Search Documents

By Jared M. Green

This paper presents the wall stabilization design and implementation for a 541 linear ft masonry and concrete gravity-type retaining wall flanking the west perimeter of a 7.37 acre parcel in Bronx, New York. This paper will discuss the results of static and dynamic stability analyses performed for the pre- and post excavation phases for the proposed 300 ft wide open-cut of up to 14 ft of contaminated soil below the toe of the retaining wall. The wall stabilization consisted of over 74 inclined drilled and grouted anchor dowels, and 55 tiebacks drilled and grouted to the underlying mica schist bedrock. Three over-lapping rows of jet grout columns were chosen as the foundation solution for the existing retaining wall. This paper focuses on the design, construction and performance of the jet grout curtain wall. The jet grout wall served three purposes: 1) underpinning and excavation support for the removal of contaminated site soils, 2) permanent hydraulic barrier, and 3) resistance against a deep seated failure within the thick clay layer present at the site. The originally designed jet grout wall had unexpected negative effects to the existing retaining wall. The jet grouting program was modified while the Observational Method (Peck 1969) was employed to keep wall movements to a minimum. This paper discusses the diagnostic methods used to determine the cause of retaining wall movement; the implementation of a remedial ground improvement program; the modification to the jet grout installation procedure; and the ultimate performance of the jet grout wall.

Jan 1, 2011

Alabama ranked 19th in the Nation in nonfuel mineral value1 in 1994, down from 18th in 1993, according to the U.S. Bureau of Mines. The estimated value for 1994 was $576 million, a 2.5% increase over that of 1993. This followed a 3.5% increase in 1993 over that of 1992. The State accounted for a little less than 2% of the U.S. total. Nonfuel mineral production in Alabama consisted entirely of industrial minerals; no metals were mined in the State. Bauxite materials mined in the State are a natural mixture of bauxitic clay and bauxite having very low iron oxide content and are primarily used to make refractory (high temperature resistant) products, rather than in the production of primary aluminum. In descending order of dollar value, the top four mineral commodities produced in Alabama were crushed stone, portland cement, lime, and construction sand and gravel. These commodities accounted for almost 88 % of the State's total non fuel mineral value, while crushed stone and portland cement together represented almost 65 % of the total. In estimated mineral production for 1994, Alabama remained first in common clays and first of only two States that produced bauxite; third in lime, kaolin clays, and fire clays; seventh in portland cement and salt; and was one of the top seven States that produce bentonite clays. The State dropped from third to fifth in masonry cement. Production of talc and pyrophyllite resumed in 1994. Compared with 1993, the value of crushed stone, lime, construction sand and gravel, common clays, kaolin clays, fire clays, bauxite, and talc and pyrophyllite increased. Decreases occurred in portland cement, masonry cement, industrial sand and gravel, and dimension stone.

Jan 1, 1995

H. Van F. Furman, Denver, Colo. (communication to the Secretary): There are some statements in Dr. Carpenter's interesting paper which appear to require explanation, if not modification.

Jan 1, 1901

By C. S. Spirakis, A. V. Heyl

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The modified basinal brines, containing partly oxidised sulphur species, scavenged metals from basement rocks and sediments and transported them through the host rock, which contained local concentrations of organic matter. Reacting in various ways with the mineralising solution as temperatures at the sites of mineralisation changed, organic matter caused the precipitation and dissolution of a variety of minerals in the ore zones; it was organic matter that caused all of these reactions to occur at the same sites. Thus all components of the mineralising fluid - salt, water, heat, sulphur and metals - were obtained within the ore district. The siting of the mineral districts was related to the locations of faults through U- and Th-enriched granites beneath sediments containing basinal brines, and the locations of ore deposits within the districts were controlled by local concentrations of organic matter

Apr 1, 1995

By T Sylow, A Correa De Araujo, M Gotelip Barbosa

ArcelorMittal is among the largest world’s producers of iron ore. With a geographically diversified portfolio of iron ore and coal assets, it is strategically positioned to serve the network of steel plants, as well as supply the external global market. ArcelorMittal Mining has a global portfolio of 14 iron ore operating units across Brazil, Bosnia, Canada, Kazakhstan, Liberia, Mexico, Ukraine and the United States. Iron ore products include concentrate for sintering and pelletising, pellets, directly shipped fines and lump ore. This paper presents an overview of ArcelorMittal iron ore mines including iron ore typologies and the annual production of each unit. It will also briefly discuss the processing required in order to obtain marketable products.CITATION:Gotelip Barbosa, M, Correa De Araujo, A and Sylow, T, 2017. Overview of ArcelorMittal mining operations and research and development, in Proceedings Iron Ore 2017, pp 161–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

