Search Documents

By Ryan Weaver, Travis Coleman

The drilled shafts that support transmission lines and substations have been increasingly subject to testing to assess the integrity of placed concrete. Cross-hole Sonic Logging (CSL) has been used, but large diameter shafts with challenging site access are generally more favorable to Thermal Integrity Profiling (TIP) testing. TIP testing assesses the shafts based on measurements of the concrete temperature during curing. The TIP results provide assessment of integrity both within and outside the cage, along with information about the alignment of the cage and concrete cover. This data has allowed shafts with imperfect results to be subject to more detailed structural evaluations. However, it may not be well understood how to use this additional information by designers and engineers. The purpose of this paper is to present TIP results of transmission line foundations, both with and without issues with integrity, including cage shifting, minimal concrete cover, or soil inclusions. The intent is to provide general guidelines of the issues that merit additional investigation and those that should be recognized as inconsistencies inherent to underground construction. BACKGROUND This paper is intended to discuss some of the drilled shaft evaluations made when TIP testing is performed. The authors of this paper were recently involved with a transmission line project that was designed and constructed for a Confidential Utility Client located in the Midwest United States. The project was delivered as an Engineering, Procurement, and Construction (EPC) contract with the electrical line construction company as the prime contractor. The contractor then subcontracted several parts of the work which included engineering for transmission line and foundation design, foundation construction, and third-party testing intended to evaluate the concrete homogeneity and integrity of the place concrete in the deep foundations. The testing method selected was Thermal Integrity Profiling Method B, which uses thermal sensors embedded in the concrete. The TIP testing was administered by Mr. Travis Coleman with GRL Engineers, Inc. Mr. Ryan Weaver with Burns & McDonnell served as the owner’s engineer and technical consultant for the utility and was responsible for reviewing submitted TIP reports and providing recommendations to the utility on their acceptance, and if there were any issues that would warrant further discussion and analysis.

Jan 1, 2019

By Daniel P. Stare, Lucian P. Spiteri, Christopher M. Hallahan, James C. Myers

Buckeye Lake Dam was substantially remediated between 2015 and 2018 as a result of unacceptable dam safety performance. A permanent seepage cutoff, consisting primarily of a soil mixed cutoff wall (SMCW) with occasional sections of steel sheet piling, was constructed along the dam alignment. Closures were required at the terminus of the soil mix elements with existing structures or coffer cells, and at locations where new sheet piling was constructed parallel to the new soil mixed cutoff wall, creating a short circuit seepage path. The original proposed design to construct these closures included permeation grouting methods with chemical grouts. However, a combination of multiple chemical grout types, multiple grout pipes, and an extensive post-grouting verification program was required to ensure the design intent was achieved. After award of the project, the specialty grouting contractor elected to evaluate jet grouting as an alternative closure construction method. The advantages of the jet grouting option offered potential schedule and cost savings to the project as well as a superior product for seepage reduction, given the mixed soil conditions at the site. This paper presents an examination of the site conditions and project goals for the construction of the proposed closure elements for the rehabilitation of Buckeye Lake Dam. Descriptions of the original and alternative treatment methods are provided, with expected performance results. A description of the relative strengths and deficiencies of each method, as well as the feasibility and constructability of each method is provided. The implementation of the jet grouting program is presented, including a discussion of the design elements, quality control test methods, movement monitoring, and verification test methods. This paper also examines the risks associated with jet grouting and how those risks were mitigated during the grouting operations. HISTORY Buckeye Lake is situated approximately 28 miles east of Columbus, Ohio and is managed and operated by the Ohio Department of Natural Resources (ODNR) as part of the Ohio State Parks system. The lake is impounded by natural features that exist along the south and east banks of the reservoir, and by the embankment structure constructed along the north and west banks of the reservoir (see Fig. 1). The reservoir site was originally a natural swamp and the original purpose of the constructed dam and reservoir was to provide water to the Ohio and Erie Canal System. Several dam alignments and configurations were constructed during its early history; however, the original embankment is comprised of homogeneous earthen fill. The embankment is 15 ft (4.6 m) high and extends 4.1 miles (6.6 km) from the North Shore abutment along the east, continuing to the abutment at Lieb’s Island to the West. Several spillway and outlet structures exist along the embankment alignment. Most noteworthy are Seller’s Spillway and Amil Spillway. Fig. 2 is a Plan View of the embankment alignment and appurtenant structures at Buckeye Lake.

Jan 1, 2019

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

New York City is an urban environment with a history spanning over 200 years. The coastline of New York has changed over the years. In the East River, old bulkhead and remnant of relieving platforms together with variable bedrock elevations pose challenges in the design and construction of deep foundations. This paper presents a Case History of high capacity deep foundations along the Franklin D. Roosevelt (FDR) Drive on the Upper East Side in New York City. The project consists of a ramp that overpasses the FDR Drive allowing heavy trucks to access the Marine Transfer Station (MTS) facility built over the East River. Large diameter drilled shafts and mini-piles socketed to bedrock were designed and constructed. Remnant of old bulkhead was encountered at the site and a Ground Penetrating Radar (GPR) investigation was completed during the subsurface investigation phase of the design. This paper discusses details of the subsurface investigation program and design methodology of the high capacity drilled shafts and mini-piles. It also describes construction methods and results of Osterberg Load tests documenting the field values of skin friction through the rock socket. Other construction challenges include construction and drilling rock sockets for drilled shafts over sloping bedrock. 1. INTRODUCTION New York City is a renowned urban city that always calls for the most delicate, yet complex, and robust superstructures and most importantly substructure designs. The historic preservation of this large 200 years old city of 319 square miles is ever changing. Shorelines are often extended to accommodate new infrastructure and very often many miscellaneous structures are discovered below the ground surface. The East 91st Street Ramp was constructed to provide access to the East 91st Street Marine Transfer Station over FDR Drive and York Avenue. Another alternative ramp will be relocated to the South Bound (SD) of the FDR Drive at 92nd Street. A subsurface exploration program was completed in accordance with the New York City Department of Design and Construction (NYCDDC) general requirements, Section 4.5, to perform subsurface investigation along the FDR Drive in Manhattan, New York.

