Search Documents

By John H. Wright

The United States Antarctic Program (USAP), through its principal support contractor Raytheon Polar Services Co. (RPSC), has recently completed a three-year project comprising nearly 936 m (3,071 ft) of undersnow utility tunnels at Amundsen-Scott Station, South Pole, Antarctica. The tunnel serves the new station facilities that are currently under construction. It houses the piping that conveys fresh water from current and future water well sites, as well as waste water to repositories in abandoned wells. The undersnow tunnels permit year-round access for system operations and maintenance. The network of tunnels is entirely unlined and unsupported. And, for the most part, it maintains a rectangular cross section of 1.8-m-wide x 3-m-high (6 x 10 ft).The tunnel runs from 6 to 14 m (18 to 45 ft) below the surface. Eight 1-m- (3.3-ft-) diam raises bored from the surface serve the network as emergency escapeways.

Jan 1, 2002

By W G. Szymczak, Leslie C. Taylor

The University of Maryland (UMD) has conducted a series of small-scale tests using explosive charges buried in saturated sand. Twelve different combinations of depth of burial of the charge and height of the target plate above the soil were tested. The target plates did not deform plastically. High-speed video was used to track the motion of the plate. The video data are analyzed to determine the position and velocity of the plate as a function of time. The results of this analysis are compared with computations performed at NRL using the BUB2D computer code. This code treats the saturated sand as an incompressible visco-plastic fluid which yields according to a Drucker-Prager (frictional-cohesive) yield surface. Comparisons of simulations with experiments are presented. In the cases examined so far, the velocity grows very quickly to a peak and then slows, first with a deceleration greater than one “g,” which then transitions to an approximately one “g” deceleration. An analysis of air drag on the plates has shown that its effect is negligible in the time span of interest. In all cases in which the BUB2D code can be applied, the computations compare favorably with the results of the data analysis. This suggests that the code and model used in the computation are properly capturing the physics of the interaction between the soil and a non-deforming plate.

Jan 1, 2007

By D. S. Burgess

A commercially available Halon 1301 extinguisher has been evaluated as part of an explosion-suppression system for use in coal mines. Studies were made both of the dispersion pattern of the Halon 1301 at an initial pressure of 280 psig, and of the efficacy of this suppressant against 9.5 percent methane-air flames. These flames were quenched successfully only when the suppressant was applied before the fireball diameter exceeded 18 inches.

Jan 1, 1971

By Khosrow Ebrahimi

We document the occurrence, mineralogy and firing properties of magnesite from hydrothermal deposits in the upper Cretaceous ophiolites of Eastern Iran. These deposits occur as thin veins of nearly pure cryptocrystalline magnesite with only trace amounts of quartz, calcite, and dolomite. Ratios of CaO/SiO2 in the bulk ore are variable. The composition of dead-burned magnesite from these deposits, calcined at different temperatures and durations, is predictable from phase equilibria. Textures of the calcined magnesite were studied by SEM; results show that the principal impurites produced during calcination are forsterite, monticellite, merwinite, dicalcium and tricalcium silicates, and that these are located principally at triple junctions of the periclase crystals. The size of periclase crystals increased with temperature and duration of calcination and the amount of periclase-periclase grain contacts was reduced by increasing the concentration of impurities in the starting products. EPMA show: 1) that CaO and FeO contents in periclase increase steadily with an increase in the CaO/SiO2 ratio and the FeO content of the bulk ore, respectively, and 2) that limited solid solution exists between impurites. This study demonstrates that high quality dead-burned magnesia refractories can be produced from the Iranian magnesite with low CaO, SiO2 and FeO contents.

May 1, 2004

Objective To develop safety training tools for mine safety and health trainers that can be used for both new-miner training and annual refresher training. Background For the past 3 years, NIOSH has been developing training materials for mine safety trainers in response to gaps identified during stakeholder meetings. Most materials have been directed to the hazards of underground mines, but the recent passage of Part 46 of CFR 30 required new-miner and annual refresher training in aggregate operations. One result was the identification of another audience needing basic information about safety in mining. Trainers characterized trainees in this segment of the industry primarily as young males, many of whom had little work experience. Approach Training specialists from the Arizona State Mine Inspector’s Office approached NIOSH researchers early in2002 about the possibility of a collaborative project to develop safety training materials for new trainees in aggregate operations. A preliminary search of MSHA accident statistics identified over a dozen common hazards that could be targeted in a training video. A storyline was developed for review by safety specialists in the aggregate industry, and a script was written to cover the selected hazards. Although the target audience was primarily new hires, the finished video was also to be relevant to more experienced workers.

