Search Documents

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., Lafayette, CA, under contract to the U.S. Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1990

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibration limits for buildings with respect to ground vibrations from pile driving published in international standards are reviewed. At first, relevant vibration parameters are defined and the evaluation of vibration records is described. The sensitivity of structures to different vibration parameters (displacement, velocity and acceleration) is discussed. Most vibration standards relate to blasting activities, the dynamic characteristics of which can be significantly different to those from construction activities and in particular, pile driving. Several vibration standards are reviewed. The Swedish vibration standard is described in detail, as it is the only one accounting for several important factors, such as ground conditions, building material, and type of building foundation. Many standards limit the guidance to values based on the dominant vibration frequency and a wide scatter of frequency-dependent vibration limits exists. It is difficult to compare limiting values of ground vibrations proposed in different standards.1. INTRODUCTIONFor poor ground conditions, placing structures on piles is the most common foundation solution, while sheet piles are widely used to support deep excavations. Piles and sheet piles must often be installed in the close vicinity to buildings, structures or installations in the ground, which can be affected by ground movements and vibrations, (Massarsch and Fellenius, 2014). In many areas, environmental concerns with respect to noise and ground vibrations can restrict or even prohibit driving of piles or sheet piles or reduce the efficiency of installation. The design engineer must prescribe – often at an early stage of a project — the permissible levels of ground vibrations in order to minimize the potential risk of building damage. When seeking guidance from the literature, little or practically no applicable information can be found on how to assess permissible levels of ground vibrations."

Jan 1, 2014

By Arash Nikvar-Hassani, Lianyang Zhang

To address the drawbacks of the conventional portland cement/fly ash (PC/FA)–based cementitious material currently used in practice to construct pumpable roof supports (PRSs), a novel cementitious material has been developed based on geopolymerization technology. The novel cementitious material is comprised of two pumpable grout streams: Stream 1 is a slurry composed of pozzolanic material and high-calcium additive and stream 2 is an alkaline solution comprised of a gelling agent. Biopolymer has been added to the second stream to provide ductility to the geopolymer cementitious material. In the laboratory scale, systematic experiments have been carried out to investigate the viscosity, setting time, and uniaxial compressive strength (UCS) of the new cementitious material and develop the right recipe for field applications. By collaborating with industry and the National Institute for Occupational Safety and Health (NIOSH), full-scale PRSs have been constructed and tested. The results show that (1) the novel cementitious material based PRSs has much higher peak UCS and similar or higher residual strength than the conventional PC/FA-based PRSs; and (2) unlike the PC/FAbased cementitious material, the novel cementitious material shows good long-term durability with nocracking/disintegration when exposed to air.

Jul 1, 2023

By Türker Hüdaverdi, Özge Akyildiz

"In this research, image analysis technique, Kuz-Ram and KCO Models were used to examineefficiency of the quarry blasts. Investigations were performed in Cendere region, Istanbul. As a firststep, image analysis software was used to determine particle size distribution of muckpiles.Additionally, the results of KuzRam and KCO fragmentation models were compared to the results ofthe image analysis technique. The efficiency of KuzRam and KCO models was investigated and theimportant points to be considered were explained. Additionally, the effect of the rock factor valueson the size distribution curves was investigated. The blasthole diameter is 89 mm. (3.5 in) in thestudied quarry. Each measured blast has a different burden, spacing and stemming length. Blastholes was drilled in a staggered pattern. It is concluded that, KuzRam and KCO models can be successfully used to determine fragment size distribution in Cendere Region Quarries, Istanbul. Site engineers can predict blast fragmentation using the theoretical fragmentation models and they may change blast design parameters before blasting operation if necessary. It is possible to calibrate the Kuz-Ram and KCO fragmentation models using the measurements obtained by image analysis technique."

Jan 1, 2016

By William L. Porter

From the first day of new miner training until the day they retire, mine workers will experience changes due to the normal aging process. It is an unfortunate fact of life that many age-related changes result in diminished physical, sensory, or cognitive capabilities. Of course, workers also gain a tremendous wealth of experience, knowledge, and insight as they age, making them a vitally important resource for their company. Effective leveraging of this precious resource requires both an appreciation of the changes that occur with age and an understanding of methods that can be used to reduce the injury risk that may result. The purpose of this training is to provide the information necessary to accomplish these objectives. Aging workers may not necessarily have a higher injury risk overall; however, the effects of a musculoskeletal injury (MSI) on older workers may be more extreme. MSHA data show that not only does the percentage of MSIs increase when workers are over age 30, so does the number of days lost per injury, as shown in the graph below [MSHA 2005]. [ ] Protecting the safety and health of aging workers requires matching the demands of the job to worker capabilities. This means reducing or eliminating risk factors for injuries, such as heavy lifting, awkward postures, static postures, repetitive movements, and/or vibration exposures. In other cases, it may mean improving visibility or streamlining processes. Designing jobs to accommodate the changing capabilities of older workers will not only reduce injury risk for older workers, it will have the added benefit of protecting younger employees as well.

