Search Documents

By M. Abdollahi, M. R. Khalesi, Y. Kianinia, A. Khodadadi Darban

High cyanide consumption during the processing of gold ores with high sulphide minerals can make the typical cyanidation uneconomic. Also cyanide is a toxic material and environmental concerns of cyanide compounds are serious. Optimization of cyanide consumption requires a methodology to estimate the amount of exposed cyanicides, the kinetic of their dissolution and estimation of formation of cyanide complexes which consume the free cyanide. In this paper, a methodology to estimate cyanide consumption by modeling the minerals and gold leaching kinetic based on a liberation model and speciation of all possible cyanide related species in the solution is presented. The results showed that this methodology could successfully estimate the cyanide consumption based on mineralogical data with very lower number of parameters compared to empirical models present in the literature, while it offers the prediction of formation of all cyanide complexes which could be used for optimization purposes.

Jan 1, 2017

By G-L. Wu, X-B. Liu, C-Y. Zhou

"The static recrystallization behaviour of Ti-Nb microalloyed high-strength steel during hot deformation was studied by conducting double-hit hot compression experiments using a Gleeble-3500 thermomechanical simulator. The effects of deformation temperature, strain rate, strain, and initial austenite grain size on the static recrystallization fraction are discussed. The static recrystallization kinetics were modelled, and the results show that the static recrystallization fraction increased with deformation temperature, strain rate, and strain and interpass time. The static recrystallization activation energy Qs was 326.05 kJ mol-1. Comparison of the experimental results and predicted results indicates that the effects of deformation parameters on the static recrystallization in multistage hot deformation are significant. The predicted results are in good agreement with the experimental results. IntroductionIn hot-forming processes, complex microstructures are often induced by multiple hot deformation mechanisms (Zhang et al., 2014; Liang et al., 2015). The softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by the corresponding microstructural evolution (Wu et al., 2010). It is well known that dynamic recrystallization (DRX); metadynamic recrystallization (MDRX), which occurs by the growth of DRX nuclei during intervals of deformation; and static recrystallization (SRX), which occurs by nucleation and growth during the intervals of deformation, can significantly alter the austenite grain size (Chen et al., 2015. Chen, Sui, and Cui, 2014; Mao et al., 2014). The long interpass times allow complete SRX to take place if the steel is being rolled above the interpass recrystallization stop temperature (Tnr), i.e. in the absence of carbonitride precipitation (Siciliano, 2000). In recent research, microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient in achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Bandyopadhyay et al., 2011). The alloying elements Nb, V, Ti are widely used in high-strength low-alloy (HSLA) steel to achieve the desired strength and toughness properties with solid-solution strengthening, precipitation hardening, grain refinement, and dislocation strengthening (Opiela, 2014; Chen and Yu, 2012). The wide applicability of alloying elements in HSLA steel is due to the fact that heat treatments are not required after forming of the parts, which results in time and cost savings."

Jan 1, 2017

By Stephen C. Tadolini, Robert Hawker, Peter Mills, Colin Grubb, Tom Meikle

"In unfavorable strata conditions, it is often necessary to install additional long tendon support as part of a primary support cycle. Although these support systems provide the required additional stability to the roadway installation does have a significant effect on the rate of development. To overcome the slow cure time of Portland cement-type grouts, the use of two component resin systems, such as polyurethanes and urea silicates, have become favorable. However, concerns over low modulus and creep properties has led to the development of a two-component grouting medium that displays the properties of traditional cable grouting materials with the rapid reaction times of pumpable resin systems. This paper describes product testing, application, surface trials, underground trials, and full-scale applications of the Tekthix System in a dynamic underground environment. INTRODUCTION Single-component cement grouts have been used to anchor long tendon supports for many years. They range from high- to low-slump Portland cement and can be slow-setting to fast-setting grouts. However, current cement grouting systems, which includes the grout and equipment, have some disadvantages: 1. Low-slump grouts require pumps that can handle a thick, high-viscosity grout, so choice of pumps is limited. 2. Pumping distance is limited with current cable bolt grout pumps; operators often tend to add water to allow pumping long distance, which adversely impacts the quality and strength of the material. 3. Fast-setting grouts tend to cause issues with pump and line blockages due to the reduced working life of these single-component materials."