Jan 1, 2019

By Sylvia S. Eskander, Sherif S. AbdelSalam, Mona B. Anwar

Expanded Polystyrene (EPS) geofoam has long been used in numerous geotechnical applications due to its lightweight and durability. Among these applications is the use of EPS as an alternative fill material to conventional roadway soil embankments. This study investigates the benefits of using EPS roadway embankments to reduce the induced stresses and strains on the underlying peat and soft clay. Firstly, mechanical and interface properties of the EPS were acquired from a companion study that also considered the cyclic loading and creep effects. In order to determine the actual stress-strain distribution within the EPS blocks, a physical prototype was developed in this study with overall dimensions of 1.2 x 1.0 x 0.5 m, with a density of 35 kg/m3. The prototype EPS blocks were subjected to cyclic loading with intensities ranging from 10 to 50 kN. Then, a numerical model was developed to simulate the behavior of EPS roadway embankments. The numerical model outcomes were verified against the prototype measurements. A parametric design study was also conducted to develop a correlation between EPS embankment height and the stress-strain that occur in the underlying strata. Results showed that EPS embankments could reduce stress and settlement in the underlying soil by about 40% and 54%, respectively. EPS APPLICATIONS AND BACKGROUND Expanded Polystyrene (EPS) geofoam blocks have been effectively used during the past several decades in numerous geotechnical applications. EPS static and dynamic properties as well as interface behavior were extensively characterized in various published studies such as that conducted by Horvath, 1994; Stark et al., 2004; Zarnani and Bathurst, 2008; Trandafir et al., 2010; Athanasopoulos et al., 2012; AbdelSalam and Azzam, 2016; and others. However, to be able to use locally produced EPS blocks, its physical and mechanical properties must be thoroughly determined. The lightweight and compressible material of EPS geofoam makes it suitable both as a backfill and for absorbing pressure in both the vertical and horizontal directions. Kim et al. (2010) adopted EPS as an alternative for soil backfill around buried pipes; their model showed a reduction in the vertical stress acting on the pipes by up to 36%. Oshati et al. (2012) presented a case study of a field-instrumented box culvert with EPS blocks on top, which reduced vertical stress by 58%. Meguid et al. (2017) used an EPS inclusion to surround culverts and achieved up to 72% stress reduction, depending on the EPS density and the culvert depth to width ratio. AbdelSalam et al. (2017) used a relatively thin EPS inclusion behind flexible cantilever retaining walls, verifying that the lateral pressure can be significantly reduced by 25%; they also developed a design chart for this application. Moreover, AbdelSalam et al. (2019) investigated the use of EPS as a lightweight alternative for soil backfill above shallow tunnels. It was found that EPS had created a differential movement between the wedge located above the tunnel and the neighboring soils, which accordingly reduced the vertical stress acting on the tunnel by 85%, due to the use of lightweight EPS material and positive soil arching.

Jan 1, 2019

By Barritt Lovelace

Collins Engineers has been researching and implementing the use of drones on Civil Engineering Projects since 2015. Applications include bridge inspection, asset management, mapping, construction site management and emergency response. Recently this technology was used to map and model construction sites with deep foundations to verify and quantify designs. The ability to collect and use large amounts of data is transforming our world. Drone hardware and software is being used to capture and digitally replicate assets, giving owners unprecedented ability to visualize and manage their projects. Our teams help owners collect and process drone data into deliverables to be analyzed, annotated, stored, and shared. The use of drones can transform the way projects are managed and can improve project workflows. Data collected with drones can be processed into a digital twin of any project site or asset. This digital twin provides owners with a three-dimensional geometrically and geospatially accurate model. These models can be annotated and tagged with information that can be stored and shared locally or on cloud-based platforms. The data can be exported and used in a wide variety of CAD and GIS platforms. Goals When considering the use of UAS for several items need to be considered when establishing project goals. Safety Drones can be used to reduce job site safety risks in two ways. The first is that use of the drone can remove personnel from harm’s way. Surveyors and other project staff will traditionally walk the site to collect survey and other site information. These efforts can be replaced with the use of a drone eliminating much of the need for personnel to be on the job site itself which improves safety. The other way safety can be improved is that a digital model of a job site can be created on a daily or weekly basis that can be quickly analyzed for safety hazards. This analysis could be done remotely by safety officers to identify job site hazards which can then be corrected before injuries happen. Improved Deliverables Perhaps the most important reason to incorporate drones into project workflows it the ability to improve the project deliverables. Drones have the ability to quickly collect large amounts of high quality data which can be processed into orthomosaics, point clouds and 3D models that give engineers and project managers the information they need to make better decisions on design or project management.