Jan 1, 2003

By Roxana Barrantes Huamán

El presente texto describe la geología económica del depósito aurífero Alpacay ubicado en Arequipa, Perú. El depósito Alpacay es un típico depósito mesotermal, filoniano que es explotado por la Cía Minera Yanaquihua, donde el mineral es procesado en una planta de cianuración, gravimetría y flotación. Costa. Asímismo, se realiza en la Franja Aurífera Nazca-Ocoña que alberga innumerables minas y depósitos en vetas angostas como Arirahua, San Juan de Chorunga, Chalhuane, Las Clavelinas, María Eugenia, entre otros. La alteración es básicamente argílica en la vecindad de las vetas y propilítica hacia el exterior.

Sep 12, 2011

By Matthew E. Meyer

Renovation, rehabilitation, restoration and expansion of existing residential, retail, commercial, hospital facilities and historic structures requires assessment and evaluation of foundation systems of various ages. The concept of demolition and reconstruction in urban areas is often more challenging, costly, and even prohibitive in some cases due to historic regulations. The authors have been involved with numerous projects related to existing foundation assessment and retrofit, including: hotel and hospital expansions, historic Art-Deco hotel renovations and expansions, garage structure expansions, additions to prominent auction houses, casinos, printing facilities; high-rise structure foundation retrofitting; forensic evaluations of existing building and highway structure foundation systems, and marine bulkhead sheeting systems. The use of non-destructive testing techniques, high-strain dynamic load testing, full scale pile cap load testing and 3-D laser scanning technology has proved to be vital in the assessment and evaluation process, as well as design of foundation retrofit alternatives. This paper presents various methods and techniques to facilitate a phased approach for optimization of existing foundations and subsequent re-use of foundation systems. These methods and techniques are illustrated through the author?s experience and selected case histories from projects with varied foundation and geologic conditions.

Jan 1, 2011

By Richard Campbell

Effective strata control, utilising fully encapsulated resin grouted roof bolts is dependent on the installed quality of the reinforcement elements. Resin based grouts are the main form of rock bolt anchorage in the underground coal industry in Australia and New Zealand. To be effective the system requires the mixing of the catalyst and mastic components of the resin as well as shredding of the cartridge that contains the resin. Over the past six years Solid Energy New Zealand Ltd (SENZ) has pioneered an extensive work programme quantifying the effects and extent of poor installation quality due to gloving, poor mixing and loss of encapsulation (Pastars 2003, Campbell et al 2003, Mould et al 2004, Campbell et al 2005 and Pastars & MacGregor, 2005). The One-Step Bolt (OSB), an innovative bolting solution designed and manufactured by Hilti Pty Ltd offers a self drilling, single pass bolting method that eliminates gloving, guarantees mixing quality and encapsulation performance of the installed product while not jeopardising the mechanical performance of the bolt. This paper details recent work undertaken by SENZ designed to understand and quantify the system performance of the Hilti OSB in New Zealand?s thick coal seam mining environments.

