Search Documents

By W. A. Cincilla

The use of resin-grouted rock anchors continues to gain popularity in underground wall mines in the United States. It is estimated that during 1985, more than 30% and as many as 35% of all roof bolts used employed sane from of resin anchor. The so-called 'combination' bolting systems, which generally utilize a resin pint-anchor, have also found increased application. This increased application is particularly true in poor ground, where more 'traditional' support measures have performed poorly. Virtually all resin bolts in use today in U.S. mines employ cartridge-type delivery systems, which in general, have produced good results under a variety of conditions. However, a host of inconsistent and sometimes uncontrollable variables may significantly alter the optimum bolt performance. These variables have been identified and are well documented in the literature (Snyder, et al., 1979; Kwitoweki and Wade, 1980; Serbcusek and Signer, 1985). The beau of Mines, Denver Research Center (DRC) conducted a major research project aimed at investigating the effects of selected aspects of installation procedures on resin-bolt performance. One objective of the project was to establish anchorage criteria for full column resin bolts installed in actual mining conditions. This piper describes the results of a particular study which focused on quantifying, through field tests, possible reductions in bolt anchorage due to installation of less-than optimum resin columns. These columns might result from losses of resin to surrounding strata, or non-compliance with recommended installation procedures. Over 1000 resin bolts having grout columns ranging from 12 inches up to 48 inches (full column) were installed and pull-tested at 13 underground test sites located in a total of 11 mines (Fig. 1). Four basic roof-rock types were included: shale, top coal, sandstone, and limestone. The majority of the bolts employed 3/4-in-diameter, 48-in-long, type 40 rebar having a minimum '~ated' yield point of 17,600 lb (8.8 tons). Actual yield strength may vary by manufacturer.

Jan 1, 1986

By J. F. Martin, J. E. Friedline, L. M. Melnick, G. E. Pellissier

A method has been developed for determining gases in steel in which the gases are extracted by vacuum fusion and analyzed by mass spectrometry. This method is especially applicable for determining small amounts of oxygen and nitrogen. The lower limit of detection for both oxygen and nitrogen is 0.0001 pct with an average deviation of about 0.0001 pct for oxygen and 0.00008 pct for nitrogen. Hydrogen analyses by this method are in good agreement with analyses by vacuum tin-fusion. A complete analysis of all gases extracted from a steel sample can be accomplished in 40 min. It has long been known that certain of the gaseous elements exert particular effects on the physical and mechanical properties of steel. With the recent advent of new experimental steelmaking practices it is now possible to obtain steels with extremely low contents of such elements as oxygen and nitrogen. Present methods for determining these two gases are of insufficient sensitivity as applied to steels made by these newer practices, and therefore a new technique was considered necessary. A review of the literature showed that the conventional vacuum-fusion method1 was the procedure most suitable for modification to obtain a sensitive method for determining the gaseous elements present in steel simultaneously. However, for trace amounts of gases it is impractical to increase the sample size because of the physical limitations of the apparatus and the increased degassing time which would be necessary. Also, when only one of the desired gases is present in trace amounts, quantitative separation by conventional vacuum fusion is almost impossible. Since small analytical mass spectrometers are now commercially available, it was decided to use this instrument in conjunction with conventional vacuum fusion for both qualitative examination and quantitative determinations of the gaseous elements in steel. This technique has already been used with success for the analysis of copper and lanthanum.2"4 APPARATUS A vacuum-fusion unit was first designed and built, Fig. 1. This unit was designed especially for the determination of small amounts of nitrogen and/or oxygen in steel since an acceptable method (vacuum tin-fusion)5 was already in use for the determination of hydrogen in steel. The vacuum system was con- structed of Pyrex glass throughout. Mercury check valves were used in place of stopcocks in the high-vacuum section of the system. Ferromagnetic samples are normally introduced into the vacuum system through a mercury lift. In case of a break in the lift, the mercury is prevented from entering the furnace by a self-locking, mercury safety check valve, Fig. 2. This check valve, developed at our laboratory, is a modified T/S ball-and-socket joint placed in the sample inlet system between the mercury and the furnace. A sudden entry of mercury or air pushes this valve into the closed position, completely blocking the top of the mercury lift. The check valve is held in the closed position by the vacuum of the apparatus. A separate entrance tube also was placed in the system, so that samples which would amalgamate with mercury, or which are nonmagnetic, could be introduced into the furnace. A slightly modified Guldner-Beach furnace is used in this system.8 The optical flat was connected to the system by a ground-glass joint to facilitate cleaning, a quartz delivery tube was substituted for Pyrex, and the crucible was used uncovered. Fusion takes place in a high-purity graphite crucible insulated by — 200-mesh high-purity graphite powder. The crucible set (crucible and funnel) is suspended in a quartz crucible. The furnace envelope and the sample inlet system are exhausted by 2 single-stage, mercury-diffusion pumps in series. The first of these is a high-speed pump, which will work only with a very low backing pressure. This pump is used to exhaust the gases from the furnace as rapidly as possible. The second mercury-diffusion pump is used as a backing pump for the first; the capacity of this pump is much lower. However, it will work efficiently against a back pressure of 3 mm of mercury. To assure positive pumping, a modified Naughton and Uhlig condenser7 is used. With the use of proper valving the second pump is also used as a circulation pump in the catalyst system.