Jan 1, 2019

By Gerald Verbeek, Erick Baziw

Dynamic soil analysis (DSA) in geotechnical practice is intimately related to the capability of measuring the necessary soil properties of shear modulus and absorption. In DSA the methods of analysis are based upon the stress-deformation response of soils due to imposed shear strains. Typically the soil profile is numerically modeled as linear visco-elastic system. This technique is referred to as the Equivalent Linear (EL) method, and it requires the specification of the input parameters of low-strain (<10-5) shear modulus, modulus reduction, and the equivalent viscous damping ratio, which is directly related to the soil absorption value. Downhole seismic testing (DST) has proven to be a very accurate tool for estimating low strain shear modulus values as long as source wave raypaths are taken into account, especially for near-surface investigations. DST has also been utilized to estimate low-strain interval absorption values. In these cases standard frequency domain absorption estimation algorithms (such as the spectral ratio technique) are utilized where it is assumed that the source waves are traveling along the same travel path, which is obviously not the case for near surface DST investigations. This paper outlines a unique DST absorption estimation methodology, which is carried out in the time domain and takes into account source wave travel paths. 1. INTRODUCTION There is considerable interest in methods of geotechnical in-situ engineering that provide accurate estimates of the shear wave velocity and the associated absorption values in the ground, since these parameters form the core of mathematical theorems to describe the elasticity/plasticity of soils and they are used to predict the soil response (settlement, liquefaction or failure) to imposed loads (whether from foundations, heavy equipment, earthquakes or explosions).

Jan 1, 2019

By Arpana P. Sabu, Themis Vaxevanis, Sissy Nikolaou, Guillermo Diaz-Fanas

Geo-failures from extreme events (landslides, wild fires, earthquakes, floods, etc.) have increased exponentially in recent years around the world and within the USA. When catastrophic failures occur, they usually involve hundreds of fatalities especially in cases of unexpected triggering events, such as large intensity earthquakes or heavy flash floods. Protective actions against identified potential geohazards can mitigate the associated risks and the future occurrences and prevent these occurrences from becoming disasters, targeting the essence of resilience in geotechnical engineering. Imaging and other virtual design and construction tools can be used to identify weaknesses that trigger geohazards and can, in combination with numerical simulations, guide decision making. In spatially distributed problems, 3D visualization and LiDAR-type of technologies are essential in providing geotechnical engineers a deeper understanding of precarious soil zones and support finding appropriate solutions. This paper will present the value of using virtual design and construction technologies though the case study of the Iztapalapa suburb of Mexico, about 20 km southeast of Mexico City. Iztapalapa was developed within irregular topography and has a long history of severe soil subsidence. Following the 2017 Puebla-Morelos earthquake, the town experienced large settlements resulting in extensive damage to the already frail buildings and unregulated infrastructure. The soil subsidence was visualized by mapping available historic and geotechnical data. The visualization helped to identify areas where additional investigations were needed. Additionally, this paper presents a case study of a series of landslides from the 2016 Mw7.8 Muisne Ecuador Earthquake, which demonstrates the advantages of using novel technologies to collect data and create cloud datasets from drones and digital photos to understand and evaluate geo-vulnerabilities in anticipation of an extreme event and during rapid reconnaissance to plan for long-term instrumentation, which can enhance geo-disaster prevention and overall community resilience. INTRODUCTION Iztapalapa is a southeastern borough of Mexico City (CDMX) located within the Mexico Basin (Figure 1). This borough is a densely populated area of CDMX with a total of 1.8 million inhabitants, and has a third of its population living in poverty (Gonzalez-Hernandez et al., 2015) with limited to no access to clean drinking water. Iztapalapa also suffers from high rates of crime, drug trafficking, sex trade and illegal buildings. As the population continues to grow, the already non-regulated and fatigued infrastructure is unable to meet the community needs, especially during and after natural hazard occurrences. The region of CDMX is one of the world’s most seismically active regions that is also exposed to other geo-hazards such as floods, volcanic eruptions, and continuous settlement due to water pumping that has reached 11 meters over the past 100 years (Nikolaou et al, 2019). While the soil subsidence alone has caused significant infrastructure damage in Iztapalapa and throughout the rest of the city, recent earthquakes have also contributed to those damages.