This paper contains an account of some creep tests on electrolytic lead and some of its alloys. The stresses used in determining creep were 500, 350, and 200 lb. per sq.' in. The alloys contained silver, bismuth, tellurium, antimony and zinc respectively. All were castin vacuo, and tested "as rolled." Tests were done also on electrolytic lead which had been cast in air.The electrolytic lead contained 0.0005% total impurities.The preparation and vacuum casting of this lead have been described in a previous paper in this series. The preparation of the alloys, and the air casting of the electrolytic lead, are described in the next section.EXPERIMENTAL PROCEDURE.Every effort was made to keep the vacuum-cast specimens from contact with the atmosphere throughout their history.The ingots were stored eIther in a vacuum desiccator or immersed in heavy oil. The creep specimens were coated with vaseline except during rolling, etching and photography, which involved exposure to the atmosphere for about 45 minutes all told.It is not claimed that vaseline is a perfect shield against the intrusion of atmospheric gases. Possibly during the months that some tests were in progress the gases diffused through the vaseline and gained a limited access to the lead.Nevertheless, the use of vaseline gave protection that brought the tests nearer the ideal at which the author aimed, *Research Fellow, Dept. of Metallurgy, University of Melbourne.

Jan 1, 1936

Conservation and environmental issues are raising their profile with respect to both demand restraint and electricity supply options. In New Zealand, conservation pressures and energy efficiency need to be seen in relation to the supply system currently in place which has capacity for economic supply of electricity in quantities substantially in excess of the current market. Consequently, energy efficiency and conservation need to be interpreted in relation to the supply system as well as in relation to end use. The relationship between the environment and conservation is strongest when new generation is required. New Zealand's electricity supply system consists of a large proportion of hydro production and this has significant environmental benefits when considered in relation to concerns of global wanning and the greenhouse effect. However, environmental trade-offs in supply options need to take account of both the efficiency of electricity end use, the trade-off between hydro and thermal generation and the inter-regional effects of shifting development options from one region to another. The Electricity Corporation has a high level of consciousness with respect to environmental and conservation issues and this paper demonstrates its own moves to maximise energy efficiency and illustrate the environmental trade-offs for supply.

Jan 1, 1990

By C I. Edwards

Phosphorous is typically present in iron ore either in the mineral apatite, Ca5(PO4)3OH, or associated with the goethitic fraction of the ore. In this paper, we present results that show that phosphorous associated with the goethitic fraction can be removed with a heating pretreatment around 300 176;C for 1 h, followed by a caustic leach with 1 - 5 M NaOH, or a leach with sulfuric acid at pH 0.5. The heating pretreatment is considered to dehydroxylate the goethite to form a haematite intermediate phase, ‘protohaematite’, that reacts during the leach making the phosphorous accessible to the leachant. In the acid leach, ten to 15 per cent of the sample was dissolved to obtain a leach product with 0.08 per cent P. In the caustic leach, as no weight loss occurs, it is proposed that iron species associated with the protohaematite have either not dissolved or have reprecipitated at the high pH values of the leach.For an ore containing apatite as the source of phosphorous, a leach with sulfuric acid dissolved the apatite, lowering the phosphorous levels in the sample. The sample treated contained carbonate minerals (including siderite) that also reacted with the acid, and in practice a balance between the dissolution of the apatite and the carbonate minerals may be needed to minimise acid consumption.

Jul 11, 2011

By S G. Walters

The minerals industry is facing a productivity and investment crisis. The ‘Millennium Super Cycle’ from 2003–2011 was an unprecedented period of growth and investment resulting in increased throughput and development of lower grade resources to meet demand. During the boom quantity became more important than quality with throughput the key metric. This was accompanied by a general trend of decreasing feed grades across all commodities that was offset with higher production volumes.Current industry perception is that feed grade depletion is an unavoidable consequence of ore deposit geology and mass mining technologies for increasingly mature mining operations. In typical crush-grind-float operations value recovery only takes place at ~1–200 micron particle size during flotation, ie 3–4 orders of magnitude size reduction compared to primary feed. For increasingly low-grade deposits the cost of energy and capital intensity required to process and reject low value material at micron scale drives poor productivity. An alternative is to deploy a range of coarse (~10–100 mm) separation and rejection technologies. Grade Engineering® is an integrated approach to coarse rejection that matches a suite of separation technologies to ore specific characteristics and compares the net value of rejecting low value components in current feed streams to existing mine plans.Coarse rejection can be used on size distributions ranging from run-of-mine (ROM) to semi-autogenous grinding (SAG) discharge. Grade Engineering® is based on five rock based ‘levers’ linked to combinations of screening, sensor-based sorting and heavy media separation. These involve exploitation of preferential grade deportment to specific size fractions during breakage: differential blasting to condition grade by size at bench scale; sensor based sorting at truck and conveyor scale; and differential particle density.Grade Engineering® is being developed and implemented by a consortium of over 30 mining companies, equipment suppliers and research organisations. Emerging results from collaborative site activities demonstrate potential for generating significant value, which can reverse the trend of declining productivity due to feed grade depletion.CITATION:Walters, S G, 2017. Driving productivity by increasing feed quality through application of innovative Grade Engineering® technologies, in Proceedings Tenth International Mining Geology Conference 2017, pp 263–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Tristan H. Jones

