Search Documents

By Unal Artan

It is well known in the robotics community that the ability to determine the position of vehicles in real time is a key enabling technology required for automation, traffic management, and to ensure safety in the presence of multiple vehicles. Because of this, the introduction of global positioning systems (GPS) has had a remarkable impact on the surface mining industry, enabling real-time tracking of mobile assets, improved safety, and production optimization. Unfortunately, satellite-based GPS is not available underground. This paper reports on the preliminary results of a study to develop a robust method for globally consistent mapping of large-scale underground mine environments. We believe that this may additionally become the first step towards the development of a novel underground positioning technology. Presented are preliminary results from data collected at two underground mines using an Atlas Copco ST14 LHD machine.

Oct 1, 2009

By Jack G. Gill, Richard A. Dick

Blasting safety is a subject that cannot be overemphasized. Two years ago, a study was published describing g a series of fatal blasting accidents which took the lives of ten metal and nonmetal miners during the period of May 1973 to August 1974.1 Each accident was described, and the direct causes were delineated. In each instance, specific MESA safety regulations were violated. Four of the victims were killed by drilling into explosives; two were killed by lingering too long in the vicinity of fuse rounds; two fatalities resulted from improper guarding of shots; one blaster did not retreat far enough to avoid the blast concussion; and another used an improper tester for checking an electric blasting cap. All of these fatalities could have been avoided by adhering to the MESA blasting regulations contained in 30 CFR Part 55 (Health and Safety Standards-Metal and Nonmetallic Open-Pit Mines), Part 56 (Health and Safety Standards-Sand, Gravel and Crushed Stone Operations), and Part 57 (Health and Safety Standards-Metal and Nonmetallic Underground Mines).

Jan 11, 1977

By S. Constantinescu

The alloys mainly used for short (or segmented) chip material cutting (cast iron, porcelain, etc) are alloys of the WC-Co type; in some cases with small additions of other carbons. The same alloys but of different granulometric classes are also used for pieces exposed to wear (wire drawing, moulds) The higher performance of the WC-Co alloys in chip machining applications is accounted for by their very good heat conductivity, which is 2-3 times higher than that of fast steels. The hard-alloys producers can resort to a wide range of possibilities to achieve variation of properties of a WC-Co composition and thus they can adapt their products to the particular type of tools they may choose to manufacture. The present metallography technique allows for a correct identification and evaluation of hard sintered carbons structures. The metallography approach is an indispensable method of investigation and control in the industry.

Jan 1, 2008

The Environmental Excellence in Exploration (E3) project is driven by the recognition that the minerals industry can only maintain its long term viability by ensuring its continued access to lands to explore for, and develop, new mines. Widespread implementation of sound environmental management practices by the exploration community and improved education and understanding of that by stakeholders will help substantially in accomplishing this, and E3 is designed to meet these needs. Exploration crews are now viewed as ambassadors for the global mining community. Their performance in managing the environmental aspects of an exploration program can demonstrate a commitment on the part of the international mining sector to environmentally responsible exploration and mining. We have all observed that failure to behave responsibly can alienate local residents, encourage anti-mining NGOs and jeopardize development. As the saying goes, ?you don?t get a second chance to make a first impression?, and we want to make a favourable first impression. The E3 project is focused on creating an electronic manual, the e-manual, which will provide rapid access to the most up-to-date information on environmental management practices for minerals exploration globally. The e-manual will reflect current thinking and practices in environmental management. It will be richly illustrated with actual examples that reflect the realities of exploration. It will strive to identify the key environmental issues and concerns that apply to most exploration projects, and identify other sources of relevant information useful to field practice. It is our belief that E3, or something very like it, is central to ensuring that the industry survives the current challenges to its viability. E3 will be a cornerstone of the mining industry?s drive to sustainability simply stated, if we are not permitted to explore for mines, there will be none of them at some point in the relatively near future.