Jan 1, 2019

By Steven R. Ahlfield, Ali Ghandeharioon

A wastewater treatment plant commissioned in 1978 is undergoing a major expansion. Planning various phases of the 8-hectare expansion at this site requires an understanding of the site response during and after construction, and the potential impact on adjacent properties and infrastructure. The expansion project requires nominally 5 m of site grading fill for flood protection. The site is underlain by loose to compact fine sand over firm to very stiff clay stratum that extends to great depths. Ground improvement is required to mitigate the liquefaction hazard in the fine sand stratum, and preloading is proposed to reduce post- construction settlements in the deep clay. Site development and foundation systems for the plant expansion project were evaluated by conducting settlement analyses which accounted for the historic and future site loading and 3-D modeling of soil layers with interpolation between borehole and cone penetration test (CPT) locations. The numerical model was calibrated to match short-term and long-term settlements measured at the plant site. The analyses were carried out to assess the effects of past loading, proposed preload and surcharge heights, lateral extents and durations as well as vibro-replacement ground improvement on post-construction settlements. Two design options were considered for the preload footprint across the site and foundation system for proposed facilities. It is shown that limiting the preload extent and founding some of the proposed structures on deep friction piles reduce the predicted settlements of adjacent infrastructure and result in reasonable performance for the proposed facilities. INTRODUCTION A wastewater treatment plant commissioned in 1978 will be replaced with a new plant on an undeveloped portion of the site to provide wastewater treatment for an expanded service area. The existing facilities must remain in operation until completion of the new plant. The site grade will be raised nominally 5 m for flood protection. The large areal extent of the site grading fill and plant structures will cause stress changes extending to great depths in the underlying soils and result in settlement of the existing and new structures. Historic settlement of the existing facilities has been tolerable for plant operations, but no settlement performance data was recorded during site development and post-construction from 1978 to 2007. Development of the 8-hectare expansion at this site is planned in three phases to reduce the overall construction schedule. Planning for each phase requires evaluating the effects of various site development activities from start to completion of expansion and during the design life (i.e. post-construction period), and the potential impact on existing wastewater treatment facilities and adjacent properties and infrastructure including an adjacent viaduct structure. Figure 1 presents the site plan and three distinct site development phases considered for the plant expansion.

Jan 1, 2019

By William H. Walton, Joel Dellaria, Jeffrey R. Hill

The City of Chicago has a world-renowned skyline and is known for its provocative architecture. The subsurface conditions in the city have allowed for construction of these significant structures. The skyline is supported on caissons as they are called in Chicago or drilled shafts in other locations. Despite the significant strides the industry has made in advancing the drilled shaft, the use of other specialty geotechnical construction techniques like micropiles has not been overlooked in Chicago and the surrounding areas. Micropiles have been utilized to underpin famous existing historic structures like Orchestra Hall any many others. Engineers have used 200 to 600 kip micropiles to underpin compromised, inadequate, or damaged caissons. The paper will discuss the use of drilled shafts, micropiles, and ground improvement over the last 30 years in Chicago using a curated collection of case histories. It will also examine advancing the industry beyond its current technical limitations using these techniques. INTRODUCTION 20,000 years ago, glaciers from the Chicago region left behind sheets of glacial clay till underlain by dense, over consolidated glacial till below: limestone bedrock, found about 100 ft below street level. An unusual feature in this profile is the soft Chicago Blue Clay. Chicago has been called the birthplace of the Skyscraper and drilled shaft foundation, both of which came about in the 19th century. After the Great Fire of 1871, tall new structures were built rapidly and designing a successful foundation was trial and error. The first deep driven wood pile and caisson foundations bypassed the problem layer and found solid support on hardpan till or bedrock below (Schock and Risberg 2013). Once the drilled shaft foundation became acceptable to the Chicago engineering and construction community, building heights and complexity grew dramatically. As the city grew, building foundations were being repurposed. There was also the need to underpin structures for additional loads and shallow foundations for adjacent construction. Hand-dug drilled shafts were an option for some of these restricted access and low headroom sites but a new technique, micropiles, would prove to be the future of retrofit and hard to construct foundations. Micropiles were introduced on a limited basis to the United States market in the 1970s and 80s. In the early 1990s, the Chicago market began to latch onto micropiles and their use has grown significantly as a solution to the most complex foundation problems a maturing skyline has to offer.

Jan 1, 2019

By Michael Shedlosky, Sonia Sorabella Swift, Nina Carney, David Tarasovic

Rigid inclusions were used to support roadway fills and mechanically stabilized earth (MSE) walls for the South Capitol Street Corridor project. The first phase of this two-phase, nearly $1 billion project will include the replacement of the Frederick Douglass Memorial Bridge, including two approach ovals east and west of the Anacostia River, the replacement of the I-295/Suitland Parkway Interchange, and the construction of several traffic ramps. The bridge itself carries over 70,000 drivers daily and is expected to open in 2021. Ground improvement is required over a portion of the project footprint. Within the ground improvement area, the construction includes MSE walls up to 35 feet high and embankment fills up to 28 feet for which CMC rigid inclusions (RIs) were used to mitigate settlement and stability. The proposed construction runs over multiple old, in-service utilities that the project requirements indicate could not tolerate any stress or settlement due to the construction. As such, solutions that spanned the utilities were required. A concrete slab of varying thickness was used to span a fragile 108-inch-diameter sewer pipeline and 48- inch-square-precast-concrete box beams were used to span twin utilities that were buried just a few feet below current working grades on site. Unreinforced RIs were used to support these structures. The center to center spacing of the RIs perpendicular to the pipe run was 26.5 ft for the concrete slab and 62 feet for the precast--concrete box beams. The axial forces on the RIs were up to 267 kips. The RIs were not structurally connected to the slab or box beams. A single-element load test was performed to confirm the load-carrying capacity of the RIs. This paper will focus on the utility protection slab over the twin utilities and provide an overview of the design of the structural and geotechnical solutions and will present the results of the load test performed. INTRODUCTION The new Frederick Douglass Memorial Bridge (FDM Bridge) and reconstruction of the Suitland Parkway/ I-295 interchange (South Capitol Project) is a part of the Anacostia Waterfront Initiative (AWI) Program, whose goal is to transform the shores of the Anacostia River. The existing FDM Bridge is approximately 70-years old and has been classified as “functionally obsolete”. The completed South Capitol Project will improve the multi-modal transportation options, increase pedestrian and vehicular safety and provide additional green space. The proposed FDM Bridge, a rendering of which is shown in Fig. 1, is designed to become a landmark bridge in the Washington, D.C. area.

