Search Documents

By I. Zh. Bunin, G. K. Khachatryan, N. E. Anashkina

For optimization of diamond processing technology the influence of nanosecond high voltage pulses on mechanical and technological properties of diamond crystals and kimberlite rock-forming minerals (calcite, olivine, serpentine) was investigated. Using methods of Fourier Transform Infrared Spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), microscopy and mikrohardness measurement the changes of structural, physic-chemical surface properties, and microhardness of minerals as the result of impacts, was studied. Non-thermal impacts caused a decrease of kimberlite rock-forming minerals microhardness in general to 40-66% as the result of surface microstructure destruction which is caused by formation of micro cracks, traces of surface breakdown and other defects. At the same time, the pulse energy impact on natural diamonds led to formation of B2 type crystal lattice microsift defects, elevated concentration of which increases the hardness properties of crystals. The obtained result indicates possibility of applying pulsed energy effects to improve the softening efficiency of diamond-bearing kimberlites rock-forming minerals without damaging the diamond crystals and ensuring their preservation by the subsequent grinding of ores. By IR and X-ray photoelectron spectroscopy revealed that processing by hight voltage pulses causes a change of natural and synthetic diamonds surface functional cover composition. Short-term exposure (~ 10 - 30) leads to detachment and partial destruction of secondary phases mineral films on the surface of natural technical diamonds, increasing floatability and hydrophobicity of crystals. However, with increasing duration of treatment (~ 30 - 150) occurs surface hydroxylation (found by XPS for synthetic diamonds), as a result of diamond surface layer oxidation. The effect of increasing the natural diamonds flotation activity by 14% (from 47% to 61%) was experimentally established as a result of processing diamond crystals with nanosecond pulses (~ 10-50 sec), which indicates the principal possibility of using pulsed energy impacts to intensify the diamond flotation during processing diamond-bearing kimberlites.

Jan 1, 2018

By Camilla Favaretti, Benjamin Turner, Anne Lemnitzer

Pile foundations are extensively used in the construction of various types of superstructures, including tall buildings, bridges, freeways and offshore structures. A fully constrained tip embedment such as a rock-socket offers an attractive solution for achieving significant tip resistance and improving the load-carrying capability of the foundation element. In profiles with very soft surficial soil, rock-socketing often provides the only reliable source of axial and lateral resistance. In preparation of a large-scale testing program on rock-socketed piles at UC Irvine (UCI) geared towards studying the magnitude of shear amplification at the rock-soil boundary of pile foundations, a pre-test model-scale experiment was executed in the UCI Structural Laboratory. The objective of the model-scale experiment was to iterate and validate the test setup, study the influence of important boundary conditions, assess instrumentation techniques and sensor placement, and to gain preliminary insight into the small-scale specimen non- linearity. In addition, this model-scale study provides ample opportunity to compare lateral performance parameters with analytically predicted lateral load behavior using traditional soil resistance functions and limit state analyses and explore new techniques for the derivation of soil resistance functions. The pile specimen had a pile diameter (D) of 10 inches and a total pile length of 125 inches. The pile was embedded in a 40 inch simulated rock socket overlain by 52 inch of medium dense sand (DR~50%). The pile extended 32 inches above the soil surface, where cyclic lateral loading was applied. The pile was installed in a laminar metal frame box with inside dimensions of 39 inches in width (W), 73 inches in length (L) and 86.1 inches in height (H) as shown in Figure 1. During testing, the box was restrained using a rigid bracing system consisting of concrete reaction blocks, wooden braces and steel girders.

Jan 1, 2018

By Haijian Shi, Drew Pizzo

This article focuses on the appropriate application of subsurface investigation methods for transmission structures, which are typically designed to resist lateral rather than vertical loads. Currently, the three methods used most often for the subsurface investigation of transmission structures in the field are the Standard Penetration Test (SPT), the Cone Penetration Test (CPT), and the Flat Dilatometer Test (DMT). Each of these methods has advantages and disadvantages, and each is more applicable to some scenarios than to others. To gain a better understanding of these test methods and the implications of using them for various kinds of applications, a comparison study was conducted in the field in Maryland, for three boring locations. Each boring location was explored using each of the three tests as stated. The results of the tests and lessons learned are presented and compared, and these comparisons show that the three test methods agree on the majority of the findings. The results from each test method were also used to derive key parameters such as the soil friction angle for given foundation designs considered in order to establish a clear basis for comparison. Recommendations for performing transmission structure subsurface investigations are made in order to optimize the use of each method and thereby optimizing subsequent foundation designs. INTRODUCTION For overhead transmission structures, the most important structural requirement for determining the foundation design differs from the requirement for other structures such as buildings and bridges in accord with the conditions the transmission structures will need to withstand. In addition to the ability to bear a given vertical load consistent with its use, the foundation must bear lateral loads arising from wind and other weather conditions. The foundation types used most often for overhead transmission monopole structures include concrete drilled pier, vibratory caisson, and direct embedment. In order to determine an appropriate and even an optimum foundation design for any given set of conditions, an appropriate subsurface investigation method or approach is needed. Currently, the standard penetration test (SPT), the cone penetration test (CPT), and the flat dilatometer test (DMT) are the three most commonly used subsurface investigation methods.