Jan 1, 1959

By Paul H. Hunt

MANY MISUNDERSTANDINGS have arisen regarding -Al the purchase by the Government of 24,000,000 oz. of domestically produced silver annually for the next four years at a price of 64 1/2c. to the producer. Some editorials have an¬nounced rather sarcastically that be¬cause of the strong western silver bloc in Congress, the Administration is paying a bonus of approximately $22,000,000 to a few large silver produc¬ers of the West, the amount being figured on the total purchase of about 100,000,000 oz. and the difference between the Government price and the world price for silver. Actually the Government will make a profit on this purchase, due to seigniorage, of something over $60,000,000. The 96,000,000 oz. of silver, for which the producers will receive approximately $62,000,000, will be produced in association with at least $100,000,000 worth of lead, zinc, copper and gold; the greater part of this $162,000,000 worth of metal will be produced at little profit to the mining companies, as will be shown later, because of the low prices for lead, copper and zinc. This amount of money will be spent largely for labor and supplies, thus greatly relieving the national burden of unemployment. Certainly, western mining, in the purchase of this silver, is not victimizing the Federal Government.

Jan 1, 1934

By Pancho J. Garza, Keith H. Dahlen, Chris A. Labye

"Design for reconstruction of the East Flagstaff traffic interchange project located in Flagstaff, Arizona posed particular challenges. The proposed design included construction of a nearly 50-foot tall mechanically stabilized earth (MSE) wall given rightof- way constraints and soft subgrade soils. The tight right-of-way, approximately 15 feet in certain locations, adjacent to existing structures limited the number of viable remedial alternatives to provide grade separation at the proposed bridge abutment without significant settlement. Preliminary analyses indicated the existing subgrade soils - consisting primarily of relatively soft silts and clays with decomposed pumice - would settle approximately 12 to 14 inches resulting in unacceptable wall deformation. Stone columns placed via vibratory methods (vibro-replacement) consisting of circular excavations which penetrate to firm bearing soils and which are filled with crushed stone were selected to densify the existing subgrade soils. The implemented mitigation measures helped limit settlement to less than one inch and allow for successful construction of the project. The project history - including site constraints, subsurface conditions, evaluation of remedial alternatives, stone columns methodology, and effectiveness of ground improvements - will be discussed.IntroductionThis paper describes the subsurface investigation performed for the reconstruction of the Business Route 40 (B-40) (Country Club Drive) and United States (US) 89 Traffic Interchange (TI) located within the city limits of Flagstaff, Arizona. This project is currently referred to as the East Flagstaff TI. The Project Site Vicinity Map is shown below.The former B-40/US 89 TI was considered ineffective in handling the current and projected volumes of traffic which transition from northbound (NB) B-40 to US 89 (both directions), as well as from southbound (SB) US 89 to SB B-40. The intent of the project was to reconstruct the TI to better accommodate projected traffic volumes. The project eliminated the existing ramps from both NB B-40 to SB and NB US 89. The new interchange includes a Tee intersection from B-40 to US 89. In order to accommodate this alignment, the profile of US 89 was raised several feet (on nearly the same as existing horizontal alignment) to match the elevated profile of B-40. B-40 was shifted just west of its current alignment to accommodate construction of a new, wider bridge structure which spans over Industrial Drive, the Burlington Northern Santa Fe (BNSF) railway, and old Route 66. South of the new bridge, B-40 transitioned back to the existing alignment just north of the I-40/B-40 TI. Within the project limits, both US 89 and B-40 were widened to three travel lanes in each direction."