Jan 1, 2019

By Nicolas Moscoso, Gerald Verbeek, Marcel Bielefeld, Rob van Dorp

Upon recently, most offshore foundations were based on a number of driven piles that were installed with an impact hammer. With the increase in offshore windfarms two major developments have occurred: the shift from jackets to monopiles, leading to increase of the diameter of the foundation piles, and a shift from impact hammers to vibro hammers. As the use of vibratory hammers is becoming more and more common practice, the need for accurate vibro-driving simulation software has increased, which requires that the soil modelling is enhanced to address soil fatigue during pile driving and to predict reliably the soil behavior and resistance during pile driving. In addition pile driving monitoring, which is routine for piles driven with an impact hammer, needs to become common practice. This paper addresses advances in soil modelling that allows more accurate pile driving simulation as well as the application of Vibro Driving Analysis (VDA) or Monitoring (VDM) to validate the simulation results. This is illustrated by a case study of the test pile for the Delft Offshore Turbine project, a 28 m long monopile with a diameter of 4 m that was driven 15 m into dense sand layers using a vibro hammer. After some 6 months the pile was extracted, and pile driving simulations and VDA were done both for the installation and extraction phase. 1. INTRODUCTION At the end of 2017, the total worldwide offshore wind power capacity was 18.8 GW [1]. The vast majority of offshore wind farms are currently in Northern Europe, which together account for over two thirds of the total offshore wind power installed worldwide, followed by East Asia, while developments in North America are still in very early stages.

Jan 1, 2019

By Krishna R. Reddy, Jyoti K. Chetri, Girish Kumar

Geotechnical engineering encompasses a major portion of the civil and infrastructure projects. The large amounts of energy and resources typically used in these projects leads to undesirable emissions and wastes which contribute substantially towards global environmental impacts (e.g., global climate change). This could further include secondary economic and societal issues which are often unaccounted in traditional engineering design of the geotechnical projects. In order to address this issue, it is imperative to integrate the broader environmental, economic and social implications into decisions of a geotechnical project. Recent years have seen a major impetus on life cycle assessment to evaluate the environmental sustainability of the geotechnical designs. However, there are no tools that can quantify the life cycle triple bottom line sustainability of potential design alternatives in a project with holistic considerations towards broader economic (indirect costs and benefits) and social impacts (stakeholder preferences, socio-environmental and socio-economic impacts). This study presents a new framework for quantitative assessment of life-cycle sustainability (QUALICS) for alternative designs in engineering projects. The framework integrates two multi-criteria decision analysis methods namely, the Integrated Value Model for Sustainable Assessment (MIVES) and Analytic Hierarchy Process (AHP), to support decision making on the potential design alternatives. In this study, a brief overview of the framework is presented. A case study demonstrating the use of QUALICS framework is discussed with its application to the sustainability assessment of two deep foundation systems, caissons and piles, over their design life. The technical designs of both systems are developed based on bearing capacity, both primary and secondary settlements, and structural integrity. The results from the sustainability assessment of the two deep foundation systems are discussed, and the most sustainable option based on different stakeholder preferences and site-specific conditions are identified.

Jan 1, 2019

By David N/A Doucet, Colter N/A Angell, William N/A Joa, Kyle N/A Wagner, Catherine N/A Johnson, Marty N/A Langenderfer

The Kingery-Bulmash (K-B) equations are a widely accepted means of predicting air-blast parameters from surface explosive detonations. The parameters predicted from these calculations include incident and reflected pressure, time of arrival, shock front velocity, incident impulse, reflected impulse, and positive phase duration. K-B calculations are based on curve fitting of experimental data and can be used to predict air-blast parameters for explosive weights from less than 1 kg (2.2 pounds) up to 400,000 kg (440.9 US Tons), and ranges of 0.05 to 40 meters (1.9 inches to 131.2 feet). The K-B equations can also determine the parameters for multiple explosive types using scaled distances and relative equivalency to TNT. An experiment was designed to demonstrate if the measured results for incident pressure, time of arrival, shock front velocity, incident impulse, and positive phase duration equal the expected results reported for the detonation of a small quantity of explosive determined by the K-B Calculator. Three surface-detonated 300-gram (0.66 pound) hemispherical charges of Composition C-4 were observed via high-speed imaging and hydrostatic pressure monitoring. The hydrostatic pressure generated from each charge was measured via piezoelectric pressure transducers at a scaled distance of 10 from the charge epicenter, and at elevations of 0.30, 0.61, and 1.22 meters (1, 2, and 4 feet) above ground level. Variances in experimental values from the K-B predicted values were recorded for each measured blast parameter. Time of arrival, which was redundantly confirmed through high-speed imaging analysis and hydrostatic pressure monitoring, showed the highest deviation from the predicted values at more than double the K-B predicted value. This report compares the observed blast parameters from the test series with the expected blast parameters from the Kingery-Bulmash Blast Parameter Calculator. Differences between the experimental and predicted values are reconciled through analysis and discussion of testing conditions, instrumentation setup, and scaling methods.