Jan 1, 2018

By D. DePaoli, P. Zhang

"Phosphate ore is one of the most significant secondary resources for rare earth elements (REEs), and Florida phosphate is of particular interest due to its much higher ratio of heavy REEs, especially yttrium. Analyses of numerous samples from different phosphate processing streams in Florida showed that heavy REEs account for about 50% of the total REEs in Florida phosphate with yttrium accounting for approximately 30%. It was estimated that the amount of yttrium from US phosphate processing could meet the world demand for this critical element. This research aimed at recovering both REEs and phosphorus from a phosphate flotation tails. This tails is composed of mainly silica and phosphate with a small fraction of heavy minerals including monazite and xenotime. Since the specific gravity of silica is 2.6 versus 3.2 for phosphate and 4.5-5 for rare earth minerals, pre-concentration of the minerals of interest by gravity separation was investigated first. A pilot scale shaking table was used in this study. One pass gravity concentration achieved a shaking table concentrate analyzing over 600 ppm REEs at about 40% recovery. Flotation of the shaking table concentrate resulted in a product containing 1809 ppm REEs and 26.37% P2O5 with corresponding recoveries of 73% and 82%. Sulfuric acid leaching at 75oC could recover over 60% REE and nearly all the P2O5. Higher REEs (>90%) recovery was achieved by conducting leaching at higher temperature with concentrated sulfuric acid. The phosphoric acid from leaching of the flotation concentrate is of superior quality compared with that generated from regular phosphate rock.INTRODUCTION Rare earths are a group of 17 elements including those of the lanthanum series, as well as the non-lanthanides, yttrium and scandium. These elements have very specific critical uses in a multitude of markets. For example, lanthanum is used as a catalyst in breaking down crude oil to produce gasoline, diesel and jet fuel and neodymium is the core magnetic component in high-strength magnets for electric car batteries, wind turbines and hard disk drives. Rare earths are also essential for many military applications. Many of these applications have no substitute materials and the move to green technologies has dramatically increased their demand."

Jan 1, 2018

By D. G. Eskin

"It is well known that it takes some time for the solid phase to completely dissolve upon melting, especially inside the defects of insoluble particles, e.g. oxides. Until then the oxides remain active solidification substrates in the case of subsequent solidification. It is also known that ultrasonic melt treatment causes grain refinement through activation and dispersion of solidification substrates (one of the mechanisms) and also accelerates the dissolution of solid metal in the melt. In this study we combine these effects and demonstrate that the introduction of an alloy rod into the matrix melt of the same composition results in significant grain refinement, this effect being increased by the ultrasonic vibration of the rod. The achieved grain size is comparable to that obtained by a standard Al–Ti–B grain refiner. All samples were cast using a standard TP-1 mould to enable correct comparison. The effect of the temperature range of the rod introduction, as well as the effect of ultrasonic vibrations are discussed.INTRODUCTION The fact that by introducing solid metal into the melt one can achieve structure refinement is rather well known. As early as in the 1930s–1950s a series of papers and patents have been published, showing the benefits for grain refinement when dissolving solid metal in the melt before solidification (Danilov and Neimark, 1938; Scheil, 1956). Later on this way of structure refinement was developed further and dubbed “suspension casting” or introduction of “internal chills” (Madyanov, 1969; Zatulovsky, 1981). The solid metal was added in a form of cut wire, cut sheet, or powder, with the resulting grain refining, elimination of columnar grain structure in ingots and castings of steel, copper and aluminium alloys. The underlying mechanisms have been suggested as (1) rapid cooling of the melt due to the latent heat consumption upon melting of the solid metal with the resultant melt undercooling and (2) introduction of many solidification substrates in the form of crystal fragments and active non-metallic inclusions (Danilov & Neimark, 1938; Balandin, 1973). A number of patents have been filed where either the same solid alloy or a master alloy with additions (e.g. Ti for Al alloy) is introduced in the amounts up to 50% (typically less than 10%) into the melt close to the liquidus temperature (Schmidt, 1966; Talbot & Soller, 1973, Krupp, 1974; Bondarev, 1979). The main reason that this technique is not widely used in industry is the possible incomplete dissolution of the solid parts introduced into the melt with ensuing inhomogeneous as-cast structure and potential defects. Also the selection of the temperature range where the technology works the best is not clear."

