Search Documents

By R. C. Woodhead

During past years the most difficult problem presented to the coal preparation engineer has been the cleaning of fine coal, The problem of handling fine coals is more involved than the coarser sizes, because the higher surface moisture contents complicate screening, and the larger percentages of fine near size material complicate separating problems. Low gravity high capacity specific gravity separations were not possible with equipment available at that time. Coal preparation engineers did develop machines that would effect a separation of the fines, however, to maintain a high efficiency, the point of separation had to be a relatively easy one. The more difficult separations were made in the coarse coal sections of the washeries, and the fines were generally cleaned at higher specific gravities in equipment such as tables, feldspar jigs, rheolaveurs, etc. Clean products from both processes were mixed, resulting in overall lower ash contents, During the last several years, however, we have been confronted with increasing demands ZGP more precise separations of finer coals to still further reduce ash contents. A study was begun and a program instigated to improve the cleaning of fine coal, The result of this endeavor was the development of the new cycloidal heavy medium cyclone.

Jan 1, 1964

A Study of Extracting Vanadium from Stone Coal Using Cyclic Oxidation

Sep 13, 2010

By J. Wagner, P. Eger, G. Melchert

In 1991, LTV Steel Mining Company decided to close an open pit taconite mine in northeastern Minnesota, using a passive treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. Over 50 million metric tons of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages, and prior to closure annual median concentrations ranged from 1.5-50 mg/L. Copper, cobalt and zinc are also present but are generally less than 5% of the nickel values. Median pH ranges from 5.0 to 7.5, but most of the stockpile drainages have pH greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential a stockpile had to produce acid drainage, the lower the permeability of the capping material required. Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to over 90% for the plastic liner. Five constructed wetlands have been installed since 1992, and have removed 60-90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1% of those for an active treatment plant. Since mine drainage problems can continue for over a hundred years, the lower annual operating costs should pay for the construction of the wetland treatment systems within seven years.

Jan 1, 1999

By Deepu Philip, Pratik Agarwal, Ajay Kumar Shukla, Ishani Shukla, G Rajesh

Steel plants generally employ static BOF end point control models to arrive at a given temperature and chemistry at the end of blow. These end point models have now been supplemented with chaos control models to steer the blowing process in the right direction while the blow is in progress. Merely arriving at the correct end point temperature is however not adequate because in the subsequent stages as well the temperature variations can be large and unpredictable. The present paper deals with an integrated model to take into account the effect of all parameters affecting temperature and composition from tapping to the start of casting to minimize the use of LF or aluminum heating, and also minimize grade mixing. The application of lean operations strategy is explained in which the previous “Push System’ is changed to a “Pull System”, minimizing the use of ladle furnace or aluminum heating during steelmaking.

