Search Documents

By Terry R. Neumann

In 1987 and 1988, the U.S. Bureau of Mines conducted a mineral resource investigation of the 31,400-acre Muddy Creek Wilderness Study Area (UT-060-007). The investigation was requested by the Bureau of Land Management and authorized by the Federal Land Policy and Management Act of 1976 (Public Law 94-579). The study area is located in Emery County, Utah, about 50 air-miles southwest of Green River, Utah. The wilderness study area is in the San Rafael Swell region of the Colorado Plateau Physiographic Province. Rocks in the area consist of gently dipping sedimentary strata of Permian, Triassic, and Jurassic age.

Jan 1, 1988

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983

By H. Fayed

Two-phase (water and air) flow in a self aerated WEMCO flotation machine has been investigated using computational fluid dynamics (CFD). A 0.8 m3 model is considered. The flow is modeled by Euler-Euler approach, and transport equations are solved using a commercial software ANSYS-CFX5 [1]. Because of the lack of circumferential periodicity in this machine, the entire machine is modeled and unsteady simulations are conducted in the whole volume of the bulb. Uniform bubble diameter is specified, and the effects of bubble diameter are determined by conducting simulations for three diameters of 0.5, 0.7, and 1.0 mm. The unsteady air flow rate through the machine is predicted as an outcome of the simulations. Air volume fraction contours and velocity field in different parts of the machine are presented and discussed.

Jan 1, 2012

By D. Bour, C. Nyikos, R. Curtice

Fire in a coal mine can be disastrous on many levels. In most cases, when a fire is detected, mining operations cease and all personnel are evacuated. Underground coal-mine fires are difficult to extinguish, can burn for a long time, and often result in an extended period of lost production. In a worst-case scenario, the mine is permanently sealed and abandoned, resulting in lost jobs, lost natural resources, and possible devastation of the local economy. In some cases, seals placed within the mine to isolate the fire could eliminate the need for sealing the entire mine and the subsequent extended delay in returning the mine to full operation. Previous attempts to place remote seals to extinguish mine fires in active mines have been largely unsuccessful. The West Elk mine experienced an underground fire in early 2000. The fire could not be accessed and extinguished from the active mine workings. A method of constructing seals remotely by drilling boreholes into the affected area was needed to help isolate and extinguish the fire. This paper describes the process by which remote seals were constructed that successfully isolated the fire and provided a means of extinguishing the fire by flooding the area with water. The period of lost production in the West Elk mine was considerably shorter than is typical in similar situations.

Jan 1, 2002

By AIME

IN the following pages are described the history and present operations of one of the country's great mining and metallurgical organizations-the United States Smelting Refining and Mining Company. Though the articles are largely of interest to the technical man, the success of the Company as a business enterprise should not be overlooked. Almost immediately following incorporation 42 years ago payment of dividends began and the total to date has been about $140,000,000, roughly half to preferred and half to common shareholders. Founders of the Company were Boston businessmen and financiers interested in such diverse enterprises as shoe machinery manufacture, banking, newspaper publications, and stock brokerage. The legal profession also was represented. The Company is one of the few, among the leaders in the mining industry, that has resisted the urge to move its home office to New York and has always remained in Boston. Perhaps for that reason it has been regarded as a "conservative" company. Conservative or not, it has certainly spread out geographically and it has certainly put its eggs in many baskets. In addition to the precious metals and the major nonferrous metals it has ventured into coal and recently in a small way into the field of oil and gas. It seems to have a predilection for the North American Continent; for in addition to Alaska, Canada, and Mexico it has had important operations in California, Arizona, Nevada, Colorado, New Mexico, and particularly in various districts in Utah.

Jan 1, 1948

Case I- Timber Pile Test- 4 pages describe the pile driving record, the pile load test and the boring log. Case II- 24 inch square prestressed concrete pile-5 pages give details about the pile driving, the boring log, the pile driving record, and the pile load test. Case III- 12 inch square prestressed concrete pile- 5 pages describe the compilation of SPT blow counts for the whole project, the pile driving record, the pile load test and the detailed boring logs. The 70 foot long pile was driven by a Vulcan 08 pile hammer. Case IV- 12 BP 53 Steel H pile- 3 pages give the pile load test, the pile driving record and the nearest boring log. The 64 foot long pile has its tip at elevation 908 ft. and the ground is at elevation 972 ft. The contractor augered to elevation 959 ft. before driving the pile with a Conmaco 08 single acting pile hammer. The hammer had an 8000 pound ram, a rated energy of 26,000 ft-1b., and a 7 1/2 inch thick asbestos cushion. Dynamic measurements were made during driving of the test pile and measured a hammer energy equal to 12,500 foot-pounds.

