Search Documents

By J. -G. Swanson

Dust control in longwall coal mining depends primarily on the prevention of dust at the source and secondarily on the suppression of airborne dust. One of the primary methods for the prevention of dust is the wetting of the coal face prior to extraction, which can be achieved with water spray systems installed on the shield supports. The spray droplets must travel across the airway to the longwall face, where high ventilation air speeds can entrain water droplets and prevent them from reaching the face thus minimizing the dust control at the source. Through an evaluation of spray plume characteristics in a wind tunnel, the droplet size and droplet drift behavior was determined. This drift behavior was examined by evaluating the spray plume concentration drop and the droplet size shift near the nozzle exit at varying air speeds. Based on these evaluations, CFD modeling was applied to simulate the spray behavior for varying geometries. These results led to the selection of appropriate spray nozzles capable of carrying water droplets to the face at higher air speeds, resulting in an adequate wetting of the coal face and reduced dust generation.

Jan 1, 2012

By Fred Breu, Ronald E. Heuer

INTRODUCTION The Point Lepreau nuclear generating station was constructed in the late 1970's and early 1980's by the New Brunswick Electric Power Commission. Point Lepreau is a small peninsula on the north shore of the Bay of Fundy, about 55 km west of St. John, New Brunswick. Cooling water for the plant was to be obtained from and discharged into the Bay of Fundy by the system of shafts and tunnels illustrated in Fig. 1. The design engineer for the cooling water system was Albery, Pullerits, Dickson and Associates, Ltd., Toronto. Ferrera-Resco Ltd, Windsor, Ontario, was contractor for construction of the cooling water shaft and tunnel system, which was done between 1976 and 1979. The senior author was project manager for Ferrera-Resco, the junior author served as consultant to Ferrera-Resco on evaluation of certain geotechnical questions which arose during construction. SITE CONDITIONS Geology Except for limited overburden soils at the onshore shaft sites, the tunnels and shafts were constructed entirely in Triassic conglomerate, sandstone, and siltstone, with some shale interbeds. The bedding strike averaged about N6°E, The dip was to the west at about 30° along the Discharge Tunnel and 40° along the Intake Tunnel. Rock along the Intake Tunnel was mostly sandstone and siltstone and more thinly bedded, with RQ D generally in the range of 50 to 60%. Rock along the Discharge Tunnel tended to be coarser sandstone and conglomerate and more thickly bedded, with higher RQ D averaging about 80%. In addition to bedding joints, two other joint systems were identified

Jan 1, 1985

By Robert G. Lundquist

This report summarizes all relevant findings and conclusions regarding capabillty of high-energy projectile impact to operate effectively in an open pit mining environment and to successfully handle secondary breakage and bench scaling problems. A silenced, aimable, mobile projectile launcher was designed and fabricated, utilizing a Government-furnished smooth-bore, 90 mm cannon. The silenced launcher was tested at the contractor's test site prior to shipment to ANAMAX Mining Company's Twin Buttes Mine near Tucson, Arizona. Demonstration tests were conducted at an inactive waste dump in the mine on 39 oversize boulders to determine the relationship between boulder size and projectile energy required for secondary breakage. The high energy projectile impact method (known by the acronym REAM -Rapid Excavation and Mining) was tested on an additional 23 boulders in the working mine and on 31 areas of potentially loose rock high on the pit walls. Most of the secondary breakage tests were successful and acceptable for open-pit mining purposes without producing large amounts of fly rock. Five of the 31 scaling tests were successful with one shot, but most of the remainder required two or more shots, and a few could not be dislodged because they were not as loose as they appeared to be, based on visual examination from a distance. Cost comparisons between the REAM method and conventional methods of secondary breakage and bench scaling are discussed. A film documentary, REAM--Mining Applications of High Energy Projectile Impact, has been produced by the contractor depicting the applications of the silenced cannon.