Jan 1, 2014

By J. D. Miller, R. J. Smith

Earl C. Herkenhoff Publication of the article "The Flotation Behavior of Digested Asphalt Ridge Tar Sands" by R.J. Smith and J.D. Miller has confirmed and again spotlighted a most significant and important development in the field of tar sand and heavy oil mining. This is the ability to recover 95 % of the bitumen in dry tar sands by a hot water process. The initial investigation by Miller and Sepulveda in early 1978, "Separation of Bitumen from Dry Tar Sands," was the first blockbuter. It is disappointing that there has been so little scientific and industry ackowledgement that the authors laid to rest the long entrenched belief that the sand grains had to be "water wetted" for a hot water process to be applicable. Dr. Miller and his researchers at the University of Utah used slightly different mineral dressing terminology in describing their process but it is essentially the old, established technique of high solids attrition scrubbing at elevated temperatures with a conditioner or modifier, followed by dilution and froth flotation. Similar techniques were described in detail for other nonmetallic minerals in the mid-1940s by Stuart Falconer of American Cyanamid Co. The authors used a 15-minute "scrub" period (or in their terminology "digester step") at 73% solids and 95°C (203°F) in a 0.3 m solution of sodium carbonate -about 4 kg/t (8 lb per st) of tar sand. Flotation was at 10% solids. Obviously, the scrub is an expensive step with respect to energy input but the high recovery of bitumen appears to justify it. Two basic questions then arise: • What are the effects of shorter scrubbing time, lower temperature, and less sodium carbonate? • Would a two-stage approach be advantageous? That is, could you get the major proportion of the bitumen with a mild scrub and apply the high power and temperature only to the refractory portion? These variables should be evaluated. Apparently, all results were only for rougher flotation. What would the grade and recovery of bitumen be if multiple cleaner flotation steps were employed? We must concede that a 60-62% grade of bitumen leaves considerable room for upgrading. Finally, it should be noted by all executives who approve funds for heavy oil recovery schemes, most of which are variations of in-situ methods, that mining can yield a 95% recovery of bitumen. That is correct, 95%. Imagine what that does to the total barrels recovered from a heavy oil resource compared with the scrawny 30-35% maximum recovery we are getting now. The conclusion-let's mine heavy oil and tar sands. Reply by R.J. Smith and J.D. Miller We, too, share Mr. Herkenhoff s enthusiasm for the mining of tar sands-heavy oil and continue the development of related processing technology. Specifically, it will be noted that by appropriate control of bitumen viscosity in the feed (probably the most important variable for successful separation) the recovery can be accomplished at low digestion temperature and low addition of alkali. A 91 t/d (100 stpd) pilot plant based on our technology is now being operated by Enercor in Salt Lake City (Hatfield, Oblad, and Miller, 1982). In these same pilot facilities, rougher concentrates containing more than 80% bitumen on a dry basis are being produced from Asphalt Ridge Feed. However, the processing of certain other tar sands results in incomplete digestion of bitumen/sand aggregates as discussed elsewhere (Miller and Misra, 1982). Such undigested aggregates are shown in Fig. 1. In this regard, it is intended that a recycle stream will be installed in the pilot plant to provide for redigestion of middling products. Further details regarding surface chemistry aspects of this tar sand technology have recently been published (Misra, Aguilar, and Miller, 1981). References Hatfield, K.E., Oblad, A.G., and Miller, J.D., 1982, "Pilot Plant Recovery of Bitumen from Oil Wet Tar Sands," Processing, Second International Conference on Heavy Crude and Tar Sands, Caracas, Venezuela, Feb. 7-17. Hatfield, K.E., Oblad, A.G., and Miller, J.D., 1982, "Pilot Plant Processing of Oil-Wet Tar Sands," Symposium, Rocky Mountain Fuel Society, Salt Lake City, Utah, Feb. 18-19. Miller, J.D. and Misra, M. 1982, "Hot Water Process Development for Utah Tar Sands," Fuel Processing Technology, Vol. 6, No. 1, April, pp. 27-49. Misra, M., Aguilar, R., and Miller, J.D., 1981, "Surface Chemistry Features in the Hot Water Processing of Utah Tar Sand, Proceedings, "Symposium of Separation Science and Technology for Energy Applications," Gatlinburg, Tennessee, May 5-8.

Jan 11, 1982

By D. Harrington

The placing of much, sometimes practically all, of the burden of the expense of mine accidents on the shoulders of the mine operator by compensation laws, and the fact that the problem of protecting the life end limb of workers is now by public opinion largely if not wholly passed to each industry to solve (and present-day thought strongly supports the justice of both of these propositions), are forcing industrial organizations into accident-prevention. Work. This policy is being adopted not alone to protect the companies; in addition, executives alert to their opportunities and obligations are taking part in this work personally to protect themselves. The functions of industrial executives in accident-prevention work are becoming numerous and complex. Executives who are logical in their reasoning, quickly see that before a company can constantly ask or expect the workers to heed safety suggestions, the company and its officials must "put their house in order" by laying down a concrete, definite safety program. For mines this includes primarily adoption of a to a logical mining method, the installation of safe miming equipment and practice the netting forth in definite form (preferably do a printed pamphlet) of the company's minimum safety requirements, and the organization of its operating officials into an accident-prevention body. After the company has its own affairs so arranged that it can go to its workers with "clear, hands" in promoting a safety program, the real work begins; and this is especially applicable in mining.