Jan 1, 1988

By Rosaire Emond

Le concept du forage horizontal a été développé voilà de nombreuses années. Différents types de plate-formes permettant le forage horizontal depuis une cheminée ont été conçus par divers manufacturiers ou opérateurs miniers. Entre autres, on connaît bien la griffe de montage Alimak à laquelle peut être fixée une plat-forme sur laquelle est montée une foreuse. En 1992, Ross-Finlay a développé sa propre plate-forme de forage qui à notre opinion améliore la flexibilité du concept du forage horizontal, en augmente la productivité et en diminue le coût d?ensemble tout en assurant une sécurité accrue des travailleurs. Tel que montré à la figure 1, la plate-forme employée à la Mine Kiena est composée d?un toit de protection contre les chutes d?objets et de deux passerelles de forage de forme carrée. Le toit et les passerelles sont fixées à une structure de 6.5 m de longueur équipée de deux assemblages de rouleaux (non montrés à la figure) permettant de faire glisser l?ensemble sur des rails Alimak. L?angle du toit et des passerelles peut être ajusté pour des cheminées dont le pendage varie de 65 degrés à 85 degrés.

Oct 1, 2001

By M. Lahtinen, P. Latostenmaa, I. Kojo, E. Peuraniemi, M. Lindgren, S. Jyrkönen, M. Jåfs

The year 2019 marks the 70th anniversary of Flash Smelting. The technology was operated on industrial scale for the first time at the Outokumpu Harjavalta copper smelter in Finland in 1949. Since then Flash Smelting technology, now owned and developed by Outotec Oyj and the first plant, now owned by Boliden Harjavalta Oy, have been evolving throughout history by optimizing the process for various feeds and raw-materials, as well as through developing the equipment and operating practices. Even though sustainability was not a popular theme during the first days of Flash Smelting, it has still been the key principle in guiding the development. This is well proven by the wide adoption of Flash Smelting for the processing of copper and nickel concentrates, mostly due to its ability to fulfil the economic and resource efficiency criteria demanded by its operators. This paper describes the history and improvements of the Outotec® Flash Smelting process by looking into the early days of operation and how the development of the process and equipment has taken place over time as a joint effort between the technology provider and the users of the technology. INTRODUCTION In the 1940s, Outokumpu Oy refined the concentrate produced in the Outokumpu mine into metallic copper initially in Imatra, and later from 1945 to 1949 in Harjavalta, based on the most modern electrical melting process of the world at that time. After the war, Finland lost a significant part of its hydropower production, and due to the increasing use of electricity, the availability of electricity weakened, and the price rose. To maintain Outokumpu's profitability, it was forced to look for a melting solution that was not based on electricity.

Jan 1, 2019

By Joel K. Waterland

The Homestake Mining Company at Lead, South Dakota is one of the few remaining gold properties still in operation, in this country. The mine is relatively deep, with a bottom production level of 4250 feet, and a bottom development of 6200 feet. 4, 800 tons of ore are produced daily from three rather large, but inconsistent ore bodies; the dip of which is easterly at about 72 degrees, and the plunge to the south is about 30 degrees. The ore is, for the most part, a chlorite schist with large veins of secondary quartz and cummingtonite schist The ore is not continuous in any direction, but is localized at the ridges of the very intricate system of anti clinal folds. This property has been in active production since its establishment in 1876, except for a period during World War II. The incentive, or contract pay system, has been a gradual process that has been developed by the trial-and-error method down through the years. In looking over the old records, hand-shoveling was paid on an incentive basis as far back as 1916. Since this time, the contract system has grown until it now includes almost all types of underground work - except haulage and maintenance work