Jan 1, 1976

By J. R. Knudson

A major contribution to the art of blasting was made at the Cleveland- Cliffs Iron Company?s Hawkins Mine in Cashwauk, Minnesota during April of 1956. It was here that the first experiments with fertilizer grade ammonium nitrate were conducted-experiments which led to the development of the ammonium nitrate and fuel oil method of blasting which has been eagerly adopted by open pit and quarry operators throughout the United States. While this new blasting agent was a more or less natural outgrowth of the Akremite Process devised by Maumee Colleries of Terre Haute, Indiana; no one, to our knowledge, had used this particular combination of ingredients prior to this time. Certainly this was a "break-through" as far as the Lake Superior District was concerned. Akremite consists of a mechanical mixture of grained ammonium nitrate and a solid carbonaceous material packed in a plastic bag. At the time of its introduction to the Mesaba Range, Akremite sold for 10.5 cents a pound as compared to the 18 cent powder previously used in both wet and dry large hole blasting. The discovery of this agent was indeed a remarkable achievement, one that afforded a substantial reduction in blasting costs. However, Akremite proved to be only an intermediate step in the evolution of our present low cost explosives. Cleveland-Cliffs utilized prilled ammonium nitrate and fuel oil and then eliminated the mixing and packaging plant entirely by combining the two raw materials in the field at the drill hole collar or in the hole itself. Thus we have approached the ultimate in simplicity, for the blaster and his helper now manufacture their own explosives not only as they are needed but where they are needed, and at a cost of under 4 cents a pound. This two-man crew may charge and explode as much as 8 tons of ammonium nitrate in an eight-hour shift and in so doing break some 65,000 tons of ore.

Jan 1, 1959

By J. DuCarme, A. Smith, M. Reyes

"A magnetic proximity detection system is mounted on a mobile mining machine to prevent underground workers from being pinned or struck by machine motion. The system generates magnetic fields around the machine to determine safe working distances. The minerworn component measures the magnetic field in order to approximate location. Large masses of steel, such as those from mining equipment, can alter the magnetic field distribution. This affects the locational accuracy of the system, thus adversely impacting worker safety. To examine this problem, U.S. National Institute for Occupational Safety and Health researchers developed a method and test system to study the influence of a steel mass on the magnetic field distribution. The results show that a steel plate can strengthen the magnetic field perpendicular to the generator by up to 40 percent. Furthermore, they show that the degree of the influence on the field distribution is a function of distance. The results from this study can be used to further develop and improve the performance and reliability of electromagnetic proximity detection systems used in underground mining applications.IntroductionOn average, 250 miners are injured every year, and 43 miners were reported to be killed by striking or pinning accidents involving continuous mining machines in the United States between 1984 and 2015, according to the U.S. Mine Safety and Health Administration (MSHA, 2015). Continuous mining machines are large mobile machines used to mechanically cut coal in underground mines. These machines weigh approximately 60 t (132,000 lb) each. Although modern continuous mining machines can be remotely controlled, operators still need to be close to the machine primarily because of the low visibility and wide blind spots of the underground working environment.The MSHA promulgated a final regulation in 2015 that requires the use of proximity detection systems on all continuous mining machines except fullface machines. MSHA has approved five such systems to be intrinsically safe for use in underground coal mines: (1) Strata Worldwide’s HazardAvert System, (2) Frederick Mining’s Model 200 HazardAvert Detection System, (3) Nautilus International’s Coal-Buddy System, (4) Matrix Design Group’s M3- 1000/Joy Global SmartZone Gen 1 and (5) Matrix Design Group’s IntelliZone/ Joy Global SmartZone Gen 2."

Jan 6, 2018

By M. M. Kim

Zn-27% Al was pressure infiltrated into a column of 20 micron diameter abrasive grade SiC particles to give billets with particle loading of 50 voli.une %. Some billets were heated to a temperature where they became semi-solid and diluted with liquid Zn-27% Al alloy to give billets with particle loadings of 12 and 16 volume %. Some of these billets were then extruded into wire with an area reduction of approximately 98%. Tensile properties of the as-cast billets were always inferior to those of the matrix alloys; however, the extruded composite samples showed at 37% improvement in ultimate tensile strength compared to their extruded conventional counterparts. The fracture surfaces of these samples are described.