Jan 1, 2017

By L. C. So, S. Faucher, S. Mostaghel, D. Sauter, S. -Y. Oh, S. K. Lee

"Molten material from pyrometallurgical furnaces is tapped at high temperature, carrying a large amount of heat. Traditional handling methods of slow air cooling or water granulation do not allow for the recovery of heat from slag and matte. Furthermore, water granulation adds an inherent safety risk of explosions. Recently, there have been numerous studies into processes attempting to recover waste heat. However, most of them have never been commercialized due to numerous challenges including scalability, cost, low heat recovery efficiencies, and difficulties in heat utilization. Ecomaister-Hatch has recently developed and commercialized a reliable and simple dry atomization system that allows for heat recovery while eliminating the use of water. Comparisons of pilot and commercialized dry atomization and heat recovery technologies will be presented and challenges of these technologies will be highlighted.INTRODUCTION Slag has traditionally been regarded as an undesired waste product from smelting operations with slag management focused on removal and disposal of “waste”. Over 500 million tonnes of slag are produced per year, carrying with it ~220 TWh of energy (Barati, Esfahani, & Utigard, 2011). Depending on the process, the energy content of slag ranges from 10-90% of the total energy input (Barati, 2011, Rodd, 2010). There has therefore been great interest in recovering energy from slag. Slag handling methods can broadly be classified into three categories: (1) dumping and slow cooling, (2) wet granulation and (3) dry granulation. As discussed below, only dry granulation routes are amenable to heat recovery. Slag dumping involves the slow cooling of molten material and crushing of the resulting solid. In this process, slag is dumped on the ground directly from furnaces or transferred to slag pots that are moved by rail or haulers and then dumped on the ground. The molten material is left to cool and solidify until it can be broken and handled by heavy machinery."

Jan 1, 2017

By E. Kumar, L. A. Kumar

"A methodology is proposed to develop an optimization model to understand the impact of transporting minerals, from mines to the final destination, on air quality. Recently, there has been increasing concern about the combined effects of multiple activities over many years, and the regional environmental changes brought about by a single project. Environmental issues in the iron ore industry have highlighted the need to broaden the cumulative impact assessment. In this study, we simulated the optimal routes and quantity of materials needed to meet the destination plant demand based upon environment constraints (level of air pollution), as well as the cost of transportation and availability of materials. Multiple scenarios were developed to analyse the effects of changes in routes, alternative transport system (or multi-modal split), traffic congestion, and the cumulative impacts on air quality. The air quality impact zones of the study area were demarcated using a GIS technique. The expected outcome of the study is the selection of a suitable transport system for a particular site with the least impact on air quality, including the transportation route, relative to the minimum cost of transportation of the minerals from the mines to their final destination. The proposed methodology is evaluated with a case study. IntroductionIn India, the process of environmental impact assessment (EIA) has been focused primarily on the local impacts of projects, without considering regional environmental effects. Environmental clearances for proposed projects are based on reports of local impacts. However, any developmental project poses a potential risk to the environment as a whole, and not just in the immediate vicinity of the project. Recently, there has been increased concern about the combined effects of multiple activities over many years—the regional environmental changes due to development of a single project (Dutta, Mahatha, and De, 2004). Environmental issues throughout the country, particularly in the iron ore industry, have emphasized the need to broaden the analysis to include the combined impacts, or those forecast for a proposed region, on an existing environment. The most significant adverse environmental consequences of iron ore transportation are the deterioration of biodiversity and air quality (Kumar and Ajay, 2015)."

Jan 1, 2017

By Yuanfei Chen, Jianfeng Zha

"China is the largest producer and consumer of coal in the world. The mining-induced surface subsidence has bad influences on the surface and structures above the surface. In order to minimize disasters, removal, reinforcement, or maintenance structures are often adopted. In the application of maintenance methods, it is necessary to carry out dynamic surface subsidence prediction to choose maintenance methods, optimize maintenance time, and evaluate the amounts of work. Time series methods and influence function methods are common for dynamic surface subsidence prediction, but the former is difficult to consider with underground mining conditions, and the latter has low prediction precision. Therefore, this paper develops a dynamic subsidence prediction model aided by field-measured data and realizes the model programming. The model could achieve high-precision prediction of dynamic surface deformation through optimizing the parameters in time by using field-measured data of surface subsidence. The research results of engineering cases show that, with the method of dynamic prediction, the standard error can be controlled in the range of 5%, greatly improving the accuracy of dynamic prediction of mining subsidence, which provides strong technical support for the maintenance and management of structures. INTRODUCTION With the rapid economic development and continued industrialization process, the demand for energy is growing in China. Today, China is one of the largest coal, oil, and gas consumers in the world. Coal consumption accounts for 47.7% of the total consumption in the world (Tian, 2016). In order to meet the demand for coal resources in the process of modernization, more and more coal mines carry out coal mining under villages, buildings, highways, and bodies of water. The mining-induced overlying strata and surface subsidence have bad effects on surface and on various structures (such as buildings, railways, highways, high-tension transmission lines) and could even cause various disasters (Williams et al., 1998; Bell et al., 2000; Doyle et al., 2002). Generally, methods, such as removal, reinforcement, or maintenance are taken to eliminate the adverse impacts (Kraatz, 1984; Bell and Genske, 2001; Wang, 1989). When reinforcement or maintenance is selected to remove bad effects, the proper maintenance methods must be chosen. In addition, maintenance time, as well as an evaluation of time it will take to do the work are necessary to predict the surface subsidence with high precision."