Rib-related accidents in underground coal mines continue to cause injuries and take lives at a rate of 1.3 fatalities per year for the last 17 years. Prevention of these accidents cannot simply be a matter of installing more rib support, though the eventual final solution will undoubtedly include that component. Ultimately, rib safety will be brought about through an understanding of the causes and mechanisms that cause rib fatalities, and by fine-tuning mining methods and procedures that are currently in place. This paper investigates the factors likely to be most influential in the occurrence of rib fatalities. A careful analysis has been conducted of the rib fatality reports documented by the Mine Safety and Health Administration between 1996 and 2013. The primary outcome is the determination of the relative impact of each type of rib fatality factor and a better understanding of the impact each factor has. Among the rib fatality factors considered, the influence of rib profileis considered for the first time. Mining height, rib stratigraphy, mining cycle, and the standing position of a miner next to a pillar are also considered. Questions are also raised about the current interpretation of rib fatalities due to mining depth, with the indication being that mines operating at the greatest depths may actually have the most respectable rib fatality record among all mining depths. Additionally, a new method of considering rib exposure is developed. Based on the results, recommendations are made for future work. By gaining a better understanding of how particular factors contribute to rib fatalities as opposed to rib failure or stability, it is hoped that future efforts can be more precisely directed towards the desired outcome of fatality reduction.

Jan 1, 2014

By F. D. DeVaney

Manganese-bearing deposits f the Leadville, Colo., district are of two distinct types. Manganosiderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 900 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 18.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By F. D. DeVaney

Manganese-bearing deposits of the Leadville, Colo. district are of two distinct types. Mangano siderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 800 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 19.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

Mining at Waihi on the Martha Hill commenced in 1878 and between 1892 and 1953 produced 35 million ounces of bullion from some 13.5 million short tons of ore from 40 named quartz reefs. The general geology of the ore is recorded in detail with differing interpretations by Bell and Fraser (1912) and Morgan (1924). The reefs and stringers have formed by fissure filling and replacement in mainly quartz andesite dacite flows within the Waihi 'Graben'. The host rocks are extensively propylitised with intense alteration forming zones of kaolin adjacent to the main reefs.

Jan 1, 1979

By G. O. Rading, B. O. Odera, M. J. Papo, R. Couperthwaite

"Platinum-based alloys are being developed with microstructures similar to nickel-based superalloys for potential high-temperature applications in aggressive environments. Since the chemistries of nickel and platinum are similar, Pt-based alloys can be made with gamma prime ~Pt3Al precipitates in a gamma (Pt) matrix. Currently, the Pt-Al-Cr-Ru system is one of the bases for developing Pt-based alloys, where Al allows the formation of thePt3Al precipitate and also gives protection from the alumina scale formed, Cr provides oxidation resistance and stabilization for the L12~Pt3Al phase, and Ru provides solid solution strengthening in the (Pt) matrix. Four Pt-Al-Cr-Ru-V and two Pt-Al-Cr-Ru-V-Nb alloys were made, with compositions based on a quaternary alloy, ~Pt82:Al12:Cr4:Ru2, which hadpreviously been identified as having optimum properties. Four of the as-cast alloys had the targeted two-phase structure of ~Pt3Al and (Pt), and two were single-phase ~Pt3Al. Vanadium partitioned more to (Pt) than to~Pt3Al. There was an improvement in hardness compared to the quaternary alloys. The best addition of V was ~15 at.%; higher additions resulted in brittle intermetallic phases of the Pt-V system. The effect of Nbcould not be ascertained because of its high losses."