Jan 1, 1990

By Erwin L. Zodrow

"This paper is based on a statistical analysis of the Smallwood iron ore mine (6). In this mine, the prediction of magnetite is especially difficult because of strong trends. Recognizing the statistical limitations of the sample data, the paper approaches the basic statistical analysis of the magnetite by endeavouring to obtain a first approximation of its sample density function. The knowledge of the distribution of a random variable is essential for several reasons, but particularly: (1) to obtain reliable estimators of the population parameters -for example, mean and variance; and (2) to use these estimators in hypothesis-testing concerning future experiments -sample points and sample intervals."

Jan 1, 1968

By P. Rosario

The application of high pressure grinding rolls (HPGR) has been growing in the mining industry for the last 10 to 15 years. The major benefits supporting this trend are better energy efficiency, improved grinding capacity, and higher metal recovery in downstream processes such as heap leaching and flotation. In general there is limited quantitative knowledge on the true benefits of HPGRs relative to SAG mills in comminution, and about which situations one deals with better than the other. This paper will present a structure for comparison of the energy requirements for HPGR versus SAG mill considering complete circuits for comminution of precious and base metals hard ores. The work presented is from the design of four complete circuits based on ore data from two sites.

Jan 1, 2010

By M Thierry Bernart

The software QUALITIR is a software developed by CNSIDCI, framework on five research and experimentation years. This conceived tool by specialists for professionals is a decision aided design tool concerning mining. It makes party the rare software regrouping the different themes approached by the profession namely, the general idea of blast design, blasting sequences, the fragmentation as well as the study of vibrations. Henceforth it is by the intermediary of such tools that performances in term of profitability, security or impact on the environment will be able to be realized.

Jan 1, 1997

By Marco Lombard, Paulus Kapolo, Christopher J. Greet

"The conversion of a concentrator from one grinding media type to another is a major undertaking in terms of both financial and technical risk. So, a strategy of completing sufficient laboratory and field tests to mitigate this risk, and give the operation confidence that advancing to plant trial will give a high probability for success.The objectives of this paper are twofold: to provide the reader with a strategy for mitigating risk prior to undertaking a plant trial; and to provide a statistical basis for analysing plant trial data. That is, when employing an electrochemically inert grinding media in the primary grinding circuit it is possible to change the pulp chemistry of the system and improve the metallurgical response of the ore.This paper tracks the changes in pulp chemistry and metallurgical performance of Rosh Pinah Zinc Corporation’s silver/lead/zinc concentrator as the primary ball mill was converted from forged steel grinding media to high chrome grinding media. The changed in metallurgical performance are correlated to the shift in pulp chemistry.INTRODUCTIONTheoryBruckard et al (2011) recently published an article describe the effect of the grinding environment on the flotation of copper sulphides. While this paper confined its discussion to copper sulphides the arguments presented apply equally to other sulphide mineral systems. Broadly, these studies indicate that most sulphide minerals are more noble than the grinding media used during comminution. Therefore, the sulphide minerals are cathodic with respect to the forged steel grinding media, and the following reactions apply:Cathode (sulphide mineral): ½O2 + H2O + 2e- ? 2OH- (1)Anode (grinding media): Fe ? Fe2+ + 2e- (2)A galvanic couple between the grinding media and the sulphide mineral(s) exists, which increases the corrosion rate of the forged steel media. The corrosion products of the grinding media, iron oxy-hydroxide species, invariably precipitate on to the surfaces of the sulphide minerals thereby affecting their floatability (Johnson, 2002).The application of more electrochemically inert grinding media to “real” ore systems at an industrial level to improve metallurgical performance has not gained universal acceptance. The aim of this paper is to provide a protocol for conducting laboratory and plant test work that clearly demonstrate that metallurgical benefits are not only possible, but measureable, by way of example. In this case, the work conducted at Rosh Pinah Zinc Corporation in Namibia is described."