Jan 1, 2017

By F. Hees, A. H. Bracken, L. I. Boshoff

"Biological cementation of the Mandena heavy mineral sand deposit in Madagascar was causing difficulty in dredge mining and hence in planning and control of production rates. An investigation was initiated to better evaluate the geotechnical properties of the orebody by defining the distribution and geotechnical properties of the cemented strata, in order to generate a site-specific geotechnical model for the deposit. The geotechnical characterization was developed by an integrated approach using several ground investigation techniques such as piezocone (CPTu) testing, geotechnical drilling, standard penetration testing (SPT), as well as laboratory testing. The final outcomes of the investigation included a 3D geotechnical model showing the distribution and extent of the cemented areas, as well as the typical geotechnical parameter ranges associated with each of the defined geotechnical units. The interpretations developed were incorporated into the mine and production planning to ultimately optimize operational planning and control.IntroductionQIT Madagascar Minerals (QMM) is a heavy mineral sand mining operation at Mandena, near Fort Dauphin in Madagascar. During the final planning and commissioning stages of the project, the need to fully characterize the unusual geotechnical conditions was identified and a geotechnical investigation became necessary.Nature of the problemDuring the commissioning phase it was found that mining production was being hampered by biologically cemented/indurated layers encountered within the sands. Closer inspection of the indurated horizons in the dredging face revealed that these layers contain a high loading of bacteria and fungi. It appears that the bacteria produce an extracellular (outside the cell) polysaccharide (i.e. sugar and carbon salts), which form a gelling biofilm to trap nutrients. There are a number of different bacteria. The fungi, on the other hand, produce a network of fibrous strands that bind the sand grains together. Thus both bacteria and fungi probably contribute to the ‘apparent cohesive’ strength or binding of the indurated sand (Lynn, 2008)."

Jan 1, 2017

By Martin McKinnon, Guy Reed, Russell Frith

"It is arguable that the development of reinforcing roof bolting systems has largely stagnated in recent times, primarily due to the prevailing industry view that few, if any, further improvements can be made to what currently exists. However, this paper contends that reinforcing roof bolting systems can be further refined by considering both the specific manner by which horizontally bedded roof strata loses its natural self-supporting ability and the specific means by which reinforcing roof bolts act to promote or retain this natural self-supporting ability. The Australian coal industry insists on minimising bolt-hole diameter to maximise load transfer and on targeting full-encapsulation by any means necessary. This has led to a significant, albeit unintended, consequence in terms of overall roof bolting effectiveness, namely increased resin pressures during bolt installation and the associated potential for opening bedding planes that may have, otherwise, remained closed during the bolt installation process. Given that the natural self-supporting ability of roof strata is strongly linked to whether bedding planes are open or closed, logically, minimising resin pressures should be a significant benefit. This paper focuses primarily on three key issues that relate directly to the function of the roof bolting system itself: (i) the importance of proper resin mixing in the context of maximising load transfer strength and stiffness, (ii) the importance of minimising resin pressures developed during bolt installation, and (iii) the importance of maximising the effectiveness of the available bolt pre-tension. All mine operators should be invested in improving the individual effectiveness of each installed roof bolt, even by relatively small incremental amounts, so this is an important topic for discussion within the mining community."