Jan 1, 2008

By Paul Schmidt, John Barber

This paper discusses the determination of cutoff grade (COG), including all revenue and cost factors and how to apply the COG in the world of engineering studies and mine planning for underground mines. It provides the engineer with important considerations and practical methods to establish COG and methods of using the COG in the work of mine planning, including the application of Mineable Stope Optimizer (MSO) software which is available on several 3D mine planning packages.

Feb 1, 2024

By Jochen Petersen, Steven Bradshaw, Guven Akdogan, Ngoie Mpinga, James Mwase, Jacques Eksteen, Cornelius Snyders

"The platinum group metals (PGMs) and associated minerals are particularly refractory to most traditional direct leach processes. However, the remoteness of many new ore deposits, socio-political risks, the scarcity of skilled labor and constraints on the availability of water and electrical power makes it increasingly more difficult to implement the conventional mill-float-smelt-refine process routes to extract and refine PGMs in remote areas. This paper discusses a process to extract PGM’s from low grade ore and concentrate using a sequential stage heap leach process entailing heap bioleaching and high temperature cyanide leaching, and evaluates the feasibility of implementing a carbon-in-pulp process to recover the PGMs from the pregnant leach solution. The heap bioleaching extracts the base metals in an acidic sulfate medium using a mixed culture of thermophiles. After heap bioleaching the heap is reclaimed, rinsed, agglomerated and restacked for high temperature cyanide leaching where the cyanide liquor is directly heated via solar energy in panels. Palladium, gold and platinum are recovered during the cyanide leaching stage. The pregnant leach solution was evaluated for potential carbon-in-pulp adsorption and subsequent elution similar to gold processing. The kinetics of adsorption and elution compared well with gold adsorption and elution."

Jan 1, 2014

By B. P. Watson

The Bushveld platinum group metal deposits are two distinct, shallow-dipping stratiform tabular orebodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 000 m. The mining method is a variation of planar open stoping. Pillars are widely used to support the openstopes. Little work has been done in the past to determine pillar strength and pillars have been designed using experience and formulae developed for other hard-rock mines. This has led to oversize pillars with consequential loss of ore or undersize pillars resulting in potential collapses or pillar bursts. This paper describes a back-analysis of pillar failures at Impala Platinum, just north of Rustenburg, and provides insights into pillar behaviour. Strength formulae are presented for Merensky Reef pillars at Impala. These formulae may be used cautiously on other platinum mines with similar geotechnical and geomechanical conditions.

Jan 1, 2008

By M. du Plessis, D. F. Malan

"The aim of any mine design is to ensure that the excavations remain stable for the period they will be in use. Various pillar systems are used to ensure that underground stopes remain stable and that mining activities do not affect the surface infrastructure through either surface subsidence or seismicity. Intermediate-depth platinum mines make use of in-stope pillars designed to fail while the pillars are being cut at the mining face. The pillar stress exceeds the loading capacity and the pillars crush as a result. The aim of the paper is to provide an overview of in-stope crush pillars. This will include the application, behaviour, function, mechanism, impact, and design of a crush pillar system."

Jan 1, 2015

By George K. Schenck

This Bureau of Mines publication describes and evaluates a Standard Industrial Classification (SIC) based end-use data system for minerals that is designed to link the demand for minerals to economic activity in commercial uses. The new data system is two-dimensional. The first dimension of technical product classes (TPC's) measures the consumption of minerals in major primary intermediate products. The second dimension measures the consumption of these TPC's in SIC end-use sectors in sufficient detail to identify the major determinants of demand for each TPC. Intercomodity comparisons are achieved at the level of SIC two-digit major groups. The methodology was developed so that all available sources of information from Government and industry can be utilized at minimum cost. This information will be supplemented with additional data to be obtained by modifying existing Bureau of Mines canvasses so as to elicit additional quantitative responses from mineral producers. The new data system is expected to improve significantly the ability to forecast demand for minerals, and provide an information base that would, for the first time ever, permit resolution of such questions as trends in substitution among materials and the intensity-of-use of materials in end-use sectors. For the 42 TPC?s identified in the report, data are available for the new system from current sources or, except for three TPC?s that require new canvasses, can be obtained by modification of existing Bureau canvasses.