Jan 1, 2013

Geophysical anomalies result from the passage of hydrothermal fluids through rocks. Interpretation of these anomalies, when integrated with available geological and geochemical data, assists the construction of a conceptual model of the original hydrology of the system. The original extent of a geothermal system is often indicated by the distribution of low resistivity argillic clay alteration. Quartz-adularia vein deposits, silica sinters or stockwork (often mineralised) cause local increases in resistivity. Appropriately chosen electrical techniques can therefore be used to help target such structures. Airborne magnetic surveys have also proven useful in New Zealand epithermal exploration, because hydrothermal fluids destroy magnetite causing extensive demagnetisation anomalies. Ground magnetic surveys can sometimes be useful for geological interpretation on a local scale. Positive gravity anomalies may occur as a result of mineral precipitation (silica or calcite) in high porosity host rocks, while negative gravity anomalies can result from hydrothermal fracturing and leaching of relatively dense host rocks. The relative merits of these geophysical techniques as used in the exploration of epithermal mineral prospects are discussed, with particular reference to the Hauraki Goldfield. The preferred method for defining zones of quartz veining/silicification is vector or tensor gradient resistivity. Exploration strategies and technique refinements are suggested as a means of improving the resolution of potentially mineralised target structures, in a more efficient and cost effective manner.

Jan 1, 1993

By T. A. Grammatikopoulos, B. Vasily, A. H. Clark

"The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoeshaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York, no carbonate protolith is preserved, and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560°C, or, alternatively, 550 MPa and ca. 630°C.Several high-grade zones, averaging >40% but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 cm to 5 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates.St. Lawrence compares favourably to other known prospects and operating wollastonite deposits: having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production."

Jan 1, 2003

By Juan Oswaldo Alfaro, Angel C. Nuñez, Hildebrando A. Cóndor

Se ha desarrollado un software para facilitar la evaluación del proceso molienda-clasificación en plantas concentradoras. Se ha modelado en UML-Lenguaje Unificado de Modelado; los datos e información se almacenó en SQL Server; se programó en Java (Programación Orientada a Objetos). Investigación Aplicada y Cuantitativa obteniendo como resultados un Software para Circuito de Molienda-Clasificación (Directa e Integral).

Sep 1, 2017

By D. E. Sherwood

Recent developments in high torque hydraulic rotary rigs has lead to the construction of secant bored pile walls by rotary drilling methods in circumstances where earlier methods were difficult and in some cases impossible. The evolution of secant bored pile wall construction is described including classical, rotary drilled and continuous flight auger construction methods. The paper then details the restraints which have been created in recent inner city redevelopment, many of which were not relevant in the early days of the technique. Typical examples of walls are presented to show the adapatability and advantages of the secant bored pile wall method. A number of in-situ retaining wall construction techniques are then compared in detail with regard to relative cost, technical quality and practicality.

Jan 1, 1989

By T. G. Carter, R. I. Miller

First, the influence of variation in the

Apr 1, 1995

By Walter E. Montgomery

ACCIDENT-PREVENTION work in years gone by has been carried on by many mine managers as a philanthropic movement, but in recent years they have come to realise that Safety is good business and pays tangible dividends. Let us begin with the word itself. We are told that an accident is "any-thing occurring unexpectedly, undesignedly, or without known or assign-able cause&apos;. It is further explained that it is any &apos;unpleasant or unfortunate occurrence involving injury, loss, suffering, or death", and, finally, "any unintentional or non-essential circumstance". We admit that accidents are unfortunate, unpleasant, unintentional, and they generally happen undesignedly and to a great degree unexpectedly, but to say that they happen "without known or assignable cause" leads us to believe that the word &apos;accident&apos; is often misused. Would it not be more correct to say that a man suffered a "personal injury"? The word &apos;accident&apos; in its proper sense implies something over which no one has any control, but when the majority of all so-called accidents are analysed we arrive at the incontestible fact that some act or action, previous or present, was the underlying cause. As long ago as the year 1556 this fact was mentioned by Georgius Agricola, who, in writing a paper on metallurgy, aptly stated, "It remains for me to speak on the ailments and accidents of mines, and of the methods by which they can guard against these, for we should always devote more care to maintaining our health, that we may freely perform the functions of our body, than to making profits". Farther on, Agricola relates in more detail, "Sometimes workmen slipping from ladders into the shafts break their arms, legs, or necks, or fall into the sumps and are drowned; often, indeed, the negligence of the foreman is to blame, for it is his special work both to fix the ladder so firmly to the timbers that they cannot break away, and to cover so securely with planks the sumps at the bottom of the shafts, that the planks cannot be moved nor the men fall into the water; wherefore the foreman must carefully execute his own work. Moreover, he must not set the entrance of the shaft-house toward the north wind, lest in winter the ladders freeze with cold, for when this happens the man&apos;s hands become stiff and slipping with cold, and cannot perform their office of holding. The men, too, must be careful that, even if none of these things happen, they do not fall from their own carelessness&apos;.