Jan 1, 2017

By Bora Okumusoglu, Devon K. V. Mothersille

"AnchorTest is an innovative software package, specifically developed for tablets, that permits ground anchor test data assessment and management in real time. The solution has two components: a front-end tablet app runs on the Apple iPad platform, and a back-end Cloudbased system running on Amazon Web Services with an online cross-platform website, which can be accessed from any PC, tablet or even mobile smartphone. This tool provides full data analysis and data management capabilities and portability to create greater efficiency in the anchor testing process. AnchorTest is programmed to accommodate the major international anchor testing codes and incorporates an intuitive user interface, which is revolutionary compared to conventional engineering software designs. The use of this tool creates an environment where the testing of ground anchors has effectively become a paperless exercise with greater efficiency and access to instantaneous feedback on the performance of anchors in relation to established acceptance criteria.Historically, project personnel record and analyze the results from anchor load tests using spreadsheets and a laptop computer and/or on predesigned paperbased test sheets (usually as a backup of the testing). In addition, the processing of the test results is not typically performed in real time as the testing progresses — the calculations and analysis are performed either afterward while still on site (if a field office is available) or after returning to the office. Undoubtedly, on larger projects containing numerous anchors where multiple anchor tests may be performed at the same time, processing, analyzing and accepting the load test data and results can be especially time consuming, which could cause delays to the construction schedule.DevelopmentThe need for a more automated and digitized approach to record, process and analyze the data from anchor load tests was highlighted at a deep basement project for a mixed-use development complex in Moscow, Russia. The diaphragm wall supporting the structure was approximately 1,970 ft (600 m) in perimeter length and about 148 ft (45 m) deep, with an excavated depth of about 82 ft (25 m), which required six levels of single bore multiple anchors (SBMAs). This project provided a challenge to recording, processing and signing off on the data generated from some 3,600 3-unit SBMAs. More specifically, for this project, three hydraulically synchronized stressing jacks were used to stress and proof test each 3-unit SBMA, which resulted in nearly 10,800 data plots of the load-extension tests being generated. This project served as the main impetus in the conceptual design and optimization of AnchorTest."

Jan 1, 2017

By Zbigniew Lubosik, Andrzej Walentek, Stanislaw Prusek, Sylwester Rajwa, Aleksander Wrana

"Underground coal gasification (UCG) provides a solution to supply electricity from high ash coal or deep deposited seams. The coal is consumed in situ, and, accordingly, the ash is left underground. UCG could play a major role in the future of coal, which is expected to fuel 44% of the world’s energy in 2030, in a more environmentally friendly and commercially viable manner. Nevertheless, it is known that the UCG can impact the environment. One of the most important factors in safe UCG process should be the evaluation of rock mass quality and the monitoring of its behaviour. The changes of rock mass parameters and quality have an influence on numerous aspects, such as subsidence and the stability of underground workings in georeactor vicinity, however, they also increase the possibility of pollutant migration through fractures and pores. These issues are especially important in cases of gasification conducted in an operating mine or on areas of high ecological vulnerability. This paper details observations made in two underground trials of UCG performed in Poland recently. The first of which is the Experimental Mine Barbara (under the project entitled HUGE-2 Hydrogen oriented underground coal gasification for Europe – Environmental and Safety aspects, (Wiatowski et al., 2015). The other trial has been conducted at an operating mine, Wieczorek, which is in the framework of a research project on the development of coal gasification technology for highly efficient fuel and electricity production (Czaplicka-Kolarz et al., 2013). During these trials, investigations were carried out aimed at assessing geomechanical parameters of rock mass and support behaviour in surroundings of UCG geaoreactors. Investigation comprises assessment of geomechanical parameters of coal, floor and roof strata, roof displacements, and concrete support strength parameters variation, as well as standing steel support load. Hydraulic penetrometer, endoscopic camera, Schmidt hammer, pull-out method, telltale, and ground penetration radar (GPR) were used in the investigation. Research conducted at both EM Barbara and Wieczorek Collieries revealed that the UCG process did not adversely affected the competency of rock mass (expressed by number of fissures and strength parameters of rocks), the stability of roadways and the support performance in the areas located in the vicinity of the georeactors."