Jan 1, 2015

By K. Scalise, M. Teixeira, K. C. Kocsis, J. Parrish

"This paper aims to introduce and discuss a newly developed algorithm, which can be uploaded on smart watches and other mobile devices to inform and protect underground personnel working in hot and humid environments. Using this algorithm, the metabolic rate (M) of a worker can be determined in “real-time”. In addition, besides warning signs and alarm signals emitted by the smart watch, the algorithm has the ability to determine work-rest time periods based on the worker’s physiological parameters (e.g. age, height, weight, gender) and the climatic parameters (Td, Tw, flow velocity). This paper also investigates whether a re-designed auxiliary ventilation system can provide appropriate work conditions in the production stopes. INTRODUCTION An underground environment with high temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to heat-related illnesses such as heat rash, heat cramps, heat exhaustion, and heat stroke. Heat stroke is a serious illness that carries a high risk of fatality, if the underground workers are not immediately treated and the climatic conditions are not corrected (McPherson, 1993). There are two methods used to control the climatic conditions in underground mines: (1) Using ventilation and cooling systems to reduce the thermal stress on the mine workers, and (2) Reducing the heat transferred to the ventilating air from major sources such as: strata, auto-compression, mining equipment, groundwater, blasting, etc. The heat from strata and auto-compression is transferred to the ventilating air at varying degrees, based on factors such as the virgin rock temperature (VRT), the thermal properties of the surrounding rock formations, and the surface air temperature. However, the use of mining equipment and blasting processes can be managed to reduce their contribution to the mines’ overall heat load. To provide appropriate work conditions, selecting the most suitable cooling method depends on the level of heat to be removed, the location of the problem areas, and economic constraints (Brake & Bates, 2002; McPherson, 1993). Because every mine is unique, it is essential to monitor the climatic conditions to select the most appropriate method of cooling. A majority of the time, simply adjusting or re-designing the auxiliary ventilation system can efficiently remove the heat and dilute the contaminants. This may involve moving the ducting system, changing the size of the duct, changing the size of the auxiliary fan, or switching from forcing to an exhausting fan arrangement. If the required air volumes are higher than the existing primary ventilation system can supply, other measures may need to be taken to increase the airflow delivery. This may include regulating the flow in some areas of the mine to increase airflow to the desired area, adding booster fans, or replacing the primary fans."

Jan 1, 2019

By Ludwig Schmidt

The policy of buying crude oil on a gravity basis , recently instituted by the major crude oil purchasing agencies in the Mid- Continent field , has caused a new and vital interest to be taken in the work of the U. S. Bureau of Mines for preventing evaporation of crude . From the early years of the industry oil men have recognized that the gravity of crude oil is usually an index of the gasoline content , but it has not been so generally known that the gravity of the crude oil decreases if evaporation is permitted . In 1919 the Bureau of Mines began a survey to determine the evaporation losses of crude petroleum in its various stages of handling from the well to the refinery , The results of this study are presented in Bulletin 200 ( Wiggins , J.H. , Evaporation losses of petroleum in the Mid- Continent Field , Bulletin 200 , U. s . Bureau of Mines , 1922. ) and Bulletin 225 ( Wiggins , J.H. , Methods of decreasing evaporation losses of petroleum , Bulletin 225 , U. S. Bureau of Mines , ( In press ) The findings of this survey were so startling that soon after the preliminary report had been published , several tank companies began manufacturing vapor- tight tanks for the purpose of reducing these important losses . Since that time the development of this type of apparatus has been so rapid that today , every oil trade journal carries numerous advertisements of vapor- tight tanks and equipment as well as technical articles dealing with various problems in connection with the elimination of evaporation losses , whereas three or four years ago the subject was scarcely even thought of. The present report has been prepared in response to numerous requests for information on the apparatus actually being used to prevent evaporation losses . At this time oil operators are also extremely interested in holding the lighter fractions in the crude oil in order to prevent a lowering in gravity . The practice of removing the vapors from crude- oil tanks by means of a slight vacuum and extracting the gasoline from them is not discussed here .

Feb 1, 1923

By D. H. Horswill

The paper point out considerating how mining activities contributed to sustainability, it is important to consider how exploitation of a finite resource can be regarded as sustainable. The now well–recognized concept of sustainable development holds that society’s pursuit of development that meets current needs should not compromise the ability of future generations to meet their own needs. Sustainability, then, contemplates multigenerational enjoyment of a quality of life that includes social and economic benefits and a healthy environment in which to live. In this sense, the benefits of our activities must always exceed the risks. Many other companies are also making significant inroads along the path to sustainability.