Jan 1, 1938

By W. A. Gow, J. A. Vezina

"A new process for treating scheelite for the production of tungstic tri-oxide is described. The novelty of the process resides in that an ion-ex-changer is used to convert sodium tungstate to either ammonium tung-state or tungstic acid.The process consists of a conventional hydrochloric acid leach of the scheelite concentrate, and the dissolution of the impure tungstic acid thus produced with sodium hydroxide at pH 8. The sodium tungstate solution is clarified and passed through a column of Dowex 50Wx8 ion-ex-change resin to exchange the sodium ions for either hydrogen or ammonium ions, both being suitable. The tungsten-bearing column effluent is evaporated to crystallize the tungsten as ammonium tungstate; the crystals are washed with nitric acid and water and decomposed by heat to pro-duce tungstic trioxide of high purity.Ninety-six per cent of the tungsten in the concentrate may be re-covered as tungs tic trioxide (W03), and the reagents consumed are 0.7 g HCl, 0.41 g NaOH and either 1.73 g NH.Cl or 225 g HCl per gram of tungsten."

Jan 1, 1966

By James W. Derrick

General widespread interest in fine coal cleaning circuits did not occur in the United States until the mid 1960&apos;s. Up until this period the relatively low price for which bituminous coal was sold did not justify for many operators the capital and maintenance costs associated with the beneficiation and drying of fine coal. However, with current growing interest in this area, the introduction of new types of process equipment along with modifications to existing components is occuring to maximize the recovery of coal fines. In 1973 Derrick Manufacturing Corporation introduced high frequency screening machinery into the coal industry. The first design consisted of a 4 ft. wide 18 ft. long single deck screen frame with three 100 mesh woven wire screen surfaces divided by repulping troughs for the addition of wash water. In addition, a special slotted rubber dewatering deck was installed on the discharge end of the unit to assure adequate dewatering of the screen oversize. This panel had nominal 25 mesh X 3.0" slotted openings. The machine was also equipped with a special high speed-low amplitude (3600 RPM .032" % AMP.) integral vibrator.

Jan 1, 1983

By H. E. Cross

In a minerals-recovery context, the object of exercising control over milling operations must be threefold, 1) To achieve maximum recovery at 2) minimum operating costs and 3) making maximum use of installed equipment, Milling is one of a sequence of operations which have as their objective the economic recovery of minerals from mined ores, All operations in the sequence are interdependent and each is both influenced by and itself affects all other unit processes. The part which grinding plays in achieving each of the above objectives is indicated in the following analysis: In South Africa, the most important mining operations are still the gold mines, A vast reservoir of knowledge and experience in treating the Witwatersrand and associated ores has been accumulated. and recoveries are consistently high, However residue values do vary and frequently this is due to fluctuations in the degree of grind, The significance of changes in residue values is indicated by the following example: On a modern mine, the residue values varied from 0,25 to 0,33 dwi; per 2000 lb, during a period of 6 months, The cash value of the gold thus lost varied therefore between $0.44 and $0.58 per 2000 lb, ton. A residue which assays 0.30 dwt per ton would contain approximately 0.26 dwt as undissolved gold and 0,040 dwt per ton as dissolved gold present in residual solution after filtration. This dissolved gold loss is a function of efficiency of filtration and varies from 0.030 to 0,.070 dwt per ton of residue.

Jan 1, 1970

Jan 1, 1967