Jan 1, 2006

OWING to the gradual depletion of the hitherto plentiful supply of firewood in the immediate vieinity of Queenstown and Gormanston, which caused a steady increase in the cost of fuel for domestic purposes, the Mount Lyell Company took steps several years ago to make available as a substitute electric current from its Lake Margaret hydro-electric supply. In order to make this practicable it was necessary that the cost of electric power for heating purposes should compare favourably with the cost, of fuel, and the installation of domestic appliances brought within reach of the average householder, and efforts have been continuously directed towards this end since the year 1928.WATER HEATERSThe installation of electrical apparatus in local dwellings began with hot-water services, the heating elements being the types then procurable on the market and adapted to meet requirements.These, however, did not prove satisfactory, but the study of their bilure resulted in a type being developed locally which has overcome all difficulties. The first type of water heater evolved was an outside circulation one the element of which consisted of an iron pipe through which the water passed, insulated with micanite and wound with nichrome wire, the latter being covered with alundun cement to keep it in position and prevent oxidation. This was insulated on its outside surface with a layer of asbestos flour, and connected to the hot-water container as shown in Fig. 1. It was found, however, that the iron pipe had a short life, due to a certain amount of acidity in the water, and a copper pipe was substituted which proved very durable. Some heaters with this improved type of element are still operating after six years of use. The resistance wire is run at a very low current density, which ensures durability.

Jan 1, 1927

By P N. Holtham

As part of a long-term study of titanium minerals processing being undertaken by the Julius Kruttschnitt Mineral Research Centre (JKMRC), techniques have been developed to measure the electrical properties of the various minerals. The measured values will be used to model the behaviour of the various minerals in high-tension roll and electrostatic plate separators. The resistivities of ilmenite, rutile and zircon from a number of Australian producers have been measured by applying a DC voltage across a test sample and measuring the resulting very small current flow. By appropriate design of the measurement cell and attention to the experimental procedure, reproducible resistivity values have been obtained, ranging from 106Ωm for ilmenite to 1013Ωm for zircon. However, the conditions of measurement are radically different from those under which electrical separation takes place. It is not certain that the measured values reflect the resistivities seen under high-tension separation, during which the particles are subject to a high intensity corona field. Consequently, an alternative technique for measurement of resistivity under conditions of corona bombardment has been developed. It is based on the experimental procedure of Castle and Yelle (1979) used to measure the resistivity of fly ash under the conditions occurring in electrostatic precipitators. This paper describes the development of the segmented ground plane measurement surface and a high-voltage switched resistor network which comprises the in situ resistivity apparatus. Results are presented comparing the measurements made under corona bombardment with those made using the DC measurement cell. The equipment has also been used to study the current distribution from a corona wire, as a function of high-tension voltage and wire-to-plane spacing.

Jan 1, 2001

By S. Suzuki, Y. Maeda, N. Wakamatsu

"A new pyrometallugical technology, named KLS process, has been developed by Dowa Mining at its Kosaka Smelter to smelt various kinds of lead raw materials.The process consists of clearly separated two reaction steps, smelting and reduction. For this purpose, respective stationary furnaces are installed which are connected by a slag launder.Dry raw materials, together with pulverized coal and oxygen-enriched air, are injected through a lance pipe into the molten slag in the first furnace. It is kept under a high oxygen potential to remove sulfur completely. Resultant PbO rich slag overflows to the second furnace where pulverized coal and insufficient air are also injected through a lance pipe to reduce PbO to lead bullion and to compensate for thermal deficit. The entire operation is carried out continuously. The process development started back in 1981. In late 1986, a pilot plant with a capacity of 3.5t/H was constructed.Already nearly 20,000 tons of raw materials, mostly lead sulfate mixtures have been smelted successfully.IntroductionFor a long time, main raw materials for lead smelting at Kosaka smelter have been such secondary incombustibles as lead sulfate and lead-barium sulfate. The former is leach residue of the copper smelter flue dust and the latter originates from Iijima zinc refinery. While the most of lead concentrates produced locally has been smelted by an ISF of Hachinohe smelter in which Dowa Mining has a share.The surplus lead concentrates were processed at Kosaka by a hydrometallurgical method to convert PbS to PbSO 4 as pretreatment, and followed by simultaneous smelting together with the above secondary materials (1). Approximate output has been 1,5000 /M of lead bullion and slightly more than 2,000t/M of refined lead by adding lead bullion returned back from Hachinohe smelter (2)."