Jan 1, 2017

By B. Drew, K. Budna, C. Wenzl, D. Gregurek, A. Spanring

"The metallurgy of nickel and cobalt and of copper is closely interlinked when processing sulfidic Ni-Co ores and Cu-Co ores. The respective furnaces are typically lined with magnesia-chromite refractories, which are exposed to multiple and complex stresses. The selection of the processing route, furnace type and slag system will be dictated by the specific ore type available, this will determine the individual refractory wear mode. This paper evaluates the common refractory wear mechanisms, namely infiltration, spalling and chemical attack by various slag systems, as well as sulfur attack, as observed when processing primary sulfidic ores. All these wear parameters, which are discussed in this paper, lead to a severe degeneration of the brick microstructure and a decreased lining life. Therefore, a detailed investigation and understanding of the wear mechanisms through “post mortem studies” is an important prerequisite for the refractory producer. Based on such research results, combined with specific process knowledge, appropriate brick lining solutions for nickel and cobalt processing furnaces can be recommended.INTRODUCTION The metallurgical production of cobalt and nickel and of copper is closely interlinked to the mineralogy of the respective ores: cobalt is found in African Cu-Co ores as well as in Co-rich nickel ores (laterites and sulfides). Also, Co-bearing secondary raw materials contain the mentioned elements in different contents. In pyrometallurgical processing of sulfidic ores, cobalt is generally recovered as a by-product during the production of copper and nickel, whereas it is normally not recovered separately during the processing of nickel laterites but remains in the FeNi product. Besides various hydrometallurgical production routes, the pyrometallurgical processes involved comprise smelting (i.e., production of a Cu-Ni-Co-Fe matte in electric or flash furnaces), converting and refining (i.e. removal of Fe and S as well as other elements from matte by oxidation). The ongoing trend to use higher oxygen enrichment in process air enables higher intensity processes but also increases the oxidation potential in the vessel. Therefore, during smelting and especially during the oxidative treatment in converting and refining, some amounts of valuable metals are also transferred to the slag in their oxides form. A subsequent slag treatment is then applied for recovering valuable metals from the slag, namely allowing an economic material stream handling and minimizing metal losses. This is often done in a slag reduction furnace. Additionally, copper and nickel are very good collectors for precious metals and platinum group metals (PGMs) - therefore, depending on the content of these metals, an additional refining process is used to recover these valuable metals from the matte or metal phase (Elvers et al., 1997; Davenport et al., 2002; Crundwell et al., 2011)."

Jan 1, 2017

By D. Sagara, V. G. Makhado

"A model based control strategy was implemented at Loulo Gold Mine in Mali, to stabilise the thickener underflow stream density. This stream acts as the feed to the leaching circuit. pH control of the leaching circuit was integrated with the model-based controller due to slow process dynamics that are not suited to PID control. The controller performance was quantified over a period of 6 months, and was compared to the performance before implementation. The model based controller reduced process variability for both thickener underflow density and pH considerably, and resulted in a reduction in flocculant and lime consumption of 9.32 and 6.55%, respectively. INTRODUCTION Reagent consumption in gold processing plants significantly contributes to the total operational costs. In a typical Carbon-in-pulp (CIP) circuit, the reagent consumption associated with leaching, adsorption, elution and regeneration contribute to approximately 15% of the total operational costs (Stange, 1999). At Loulo Gold Mine, the reagent consumption associated with leaching, adsorption, elution and regeneration contributes to 6% of the total operational costs. As such, a reduction in reagent consumption will present a significant opportunity for savings on operating expenditure. Variability in feed ore characteristics results in continuous changes in steady state operating regions, which presents process control challenges as a result of the long residence times in some of the process units associated with gold processing plants. Overdosing often occurs in the presence of process variability to ensure safe operation and to maintain recovery targets. As a means of reducing reagent consumption and accounting for significant changes in the feed to gold plants, some of the plants have resorted to improving their process control strategies around their circuits. This paper focuses on the implementation of a model predictive based controller at Loulo Gold Mine on their thickener and Carbon-in-leach (CIL) tank to: •,stabilise the thickener underflow density, and •,the CIL tank pH."

Jan 1, 2017

By J. Olson

"A model was developed to use near-infrared (NIR) analysis of pulverized ore samples to estimate the recoverable gold content for ores from the Barrick Cortez Hills underground mine. Current routing practices use a ratio of the cyanide soluble gold content and fire assayed gold (CN/FA) to classify ores as oxide or refractory. Prediction accuracy of the NIR model was equivalent to the CN/FA ratio. Prediction accuracy was improved by combining the CN/FA ratio and the NIR spectra. Bootstrap validation estimates the root-mean-square error to be 9.92% with an estimated r-squared value of 0.893. This model will allow more accurate estimates of the variability in recoverable gold content throughout this mine. These data will aid in building an improved geo-metallurgical model or in making better informed routing decisions during the production cycle.INTRODUCTION The contained gold of an ore available for cyanidation is often related to subtle variations in the mineralogy. It is difficult and expensive to collect enough mineralogical information in order to predict how the variable mineralogy will impact the metallurgical results and project economics throughout the life of the mine or mill. Near-infrared spectroscopy may be an effective tool to rapidly and inexpensively collect discrete, quantitative mineralogical data for minerals that contain transition metal oxides, metal sulfides with semi-conduction properties, rare earth metals, and some chemical groups having di-pole covalent bonds such as carbonates, sulfates, and various types of clays (Hunt, 1977). Near-infrared spectroscopy can be a powerful tool for geo-metallurgical characterization of deposits where the presence of these minerals has direct or indirect relationships to metallurgical results such as grindability, regent consumption, or recovery. Near infrared spectroscopy is a rapid analysis that measures the intensity of reflected light in the near-infrared spectrum. The ranges for the ASD-Panalytical units used in this study extend through the visible spectrum and into part of the UV spectrum, reporting reflection by wavelength from between 350 nm to 2500 nm. Absorption peaks visible in this range are a result of interactions with outer valence elections or chemical bonds. The location and intensity of the peaks vary depending on the chemical composition and crystal structure of a solid indicating the presence and abundance certain minerals (Hunt, 1977; Clark, 1984)."