Jan 1, 2018

By Tingting Li, Guodong Li, Dezhou Wei, Cong Han, Shuling Gao, Yanbai Shen

"The aim of this study is to solve the problem of tungsten leaching from scheelite concentrate using sodium hydroxide in the presence of phosphate by an autoclaving process, which is one of main development techniques for tungsten recovery. To understand the applicability and leaching performance of tungsten leaching from scheelite concentrate, the main work is to investigate the effects of leaching parameters such as initial concentrations of NaOH and Na3PO4, reaction temperature, stirring speed, liquid-to-solid ratio and reaction time on WO3 dissolution rate to obtain the optimal leaching conditions. The chemical composition and phase composition of the samples were evaluated by means of XRF and XRD. The content of WO3 in the leaching residue obtained via washing, filtering and drying was analyzed by thiocyanate spectrometric method. The optimal leaching conditions were found to be NaOH concentration of 6.76 mol·L-1, Na3PO4 concentration of 1.35 mol·L-1, reaction temperature of 180°C, stirring speed of 400 rpm, liquid-to-solid ratio of 2.0 and reaction time of 90 min. The results showed that tungsten leaching rate of 99.20% was reached under the optimal conditions. The technology exhibited superior leaching performance, which not only reduced the consumption of sodium hydroxide but also greatly decreased reaction time in comparison to a conventional autoclaving process. INTRODUCTION Tungsten is an important strategic metal, which is widely utilized in a variety of industries due to its high melting point, superior mechanical properties and heat-resistant performance [1-3]. The chief raw materials for the production of tungsten in nature are wolframite and scheelite [4, 5]. Among them, approximately two-thirds of the tungsten reserves contain scheelite deposits in the world [6, 7]. With the progressive exhaustion of high-quality wolframite resources, scheelite has become a predominant primary resource for the production of tungsten [8, 9]."

Jan 1, 2018

By Timothy J. Matthews, Timothy J. Batchler, Ted M. Klemetti

"From 2011–2016, there were 1,511 documented injuries, including 7 fatalities, from ground falls in underground coal mines in the United States. The majority of these ground-fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely used in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program using the Mine Roof Simulator (MRS) in Pittsburgh, PA.The load-displacement characteristics of an 8-ft x 12-ft panel of 8-gauge welded screen were evaluated using a newly designed, large laboratory screen test frame with multiple load pull locations. This screen was tested in a configuration that simulates current installation practices in U.S. coal mines. In this study, the effects of varying the number and position of the load pull location on the screen performance were evaluated. Ultimately, the type of information obtained in this and similar studies can be used to aid in developing wire roof screen design criteria and to assist mine operators in the selection and use of roof screen in underground mines.INTRODUCTIONThe large majority of ground-fall injuries are caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Compton et al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program in the Mine Roof Simulator (MRS) in Pittsburgh, PA."

Jan 1, 2018

By A. A. Lavrinenko, N. I. Gluhova, L. M. Sarkisova, D. V. Makarov

"The purpose of the study is to study the feasibility of using sodium diisobutyl dithiophosphinate (DDP) to enhance the recovery of platinum group elements from low-grade refractory copper-nickel ores characterized by a portion of nickel and platinum group elements (PGEs) locked in the dominant sulfide mineral — pyrrhotite. These ore characteristics dictate the need to produce a bulk PGE-containing sulfide concentrate due to the difficulties of producing selective concentrates without a significant loss of the metals.New data on the adsorption and flotation performance of DDP-containing collectors were obtained by measuring the electrode potential, hydrophobicity of the sulfide mineral surfaces and by means of extraction spectrophotometry and flotation studies. The interaction between DDP, pyrrhotite, and pentlandite leads to the formation of surface hydrophobic layers consisting mainly of disulfide and a small amount of metal compounds. These adsorption layers are formed by the reaction with butyl xanthate. In the case of cooperite, DDP reacts with the surface, forming not only disulfide, as in the case of butyl xanthate, but also a complex platinum compound. DDP-containing agents demonstrate stronger collecting properties with respect to sulfide minerals of copper-nickel ores compared to butyl xanthate, which is explained by a stronger hydrophobizing effect and foaming properties.The addition of a combination of DDP-containing agents and butyl xanthate at a ratio of 3:1 for the recovery of sulfides and PGEs in the bulk flotation of copper-nickel ore made it possible to improve the recovery of Ni, Pt, and Pd by 13.6, 9.2, and 9.4%, respectively, relative to the recovery achieved in flotation with butyl xanthate.Bulk flotation with the addition of a composition of DDP-containing agents and butyl xanthate allows the most complete recovery of all valuable elements and is the only technologically feasible method for processing of lowgrade ores, when it is impossible to produce without loss high-grade selective concentrates suitable for smelting."

Jan 1, 2018

By Martin Langenderfer, Sergii Chertopalov, Catherine Johnson, Vadym Mochalin, William Fahrenholtz