Jan 1, 1988

By A. J. MOORE

When the writer first saw the square-set timbering, he was at once impressed with the fact that the frames made by the sets, along the lode and across it, were composed of panels with rectangular openings, and it was puzzling to understand howsuch a collapsible construction could resist pressure that came unevenly on it. Later he learnt that the sets did not satisfactorily resist such pressure, but mullock filling had, to a great extent, to undertake this duty for them. So it appeared that the setswere practically an expensive scaffolding, enabling the miners to work in the face and carry the stope forward, till the filling was put in behind them to take the pressure of the roof and sides of the excavation. Of course some of the pressure is takenby the sets, but this is because "the set timbers prevent the filling being done perfectly; if it were practicable to remove the sets before filling, the filling by itself would more effectively support the back and wall, than do the combined sets andmullock. On the whole, therefore, the sets can hardly be said to be of much benefit where pressure has to be resisted. Despite this, the system has been of immense service in mining wide lodes, but for all that, it can only be pronounced a makeshift.This is no reflection on Deidesheimer, the famous originator of the square set, for, as will be shown later on, this way of...

Jan 1, 1912

By Nico Sutmoller, Rich Palladino

Underground voids present a unique geotechnical engineering challenge. This paper will address materials and transportation mediums that are typically used for backfilling underground voids with native material. After reviewing traditional backfill and transportation methods, this paper will explore the advancing technology of foam transportation and the advantages of using this technology for transporting fill materials into underground voids to backfill them with Liquid-Sand. The paper will also review the benefits that Liquid-Sand brings to these applications and highlight specific case studies in which foam transportation has proven effective and provided cost-effective, environmental benefits.

Feb 1, 2025

By Paul Zinner

An exhaustive program of geologic studies and mapping has been conducted by the Geological Survey in the Iron River district of Michigan since May 1943. Means of contributing to the success of these studies were sought by the Bureau of Mines, and eventually a program involving geophysical studies and core-drilling was undertaken in the area. All of the work was done either to develop data that would contribute directly to geologic studies or to investigate geophysical methods that might be used as a primary means for the discovery of minable iron ore.

Jan 1, 1949

By R. H. Dickson

This paper, which describes the milling practice of the Verde Central Mines, Inc., is one of a series on milling methods and costs being prepared by the United States Bureau of Mines. GENERAL DESCRIPTION The Verde Central concentrator is located in Walnut Gulch, about 1 mile west of Jerome, Ariz., and on the Jerome-Prescott highway. It is about 1,000 feet distant from the main shaft of the Verde Central mine and treats ore from this mine only. The mill is connected with the main shaft of the mine by a 24-inch gave railway, over which the ore is hauled in 5-cubic yard capacity, rocker, side-dump cars, by a 3-ton Brookville gasoline locomotive.

Jan 1, 1931

By Peter Altounyan

The rate of decay of the energy from a hammer blow to a coal mine roof is related to the size and nature of the contacts between the rock being struck and its surroundings The use of this principle as a basis for testing roof condition in South African coal mines has been investigated under a SIMRAC funded project, with the objective of reducing the number of roof falls. ( I ) A prototype instrument having a simple numeric display related to the energy decay rate (the Acoustic Energy Meter) was constructed and used to carry out surveys at mines covering the range of coal mine roof geology and condition. The equipment was simple to use and provided excellent discrimination between visually intact roof and less stable conditions, once the normal/abnormal threshold had been established for a given site. Areas of potential roof failure were identified close to roof slips and igneous dykes, and confirmed in areas of visible deterioration. Directional stress effects on roof condition were also identified at some sites, with consistent differences in readings obtained depending on the direction of drivage. Repeat surveys also indicated areas where roof conditions were deteriorating with time. Based on the success of the prototype, a hand held version of the instrument. has been developed to a specification from Anglo Coal. This incorporates a simple 'traffic light' green / amber/ red display, making the device suitable for routine use by mine operatives This version is now undergoing trials at an Anglo Coal mine. It is concluded that the Acoustic Energy Meter shows great potential as a test instrument providing output which relates to the stability of the immediate roof.