Jan 1, 1982

By Kodi Ranga Swamy, N. Sankar, M. Akhila

"Until recently, liquefaction-related studies concentrated on clean sands believing that only sands are susceptible to liquefaction. However, a few earthquakes like 1976 Tangshan earthquake, the 1989 Loma Prieta earthquake, the 1999 Kocaeli earthquake, the 2010 Chile earthquake, and the 2011 Christchurch earthquake, etc. showed that sand with fines could also liquefy. The research findings on liquefaction of silty soils are limited, and several structures constructed on such soil deposits are damaged during the past earthquakes. Some previous results of research on earthquake events show an increase of liquefaction resistance in silt soils with increase the fines content, but some report the opposite trend. This study presents the results based on undrained triaxial cyclic tests which were carried out on the fine sand with fines (0%, 10%, 20% and 40% fines). The samples were prepared at the required unit weight (Dr = 50%) and saturated by using back pressure and cell pressure increments. Each consolidated sample is subjected to cyclic loading with sinusoidal wave load form at a frequency of 1 Hz. The liquefaction resistance is evaluated in terms of cyclic stress ratio required to cause 100% pore pressure or 20% failure strain occur at 15 numbers of load cycles. Results are presented in forms of pore pressure build up and axial strain propagation plots. As the fines content increased, an increase in liquefaction potential was observed.INTRODUCTIONLiquefaction and related phenomenon have been responsible for tremendous amounts of damage all around the world. In general, the liquefaction may occur in fully saturated sands, silts and low plastic clays. When the saturated soil mass is subjected to seismic or dynamic loads, there is a sudden buildup of pore water within a short duration, and it could not dissipate which leads to reducing the effective shear strength of soil mass. In this state, the soil mass behaves like a liquid and causes large deformations, settlements, flow failures, etc. This phenomenon is called soil liquefaction. As a result, the ability of soil deposit to support the foundations of buildings, bridges, dams, etc. is reduced. Liquefiable soil also exerts a higher pressure on retaining walls.This lateral movement of soil could cause settlement of the retained soil. A sudden build-up of pore water pressure during quake also triggers landslides. Liquefaction damages of structures are commonly observed in low-lying areas near the rivers, lakes, and oceans."

Jan 1, 2017

By Raymond A. Binns

The Eastern Manus Basin (EMB) contains three major active hydrothermal zones and a number of smaller occurrences of hydrothermal deposits, and can be considered as a regional-scale modern analogue for volcanic-hosted mineral fields on land. Unlike the central Manus Basin, a back-arc spreading zone with some MORB-like basalt-hosted massive sulfide deposits, the EMB is a pull-apart rift zone between two transform faults, where a basement of Eocene-Oligocene arc crust is being thinned by extension, with rapid sedimentation on the tilted fault blocks. Present-day submarine igneous activity in the EMB, with which hydrothermal activity is associated, has arc geochemical affinities and is related to subduction of the Solomon Sea Plate at the New Britain Trench. Overall, hydrothermal deposits in EMB are found with lavas ranging from picritic basalt to rhyodacite in composition, although the two major occurrences of massive sulfide are hosted by the more siliceous dacite and rhyodacite variants. Some volcanic edifices are central eruptions, mostly of porphyritic lavas or domes, while others are elongate ridges formed by fissure eruption in which the typically aphyric lavas were very fluid. Evidence for shallow-level fractional crystallisation controls of lava chemistry implies presence of subjacent differentiated intrusions or former magma chambers. Seismic tremor at one site during the nearby 1994 Rabaul eruption suggests magma movement in the chamber.

Jan 1, 1998

By Fred C. Schmednecht

For years, the strategy was to contain waste and in many applications, is still the recommended method. Recently, it has become acceptable to create filters below ground for the in-situ treatment of waste. Consequently, in lieu of the waste being contained, it is desirable that the waste flow through a pervious treatment zone. For instance, subterranean pervious walls comprised of iron sand are particularly useful in treating chlorinated solvents in contaminated groundwater. The iron acts as a corrective filter to treat the contaminated groundwater. How are these impervious and pervious walls being constructed? One effective means of constructing an impervious barrier is the vibrated beam method. This method, in brief, involves the use of a fabricated steel beam, a vibrator, a pile driving crane, and a mixing plant. This method results in a 4-6" wide wall with depths up to and exceeding 100'. Over one hundred slurry walls have been installed using this method in the United States. The need for the vibrated beam method continues to escalate due to its reduced health and safety considerations, high level of quality control, lack of excavation, narrow working area, and ability to achieve depths greater than 100'. A recent project was in Marinette, Wisconsin at the ANSUL facility. The project consisted of a 28,000 square foot slurry wall and was completed in January of 1999. Another effective means of creating an impervious barrier, where structural support from the barrier is needed, is the Waterloo® Barrier System. This system involves the use of a pile driving crane, Waterloo® steel sheet piles which are patented steel sheet piles due to their groutable interlocks, and a grout plant. This system results in a water-tight barrier due to the grouted interlocks and provides structural support. A project was completed at Beta Steel in Portage, IN for a retention pond to protect Lake Michigan. Due to the new concept of "filtering", there are few accepted construction techniques available. One effective field proven construction technique is the patent pending mandrel emplacement technique. This technique involves the use of a fabricated hollow steel mandrel with a shoe, a vibrator, a heavy duty crane, and a material feeder. This technique results in a pervious wall which may be comprised of pure iron sand or any other flowable media. Using this technique, the pervious wall may be constructed in varying widths to depths in excess of 100'. A successful installation occurred in October 1997 at Cape Canaveral Air Station in Florida.