May 1, 2002

This chapter presents proportionate mortality ratios (PMRs) derived from death certificate data in the National Occupational Mortality Surveillance (NOMS) database for the years 1986 through 1993. At the time this report was prepared, 1993 was the latest year for which data were available. Industry is classified under the 1980 U.S. Bureau of the Census classification system [Bureau of the Census 1982]; cause of death, under the International Classification of Diseases, Ninth Revision (ICD-9) [World Health Organization 1977]. A PMR of 100 indicates a mortality risk for a particular industry group that is similar to that for all industry groups combined. A PMR over 100 suggests a higher risk; a PMR under 100 suggests a lower risk. PMRs are subject to many factors that affect their reliability and validity and may not be comparable across populations with very different causes of death. An elevated PMR for a specified cause of death among an occupational or industry group may indicate a relationship between a work exposure and the cause of death specified. However, there are many limitations of PMRs as a measure of risk; they are most useful for generating hypotheses about exposure-disease relationships, which can then be tested in other studies. Selected PMRs are presented separately for males and females for coal mining, metal mining, nonmetallic mineral mining and quarrying (which includes nonmetal, stone, and sand and gravel), and for oil and gas extraction. All PMRs have been adjusted for age and race. In general, PMRs are presented only if the lower 95% confidence limit exceeded 100. If a PMR in an ICD-9 subcategory was above 100, however, the PMR for the larger category into which the subcategory falls is always presented and may be less than 100. PMRs can be expected to be elevated for conditions that have a high prevalence in particular occupational groups. PMRs showed elevated values for conditions known to affect miners, such as coal workers' pneumoconiosis, pneumoconiosis due to silica, tuberculosis, chronic pulmonary heart disease, and injuries. Additional findings of interest were- • An elevated PMR for myocardial infarction among male coal miners (table 2-1); • Elevated PMRs for neurologic disease in general and anterior horn cell disease, in particular among male metal miners (table 2-3); • An elevated PMR for rheumatic heart disease in male metal miners (table 2-3); • Elevated PMRs for malignant neoplasms of the digestive organs and peritoneum and for malignant neoplasms of the colon and rectum in female nonmetal miners (table 2-6); and • Elevated PMRs for non-A, non-B hepatitis and arteriosclerotic heart disease among male oil and gas workers (table 2-7).

Jan 5, 2000

By L. C. IlsLey

Permissible blasting units are approved with the understanding that if actively marketed they will be listed as permissible so that all interested in such safety equipment may know what is available. The last detailed lint of permissible units was published as Technical Paper 4294/. All of the blasting units of that list have become obsolete or have boon modified as covered by extensions of the original approvals.

Jan 1, 1941

By L. C. IlsLey

Permissible blasting units are approved with the understanding that if actively marketed they will be listed as permissible so that all interested in such safety equipment may know what is available. The last detailed list of permissible units was published as Technical Paper 4294/. All of the blasting units of that list have become obsolete or have been modified as covered by extensions of the original approvals.

Jan 1, 1941

By H. M. Woodrooffe

In the U.S.S.R. three of the world's major-known phosphate deposits are located. These have an estimated reserve of 2,600 million short tons of contained phosphorus. The best known lies in the "Khibiny Massif', an alkalaic rock formation some 600 square miles in area with mountain peaks rising to an altitude of 3300 ft above the surrounding terrain. Location and Climate The Khibiny Massif lies north of the Arctic Circle in the Kola Penin-sula, 100 miles south southeast of Murmansk, at a latitude of 67° 30' north and a longitude of 35° 30' east. It is serviced by rail from Murmansk and Leningrad (900 rail miles south). Figure 1. The phosphate operations are centered about the two cities of Apatity and Kirovsk. The former has a population of 35,000 and is on the Leningrad¬Murmansk railway. Kirovsk, 15 miles to the east, is now a city of 85,000. The region is at the limit of the tree line with most of the ground cover typical tundra. The mean annual temperature is -4°C and, in a normal year, precipitation occurs on 240 days. Because the temperature does not exceed freezing for 300 days each year, virtually all of the precipitation is snow. The two towns are nestled between mountains and, because of the weather, extensive avalanche control systems incorporating major engineering construction have been introduced to divert snow slides away from the populated areas. General Kirovsk was first settled in 1923 and the apatite occurrences were recognized shortly after. In 1933, the first concentrator for the recovery of the mineral was completed, producing in its first year of operation 170,000 tons of concentrate. With the growth and demand for phosphate in the U.S.S.R., a second concentrator was erected at Apatity. It calve on stream in 1963. Because of the severe climate, in the early days mining was limited to 85 days per year. With the introduction of new techniques and improved mining methods, the season has been extended to 115 days.