The high temperature and high pressure of an explosive detonation can be used for the production of nanomaterials. The controlled detonation of explosive compositions along with the collection and characterization of reaction products encompasses a process known as detonation synthesis. The primary advantage of the method of detonation synthesis is the possibility for producing monocrystalline nanoparticles with diameters of less than 10 nm. In order to successfully synthesize nanomaterials via the detonation process, it is necessary that the explosive detonation is conducted in a sealed environment. This environment when pulled to a vacuum or purged with inert gas such as argon will reduce the oxidation of detonation reaction products. Detonation synthesis testing is currently being conducted in a 1.8 cubic meters (m3) (64.3 cubic feet (ft3)) ellipsoidal pressure vessel consisting of two interlocking half shells. The testing involves the controlled detonation of cast mixtures of Cyclotrimethylene-trinitramine (RDX) and 2,4,6-Trinitrotoluene (TNT) in conjunction with siliceous compounds to produce nanocrystalline diamond and silicon carbide. Alternative detonation environments including the presence of a cooling medium such as water or dry ice to absorb residual, post detonation, thermal energy and enhance the stability of the materials being produced have improved yield. Modifications to the explosive charge composition have an effect on the type and quantity of materials that can be produced. Doping of explosive charges with various organic and inorganic compounds has shown promise in the synthesis of materials that are difficult or uneconomical to produce through other methods. This paper outlines the process development of detonation synthesis facilities. Preparation of the pressure vessel to create a suitable detonation environment for the production of nanomaterials is examined. Formulation of explosive charge compositions and considerations involving test charge initiation are discussed in detail. Experimental results and analysis from initial testing as well as plans for future research are also evaluated.

Jan 1, 2018

By Zhou Yucai, Zhou Jing, Zhu Yimim

"In this article, research on the beneficiation process for a carbon containing copper-molybdenum deposit in Henan province has been carried out. The elemental composition, mineral composition and relative content, characteristics of embedded and symbiotic relationship, the forms of the copper-molybdenum particlesand their disseminated features, and particle size distribution have been worked out. Flotation behavior of copper-molybdenum mixed flotation and separate flotation in the systems of different collectors and depressants, and the influence of different flowsheets on the copper-molybdenum separation have been investigated by actual ore flotation tests, The separation problem of copper-molybdenum for a carbon-containing copper molybdenum ore has been solved.INTRODUCTION In this paper, technological mineralogy, small experiment of flotation recovery of copper Molybdenum ore, and expansion experiment of mineral recovery of copper Molybdenum ore are introduced. (1) The results of process mineralogyshow that the content of copper is 0.42%, molybdenum is 0.021% in the raw ore, they mainly exist in the form of sulfide, with low oxidation rate. (2) The results of flotation tests show that the combination of butyl xanthate and isopropyl ethylthionocarbamate reagents is effective collector of copper-molybdenum mixed flotation for carbon copper molybdenum, (3) When the grinding fineness is -0.074 mm taking 71%, and regrinding fineness is -0.038 mm taking 85%, the flowsheet of first copper-molybdenum mixed flotation and then regrinding rough concentrate and last separation flotation of copper and molybdenum was adopted, which realized the effective separation of copper and molybdenum for carbon-containing copper molybdenum ore. Good flotation indexes were gained with copper concentrate containing 20.96% copper and copper recovery 90.06%, and molybdenum concentrate containing 46.78% molybdenum with molybdenum recovery 72.68%. (4) The seven days average concentration index of scale-up the continuous dressing experiment is as follows, the copper content in copper concentrate is 20.16% and the recovery is 89.61%; the molybdenum content in molybdenum concentrate is 24.58% and the recovery rate is 74.09%."

Jan 1, 2018

By E. V. Koporulina, I. Zh. Bunin, M. V. Ryazantseva

"We studied the mechanism of structural and chemical transformations of columbite, tantalite, zircon and feldspar surface during the treatment by high – power electromagnetic pulses (HPEMP) using the methods of X - ray photoelectron spectroscopy (XPS), analytical electron microscopy (SEM - EDX), Kelvin probe force microscopy and flotation experiments. According to XPS and SEM - EDX data, major changes in the atoms chemical state of investigated minerals surface are related with formation and modification of functional cover and changing in concentration (% at.) of hydroxyl groups on the mineral surface, leading to increase in the contrast of technological properties of the rare metals minerals. Research has identified the optimal parameters of HPEMP - treatment of rare - earth minerals Npuls ? 104, Ttreatment ? 100 sec. improving the selectivity of the flotation separation of columbite and zircon. The difference in mineral recovery into the froth (? e) before and after HPEMP - treatment was about 11 % and 24.5 %, respectively. No significant increase was observed in the flotation activity of feldspar. This study's findings demonstrate the effectiveness of HPEMP - treatment in inducing a controlled change in the structural and chemical properties of rare - earth minerals and improving the process efficiency for the processing of rougher tantalum - niobium gravity concentrates.INTRODUCTIONThe importance of improving the processing methods of tantalum-niobium ores and concentrates is explained by the mineralogical properties of rare - earth ores. These are properties such as the variable mineral, chemical, and grain size composition, complex morphometric properties, and the dissemination of ore mineral grains of micro - and nanometric size. Iron oxide and hydroxide films on the mineral surfaces neutralize the surface physicochemical and absorption properties of the minerals. Both in Russia and globally, nonconventional (non - mechanical) methods are being developed based on physicochemical, electrochemical, and pulsed energy impacts to improve the efficiency of disintegration and liberation processes of disseminated mineral complexes and to enhance the contrast of the structural, chemical, and technological (floatability) properties of refractory ores. This study is devoted to the investigation of the applicability of high – power electromagnetic pulses (HPEMP – treatment) for the change in the structural and chemical properties of rare - earth minerals and improving of the flotation properties contrast."