Jan 1, 1960

By D Teyhan, J Kirsch

Traditionally, most Australian iron ore mining operations have been surface-based. Processing plants were designed to handle dry ores. In recent years mining operations in the Pilbara have progressively moved below the water table exposing wet, sticky ores which have caused lost efficiency in screening operations as particles tend to agglomerate and adhere, blinding screening media. Miners and vibrating screen manufacturers have experimented with a shift from linear motion to elliptical motion screens. Elliptical motion conveys and lifts particles. Effective on flat deck (horizontal and inclined) or sloping decks it can be configured to provide a controlled transport rate, applying pressure in all directions to maximise screening efficiency. In practice, elliptical motion screens have proven to be effective in dislodging sticky particles from screening media, reducing blinding rates and improving screen efficiency. Moisture and clay content change during the life of a mine. These changes are sometimes the effect of seasonal rainfall, in other cases due to increased groundwater and clay content as mining operations go deeper. To compensate for such changes and optimise screen efficiency, changing the ‘shape’ of elliptical screen motion is required. This has traditionally required shutting down processing plants and making mechanical screen adjustments. Plant downtime is costly and machine adjustment has been a ‘trial and error’ practice. This paper will explore the results of a field trial that is currently underway in Brazil of a next generation elliptical motion screen design that allows operators to make changes to exciter rotational direction, speed and screen stroke angle, through electronic drive phase control. The machine’s electronic drive system synchronisation is enhanced for stability with a unique mechanical timing system. Operating at up to 6 g, screen adjustments can be made on the fly without stopping production. Early trial results are showing up to 50 per cent improvement in screen efficiency compared with traditional elliptical motion machines under certain feed conditions.

Nov 8, 2021

By Robert W. Metcalf

Corundum, natural alumina, or aluminum oxide (A1203) is the hardest mineral known except diamond. Theoretical composition is Al 52.9 percent and 0 17.1 percent, but it always contains small quantities of impurities, chiefly silica, iron, and lime. The melting point of corundum is above 1950° C., and it is insoluble in the strongest acids. Its hardness (9 on the Mohs scale) varies slightly according to purity, and its specific Gravity ranges from 3.95 to 4.10, 4 being a fair average. The index of refraction is 1.760 to 1.768 and its streak is white. Luster is adamantine to Vitreous, come specimens pearly, and color varies widely from white, gray, pink, and blue to black, brown, or bronze. Gem varieties are transparent or translucent, and of more brilliant coloring - red, blue, yellow, purple, or green. Corundum occurs in opaque massive or block structure with parting planes little developed or only roughly delineated and in granular form as minute crystals or small, irregular grains interspersed throughout the contact zones of schists and gneisses.

Jan 1, 1944

By C. L. Schneider

The problem of predicting the liberation spectra produced by a closed continuous grinding circuit is of fundamental importance for the design, optimization and control of most operations in an ore dressing plant. The only known approach through which such a calculation can be performed is the population balance model equation. The latest and certainly most significant progress made in this area is the solution proposed by King (1990), which requires one textural parameter that can be measured directly from the ore being studied. The main advantage of King's solution is that it does not require the estimation of hundreds of arbitrary parameters that cannot be independently measured, as required by the existing conventional solutions. However, King's solution relies heavily on a knowledge of the detailed internal structure of the Andrews-Milm diagram (Andrews and Mika, 1975). This has never been measured for any ore. The characterization of the internal structure of the Andrews-Mika diagram requires the measurement of the liberation spectra at several progeny sizes produced by the breakage of monosize, monograde particles at several different grades. In this paper, a procedure based on magnetic fluid fractionation for generating seven narrow-size, narrow-grade samples is presented. Each of these samples was then broken into six progeny size classes in an ultrasonic mill. The one-dimensional liberation spectra of each of the 42 progeny and seven parent particle samples were then measured by image analysis. The measured linear-grade distributions are presented in this paper. The calculation of the correspondent volumetric-grade distributions is discussed.

Jan 1, 1994

By D. A. Wheeler, Rémi Tremblay

"INTRODUCTIONDuring the last few years, through Column Flotation Company of Canada ltd, the Centre de Recherches minérales has worked on the column flotation of coal, phosphate, feldspar, talc, graphite, copper, lead-zinc and diamond ores. The operating companies and prospective deposits were located in Canada and in other countries. Since these projects were financed by the concerned mining companies, all results remain confidential unless we obtain permission to publish. Three companies have graciously allowed us to use their information which I will describe in this text. These are the Polkowice copper mine in Poland, the North Coast Industries ltd graphite deposit and a talc company which preferred to remain anonymous. I will also describe our 2 inch column which was used for all tests. Data is also given on how to scale-up the 2 inch column to industrial size.Figure 1 presents a schematic of a flotation column. Feed, at a controlled rate and pulp density, enters at about 1/4 of the height of the column from the top. A controlled rate of air is bubbled into the bottom of column through a fine-holed sparger. The column volume between the feed point and the top of the sparger is called the recovery zone. Tailings, at a controlled rate, always slightly greater than the feed rate, discharges from the bottom of the column. This difference in feed and tailings flowrates is called the bias. The floated mineral is carried through the recovery zone on air bubbles which rise into the cleaning zone which is that column volume between the feed point and the overflow at the top. As the bubbles rise in this zone they are washed of gangue material by wash water which enters over the top of the froth layer. The froth layer is maintained at a given depth during flotation but this depth will depend on the froth cleanliness, for quite a bit of cleaning by wash water is accomplished in this layer."