Jan 1, 2017

By Erik Vlot

"The mining industry has recognized the advantages of high density backfill or ‘paste’, which is typically pumped with a hydraulically driven piston pump. Due to the discontinuous flow of this type of pump, pressure pulsations can occur in the discharge line. Pressure pulsations are an undesired phenomenon in pumping installations for a number of reasons that include: damage to the pumping system; piping and supports; disturbing noise levels; and even safety risks for operators and maintenance personnel.This paper describes an advanced system on the GEHO® piston pumps, which will prevent virtually no pressure pulsations from occurring, rather than merely reducing the already existing pulsations.INTRODUCTIONThe first GEHO® hydraulically driven piston pump was developed in the mid-1970s. It was an industrial design pump designed to operate in the high-standard industrial environment with regards to operating hours per day, duties, maintenance and lifetime of the pump and spare parts. This type of pump has a proven track record and has been further developed for the type of applications that we are describing today. The special feature of this pump type is its ability to pump extremely viscous slurry with solids content of up to 90% by weight, at high pressures. Typically, in the mining industry, this pump is used for tailings transportation, with a focus on mine backfill and is often referred to as a paste pump.In the 1980’s the hydraulically driven piston pump made its entry into the application of mine backfill, thanks to the high discharge pressure capabilities enabling the mines to pump higher density (i.e. higher solids concentration) slurries and pastes over longer distances.Part of the ongoing development was (and still is) the increase in discharge pressure and flow capacity to comply with the ever growing demands for high power piston pumps. In line with the technological developments and increase in performance duties, the popularity of this pump type increased significantly and many other industrial applications have discovered the benefits of this pump type.Together with the increase in pump discharge pressures and flow capacities the effect of an undesired phenomenon also increased: the phenomenon of pressure pulsations. Before we explore this subject in more detail it is important to first understand the design and the characteristics of a hydraulically driven piston pump."

Jan 1, 2017

By Allan Herse

"The years following World War II were nation building years in Australia. Soldiers returned from the European and Asian theatres of war sparking a major infrastructure construction boom. Dams and highways were built to keep up with the growth of towns and cities, which were bursting at the seams, not just from the returning soldiers settling down with their families but also from the many waves of refugees from war torn areas around the globe.The demand for electricity generation and distribution required for the growing population sparked the expansion of the national power grid with new high-voltage transmission towers appearing across the landscape. However, with an original design life of 50 years, those transmission lines constructed in the 1950s are nearing, or are at the end of, their anticipated service life.In recent years, the Australian power distribution network has changed from a period of high construction activity in greenfield high-voltage lines to a period that is now focused on reducing cost and maintaining existing assets. Replacing aboveground structural members and electrical components is relatively simple even under live conditions. However, the replacement or repair of tower foundations, many of which are in remote locations, has been a problem that has caused difficulties for power utilities trying to operate on a budget while also avoiding costly and unpopular power outages. With thousands of miles of aging transmission lines needing life extension work, Piling & Civil Australia (PCA) has developed a patented system of upgrading the foundations with micropiles while under live-line conditions without requiring costly outages. The system is seen as revolutionary by power utilities, allowing the utilities to extend the life of their existing assets until demand increases to warrant the construction of a new line. PCA has been working on a potential solution with Powerlink Queensland for the past 5 years to develop a quick and cost-effective foundation replacement system that can extend the life of its existing asset base anywhere from an additional 5 years to 50 years.With design support from Quanta Subsurface, USA, PCA recently completed the foundation replacement of 26 lattice tower foundations in the Townsville region of North Queensland. Using a steel bracket (patent pending) to connect hollow bar micropiles to the lattice towers, the installation techniques that were developed enabled the micropiles to be installed within a tolerance of less than about 3/8 in (10 mm) through the existing steel grillage foundation while maintaining live line conditions. The project was an Australian first and a trial by Powerlink for wider use within its network, and it was delivered on time and within budget at one tenth of the cost of traditional methods."

