capital costs. For larger projects, such as underground mine ventilation systems, a detailed engineering study must be submitted. This study must detail each energy saving change or measure, its savings, and calculate the financial incentives using the IESO IAP Payment Structure. The payment structure for a project is an amount equal to the lowest of the following (Independent Electricity System Operator, 2015):"

Jan 1, 2019

By C. Matthews, A. Vo

Australia is one of the world’s leading exporters of bulk commodities and the extensive use of sampling equipment is key to the successful management of each mining operation. At the process plant, without a full understanding of the feed, product and tails, it is impossible to fully optimise the performance of the plant, such that the metallurgical balance is often open to error. At the port, a statistically correct, bias free and compliant sampling system is crucial to ensuring exported minerals are reflective of their true value and to avoid penalties. Over the last decade, as a result of the iron ore boom, there has been high demand for reliable, representative and standard compliant solids sample systems in Australia. This paper reviews several solids sampling applications at Australian mine sites, the challenges and experience gained and how the implementation of reliable representative sampling systems has provided better understanding of plant process performance, improved plant control and overall benefits to the operations. INTRODUCTION Mining is the primary contributor to the Australian economy with Australia ranking in the top 4 in economic resources for 21 primary industrial minerals in 2016 (Britt, et al., 2017). Australia is one of the world leaders in the export of the majority of its commodities including gold, copper and iron ore (Britt, et al., 2017). Therefore, a suitable and standard compliant sampling system is essential for evaluating plant performance and content verification. At the mine and at the port, the larger iron ore miners in Australia have developed stockpile models to predict the grade of their ore down to individual blocks of the stockpile. This allows the miner to create the right blend of material for sale to their customers and ensures they are not underselling their product or at risk of penalties for impurities or low grade. As an example, the average difference between the benchmark 62% Fe and low grade 58% Fe fines at the time of this report averaged US $20/tonne according to the Metal Bulletin Iron Ore Index (Fastmarkets MB, 2019). At a shipload of 180kt this would be a variation of US $3.6M. Whilst this is an extreme example, it highlights the economic importance of producing the correct grade product and a recognised representative sample of said product.

Jan 1, 2019

By T. Kho, W. Zhang, M. E. Reed

The control of flash furnace heat balances is critical. Suspension smelting control and stability comes from stable operation of the heat balance, and this leads to a stable reaction shaft exit temperature. A number of flash furnace operations have been reviewed to determine if the application of this approach is beneficial for their operation. The cause and effect relationship between reaction shaft exit temperature with uptake and throat buildup is being enhanced with this work program. Our operating personnel are exposed to the operational hazards of cleaning this buildup from the throat and it is imperative that as an industry we continue to look for repeatable solutions. WorleyParsons has reviewed operational data from a number of flash furnaces and looked at the possible improvements that can be made to decrease variation in the reaction shaft exit temperature. The data assessed for each operation illustrate the need to fully understand the process inputs to the particular operation and to ensure that the control changes are correctly impacted. In the plant data that have been assessed for a number of operations combinations of feed changes and inappropriate process decisions have lead to changes in reaction shaft exit temperature which impact the overall furnace operation and the uptake shaft condition, and ultimately the boiler. INTRODUCTION In 2016 WorleyParsons jointly prepared a paper outlining the effects of heat balance control on the Olympic Dam flash furnace (Reed et al, 2016). That paper investigated the importance of heat balance control in flash furnaces and demonstrated the changes made at the Olympic Dam operation to control the heat balance in the furnace and the impact that change had. The operation is still using the tool to assist in trouble shooting performance and pinpointing problems that may lead to issues in the furnace throat and Waste Heat Boiler (WHB). As a result of the interest in the methodology and due to the issues surrounding safety and process performance caused by WHB throat buildup and damage, WorleyParsons approached a number of flash furnace operators to discuss the application of the approach at their operations.

Jan 1, 2019

By K. J. G Hedges

"Once a health based guidance limits for exposure to diesel exhaust have been established, and as part of a multi-disciplinary team, the program for exposure reduction should incorporate the plan-do-check-adjust cycle. Setting a suitably protective (health based) occupational exposure limit (OEL) for diesel particulate matter (DPM) and nitrogen dioxide is a key driver to reduce exposure. It is important to go beyond regulations and reduce exposure to diesel exhaust, DPM, as low as reasonably achievable (ALARA) such as that prescribed under the Australia, Queensland Mining and Quarrying Safety and Health Regulation 2017 where under section 135 Limiting workers exposure, the workers exposure must not exceed the exposure limit applying to the worker for the hazard; and is ALARA. It appears that previously acceptable OELs are no longer safe. Therefore it is important that the internal responsibility system be implemented and the precautionary principle approach be followed, especially as it may be some time before a suitably protective OEL specifically for DPM is in place. One leading multi-national mining company BHP Billiton has acknowledged a significant lag that exists between regulatory action and the level of science that informs health risk. This company is managing exposure to diesel exhaust to as low as technically feasible. This same company that has set an interim target for managing diesel exhaust to 0.03 mg/m3 is achieving these levels which paves the way for other mining companies and general industry including construction. The Occupational Cancer Research Centre 2017 recommends reducing personal exposure to within 0.02 mg/m3 (EC) for underground mining and 0.005 mg/m3 for other workplaces. Controlling DPM is important to prevent cancer however it is also important that that nitrogen dioxide (NO2) be reduced (ALARA) and that careful selection of control technology be considered such as the proper selection of a diesel oxidation catalyst so that the level of NO2 does not in fact increase. The example from BHP Billiton provides a leading practice including using a multi-disciplinary approach and the importance of controlling emission at source and having an auditable diesel emissions based monitoring program in place."

Jan 1, 2019