Jan 1, 1988

By Robert Hopler

This article, advocating having employees whose specific job would be to fire blasts in underground coal mines in llinois, was written 5 years prior to the establishment of the U.S. Bureau of Mines, and 2 1/2 years before the worst month in U.S. coal mining history, when 692 miners were killed in three separate explosions in December 1907. Obviously something had to be done to improve safety in the use of explosives, and having dedicated shotfirers was a good first step.

Jan 1, 2006

By E. T. W. Bailey

A HISTOR Y of the development and application of instruments, from the simplest U gauge to a modern indicating recording controller, would contain many interesting accounts of difficulties experienced and over-come. Important as is the history of development to any branch of science, this phase will, of necessity, have to be omitted from this paper and remarks confined to the results from the use of instruments in their present form. The steel industry bas, in the past decade, become increasingly instrument minded. More than ever, economy and adherence to doser specifications are demanded, and any tool that will aid in attaining these objectives by intelligent application and use finds a ready acceptance. The open-hearth furnace bas offered a field for instruments which is different from almost any other and one in which even a small percentage saved in operating costs may represent a considerable sum. Nevertheless, this department of the steel industry has been more cautions than most others in accepting the benefits which automatic control bas given on many other types of industrial furnaces, and one is puzzled why open hearths have not more generally benefited by the application of controlling instruments. The furnace operator bas to adjust the same three main valves that control fuel, combustion air, and stack draft as on most other furnaces, with the additional regulation of reversing the furnace. He is just as aware of the importance of proper draft control and correct air volume to burn most economically the applied fuel as any good boiler-plant engineer. What, then, are the special conditions that pertain to the open-hearth furnace?

Jan 1, 1939

By R. W. Boyle

"The concept of using chemical methods in prospecting dates back at least to the middle of the 16th century. Modern methods of geochemical prospecting, however, based on secondary haloes and utilizing trace-element techniques, were first practised in the U.S.S.R. and the Scandinavian countries in the 1930's. After 1945, methods based on soils, stream sediments and vegetation were rapidly developed in the U.S.A., the United Kingdom, Canada, France and other countries.The modern methods of geochemical prospecting owe their rapid development in the 20th century to the following:1.-Recognition of the primary and secondary dispersion haloes and trains that are associated with all mineral deposits. 2.-Development of accurate and rapid analytical methods utilizing the spectrograph and the various specific sensitive colorimetrie reagents, especially dithizone. 3.-Development of polyethylene laboratory ware of all types and the development of resins. This permitted greater freedom of field analyses and reduced the incidence of contamination.4.-Development of gas chromatography. This permitted the rapid and accurate determination of hydrocarbons in petroleum prospecting.Future research in geochemical prospecting should be focused on the following tasks: 1.-Definition of geochemical provinces and their relation to mineral deposits. 2.-Development of methods for discovering large low-grade deposits. 3.-Development of methods for discovering deeply buried deposits. 4.-Further development of methods to outline primary haloes. 5.-Eiucidation and formulation of techniques to relate the size and intensity of anomalies to the grade of the deposits. 6.-Development and refinement of biogeochemical methods, especially those based on indicator plants, chlorotic or toxic effects, and microbiological techniques. 7.-Definition of the types of primary and secondary haloes associated with accumulations of oil and gas."

Jan 1, 1967

By H. S. Price

This report discusses the development of a mathematical model that describes the flow of methane only and methane and water in a coal bed during mining operations. Because of the complex geometry, boundary conditions and fluid properties, the model is based on a numerical solution to the equations describing flow. The goals for the development of this model and requirements to which it complies are for the most part expressly stated in Request for Proposal No. 50110752. In addition to the capabilities specified under the scope of work the model can handle an anisotropic porous medium and a source term has been added which will simulate, somewhat, the effects of desorption. This term will be pressure dependent. The effect of time on such a term is only taken care of in the change of pressure with time. This source term will have the dimensions of Mcf/day/Mcf pore volume. It will be a part of the input data to be supplied by the user and will be entered as a table of rates versus pressure. These models consider the fracture system as the main porosity. All computed results pertain to the fractures. The source term mentioned above represents the flow from the matrix porosity into the fracture. Such flow should be small compared with the flow between fractures since these models handle only one porosity structure system.