Jan 1, 1972

By F. A. Renninger

The mineral aggregate industry is the world's largest mining and processing endeavor, yet it is graced with little of the romance or public awareness that accompanies mention of gold, silver, iron, copper, uranium, or aluminum mining efforts. Much of this reaction is undoubtedly due to the fact that the uses to which crushed stone and sand and gravel are normally put are not fully recognized or appreciated by the general public. Few individuals ever have occasion to purchase mineral aggregates for anything other than use for decorative shrubbery beds or walkways. They may, however, buy ready-mix concrete for a new patio, bituminous concrete for a new driveway, concrete blocks, or other building materials for a new room and never realize that the primary ingredients of their purchases are either direct or indirect products of the mineral aggregate industry. The average person driving past an operating crushed stone quarry or an active sand and gravel pit rarely realizes the economic impact the industry, represented by that operation, exercises on the general economy. He is not aware, nor does he really care, that elements of the modern comfortable environment to which he has grown accustomed rely to a great extent on the products of the crushed stone and sand and gravel industries Iron and steel, glass, cement, agriculture, and highway and building construction are but a few of the major industries to whom the products of the mineral aggregate industry are basic. Without these industries or without the stone, sand, and gravel basic to them, most of the major elements of our modern day civilization would be non-existent.

Jan 1, 1968

By E. Chen, M. Barati, K. Coley

The reaction between carbon and slags is of significant importance in direct smelting of iron ores, EAF slag foaming and copper slag cleaning processes. This reaction is known to occur via gaseous intermediates and it is important to have fundamental data to understand the relative importance of each reaction step. In this study, the rate of CO2dissociation on different slag surfaces is measured using an isotope exchange technique. It was found that increasing iron oxide content up to 30 wt per cent does not have a significant effect on the rate constant while increasing from this limit, increases the rate constant dramatically. Activation energy of CO2dissociation on slags of unit basicity and different iron oxide contents is in the range of 180±40 kJ/mol. It is found that rate constant dependence on oxygen potential in the slag phase is increasing with iron oxide concentration. In the case of copper making slags, the influence of copper oxide is found to increase the magnitude of apparent rate constant, while decreasing the activation energy considerably. Key words: Gas-slag reaction, CO2dissociation, copper slag, kinetics, isotope exchange

Jan 1, 2004

By R. Y. Wan

Acid ferric sulfate solution has been used for heap and dump leaching of low-grade chalcopyrite ores and is being considered as a possible lixiviant for the hydrometallurgical processing of copper sulfide concentrates. For many years, researchers have attempted to explain the leaching behavior of chalcopyrite, since the reaction rate kinetics are extremely slow and seem to be significantly influenced by the nature of the reaction product. A summary of conclusions drawn from reported literature on chalcopyrite leaching is found in the paper by Munoz, Miller, and Wadsworth(1) and more recently by Dutrizac.(2) Lowe(3) and Jones and Peters (4) attributed rate control to a surface reaction. Linge,(5) Dutrizac,(6) Bauer,(7) and researchers at the University of Utah(1,8) reported that the reaction rate is limited by transport in the chalcopyrite lattice or through the elemental sulfur reaction product layer. Munoz et al.(1) presented a model, derived from the Wagner theory of oxidation, which is based on the formation of a protective sulfur layer with rate control by electron transport through the insulating sulfur layer. By utilizing Wagner's parabolic oxidation relationships, (9) the following equation was obtained: [ ] where a is the fraction of CuFeS2 reacted at time t, pB is the molar density of CuFeS2, do is the initial diameter of the particle, e is the electronic charge, s is the total electrical conductivity of the sulfur layer, and ?G is the Gibbs free energy for the reaction:

Jan 1, 1984

Reduce the number of accidents in which large mining trucks crush objects that were not visible to the driver. Approach Improved rear view mirrors, light-bending plastic lenses, and a closed circuit TV, are combined in a rugged system that allows the driver to see almost all areas around a large raining truck. How It Works Improved mirrors, used in place of ordinary left and right rear view mirrors, give wider angle viewing. Fresnel lenses, two mounted on the front edge of the hood and another one mounted above the right front fender, show objects close to the front and right side of the truck. A rugged closed circuit TV camera mounted above the rear axle reveals objects behind the truck. See diagrams showing reduction of blind area around a 150-ton mining truck. The improved mirrors for rear viewing are approximately rectangular. The left rear view mirror has a flat reflecting surface 10 inches wide by 20 inches high. The right rear view mirror is curved to give wider viewing angles, both from left to right and up and down. This mirror is 12 inches wide by 16 inches high. Its convex reflecting surface has the same curve as the surface

Jan 1, 1979

By G. Shaw

IN recent years, most of the reconnaissance work of the Geological Survey of Canada has been mapped on a scale of 1 inch to 4 miles. Topographic base maps, commonly made from aerial photographs, were available to the geologist for such work. The advent of war curtailed aerial photography for civilian purposes, and by 1941 all areas already photographed had been geologically mapped. Nevertheless, the need for geological maps to assist post-war prospecting was so apparent, and the country to be covered is so vast, that some new method of rapid mapping had to be devised. It was felt that the need would be met if geological maps could be produced at a scale of 1 inch to 8 miles, provided they were sufficiently accurate in topographic detail to serve as guides to travel. Though in such maps there would be considerable sacrifice of geological detail, they would serve to outline, at least approximately, the major geological units, some of which might prove of sufficient interest to warrant later detailed study. It seemed that such mapping would be particularly useful in the northern regions of Canada which the work of early explorers has indicated are underlain largely by granitic rocks. These, so far as is known, are barren of mineral deposits, but within them are known to be areas or bands of 'greenstones' of the type that, in some localities, have been found to contain valuable orebodies. The problem, then, was to devise a method of mapping, particularly of such greenstone bands, that would make it possible to cover a relatively large area-say 30,000 square miles-in one season and at a cost below that of 4-mile mapping, with, of course, some sacrifice of accuracy. The problem seemed to be threefold: (a) to observe as much of the bed-rock as possible; (b) to produce a topographical map of as much of the area as possible, with particular reference to portions of geological interest; and (c) to cover as large an area as possible in a limited time, which meant faster modes of travel than have hitherto been used. The obvious answer to all three phases of the problem was the use of aircraft. If rock types could be broadly differentiated from the air, reconnaissance traverses by air would supply the answer to the first part of the problem. For topography, air photographs taken on reconnaissance flights appeared to be the answer. For the third phase of the problem, the use of aircraft was ideal.

Jan 1, 1943

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pres-sure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963

By A Nugraha, H Thanasekaran, K Tatetdagat

The Kanowna Belle gold mine is located in the Eastern Goldfields of Western Australia, approximately 18 km north-east of Kalgoorlie. The processing plant is designed to process 2 Mt/y and has the capability to treat both refractory and free milling ore from the Kanowna Belle and Kundana mining operations.The Kanowna Belle ore is refractory with the gold mineralisation occurring mostly as fine-grained inclusions in pyrite or as very fine-grained gold located in pyritic arsenic rich growth zones. The Kanowna Belle refractory process includes flotation, roasting of the flotation concentrate, and calcine leaching to extract the gold from the ore.Mineralogical analysis of feed and tailings streams from the flotation circuit have shown that the gold bearing minerals are well liberated and confirmed they are mainly associated with pyrite. Nearly 40% of the flotation circuit losses are in the -38 µm size fraction. To improve the flotation circuit recovery, the fine particle gold recovery was targeted. A Cavitation Tube column was selected for the site-based pilot test work program. This paper presents data generated from the on-site test work, and the benefits of the Cavitation Tube column to improve fine particle flotation.CITATION:Nugraha, A, Tatetdagat, K and Thanasekaran, H, 2018. Flotation circuit efficiency improvement at Northern Star Resources Limited’s Kanowna Belle gold mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 403–412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By Magnus Evertsson, Haijie Li, Erik Hulthen, Mats Lindqvist