Jan 1, 2015

By A. V. Pavlov, A. V. Dubachev, K. L. Kossyrev

The purpose of the given research was to investigate the possibility of high-carbon ferrochromium refining to remove harmful impurities as a result of metal treatment by slag mixtures on the basis of the CaO-MgO-SiO2system. The final conclusions were drawn from experimental results. It was shown that the treatment of high-carbon ferrochromium by SiO2-MgO-CaO slag mixtures with additions of chromium sinter or iron-ore concentrate removes carbon, sulphur and phosphorus from the metal. A mechanism of phosphorus removal from a melt to a gas phase is proposed.

Jan 1, 2004

By N. Demirel, O. Gölbasi

Draglines are massive machines extensively utilized in opencast mines for overburden stripping. The demanding working environment induces fractures, wear and tear, and fatigue failures in dragline components and eventuates in extended maintenance, lengthy downtimes, and loss of production. The bucket is the main source of external loads on the machinery, since interactions with ground materials take place in this region. This study aims to develop a generic finite element model of the stress on an operating bucket. This entails (i) three-dimensional modelling of a dragline bucket, (ii) analytical estimation of resistive forces in the bucket movement, (iii) three-dimensional simulation of the moving bucket using finite element analysis (FEA), and (iv) sensitivity analysis to examine the effect of formation characteristics on stress variation. Simulation results imply that the drag hitch and digging teeth are the elements of the bucket that are most prone to failure. In addition, sensitivity analysis indicates that internal friction angle of the formation is the dominant parameter leading fluctuations in stress values. Changes in stress level are least influenced by formation density.

Jan 1, 2015

By C. C. Furnas

Despite the fact that a great many industrial processes depend on efficient contact between a gas stream and a bed of broken solids for their operation, the data in the literature are very meager. Several investigations3 have been undertaken, but the work has been limited in scope and application. BUREAU OF MINES PROGRAM OF RESEARCH For the past 10 years the United States Bureau of Mines has been engaged in research with the object of formulating a more or less complete quantitative theory of the workings of the iron blast furnace. Obviously, in order to do this one of the essentials is to have considerable definite information on the laws of gas flow through beds of broken solids. This report in a brief summary of the experimental work on the problem which has been done at the North Central Experiment Station. The complete report with more detailed tabulation of the data and explanations of the experimental procedure is in process of publication in the form of a bulletin.

Jan 1, 1928

By B. Suresh

Iron ore in Bellary-Hospet region is friable in nature and generates a significant amount of micro-fines (-150 µm) during mechanized mining, handling and processing. Present beneficiation practice generally employs spiral classification followed by hydrocycloning to remove slimes (-15 µm). The iron ore fines, beneficiated at JSW Steel Ltd., Karnataka generates tailing having 48-52% iron content in the form of slimes, which accounts for 50 to 55% by weight with respect to classifier overflow. The loss of iron as slime is considerably high. In this context, laboratory studies were carried out with different combination of beneficiation techniques with an objective to develop an efficient flow sheet to achieve better product grade and recovery from classifier overflow. The results revealed that de-sliming process by hydrocycloning in combination with either magnetic separation or froth flotation leads to increased iron loss in tailing. Based on investigation it is observed that forward flotation is beneficial over the reverse flotation. The experimental approach of forward flotation on classifier overflow followed by magnetic separation on flotation tailing resulted in overall product grade of 62.9% Fetotal and 70.3% yield. The tailing contains 34.6% iron, which accounts for 29.7% by weight with respect to classifier overflow.

Sep 1, 2012

By Per-Lennart Nystedt

"The Boliden Lead Kaldo Plant for the treatment of lead bearing flue-dust from the Copper Smelter and the Slag Fuming Plant has been in operation at the Ronnskar Works of Boliden Metall since the middle of 1976. At the present stage, the plant can treat lead-bearing dust of different kinds and compositions. The process allows good separation of arsenic and halogens from lead.The flue dust from the Copper Smelter and the Slag Fuming Plant is very complex and, apart from lead, also contains zinc, copper, tin, bismuth, cadmium, antimony, arsenic, sulphur, silver, chlorine and fluorine. The metallurgical process has been developed by Boliden Metall and has been tested on a pilot scale at the Foundation for Metallurgical Research (MEFOS) in Lulea, Sweden.The pelletized dust is smelted in the converter, where the heat is generated by an oil oxygen burner. The second step consists of reduction with coke. A lead bullion and slag are obtained. The slag, transported in liquid form, is treated in the Slag Fuming Plant for the recovery of zinc. The third step is the elimination of arsenic from the bullion. This is achieved by treating the lead with iron (turnings or pellets). The result is a crude lead and speiss. The lead contains silver, tin, antimony and bismuth, and is suitable for the final refining stages in normal plant equipment for refined lead.For process control, we use the rapid analysis centre, which is pneumatically and electronically linked to 'all major plant sections and allows for a quick turn-around between delivery of the sample and feedback of results. All three steps in the process are performed in the same converter.Since the starting up of the plant, the original process has been subjected to some modifications. Initial problems related to equipment, maintenance and environment have been solved step by step. Examples are quoted. Recent operating particulars are presented."