Jan 1, 1939

By Daniel Saint Don, Jacques Dumouchel

QIT Madagascar Minerals (QMM)’s heavy mineral sand deposit located near the Village of Fort Dauphin, Madagascar was recently drilled using Boart Longyear Company’s Mini-Sonic drill. Continuous sand core samples were obtained to a depth of up to 30 meters for analysis and compared with the existing drilling data. Results were used as part of a validation process of the resource estimate, based on approximately 1,500 exploration holes drilled to date.

Jan 1, 2005

The concept of the Unified Comminution Model (UCM) was presented at the 23rdIMPC. The model utilises computational techniques to calculate the mechanical environment in any comminution device, and then incorporates the outcomes from rock breakage tests to predict the product from a device. The model is fully mechanistic, and incorporates the capability to simulate novel equipment. This paper presents the progress on the first application of this concept to applied comminution equipment. This novel comminution model aims to integrate all comminution models within a single struc-ture. This will provide a step change in the predictive power of comminution models, and include a wide range of particle properties that will enable it to be linked to the upstream and downstream process of mining and recovery. Major advances over current models will be the capability to predict liberation, preferential grinding, performance of new and novel devices, and to have power as an integral driver of the comminution simulation process. The methodology and model structure have been developed. An equation within a population balance framework has been derived as the basis for the UCM. A set of SAG mill pilot has been used as the first test case. The breakage characteristics of the ore have been extensively tested utilising a new range of breakage tests required by the rigorous UCM structure. The mill was simulated with the EDEM - DEM software. A partial test simulation of the pilot SAG mill has been conducted. This serves to demonstrate the feasibility of this modelling technique, but still lacks important ore characterisation components that are under development. The study has raised a number of significant challenges to the accepted understanding of the comminution process. Through addressing these challenges considerable insight has been gained into the energy environment in mills and the requirements of breakage testing. The ore characterisation methods and energy transmission derived from DEM simulations remain as major research items.

Jan 1, 2014

By W. Smith

The U.S. Bureau of Mines (USBM) is using laboratory and computer-based techniques to investigate the post- failure behavior of yielding pillars and pillar reinforcement techniques to control entry deformation. Poorly dimensioned yield pillars, can cause adverse ground conditions. Laboratory studies to evaluate various reinforcement techniques for controlling yield pillar deformation were conducted. A cracking and crushing model is used to evaluate potential tensile and compressive failure planes within pillars of various widths to assess the degree of yielding and stress redistribution. The use of an elasto-plastic model to evaluate the effect of various reinforcement on yield pillars is also discussed. These procedures effectively account for the residual pillar strength, important in yield pillar design.

Jan 1, 1995

Two miners were fatally injured when a pillar bump occurred during retreat mining in a southern West Virginia coal mine. The mine was operating in the Eagle seam with overmining in the No. 2 Gas and Powellton seams. A coal bump is defined as a sudden and violent failure of coal caused by the release of stored strain energy in the pillar. While significant strides have been made by academia, industry, and regulatory agencies to better understand bump conditions and mitigation techniques, coal bumps represent a long standing, highly site-specific engineering problem in which the exact failure mechanism(s) is not clearly understood.