Jan 1, 2000

By Dave Bigby

Hatworth Colliery, operated by RJB Mining (UK) Ltd, is successfully mining the Deep Soft Seam at a depth of 1000m using single face retreat longwalling. The seam is characterised by a weak roof generally comprising 4 to 6m of well bedded carbonaceous mudstones overlain by weak siltstones. The paper describes the layout and support design strategies which have enabled the colliery to adopt sole support by rock reinforcement techniques for its longwall gateroads. To achieve this success the colliery layout has had to be radically modified to take account of the in-situ horizontal stress field. The layout is also closely controlled by environmental considerations, the seam being one of the gassiest in the UK Economic support by strata reinforcement has been achieved using a combination of rockbolting of the roof and sides installed at the face of the heading, and systematic double birdcage cable bolting installed on drivage and supplemented ahead of the retreating panel. The layout and support strategies have been developed through a combination of detailed underground measurement of support and stress parameters backed up by numerical modelling using FLAC. The FLAC modelling has paid particular attention to careful representation of bedding properties and validation through underground stress measurement.

Jan 1, 1996

Steady increases in longwall production have required operators to apply greater quantities of ventilating air in an effort to control and dilute respirable dust. Significant increases in shearer speeds necessitate that longwall supports also be advanced at a faster rate. Both of these factors may contribute to overall respirable dust levels on the longwall face because as supports are lowered and advanced, broken material falling from the top of the canopy is entrained directly into the air stream. To address this issue, the Pittsburgh Research Laboratory collected respirable dust samples from four longwall faces to characterize shield-generated dust. This paper investigates the influence of air velocity and shield advance rates on respirable dust levels. Also discussed are engineering controls currently used to reduce shield dust and alternative controls being investigated by the National Institute for Occupational Safety and Health (NIOSH).

Jan 1, 2009

By Shamsher Prakash

Equivalent spring constants for analysis of footings is a function of Young's modulus of pile material (Ep), shear modulus of soil (Gs), and geometry of the footing and/or piles. Shear modulus is strongly strain dependent in soils. Therefore, the spring constants are strain dependent, which is acceptable to the Geotechnical engineers. However, structural engineers prefer to use spring constants as a function of displacement, rather than strain. In order to develop these relationships, appropriate relationships between strain and displacement are needed. Also, modulus degradation with strain needs be built into these relationships. Description of spring constants kx , ky, and kz in x, y, and z direction and k?, k?, k?, about x, y, and z directions are relatively simple. However, description of kxø and ky?, the cross-coupling spring constants depend on 2 - components of displacement and rotation. Thus, there are 8 spring constants and likewise there are 8 damping constants. Approximate strain-displacement relationships on which displacement dependant k's and c's are based are presented with appropriate equations, and a numerical example is included illustrating k's and c's as functions of displacement.

Jan 1, 2002

By P. W. Billwiller

Abstract The Britannia Mining and Smelting Company, Limited, have replaced diamond drills with percussion drills and tungsten: carbide bits for most of their blast hole drilling operations and have thereby reduced ore breaking costs. Two-inch Carset bits .are used, with one-inch hexagonal Atlas Chippewa alloy steel in 3-foot .and 6-foot lengths. Locally made couplings of Atlas SPS 245 alloy steel connect the rods. The machines used are 31½-inch automatic leyners with lugged or anvil block chucks. For drilling holes below the horizontal, the lugged machines with special adapter rods made from 114- inch solid round Atlas SPS 245 are required. These rods are lugged at one end and a water hole is drilled for six inches into the other end. Over this rod is placed a water swivel which permits the water or air to be sent directly into the steel. A decreased cost per foot, increased footage per shift, and the use of standard equipment and crews are some of the main advantages of tungsten carbide drilling over diamond drilling. Introduction Long-hole drilling with percussion drills and sectional steel was introduced in several American mines some twenty-five years ago. It did not prove very successful, however, because the rapid gauge loss in steel bits necessitated the use of very large starter bits. This in turn rapidly fatigued the straight carbon-steel then in use, made it difficult to maintain the couplings, and resulted in a slow drilling rate. The introduction of the tungsten carbide insert bit and alloy drill still has changed this picture and opened real possibilities for the application of percussion drills to blast-hole drilling. If this type of bit had been perfected ten years ago, much of the research work and experimenting done to apply diamond drills to ore breaking would have gone toward developing the application of the tungsten carbide bit to this problem.

Jan 1, 1950