Jan 1, 2012

By P. H. Davenport, L. W. Nolan

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Geochemical mapping provides a direct approach to delineating areas of epigenetic mineralisation and for relating the regional distribution of this mineralisation to an overall tectonostratigraphic and structural framework, as well as to extensive areas of hydrothermal alteration. Organic lake sediment is a widely available and effective sampling medium for regional geochemical mapping in Newfoundland, that has proved to be valuable in Au, Sb and W exploration

Jul 1, 1991

By T. Banerjee, D. Felsher, G. Leavoy

"Lake Shore Gold is engaged in commercial gold production at both the Timmins West and Bell Creek mines, located in Timmins, Ontario. Run of mine ore is processed at the Bell Creek mill which consists of a conventional gold mill flow sheet involving crushing, grinding, gravity concentration and carbon-in-leach (CIL) for gold recovery. Since 2009, the operating capacity of the mill has been upgraded from 2000 tpd tonnes per day (tpd) to over 3,000 tpd. The most recent expansion involved the installation of a low aspect ratio SAG mill to replace the secondary crusher. Without operational data on the low aspect mill, combined with a site team that was new to SAG milling, there were many challenges in achieving the target throughput from the circuit. Through the implementation of AwaRE advanced controllers, running in closed loop with PRC fragmentation cameras as well as embedded PARC modules within the Allen Bradley PLC, the site was able to rapidly develop a best operating practise and has been successful in creating a stable and consistent operational environment. The process, lessons learned and eventual solution will be reviewed in this paper.INTRODUCTIONLake Shore Gold is engaged in commercial gold production at both the Timmins West and Bell Creek mines, located in Timmins, Ontario. Run of mine ore is processed at the Bell Creek mill which consists of a conventional gold mill flow sheet involving crushing, grinding, gravity concentration and carbon-in-leach (CIL) for gold recovery. Since 2009, the operating capacity of the mill has been upgraded from 2,000 tpd tonnes per day (tpd) to 3,150 tpd. The most recent expansion involved the installation of a low aspect ratio SAG mill to replace the secondary crusher. This endeavor was split into two phases: the expansion of the back-end (Phase 1) and the front-end (Phase 2) of the mill. Phase 1 of the expansion was completed at the end of 2012 and involved enhancements and capacity addition to the leaching and adsorption circuits, which increased the mill’s capacity to 2,500 tpd. Phase 2 of the expansion commenced at the end of July 2013 and involved the expansion of the crushing and grinding circuits. The expanded front-end of the mill now has a capacity of 5,500 tpd, and processes ore from both Bell Creek and Timmins West mines. The updated flow-sheet, as shown in Figure 1, illustrates the replacement of the two-stage crushing and ball milling circuit with a single stage crusher and a low aspect ratio SAG mill."

Jan 1, 2015

By Walter G. Steblez

The countries of Eastern Europe are former members of the Council for Mutual Economic Assistance (CMEA). Geographically, they are located in Central Europe (Poland, Hungary, Czechoslovakia) and Southeastern Europe, largely in the Balkans (Yugoslavia*, Bulgaria, Romania and Albania*). It is important to remember that all of the countries of Eastern Europe had central planning imposed on them by the Soviet Union during the years following World War II. "Stalinist" policy for industrial development had three important tenets: • central economic planning, or a nonmarket-based command economy with administratively set prices; • economic priorities that stressed the development of heavy industries such as mining, metallurgy (steel) and heavy machine building; and • self-sufficiency at all costs, which was aimed at abolishing reliance on the world capitalist market, or reducing it to a minimum. Essentially, the system of industrialization that was used in the Soviet Union in the 1930s and 1940s was imposed on Eastern Europe. Organic market economic development in Eastern Europe ceased during this period. The flaws of this experiment became apparent when mineral processing facilities were set up in many areas of Eastern Europe that did not have reliable resources. Poland, Hungary and Romania are good examples of this situation. The Soviet Union became the principal supplier of iron ore and other minerals and mineral fuels, not only to these countries but to the Bloc as a whole.

Jan 1, 1992