Jan 1, 2018

By V. A. Chanturiya

The state-of-the-art of mineral mining and metallurgy industry in Russia is characterized by high demand of nonferrous, rare, rare earth metals, and highgrade coal, on the one hand, and by involvement of natural and technogenic minerals with low content of valuable components, fine (nearly emulsion) dissemination of valuable components and close physicochemical and process properties. This calls for high-productive and ecology-friendly technologies for more efficient mineral beneficiation based on intensification of operating and new methods to extract valuable components from rebellious ore and technogenic minerals, relying on the last achievements of basic sciences, combination of dressing and chemico-metallurgical processes and using advanced pyro- and hydrometallurgical technologies. The transition to a new strategy of processing is only possible based on the new technological–mineralogical appraisal of a mineral raw material. Actually, the process mineralogy has a stock of modern high-resolution physical methods for analyzing composition, structure and properties of geomaterials, inclusive of micro- and nano-levels: - Identification of micro- and nano-size noble metals, and natural and induced formations on mineral surface; - Experimental validation of structural phase and chemical transformation of minerals under different energy input; - Justification of choice and mechanism of interaction between flotation agents and noble metals with complex material constitution; - Analysis of structural, phase and chemical transformations of sulfides and rocks under leaching. Thus, process mineralogy is an informational background for a unified theoretical approach to scientific justification of flowsheets of efficient mineral processing. The article gives a brief review of practices that have found application and proved to be of high economic efficiency. Such practices are: X-ray radiometry and photometry separation (Uchalinsky and Gaisky Mining and Processing Integrated Works of ALROSA); selective disintegration (equipment engineered by Mekhanobr-Tekhnika and IPKON RAS); process selectivity enhancement (IPKON RAS, Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Chinakal Institute of Mining, Siberian Branch RAS, etc.); bacterial gold leaching (Olimpiada MPIW, technologies developed the Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Nezhdaninsky deposit projects, etc.); combination processing at a mining and metallurgy plant (Norilsk Mining and Metallurgical Company, Yaregsky deposit projects and others); processing of waste: overburden, mill tailings, slag, etc. (Kovdorsky MPIW, Svyatogor JSC, Ural Mining and Metallurgical Company, plants designed by the Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Mining Institute of Kola Science Center RAS, Research Institute for Chemical Technologies); water conditioning in mineral dressing circuits (ALROSA, equipment by IPKON, etc.); utilization of process water (ALROSA, Ural Mining and Metallurgical Company, Severalmaz JSC and others). Thus, Russia this time has the academic and engineering background for development of efficient energy-saving technologies for comprehensive advanced processing in accordance with the world’s standards, or even higher in terms of a number of the technologies, which has continually been highlighted by participants of recent international congresses on mineral processing.

Jan 1, 2018

By Kudret Tutuk, Serkan Saydam, Sungsoon Mo

"This paper presents an overview of the floor heave management at the Glencore Bulga Underground Operations and investigates the contributing factors to the behaviour of the floor. The mine experienced a number of major floor heave events in gateroads on development. As the longwall face approached the roadways, the magnitude of floor heave frequently increased, while new floor heave also developed. Furthermore, severe floor heave events took place along the longwall face. The most observed failure mode was buckling. While regular floor measurements were conducted to better understand the nature of the phenomenon, and various measures were considered to control the deformation of floor, the mining height was increased for the predicted floor heave domains, which facilitated effective management of the floor issues. The experience in the mine indicates that mainly high horizontal stresses with greater depths of cover and certain types of floor lithology configuration are likely to contribute to the failures of floor strata.INTRODUCTIONThe Glencore Bulga Underground is located in the Southwest of Singleton in the Hunter Valley of New South Wales, Australia. Blakefield South, part of Bulga Underground, commenced longwall mining in 2010, extracting coal from the Blakefield seam, while the overlying longwall panels were previously mined from the Whybrow seam. The coal seam ranges from 4.5 m to 8.0 m thick with the mining heights varying from 2.9 m to 3.5 m. The longwall panels are 320 m and 400 m wide and up to 3.5 km long.The mine experienced a wide range of floor issues around longwall panels LW7 and LW8, both 400 m wide. For instance, the concrete floor in the travel road failed and lifted as the longwall retreated in close proximity as can be seen in Figure 1. Figure 2 shows the beam stage loader (BSL) buried into the lifted floor, and Figure 3 shows a timber prop distorted due to the movement of the floor. In addition, severe deformation of the floor along the longwall face impeded the longwall operation, as shown in Figure 4."