Jan 1, 2019

By A. Porvali, V. Agarwal, M. Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2•H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can be treated further with NaOH solution to form REE hydroxides. This study focuses on metamodeling of a simulated flowsheet with design of experiments (DOE). Based on literature survey, a process flowsheet was developed using HSC Sim software. The created flowsheet focuses on circulation of solution containing Na+, K+, SO42- ions and impurities liberated in the NaOH treatment of double salt precipitate. The effect of seven parameters (P1-P7) on seven responses (R1-R7) were modeled using central composite design (CCD). INTRODUCTION Nickel metal hydride (NiMH) battery waste can be considered as an urban mineral due to the presence of valuable metals like: Ni, Co and rare earth elements (REE) (Larsson et al., 2013). In NiMH battery waste leaching experiments, sulfuric acid has often been employed as a lixiviant (Pietrelli et al., 2002,Zhang et al., 1999,Rodrigues and Mansur, 2010,Porvali et al., 2018). The key advantages of sulfuric acid are its stability and cost-effectiveness compared to other mineral acids such as HCl and HNO3. However, the usage of sulfuric acid in NiMH battery waste leaching poses simultaneous challenges and advantages. Limited REE solubility can be taken as benefit when recovering REEs double sulfates after solid-liquid separation. However, sodium and potassium hydroxide, present in electrolyte residues in the battery waste, can cause in-situ precipitation already during leaching due to limited solubility, thus decreasing the total REE recovery (Porvali et al., 2018). However, this problem can be circumvented by washing the electrolyte residues off the raw materials. Subsequently, the REEs may be precipitated in bulk as a mixed double salt out from the solution at very low pH with minimal co-precipitation of Ni and other metals. This relatively easy separation method can be extremely advantageous in the case of such a complex solution matrix with relatively high REE concentrations (conc.). Once REEs have been precipitated as double sulfates as per eq. (1) (Porvali et al., 2018), the resulting double salt precipitate lacks applications without further treatment. Direct thermal treatment would generate sulfur dioxide emissions and likely require high temperatures in order to transform double sulfates into REE oxides. Furthermore, the precipitate contains Na ions, which would need to be removed by chemical treatment from the calcined REE product. In the context of circularity of raw materials, it can be taken of a remarkable benefit if the sodium and sulfur present in the double salt could be reused instead of wasting them into the side streams. To that end, in this simulation study, the double salts are converted by dissolution and precipitation to hydroxides which are readily treatable, e.g. with total dissolution and solvent extraction, for further purification (Abreu and Morais, 2010):

Jan 1, 2019

By T. Bednarski, T. McCallum, L. Moya, L. Nsenga, B. Mbao

The accumulation of solids in solvent extraction (SX) circuits can cause problems with the physical and economic performance of the operation. These solids are responsible for the formation of crud, a solid stabilized emulsion containing organic, aqueous, air, and fine solid particles. The build-up of crud in SX settlers can limit SX operation throughput, require plant downtime, lead to higher organic losses, or result in higher aqueous in organic entrainment (all of which can have a significant, negative economic impact). Current practices for crud management are typically reactive. Crud is physically removed after it has been allowed to build to excessive levels in the circuit and processed mechanically using centrifuges or filtration. A new proactive solution has been developed to prevent crud formation and build-up. Low ppm dosage of an additive, ACORGA® CR60, into the pregnant leach solution (PLS) has resulted in reduced crud formation in pilot and commercial scale for a variety of PLS streams. This paper will review results from operations in North America and Africa, covering heap leach, concentrate leach, and agitated leach feeds. INTRODUCTION Crud formation and build-up in solvent extraction (SX) circuits has been a long time topic discussed and claimed to be crucial to the whole hydrometallurgical process (Liu, et al, 2006). Crud formation is present in all SX systems be it copper, uranium, zinc, etc., and Ritcey (1980) defined crud as a stabilized emulsion containing organic, aqueous, and fine solid particles. The ore type and feed composition is a major determining factor of crud formation and typically contains Si, Al, Fe, P, and sulfates (Ritcey, 1980). It typically builds at the interface between the organic and aqueous, but can also be observed as floating crud on the surface of the settler, or bottom crud, which is common to find in circuits treating agitated leach feeds such as in Africa. As crud formation has been unavoidable, many of the current crud management techniques are reactive, allowing crud to form and build in SX circuits. Once it does, it is removed and treated via different mechanical techniques, typically through some type of filtration or three-phase centrifuge, to remove the solids and recover the organic phase trapped within the emulsion (Ritcey, 1980). Automated pumping systems have also been designed and are frequently used in North American operations. The time and capital required to react to crud formation can be an overwhelming aspect to SX operation.