Jan 1, 2017

By M. H. M. von Wielligh

"Brick manufacturers supply a variety of uniquely coloured facebricks to the building industry, which requires a high level of colour consistency in the products. Colour variation in bricks is influenced by the composition and consistency of the white clay raw material. By blending varieties of naturally occurring white clay the manufacturers produce a unique range of facebrick products. Homogeneity of the white clay raw materials mined at Lenasia is crucial for producing bricks of consistent colour. Geostatistical investigations of the major element distributions (SiO2, Al2O3, Fe2O3, and K2O) and loss on ignition (LoI) were conducted. An analysis of the spatial continuity of these variables followed by ordinary kriging indicated that the upper white clay layer at Lenasia is richer in K2O and Fe2O3 than the lower layer. Consistency in the colour of facebricks depends critically on careful management of the variability in the K2O and Fe2O3 content of the clays. The geostatistical approach to understanding the distribution of elements in the clay allows miners to construct clay stockpiles of consistent quality for feeding the brick-making process. Geostatistical investigation of the chemical contents in other clay domains within the deposit is recommended, and could be extended to all facebrick manufacturers to assist in improving the colour consistency of their products. IntroductionMost clay in South Africa is used in the manufacturing of tiles, pipes, bricks, whiteware, refractories, and pottery. Bricks are manufactured from a wide variety of clay types, the behaviour of which during firing depends critically on the the clay mineralogy and chemical composition, but this relationship not well understood (Stein, 1982). The variety among clay deposits is related to the different processes of formation (Deer, Howie, and Zussman, 1992). The geochemical composition of the clay can vary between layers and within the same layer in an individual deposit (Lurie, 1984). The properties of clay minerals are determined by their structures and the different combinations of silicate layers, cations, and hydroxyl ions (Kingery, Bowen, and Uhlmann, 1976). South African clays can be classified as either kaolinite or montmorillonite and are seldom found in a pure form (Lurie, 1984). Different clay minerals affect the drying, forming, firing behaviour, colour, and quality of the brick product in different ways. Laboratory tests (full physical analysis) can indicate the suitability of a clay for the manufacture of ceramic products. The minerals most essential for the manufacturing of clay brick products are kaolinite, illite, and quartz (Stein, 1982)."

Jan 1, 2017

By Chul Soo Park, Juhyung Lee, Duhyun Baek

"In this study the preliminary design of suction pile as the supporting system of the concrete floating structures was performed at the offshore pilot project area in Korea. The suction pile of the floating structures has to satisfy the lateral resistance against external force evaluated from the marine and structure conditions, as well as the penetration ability according to the soil and seepage conditions. In the design, the required penetration depths for lateral resistance were evaluated with different diameters of cylindrical steel suction pile, and the design suction pressures at each penetrating depths were assessed through the comparison of penetration forces and penetration-resistances. Finally, the optimal dimension of suction pile for the pilot project area was proposed.IntroductionInterests in sea spaces have rapidly increased around the world due to limitations in use of lands. Such increase has resulted in construction of numerous marine structures aimed at expanding the use of sea spaces and developing marine resources. South Korea also needs to secure construction technologies for floating infrastructures on its relatively deep seas. Foundations for floating structures consist of anchors and mooring systems rather than driven piles or cast-in-place piles, due to limitations in equipment operation or economic feasibility. Anchors and foundations used on the sea include drag anchors and suction piles, but the suction piles are more widely used for reasons regarding uncertainties of calculation of bearing capacity and construction. Large-diameter suction piles are generally used to utilize fully their penetration ability, which is proportionate to the square of the foundation diameter, and the length-diameter ratio (L/D) does not exceed 6 (Randolph et al., 2005; Andersen et al., 2005). Recently, a design and construction technology using group suction piles consisting of medium-diameter suction piles and concrete pile caps is being developed as an alternative to the conventional large-diameter mono suction piles. In addition, pilot projects involving the group suction piles of mediumdiameter are currently being reviewed for the southwest coast area in Korea. In this study, therefore, preliminary design for installation of medium-diameter mono suction piles as the supporting system of the concrete floating structures was performed, and suction pressures, penetration forces and resistances, and lateral loading capacity with diameters were reviewed."