Jan 1, 2018

By ?. S. Potokin

"In general the electric pulse treatment is composed from two processes – electric pulse grinding and electric explosive (electric discharging) activation. The electric pulse grinding with the effect of selective destruction refers to a major slag fraction, more that 2-5 mm, when a one can see a physical prerequisites for electrical breakdown of the slag particles. The electric pulse treatment of slag is considered as an additional operation in the technological scheme extraction of non-ferrous metals from copper smelting slags in addition with mechanical grinding, flotation enrichment and acid leaching. Studies of the reprocessability of pelletized slag have shown the possibility of higher extracting non-ferrous metals via flotation after electric pulse disintegration (EPD) treatment. By using EPD of slag pellets, it is possible to increase the non-ferrous metal yield to concentrate by 18-24%.INTRODUCTION The use of the explosive effect of the plasma discharge channel at electrical breakdown of a solid at a pulsed high voltage is the physical basis of the electric pulse method of destruction of geomaterials (Vorobiev et al., 1971; Andres, 1995; Semkin et al., 1995). The flowing of a pulsed current in the discharge channel is accompanied by a sharp increasing of plasma’s temperature and pressure, leading to a supersonic expanding of the discharge channel, the formation in the solid of intensive mechanical tension field, spreading of cracks, and eventually, to the destruction of the solid. Fragmentation and grinding of ore and mineral aggregates by electric pulse method due to a number of specific physical mechanisms of power load and crack formation, belonging only to this method, is different by high selectivity of destruction. This ensures better liberation of grains of individual minerals and their better preservation from destruction and less formation of a slurry output. These features creates the prerequisites for a more complete extraction of a useful mineral in the concentrate during ore dressing, to improve the quality of concentrate. In contradistinction to mechanical methods, electric pulse technology does not contaminate the product with instrumental metal, material of lining and grinding bodies. The possibility simply and in a wide range to change the dynamic load character allows to regulate the granulometric composition of the product of grinding, to obtain a narrower class of product size than is possible with mechanical grinding. The product of electric pulse grinding is characterized by less roundness and large specific surface area of grains due to the trait, that a new surface is formed in the process of splitting during the expanding of cracks. The degradation product has increased sorption and reactivity in chemical reactions. Liberation of the mineral inclusions particle better corresponds to their initial natural state in the rock and this is the great importance for the study of mineral raw materials."

Jan 1, 2018

By R. Washnock, P. James

"INTRODUCTION Abstract Tankhouse iron control through application of new treatment technology to mitigate conventional bleeding losses is considered. Implementation is discussed and the treatment economics explored. A representative case is assessed. Treatment benefits and application drivers for specific scenarios are noted. Background Hydrometallurgical ore processing has become a significant metal extraction/production avenue in recent decades. In copper mining; the focus for this examination, around 25% of global primary copper production and nearly 50% of US production result from various hydrothermal leaching extraction approaches coupled to Solvent Extraction/Electrowinning (SX/EW) metal production. Generally such processing is favored over pyrometallurgical processes for lower ore grades and as such is finding growing use and is expected to remain a key processing route looking forward with average world-wide ore grades falling as known ore reserves become exhausted. Target Problem And Motivation In hydrometallurgical processing the production circuit may be thought of as a chain of interlocked recirculation loops (Figure 1). Leaching dissolves the target metal from the ore along with other ore components which contaminate the Pregnant Leach Solution (PLS). Iron is a common component in copper ores and, as a result, occurs fairly ubiquitously in copper Pregnant Leach Solutions (PLS) generated by leaching. Leached components migrate through the production circuit from left to right (Figure 1) through a net combination of chemical and mechanical transport mechanisms. Selectivity at the recirculation loop interfaces tends to retard rejected component migration through the production process. As a result, overall relative contaminant migration fluxes are slower than the target metal (copper) and the contaminants tend to build up relative to copper in the more upstream portions of the processing circuit over time with iron often being a significant contaminant. Further, while copper is continuously removed from the system in appreciable amounts, little contaminant exit occurs and the absolute contaminant amounts and concentrations also increase throughout the EW circuit over time."

Jan 1, 2018

By Euler De Souza

"Underground operation ventilation energy requirements constitute a significant portion of mine energy consumption (40–50%) and total energy costs (25–40%). In general, mine ventilation systems are energy inefficient; the author has found several systems that operate at efficiencies below 65%. This paper presents how engineering design principles can improve the performance and efficiency of ventilation appliances, resulting in reduced power consumption and operating costs. Case studies demonstrate that, by retrofitting ventilation appliances using proper engineering concepts, systems will operate at efficiencies well above common operating efficiencies, resulting in a drastic reduction in costs and base electrical and energy loads.RÉSUMÉ Les besoins énergétiques nécessaires à l’aérage d’une exploitation souterraine représentent une part considérable de la consommation d’énergie d’une mine (de 40 à 50 %) ainsi que des coûts totaux liés à l’énergie (de 25 à 40 %). De manière générale, les systèmes d’aérage d’une mine sont loin d’être écoénergétiques ; l’auteur a trouvé plusieurs systèmes fonctionnant à des rendements inférieurs à 65 %. Cet article présente les principes de conception technique qui peuvent améliorer la performance et l’efficacité des systèmes d’aérage, entraînant une réduction de la consommation d’électricité et des coûts d’exploitation. Des études de cas montrent qu’en les rénovant à l’aide de concepts techniques adéquats, les systèmes d’aérage fonctionneront à des rendements bien supérieurs aux rendements habituels d’une exploitation. Ces rénovations donneront lieu à une réduction considérable des coûts ainsi que des charges électriques et énergétiques de base.INTRODUCTIONIncreasing electricity supply problems in North America have encouraged an industry-wide evaluation of energy consumption, resulting in a more urgent emphasis on energy-efficient design and operation for all energy-consuming systems. Electricity is the main mode of energy supply and the mining industry is affected by the increasing cost of this commodity (Natural Resources Canada, 2017). Ventilation systems normally operate 24 hours per day, 365 days per year, and account for 25–40% of the total energy costs and 40–50% of the electrical consumption of a mine operation (De Souza, 2013). Ventilation engineers are under ever-increasing pressure to reduce ventilation energy consumption and be cost effective."