Jan 1, 2019

By Joël P. T. Kapusta

Back in 1995, Air Liquide and Union Minière presented a joint paper at the Copper 95 – Cobre 95 Conference in Santiago, Chile, describing the first full scale plant trials of shrouded sonic injection in a Hoboken converter at the Hoboken smelter in Belgium. Almost a quarter of a century later, the technology known as ALSI, or Air Liquide Shrouded Injection, has been tested or commercially implemented in several copper and nickel smelters. Despite these successes, the copper industry did not adopt it widely in the same manner the steel industry adopted the Savard-Lee tuyere in the 1970s and beyond, not even in the way the lead industry adopted it with the Queneau-Schuhmann-Lurgi, or QSL, process. The development and implementation of bottom-blowing smelting and converting technologies in China in the last ten years, however, changed the industry’s perception that high- and ultra-high oxygen injection in copper smelting and converting was indeed possible under specific process conditions. In this paper, I retrace the key learnings of my journey with sonic injection over the twenty five years from my humble beginnings in my early years with Air Liquide, through plant trials and technology implementation in the late 1990s and into the first decade of the new millennium, and ultimately, to the most conclusive proof that the sonic injection design methodology I established is valid, and the calculation tools I developed are accurate. I conclude by sharing my thoughts about whether the deployment of the Savard and Lee legacy within the nonferrous industry was just a pipe dream or whether it will become a reality. INTRODUCTION In the context of lower quality ores and changing economic markets, copper smelters need to continuously innovate and improve to remain competitive and respect their corporate social responsibility engagements. One avenue towards this business, social, and environmental goal is to increase process intensity while lowering fossil fuel consumption to lower greenhouse gas emissions and reducing process off-gas volumes to better capture As and SO2–laden emissions. I believe high oxygen sonic injection for submerged tuyere copper bath smelting and converting is one technology that can help smelters achieve that goal of higher business, social, and environmental performance. Twenty five years ago, when I discovered that the Savard-Lee tuyere had revolutionized the steel industry (Savard & Lee, 1966; Knuppel, Brotzmann, Fassbieder, Savard, & Lee, 1972), I had a dream — or was it a vision? — that within the first decade of the new millennium, modern copper smelters operating submerged tuyere bath smelting and converting vessels will have implemented high oxygen sonic injection and will be reaping the financial and environmental benefits that the steel industry enjoyed in the 1970s. As we approach the end of the second decade of the new millennium, I have to admit that my dream has been all but shattered as the majority of copper bath smelting and converting vessels today continue to operate under bubbling regime conditions. This mode of operation is archaic, still requires tuyere punching and blows at inherently low enrichment levels, particularly in converting, producing large volumes of process off-gases. Under such operating conditions, regulations and emission quotas for As, SO2, and particulate matter oblige smelters to use not just primary or secondary hoods, but sometimes even tertiary hoods. I vividly recall being told, fifteen or twenty years ago when visiting smelters to promote the application of the Savard-Lee tuyere in nonferrous processes, that implementing sonic injection was not economically viable due to the high cost of compressing air and oxygen. Some of the smelters I visited back then have since mandated their engineering partners to design and build secondary or even tertiary hoods. I cannot fathom how secondary and particularly tertiary hoods, with all of their auxiliary equipment and added ducting, could be more economically viable than purchasing and installing a few compressors, expanding the pipeline network for compressed air and oxygen, and installing a new control valve train to feed sonic tuyeres. Besides, adding hoods does not address the problem of As and SO2-laden fugitive emissions at its source but merely provides a costly mitigation for it by capturing larger volumes of process off-gases rather than reducing these large volumes in the first place. Moreover, hooding does not reduce energy consumption nor does it increase process intensity, two aspects that I believe are critical for smelters to remain competitive and sustainable in a deeply changing market environment.

Jan 1, 2019

By Mahesh Hingorani

Integrity issues for bored cast-in-situ piles have raised the need for the use of non-destructive tests to verify pile integrity and detect possible anomalies in installed pile sections that could adversely affect their serviceability. Integrity inspections performed after installations are often the most reasonable alternative available to assess the shaft quality. The two most common methods are pulse-echo from a small hand held hammer at the pile top, and cross-hole ultrasonic transmissions along the shaft between parallel sonic pipes. While different in technique, each method has its advantages and limitations. This paper emphasizes more on the degree of accuracy of low-strain pile integrity test by comparing the results with cross-hole sonic logging. Reliable data collection and interpretation by an experienced test engineer will reveal the integrity of the pile. Cross-hole sonic logging and low-strain pile integrity testing were both specified as quality control measures for a metro rail project in India. Both cross-hole sonic logging and low-strain pile integrity testing indicated defects in several bored piles. Also minor imperfections recorded by cross-hole sonic logging were observed in low-strain results. The observations of the two test methods are presented and compared for a better understanding of the importance of low-strain test results for any project. INTRODUCTION Cast-in-situ concrete piles are often chosen as a deep foundation alternative where challenging soil conditions exist. Although quality control measures are almost always taken during the installation of the piles, it is often difficult or impossible to confirm the integrity of the pile at this stage, particularly in wet conditions. Because of the relatively high probability of bored piles having anomalies, quality assurance of each bored pile is essential for each project.

Jan 1, 2019

By Christian Hoyme, Jochen Maurer

Most of the current foundation projects are suffering from disconnected information silos. In the first silo there is the planning of the project with corresponding data, presented by paper or digital drawings. Here will Building Information Modeling (BIM) be one of the trends for the future. We will see more and more projects leaving the “old way” of 2D drawings and moving into 3D planning including metadata of the foundations. But even with a perfect BIM model of a jobsite, we are not at final end of digitalization. While execution of the project at the jobsite, a second data silo is evolving. Data collected directly from construction equipment and manual measurements is currently undervalued in most projects. Paper is passed to the equipment operator and major data from measurements on site are noted on paper and digitized afterwards. Automatically collected data is not be used to create site progress reports or similar report. So, the real “data” just flows around without connection to any other data already existing in projects. And then the third silo arises: The documentation of the project. Data collected on paper es reentered to create some basic documentation of the work handed over to the client. Spreadsheet software is still the “tool-to-be-used” to create at least some documentation. Finally, the documentation is not connected to the data created while planning and not connected to the automatically collected data from the jobsite. A connected jobsite in the foundation industry must link these information silos and have to create a full data-workflow from the design through the execution to the as-built documentation. INTRODUCTION Building information modelling (BIM) is currently the most popular term of construction business in Germany and probably all over the world. But as often there are many different definitions out there and everyone has his own definition or at least understanding what BIM is about. But for sure it is the most relevant for the construction industry in the near future. Most popular is the digital twin for the upper structure of a building. In most cases the BIM models just shows the building itself, but there is more to be implemented. For example: projects where a special foundation is needed, BIM should include also the foundation elements with meta data. There are several advantages. Not only the clash detection of anchors, but also the possibilities to check the interaction with neighbor constructions, power lines and so on are a use case. For sure most of the special foundation elements are not relevant for the whole lifecycle of a building. But during construction and later the demolition the information about the hidden elements is important and gives a benefit to all stakeholders. In the future there will be not the question: “What is already in the ground?”. The risk for following construction projects on the same ground will be minimized.