Jan 7, 2020

By K. Szafran, R. E. L. Seal, M. Tansey

Conversion of hydraulic equipment to fire resistant fluids has been hampered by less than satisfactory component performance and in some cases, catastrophic equipment failure. Concern over identifying possible causes to these problems led to a joint research project between the Potash Corporation of Saskatchewan Mining Limited and the University of Saskatchewan. This paper summarizes some of the results and conclusions derived from this joint project. In this study, the research was limited to evaluating the effects of potash contamination on the performance of hydraulic equipment. Two separate types of tests were conducted in order to provide a basis upon which trends could be established. This study concluded that the presence of potash dust in the hydraulic fluid can induce severe wear over relatively short periods of time. It was also deduced that a contaminant free fluid combined with proper fluid maintenance could extend the performance of hydraulic components using fire resistant fluids even under very severe operating conditions, such as elevated pressures and temperatures. Recommendations as to how to achieve this goal and the practicality of doing so are presented.

Jan 1, 1988

By J Hadjigeorgiou

Narrow vein mining, as most types of mining, faces important geotechnical challenges. The specificity of geotechnical challenges in narrow vein mines stems from the nature of the deposits, which are often inclined, discordant and found within fractured rock or faults or in shear zones within country rock. This complicates the construction of representative geomechanical models and limits the applicability of several engineering design tools. Furthermore, in certain cases, the severity of encountered geotechnical problems is considerably greater in narrow vein than in wider orebodies. This paper provides an overview of geotechnical and other challenges in narrow vein mines with a focus on how these are currently addressed. Of particular concern is the use of manual labour working close to the mining face where there is greater exposure to geomechanical hazards. This review concludes with a particular emphasis on understanding the limitations of commonly used engineering tools and techniques to address geotechnical problems in narrow vein mines.CITATION:Hadjigeorgiou, J, 2012. Geotechnical challenges in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 15-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By J. L. Holman

The Bureau of Mines is conducting research to improve technology for the recovery of strategic and critical metals, such as cobalt, nickel, and chromium, that are lost in bulk and particulate superalloy-type scrap because it has not been possible to process mixed contaminated scrap efficiently. The research approach involves melting and casting mixed superalloy scrap into soluble anodes for electrodeposition of Ni-Co alloys by controlled-potential electrolysis. The initial experimental results described in this report are from electrolytic tests us-ing alloy anodes cast from elemental nickel, cobalt, and chromium, the main constituent metals of superalloys. Baseline data and operating parameters are necessary for Ni-Co and Ni-Co-Cr alloys before detailed experiments can be conducted on the more complex superalloy scrap. This basic research assessed the effects of cathode potential, S04:CI electrolyte ratio, electrolyte pH, stirring rate, deposition time, cathode current density, and chromium concentration on cathode current efficiency, alloy deposit composition, and deposition potential at a cell temperature of 55° C.

Jan 1, 1985

By Peter Middendorp

Pile foundations are widely applied in the Netherlands because of the soft soil conditions. One of the popular pile types are cast-in-situ piles, which have to be integrity tested to get accepted. Integrity testing has been applied for more than 30 years, with the number of integrity test performed nowadays exceeding 400,000 per year and subsequently there is a substantial amount of practical experience with this testing method. This paper will deal with some basics of integrity testing and describe some of the techniques that have been adopted in the Dutch pile testing practice, like detection of pile head defects with a spike type hammer pulse, and the site average or pile group average for the qualitative interpretation of measured signals.