Jan 1, 2018

By A. Kamali Moaveni, A. Boehm

"The current research study addresses a physical separation process of basic oxygen furnace slag “BOF-Slag” (also called Linz-Donawitz “LD” slag) for the removal of phosphorous. In order to recycle the LD-Slag into the steelmaking process, the physical dephosphorization methods are considered. The systematic geometallurgical investigation carried out on particle classes of decreasing size, which were further subdivided into susceptibility classes, shows intimate intergrowth beyond 40 µm due to slag´s fast cooling rate. Generally, LD-slag is constituted of oxide and silicate phases, among which di-calcium silicate “C2S” dominates. About 0.5 mass% of phosphorous was detected in the LD- slag, which is exclusively situated in the lattice of the C2S. The comparatively high grinding resistance (Rittinger index 12.9 cm²/J) of the LD-slag reflects the energy demand to liberate the phosphorous carrying phase from the iron containing minerals, while separation efficiency decreases in the very fine particle size range. Hence, the conversion of the phase intergrowth pattern was considered alternatively to re-build the mineral phase structure of the material to a separable interlock pattern. Carbon dioxide, as the most convenient substance in the steelmaking plants, was applied to digest the C2S in the presence of water and to reduce the basicity of the slag slurry. As a result of C2S-CO2 chemical reaction, calcite and calcium silicate are precipitated at the surface of the oxide particles and carried between 25% and 75% of the total phosphorous, respectively. Accordingly, the mobility of the phosphorous content phase to the top of the grains serves the possibility to separate the precipitated layer by mechanical attrition process. This paper is focused on the impact of the intergrowth pattern alteration on the slag´s separability characteristics. Moreover, the operating conditions of the carbonization process, such as temperature and pressure, on the deconstruction kinetics of the C2S and the generated products will be considered. INTRODUCTION The steelmaking BOF-Slag is a stony aggregate waste from the steel manufacturing process. The investigated slag by the current research work was provided by voestalpine steelmaking plant in Linz, Austria. The current legislative situation in Austria restricts the historical application of slag as construction material, due to the high level of heavy metals content and corresponded land-filling and transportation costs of slag, therefore the demand for recycling of BOF-Slag to the steelmaking process has raised, as an alternative application. Statistically, voestalpine steelmaking plant produces about 130 kg BOF-Slag per ton of final steel product, which serves annual BOF-Slag production of 700,000 ton, approximately."

Jan 1, 2018

By I. Westermann, K. Marthinsen, M. S. Remøe

"Al-Mg-Si alloys often add small additions of e.g. Mn or Cr, to form dispersoids, which may act as nucleation sites for Mg2Si particles after homogenization. The purpose is to ensure a high density of uniformly distributed small ?’-particles, which can be dissolved during further processing prior to the final age hardening step. However, their density and spatial distribution are critically dependent on the homogenization procedure. It is therefore important to have a robust and reliable method for assessing their spatial distribution. In the present work an existing methodology for assessing spatial uniformity, the Global Shannon Entropy (GSE), has been implemented and evaluated for different dispersoid structures characterized by scanning electron microscopy. This metric is highly dependent on the parameters used, but by careful selection of adequate parameters, it can be effective in detecting non-uniformity. An important weakness with the GSE was identified, and a modification to improve on the ability to differentiate degrees of non-uniformity is suggested. To evaluate the proposed methodology, the effect of heating rate on dispersoid precipitation behaviour during homogenisation of four Al-Mg-Si alloys with different Mn/Cr-content has been investigated. The metric with the new term has demonstrated promising results, and improved the ability to differentiate degrees of spatial uniformity.INTRODUCTION Al-Mg-Si series alloys are the most common aluminium extrusion alloys and are attractive for applications in a range of sectors (e.g. construction, automotive and recently also in consumer electronics), due to their generally good combination of strength, ductility and corrosion resistance. However, their extrudability and end properties depend critically on the alloy chemistry as well as prior processing conditions. Coarse ß-AlFeSi or Mg2Si-particles typically have a detrimental effect on extrudability, while small dispersoid particles may affect recrystallization, grain growth and precipitation of Mg and Si. The strengthening potential in the final age hardening step depends strongly on the amount of Mg and Si in solid solution after extrusion. The manner in which these particles are spatially distributed will decide whether the final product will exhibit uniform properties, and the number density and sizes will determine the extent of the effect. As such, these are important characteristics."