"The static and dynamic models for autogenous (AG) and semi-autogenous (SAG) mills have been studied for decades. Though the effects of mixing soft and hard ores in a mill and their interactions are not widely investigated. To develop a general numerical model for AG/SAG mills, a dynamic model has been introduced, and its capability to simulate multi component ore breakage has been examined and compared with previous publications. The simulation results show that the dynamic model can cover a range of milling conditions and is able to simulate complex scenarios with soft and hard ores. The dynamic model discussed here could provide substantial potential for the controlling and optimization of the comminution circuits. INTRODUCTION In the last decades, efforts have been devoted to studying the comminution circuit due to their high energy consumption. The energy directly spent in minerals comminution was about 2% globally in the year 2000 (Maurice et al, 2003). As one important part of the comminution process, AG/SAG mills are widely used for primary grinding in minerals processing. AG/SAG mill models include static and dynamic models (Kojovic et al, 2012; Yu et al, 2014; Yu et al, 2017; Liu and Spencer, 2004; Salazar et al, 2009). Many static models have been well validated over the past decades, but they are all based on steady state assumptions. Even though plants experience a steady-state condition under certain circumstances, it can be inaccurate to simulate the system by static models under all circumstances (Asbjörnsson et al, 2013). The advantages of a dynamic model are apparent that it provides more information and insights both inside the mill and through interactions with other machines in terms of pebble crushers, conveyor belts, screens and so on. In many mines, the multi-component grinding is inevitable, and the ratio of hard and soft components in the mill strongly affects mills operation and performance. Bueno (Bueno et al, 2010; Bueno et al, 2013) studied the effects of blending hard and soft ores in AG/SAG mills and used them to update the JKSimMet toolkit which was a steady state plant simulation software. However, due to the complexity of the particle interactions such as multi-component breakage function, appearance function, in mill transportation, there has been no dynamic AG/SAG mill models developed yet for simulating multi-component."

Jan 1, 2018

By Angus D. Campbell

Introduction Gowganda forms part of the general Cobalt area. Its rocks and ores are very similar to those of the other parts of the area. While its total production of silver is only 4 per cent of that of the famous Cobalt silver camp, its 1928 shipments contained 42 1/2 per cent as much silver as those of Cobalt for that year. During twenty years of production, 15,000,000 ounces of silver have been shipped from Gowganda. Of this, over 8,000,000 ounces have been shipped in the past five years. The area has thus made for several years a substantial contribution to the wealth of Ontario. Its future depends to a great extent on the priee of silver, which is now, unfortunately, at a record low price. This paper is a discussion of how the Gowganda ore-shoots occur, together with some notes on the milling of the ores at the Castle-Trethewey Mines. The first part is written in the hope of stimulating further study of the silver occurrences, which may lead to further discoveries. The second part, besides being a matter of record, may be of some use to operators of small mills. The drawings in the several Figures illustrating the text are by W. D. Stroud, mine superintendent of the Castle-Trethewey Mines, the benefit of whose opinions I have had in compiling these notes.

Jan 1, 1930

By R B. Evans, M G. Townsend

In Northland, New Zealand, localised large deposits of halloysite clay have been produced by in-situ alteration of rhyolite volcanics of Pliocene or Pleistocene age, which were erupted through pre-Pliocene sedimentary strata and locally through Pleistocene basalt; and which were subsequently onlapped by further basalt flows. Alteration to clay has been a result of both hydrothermal and of meteoric processes, and decreases in intensity of alteration with increasing depth. The raw material is crushed and fractionated to produce a product of less than two micron particle size, which is of exceptional whiteness and brightness. The unique properties of the clays render them highly desirable for specialised ceramic purposes.

Jan 1, 1990

First, a classification of the various primary sources of feed materials for the production of cobalt is presented from a mineralogical point of view : sulfides, arsenides, sulfo-arsenides and oxide minerals. Each of these cate- gories will be characterized by its behaviour towards concentration methods, taking account of the presence of the associated minerals of other metals and of the nature of the gangue minerals. Then, for each category of cobalt bea- ring ores, typical flowsheets of treatment will be presented and discussed and the characteristics of the cobalt concentrates produced will be under- lined having in view their subsequent processing by pyro - and (or) hydrome- tallurgical methods.

Jan 1, 1988