Jan 1, 2006

By S. Banisi, H. R. Iran-Manesh, M. R. Shayestefar, H. Shekarchyan

"Flotation circuit of the Sarcheshmeh copper mine processes 41,000 t/d of ore at 0.9% Cu. Chalcopyrite and chalcocite are the main copper bearing minerals which are concentrated in three stages of roughing, cleaning and recleaning. Due to major changes in the reagent addition regime, make-up balls combination, and throughput to the primary mills an increase of 2.6% (from 87.2% to 89.8%) in the sulfide copper recovery was obtained during a period of six years. In order to investigate a rather large variation of monthly recovery (i.e., from 89.0 to 91.2%) of the plant after implementation of the changes, a study was undertaken to trace mineralogically possible causes of such a behavior. During a five-month period, monthly composite samples of feed and tailings of the flotation circuit were taken. At the first stage, the polished sample preparation method and the mineral counting procedure were optimized through a detailed study. Liberation degrees and types of locking of valuable minerals in both streams were determined in three size intervals of +75, +38 and –38 microns. It was found that for both recovery levels (i.e., 89% and 91.2%), there was no significant difference in the liberation degrees of valuable minerals in the flotation feed; the average liberation degree was 57.1% with a standard deviation of 3.1%. On the other hand, in the case of high recovery level (i.e., 91.2%) there was a reduction of 15% in the amount of free valuable minerals in the tailings stream. The highest reduction was found for the -38 micron size range in particular for chalcocite. It was concluded that compared to the grinding circuit the change in the flotation circuit had the significant effect on the plant recovery increase.INTRODUCTIONThe Sarcheshmeh copper ore body contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and currently processes 41,000 t/d of ore. The concentrator has been in operation since 1982. Last year, the concentrator produced 130,000 tonnes of copper and 4,000 tonnes of molybednite concentrate. An expansion to the plant which will increase the throughput by 50% is under construction and will be effective in 2003.After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailings constitute the main component of the plant final tailings. A concentrate with an average grade of 30.5% Cu is obtained after cleaning and re-cleaning stages. At the present time, the average sulfide copper recovery of the plant is 89.8% which varies depending on the operating conditions and ore type."

Jan 1, 2003

By John Dilworth

THE word "development," as used in connection with .mining, is a rather general term and in most instances must be qualified or explained before the exact thought in the mind of the user is made clear. For instance, by the development of a mining district is often meant its entire facilities of mineral production, such as railroads, towns, mine plants, etc. In speaking of the development of a property its prospecting by test pits or diamond drill borings may be referred to; or it may be the mines, strip pits or quarries from which the coal, ore or rock is won. But, as a rule, when the development of an individual mine is spoken of the idea in mind is the system of underground workings by means of which the mineral is recovered and transported to the surface. It is this character f development that is considered in this paper. The discussion will be confined to the ordinary room-and-pillar, system of mining. practically horizontal coal seams that is used in most bituminous coal mines in this country, and to only two phases of this subject; viz., what is properly included under the head of "Development"' as it appears on the books of a coal company or the inventories of an examining engineer, and how its "value" should be determined -by the accountant or engineer. No absolute rule or definite agreement covers these points, yet these questions are far more than academic. Development is often an important part of a mining company's assets, affecting the amount of its invested capital (and hence its rate of taxation under present Federal income tax laws) as well as the value of its total assets and the amounts chargeable to cost of coal and to depreciation.

Jan 7, 1921

By A. Dave Mackintosh

In 2001, at the CIM AGM in Quebec, a paper discussing poor ground conditions in a newly opened area at Agrium?s Vanscoy Potash Operation?s, suggested load transfer around old workings as a possible reason for the early room failure. High closure rates are expected in deeper regions however the rapid failure of walls immediately behind the face resulted in protective guards being mounted on and behind the borer. The high closure and early rib failure continued well past any reasonable distance to be explained by load transfer around old workings and investigations continued into possible reasons other than simply depth. Detailed investigations into the mineralogy and crystal fabric of the ore zone provided one possibility, which combined with a changed borer cutting profile are now believed to have contributed greatly to the poor conditions.