Jan 1, 2018

By Natalia Konstantinova, Kira Mizell, James R. Hein, Georgy Cherkashov, Amy Gartman, Pavel Mikhailik

INTRODUCTION Ferromanganese (FeMn) crusts from Mendeleev Ridge, Chukchi Borderland, and Alpha Ridge, in the Amerasia Basin, Arctic Ocean, are similar based on morphology and chemical composition. The crusts are characterized by two- to four-layered stratigraphy. The chemical composition of the Arctic crusts differs significantly from hydrogenetic crusts from the North Pacific Prime Zone (PCZ; Hein et al., 2013), such as a high mean Fe/Mn ratio (2.6 versus 1.3) and low Si/Al ratio (1.8 versus 4.0), with lower Mn, Ca, Ti, P, Ba, Co, Cu, Ni, Pb, Sr, and Zn and higher Si, Al, Mg, As, Li, V, Sc, and Th. Based on Arctic FeMn crust mineralogy, chemical composition, and growth rates, crust formation was dominated by three processes: Precipitation of Fe-Mn (oxyhydr)oxides from ambient ocean water, sorption of metals by the Fe and Mn phases, and fluctuating but large inputs of terrigenous debris (Konstantinova et al., 2017; Hein et al., 2017). The Mn and Fe phases are hydrogenous and reflect bottom ocean-water chemistry and the aluminosilicate phase contains stable detrital minerals such as quartz, feldspars, zircon, monazite, and clay minerals. A precise method of studying the distribution of elements in FeMn crust phases is sequential leaching that dissolves four mineral phases of different stability step-by-step, in the following order: easily leachable phase, mostly bio-calcite; manganese oxides; iron oxyhydroxides; and residual aluminosilicate minerals (Koschinsky and Halbach, 1995). Twelve bulk crusts and crust layer samples obtained from six hydrogenous FeMn crusts were studied. Those crusts were collected during Russian (Arktika 2012) and USA (HLY0805, HLY0905, and HLY1202) research cruises from different parts of the Amerasia Basin (Mendeleev and Alpha Ridges, Chukchi Borderland). Samples were chosen for the sequential leaching experiments based on their morphology, location, and water depth. Hydrogenetic crust (D07-33) from the Tuvalu EEZ, central-west Pacific Ocean, was included in the experiment for comparison. Recovery during the four-step sequential leaching, with respect to the bulk analyses, was between 80% and 120%.

Jan 1, 2018

By M. Fig, J. Brune, C. Strebinger, G. Bogin

"A fundamental understanding of flame propagation characteristics through and around obstacles is needed to accurately model methane driven longwall coal mine explosions originating or propagating in the gob. Experimental investigations of methane flames in horizontal cylindrical reactors with simulated gob (i.e. rock piles) were carried out alongside coupled Computational Fluid Dynamics (CFD) and combustion simulations. Stoichiometric methane-air mixtures were ignited in semi-open reactor vessels of 5cm, 9.5cm and 71cm diameter, all with a fixed length to diameter (L/D) ratio of 8.6. This was done both with empty reactors and also with a rock pile placed at the open end of the reactor. The rock pile length to reactor length ratio was fixed at 0.3, and the rock pile height to reactor diameter ratio was fixed at 0.33 for all reactors. The smaller two reactor experiments were modeled with ANSYS Fluent in 2D. Experimental results indicate that for this geometry a similar acceleration mode occurs across scales: that the flame speeds up an average of 40% as it passes over a rock pile with this profile. The model is able to capture several important features of the experimental results, including the significant increase in velocity, the speedup ahead of the rock pile, and the leveling off of the empty tube flame front propagation velocity. INTRODUCTION Explosions in underground coal mines are among the largest industrial explosions, known to result in the rapid combustion of 20m3 of fuel gas or more [1,2] Coal beds hold methane gas under pressure, and when the pressure is relieved through mining activity some of this methane is released. The methane then mixes with ventilation air and, if not sufficiently diluted, may form a combustible mixture, which may result in an explosion. Several large coal mine explosions have occurred around the world recently. These include the 2014 Soma Mine disaster in Turkey that killed 301 people [3], and the 2009 Heilongjiang Mine explosion in China that killed 108 [4]. Other recent mine explosions, including the 2010 disaster at the Upper Big Branch mine that caused 29 fatalities [5], have demonstrated that explosive gases can accumulate and ignite within and around the gob area of a longwall coal mine and then expand into the active mining face and nearby areas, endangering workers and equipment. If enough combustible gas is involved, the initial flame can accelerate, eventually transitioning from deflagration to detonation [6]. Researchers are developing a fundamental understanding of the evolution of the explosion process from the laminar kernel to the fully turbulent regime, and its propagation through obstacles such as those found in the gob. Researchers also studied the initial development of methane flames and the potential for the development of a detonation."

Jan 1, 2018