Jan 1, 1999

By E Heath, F McDermott, S Turner, P van Calsteren

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath midocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and om, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100 000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50 000 years prior to eruption.

Jan 1, 1995

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, pro- [ ] duced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. [ ] The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. , I). Above the sand rock an overburden of Joachim limestone appears, which, thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes, where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OT THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By John H. Hild

This is a report on work done and results obtained in a minerals exploration program conducted by the Bureau of Mines on the lead-zinc deposits in the Ross Basin-Lake Como district, San Juan County, Colo., in 1948, 1949, and 1950. Four large veins--the Seven Thirty, Red Rogers, Cashier-Shorts top-Canandaigua, and Queen Anne--and several narrow spur veins were explored at relatively shallow depths with core-drill holes. Thirty-nine holes, totaling 10,491.5 feet, were drilled, and the core samples were assayed at the Bureau of Mines station at Salt Lake City, Utah.

Jan 1, 1959

Henry Walker Eltin (HWE) are the mining contractors for Gloucester Coal at Stratford mine, which is in an environmentally sensitive area in the Avon Valley, NSW, Australia. Normal blasting at Stratford is done in a “stand up” or “box cut” mode to suit the truck and shovel operations. Recently an opportunity of doing a throw blast became available when part of a ramp had to be blasted to accommodate changes to the pit design while not damaging the remainder of the ramp. The objective was to maximise throw into the void in order to minimise excavation costs by reducing the amount of overburden to be moved by the excavation fleet. It was necessary that the best result be achieved while staying within the vibration and airblast limits at a neighbouring property and nearby township. Both objectives were achieved through the application of Orica’s knowledge of blast design, modelling and i-konTM electronic detonators.

Jan 1, 2003

By Edwin F. Shorey, Richard F. Coon, Steven B. Fradkin

Crosstown Interceptor Phase IA is the first deep tunnel element of the Milwaukee Inline Project. The tunnel contract includes 6,492 meters (m) of 9.1-m-diameter tunnel, two access shafts, and partial lining for structural purposes. The work also includes grouting to be performed as directed by the engineer to provide groundwater infiltration control in lined and unlined reaches of the tunnel. This paper summarizes infiltration observations, progress of the grouting work, and its potential application to the remainder of the Milwaukee project.

Jan 1, 1987

By A. Z. Dimitroff

Immediate detection of methane buildup or of sudden liberation of large quantities of methane in the face area is essential to avert disasters in coal mines. Proper timely detection and handling of methane have always presented problems in extremely gassy mines, and these problems have been magnified by present accelerated mining methods. Strict rules and regulations have been established by coal-mining companies, States, and the Federal Government, which provide for periodic inspections for methane in face areas when electrical equipment is working. Other provisions require the operator' to shut down electrical face equipment and change or adjust ventilation when more than 1.0 percent of methane is detected. Nevertheless, human failure to detect such conditions has been responsible for numerous ignitions arid explosions Recognizing this fact, Marling J. Ankeny, former Director of the Bureau of Mines, proposed in 1958 the development of an automatic methane-monitoring device. He envisioned such a device as being entirely dependable, capable of giving a warning when a predetermined concentration of methane in air is reached, and capable of deenergizing the equipment and rendering it inoperative when a dangerous concentration of methane is present in the air. Such a device has been developed by the Bureau of Mines Health and Safety Research and Testing Center in Pittsburgh, Pa.

Jan 1, 1967

By A. J. Thompson

The Metropolitan Transportation Authority (MTA) East Side Access project (ESA) will, when it is complete, provide a new link to the east side of Manhattan from Long Island, NY that, linked with the Second Ave. Subway currently under construction, will assist in relieving overcrowding at Penn Station as well as the Lexington Ave. subway. ESA will bring Long Island Railroad (LIRR) directly from Long Island into a new station located 37 m (120 ft) beneath the existing Grand Central Terminal (GCT) located in the heart of Manhattan. It will connect the LIRR?s mainline tracks in Queens, via the existing 63rd Street Tunnel under the East River, to a new terminal constructed within, and beneath, the historic Grand Central Terminal.

Jan 1, 2012