Apr 1, 2005

By Charles H. Morgan

THE case of Henry Cort comprises: (1) the nature of Cort's inventions;, (2) their value to England and to mankind,; (3) the remuneration received therefor by him or his family; and (4) the suitable permanent record and recognition of his services by the representatives of the art lie founded-a debt long over-due, and still unpaid. I. CORT'S INVENTIONS. Under this head, it is unnecessary here to enter into details. The facts have been repeatedly published, and a brief outline of them will be sufficient for my present purpose. . Henry Cort, born in 1740 at Lancaster, England, became a navy broker in. London about 1765, and gained from that business in about ten years. something more than £20,000, which lie devoted to perfecting the manufacture of iron, building a mill at Fontley, near Portsmouth, and prosecuting, between 1777 and 1783, the experiments which culminated in .his two patents, one for puddling iron and the other for shaping it by rolling between grooved rolls.: Careful study of the contemporary evidence, including Cort's specifications, the testimony (in act as well as word) of his business rivals, the public declarations of eminent authorities, and the history of the times, leaves no possible doubt that Cort was the real inventor, of

Mar 1, 1905

By R. W. Raymond

(Pittsburg Meeting, March,1910.) THE Giroux Consolidated Mines Co. is equipping a five-compartment shaft at Kimberly, Nev., which will serve the Alpha mice. The depth of this shaft, January, 1910, is 963 ft., and of this depth 948 ft. was opened by raising, 15 ft. of sinking was done so that the bearers, collar-set, and three shaft-sets might be installed and concreted, and with this done it was possible to erect the necessary surface-equipment for resuming shaft-timbering on the completion of the raise. The arrangement of the shaft-timbering is shown in Fig. 1. At the 1,000-ft. level of the Alpha, and 750 ft. SW. from the Alpha shaft, a 14- by 18-ft. station was cut, and a 25-h-p. air-hoist *as installed. From here the raising commenced on July 5, 1909. The raise was cut approximately 13 by 21. ft. in area, and supported by timbering with square sets, illustrated in Fig. 2, which shows the division into four compartments. The end compartments, which were used as chutes, had the center girts heavier than in the others on account of the wear from falling rock. The chute-lining was braced by inserting 8- by 8-in. stiffeners parallel to and half way between successive caps. Similarly, the lagging on the wall sides of the cage-way and the compartment for pipes and ladder was stiffened with 4- by 6-in. timbers. In the pipe-and-ladder compartment the chute-stiffeners were reinforced with 8- by 8-in, struts, and as the cage-way was partitioned off by braced lining, there was practically no chance of rock entering the ladder-way in case a chute burst into the cage-way. Over the two center compartments the last two, sets were always bulkheaded with 8- by 12-in. timbers, shown in Fig. 3, and from the lower bulkhead the cage sheave-wheel was suspended. After a round of holes had been blasted and the loose

Jun 1, 1910

By Robert Pack

INTRODUCTION SOONER or later in the development of any natural resource it becomes highly desirable to know the quantity of this resource in the country as a whole, as well as of the part that is being developed, for the general course and. conduct of the development work must be governed to some extent by the total supply available. An accurate estimate of the quantity of any natural resource is difficult to make; yet if one is diligent enough one can obtain a pretty accurate idea of the quantity of marketable timber, the acreage of tillable land, or the horsepower that may be developed from the streams, for these are things that may be measured. But any attempt to estimate the quantity of some mineral in the ground appears to enter the realm of imagination and it seems that the estimate can be nothing more than a blind guess. It may appear to be especially futile to attempt to determine the quantity of oil and gas that is available in the ground, for these minerals are so vagrant that even if the quantity now available should be known quite exactly, the quantity that will eventually be obtained may be much less, for certain losses in the extraction of both oil and gas are unavoidable, and just what these losses will be cannot be predicted. Though necessarily inaccurate, estimates of such mineral reserves are, however, of distinct value, for they summarize the existing knowledge of the deposits of the mineral and thus enable those who are interested in some industry that depends in one way or another on this mineral to formulate a rational commercial policy. Some time ago, when the price of gasoline suddenly rose in a rather spectacular manner, the writer was one of the U. S. Geological Survey geologists called upon to help to estimate the quantity of oil that could be obtained in the United States, for the fear had become widespread that perhaps the rate of increase in the price of gasoline was a measure of the rate of depletion of the supply of petroleum. It thus became his

Jan 8, 1917