Jan 1, 2017

By Ian Bell, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Mahdi Ramezani

"Image-based rock fragmentation sensing in mining and quarry applications includes an important rock boundary delineation step, which is commonly referred to as rock segmentation. This paper presents a novel approach to solve this problem, using artificial intelligence. In the proposed technique, priorknowledge of previously analyzed images is encoded into mathematical/statistical models. A set of human labeled images are used as training inputs. These images are used to train neural networksthrough an optimization process. The networks can then be used in real time for rock delineation. "

Jan 1, 2017

By A. Miura, G. Granata, C. Tokoro, A. Fuwa

"The high copper demand as well as the lack of new high-grade deposits, are pushing the copper industry to process low-grade and refractory ores containing chalcopyrite. However, for a quantitative dissolution of copper from the chalcopyrite, the leaching performances still need to be improved. In the present research, we studied and optimized the iodide-assisted leaching of chalcopyrite in H2SO4-Fe2(SO4)3 media. The evolution of surface species during leaching was determined by x-ray photoelectron spectroscopy (XPS) and mineral liberation analysis (MLA). Inductively-coupled plasma spectrometry (ICP-MS) was used to determine the dissolved copper. Significance of experimental results was assessed by statistical analysis while a kinetic analysis of the leaching process was performed by fitting the experimental data with the Shrinking-core model. Results showed the significant positive effect of iodide on copper extraction rate. In the presence of KI, the dissolution rate of copper was almost double than in the parallel experiments without KI. Whether using KI or not, elemental sulfur was generated on the surface of the leached chalcopyrite. Nevertheless, in the presence of KI, the passivation layer did not arrest the leaching. Analysis revealed that the leaching rate was limited by the chemical reaction control step.INTRODUCTION Due to the large demand of copper, processing low-grade ores containing copper sulfides such as chalcopyrite (CuFeS2) has become unavoidable (Watling, 2013). Since ores with CuFeS2 may also contain appreciable amounts of arsenic that cannot be smelted, and because low-grade ores are uneconomic to smelt, the hydrometallurgical technologies are crucial for recovering the copper (Dutrizac, 1978). Sulfate-based processes are attractive because of the lower operating costs and because the sulfate ion is more suitable in case copper would be recovered via electrowinning. In ferric sulfate solution, chalcopyrite undergoes oxidation due to the large amount of Fe(III) and dissolution due to the presence of the sulfate ion (Majima, et al., 1985). The leaching reaction in ferric sulfate medium can be represented as in (1):"

Jan 1, 2017

By A. Bozorgzadeh, B. M. Jensen, B. N. Koelling, B. R. Murtaugh

"The Service Base mooring system originally consisted of two general types of structures, 19 timber piles cabled together and steel three-legged pipe piles. The St. Louis District fleet moored to the fleet barges which were tied off to shore-side concrete deadman and supported on the landward side by the timber and steel piles. The purpose of this project was to replace the existing floating wharf mooring system at the St. Louis Service Base. The Marine Design Center of the U.S. Corps of Engineers developed a three pile cluster system concept. The clusters consisted of one vertical pile and two batter piles. Piles in rock sockets were selected to resist the uplift loads due to high wind loads on the tall, spare lock gates stored at the floating wharf. This paper focuses on the design of the rock sockets for steel pipe piles with large uplift loads and the lessons learned during the design and construction of this system.INTRODUCTIONBackgroundThe U.S. Army Corps of Engineers’ St. Louis District is located at the critical transition point on the Mississippi River where it is a “locking river” north of St. Louis and an “open river” to the south. The St. Louis District is responsible for maintaining navigation channels on the Mississippi River, the Illinois River and the Kaskaskia River. It is also responsible for the operation and maintenance of five locks and dams within its geographic boundaries.The St. Louis District utilizes a fleet of vessels (dredges, crane barges, motor vessels, and barges) to support the navigation mission identified above. The St. Louis District Service Base, located in St. Louis, Missouri, serves as the base of operations for the district fleet. This riverfront facility originally consisted of a floating wharf, a railroad trestle, and a walkway down the river bank to the floating wharf. Historically, there have been two fleeting areas at the Service Base. The main fleeting area was approximately 965 feet long and consisted of six fleet barges (Figure 1). This area supported the Dredge Potter and its attendant fleet. The upper fleeting area was approximately 1,050 feet long and consisted of various stop log, crane and work barges, dredge pipe pontoons and work flats."

Jan 1, 2017