Sep 13, 2001

By Leslie B. English

"HistoricalWHILE DIGGING caves and underground passages for living quarters, primitive man must have had some means of illumination. Most likely he used pieces of wood or slim bundles of reeds or grasses as torches, perhaps steeped in animal fats to give more light. If this is so, we may accept these as the first means of underground illumination. Very little was clone to improve lighting devices for many generations, but slowly there was developed a fount holding fatty oils, with a spout in which was inserted a form of wick.Actual mining. for metals first of all, was started about 3,000 B.C. Some of the old Greek and Roman records refer to the use of torches underground, and some evidence of clay lamps has been found. Candies came into use some time during the first century A.D. When coal mining began about the 14th Century in England, candles were used for illumination because of the ease of manufacturing and handling them. Open oil-lamps came into use early in the 16th century -Agricola, in his De Re .Metallica, written about 1540. pictures a miner with such a lamp. However, the expense of these was so great that candies still continued as the general means of underground lighting.Unfortunately, as miners went deeper underground, they encountered a mysterious gas which. upon coming in contact with open lights, flamed violently, resulting in explosions and accompanying loss of life. The first reference to the results of these gas explosions appeared in 1621. No help seemed to be available. The gas was given off when the coal was mined and the miners could not see without lamps. Attempts were made to use the phosphorescent glow from partly decayed fish, fish skins, and fungus, also to bring daylight clown into the workings by means of a series of • mirrors; •but these means of illumination proved to be impracticable."

Jan 1, 1955

By B. Amadei, F. Tonon

Rock stress measurement is cast in the more general context of the determination of boundary conditions for rock engineering. A study on the effect of elastic anisotropy on underground excavations reveals that this effect is actually controlled by the imposed boundary conditions. Applications to tunneling and to the Underground Research Laboratory (URL), Canada, exemplify a procedure for boundary condition estimation formerly developed by the authors. The procedure displayed fast convergence despite the complex geometry, and the high degree of non-linearity of the models. In the URL application, the 3-D model was able to completely reproduce the complex measured stress pattern, and the 90° rotation of the principal in situ stresses with depth. In order to reliably estimate the boundary conditions reproducing the current in situ state of stress, response measurements of the rock mass to current disturbances are necessary as input data. La mesure des contraintes in situ tombe dans le domaine général de la détermination des conditions aux limites pour les problèmes de mécanique des roches. Une étude sur le rôle de l’anisotropie élastique sur les excavations souterraines montre que ce rôle est contrôlé par les conditions aux limites qui sont imposées. L’application aux tunnels et au Laboratoire Souterrain de Recherche (URL) au Canada, nous permet de présenter une méthode de détermination des conditions aux limites. La méthode converge rapidement bien que le géométrie soit complexe et que le problème soit non-linéaire. Pour le URL, le modèle 3D est capable de reproduire la distribution des contraintes qui ont été mesurées ainsi que la rotation de 90 degrés des contraintes in situ avec la profondeur. Afin de déterminer avec précision les conditions aux limites responsables pour la distribution actuelle des contraintes, la réponse du massif rocheux doit être connue et mesurée. In der Felsentechnik sind die Spannungsmessungen in Gestein an die Bestimmung der Randbedingungen gebunden. Eine Studie legt dar, dass der Effekt elastischer Anisotropie in unterirdischen Aushoehlungen von den Randbedingungen kontrolliert ist. Eine von den Authoren entwickelte Methode zur Bestimmung der Randbedingungen wird an Beispielen im Tunnelbau und im Underground Research Laboratory (URL) in Kanada illustriert. Auch bei komplexer Geometrie und einem hohen Grad an Nicht-Linearitaet zeigt diese Methode ein schnelles Konvergenzverhalten. Ein 3D-Model und dessen 90° Drehung der lokalen Hauptspannungen mit der Tiefe, kann bei einer URL Anwendung vollstaendig reproduziert werden. Um mit dieser Methode die Randbedingungen zuverlaessig abschaetzen zu koennen, werden der gegenwaertige lokale Spannungszustand sowie die Antwort des Gesteins und die resultierenden Stoerungen als Eingabedaten benoetigt.

Jan 1, 2003

[Page Minutes 7 Discussion of L. S. Ickis' Paper 20 City Planning and Landscape Architecture for Western Coal Camps, by S. R. DeBoer 22 Discussion of Thos. Foster's Paper 26 Discussion of Safety Committee Report 30 Discussion of R. L. Hair's Paper 52 Discussion of H. I. Smith's Paper 61 Miscellaneous Discussion 62 Discussion of Thos. A. Stroup's Paper 70]

Jan 1, 1924