Jan 1, 2019

By Ruth McKeown, Gilson de F. N. Gitirana, Murray Fredlund, HaiHua Lu

The current design standards for the use of anchors in slopes is based on two-dimensional (2D) limit equilibrium analyses. Anchors are considered as discrete loads and the 2D anchor, factored based on the spacing distance, corresponds to extending anchors indefinitely in the third dimension. A three-dimensional (3D) analysis offers a more realistic representation of the problem, including the true discrete nature of the anchor point loads. This paper explores the typical differences between analyzing anchors in 2D and 3D, using four typical conceptual models. Slopes with constant cross sections were shown to be adequately represented by the traditional 2D approach. The maximum difference between 2D and 3D models was 21% and becomes negligible for lower anchor spacing values, as expected. A slope with an external load was analyzed to evaluate critical slip surfaces with lower aspect ratios. Slip surfaces with lower aspect ratios presented higher edge effects that contributed to the stability of the slope. The results indicate that optimum design requires the 3D evaluation of field conditions inducing low aspect ratios, such as concave and convex surfaces, weak layers, and external loads. INTRODUCTION Slopes may be stabilized using a variety of solutions, including anchors. When performing an analysis, geotechnical engineers often follow the traditional two-dimensional (2D), Limit Equilibrium Method (LEM). It is important to understand the consequences and limitations of the assumptions on which the 2D LEM is based. There are numerous studies on anchors that show the importance of considering the actual three-dimensional field conditions. Desai et al. (1986) proposed a three-dimensional procedure based on the Finite Element Method and considering elastoplastic behavior and interface elements, to account for stress and displacement distributions, the relative motion between the anchors and the soil mass, and nonlinear soil behavior. Several important stabilization mechanisms were explained. The role of grout injection was evaluated in terms of the produced normal stresses along the anchor-soil bounding surface. The approach was shown to reproduce adequately experimental tests on a sand, proving realistic stress distributions around the anchor. Nonlinear soil behavior influenced to a large extend relative interface motions. Michalowski (1989) applied an upper-bound limit analysis in 3D to slope stability analyses. Anchors were not specifically considered in this study, but the consideration of locally loaded conditions shed light on important modeling aspects. The manner how the slide mechanism becomes three- dimensional as the slope is locally loaded was demonstrated. This emphasizes the fact that anchors should produce field conditions that require 3D analysis approaches.

Jan 1, 2019

By Charles Roeder, Amy Leland, Dawn E. Lehman

Concrete filled steel tubes (CFSTs) are composite members that are commonly used in many countries today. CFST components are used in the United States, but they are more common in Asia, in part because the connections used in Asia are quite labor intensive and there are not standard connections in the U.S. In addition, US design specifications are prepared by separate groups for structural steel and reinforced concrete structures and so composite systems that use CFST components are not overseen by a single group and as such there are several, conflicting design standards. In the US, steel tubes used for CFST are more slender (i.e., the diameter-to-thickness, D/t, ratio is larger) than some other countries, and labor practices (structural steel labor is different than reinforcing steel labor) also cause potential conflicts in construction. As a result, CFST has had some use in tall building construction in the US, but very limited use in bridge construction. A research program at the University of Washington has been in progress to address many of these issues with an eye towards universal design expressions, simpler, standardized connections and promotion of accelerated bridge construction (ABC). The research has resulted in recent changes to the American Association of State Highway Officials (AASHTO) bridge design specification as well as state departments of transportation (DOTs), which supports the increased use of CFST in bridge pile and drilled-shaft foundations. An experimental research study which investigate the flexural strength, shear strength and connections was conducted. These connections provide good performance under both seismic and gravity loads and address the concerns of US construction. These connections, their design rules and requirements, and their impact on composite behavior and system performance are discussed. These results permit rapid and economical construction of CFST bridge piers, piles and drilled shaft foundations. They encourage the use of more slender and economical tubes, while achieving the benefits of composite construction. INTRODUCTION Concrete filled steel tubes (CFSTs) are widely used for bridge and building construction in Asia, but the use of CFST in bridge construction is limited in the US. The historical use of structural steel and reinforced concrete in US bridge construction have resulted in more developed design expression for those construction methods, which has limited the use of CFST. Bridge construction in the US is inherently different than in Asia because of differences in codes, labor costs and construction practices. As a consequence, design and construction practices that are economical and practical in other countries may not be practical for US bridge construction.

Jan 1, 2019