Jan 1, 1980

By N. A. Jabit

The dissolution behaviour of ilmenite in acid solutions has been studied by many researchers to improve the leaching efficiency. Most studies which utilized natural ilmenite from different origins resulted in different reactivity due to the alteration caused by the weathering process. Previous researchers have suggested that the greater reactivity shown by some ilmenite samples towards sulphuric acid may be a result of the mineral being relatively unaltered. In the present study a rotating synthetic ilmenite disc of 2.2 cm diameter was subjected to leaching studies in hydrochloric acid. The dissolution rates of iron and titanium from synthetic ilmenite were determined in hydrochloric acid solutions (4 M to 9 M) over a temperature range of 50 to 80°C. Results show that the rate of dissolution of both iron and titanium increased with the increase in acid concentration. However, the rates decreased with time and obeyed a parabolic rate law indicating the blockage of the surface by an insoluble product. The rates of dissolution of both iron and titanium were higher in the presence of SnCl2 and remained unaffected with time indicating the reductive role of SnCl2 which inhibits the formation of surface blocking solids. Application to natural ilmenite is also discussed.

Jan 1, 2014

By C. C. Clark, D. J. Benton, J. B. Seymour, L. A. Martin

"The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics and alternatives, based on information from injury reports, legacy research, stakeholder input and published literature. The results indicate that jackleg drills are involved in more groundfall accidents in underground metal mines than any other drill, and jackleg-drill-related injuries are most prevalent at the face in the course of installing initial ground support. Practical mechanized alternatives to jackleg drills for drilling and bolting under incomplete support in narrow underground openings have not yet been realized. Small, versatile mechanized bolting equipment needs to be developed to address jackleg-drill-related accidents and improve safety at mines where jackleg drills are being used. IntroductionJackleg drill is a generic name for a handheld, rotary, percussion rock drill equipped with an attached reaction leg to provide stability and thrust (Fig. 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jackleg drills are classified according to the bore size of their pneumatic pistons, which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in.) (Kurt, 1982; Clark, 2012). Jackleg drills typically weigh 46.7 kg (103 lb), but the weight can approach 54.4 kg (120 lb) after being fitted for operation with drill steel and air and water hoses (McKibbin and Clark, 2001). In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in.) diameter holes up to 1.83 m (6 ft) deep in rock."

Aug 1, 2016

By W. W. Adams

[Sales of explosives - permissible explosives5/ other high explosives, and black blasting powder - in the United States during the calendar year 1937 reached a combined total that slightly exceeded the quantity sold in 1936. A larger output was reported for permissible and other high explosives but a smaller for black powder. Production of the three classes of explosives totaled 404,744,294 pounds, more than 3 percent over 1336. The total quantity produced included 49,579,441 pounds of permissible, 288,924,253 pounds of other high ex- plosives, 36,403,950 pounds of black powder in pellet form, and 23,836,550 pounds of black powder in granular form. Sales of granular black powder declined 26 percent compared with 1936 and of pellet black powder 12 percent; gales of permissible explosives increased nearly 4 percent and of other high explosives 10 percent]

Jan 1, 1938

Mineral flotation is effective over a relatively narrow particle size range of approximately 10 µm to 150 µm. If the upper particle size limit can be increased, however, a run-of-mine ore may be coarse ground, and only the middlings are ground further to achieve required grades. This will result in significant energy savings and increased throughput. In this communication, methods of increasing the upper particle size limit will be discussed on the basis of a flotation model that can predict flotation from both hydrodynamic and surface chemical parameters. An example of increasing flotation recovery by control of a chemistry parameter is given.

Jan 1, 2014

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain a sufficient amount of rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-adsorbed elements associated with clays, and chemically bonded elements within the organic coal matrix or host mineral. Researchers at three universities collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. Leaching followed by solvent extraction was found to be the most effective to recover the REEs from coarse middlings materials collected from multiple coal basins, as indicated by recovery values exceeding 80 percent. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. IntroductionRecent studies initiated by the National Energy Technology Laboratory showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts (Ekmann, 2012). According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region consisting of areas within the states of West Virginia, Kentucky, Pennsylvania, Virginia, Alabama and Tennessee, with a total capacity of 166,495 t/h, or more than 1 Gt/y (Fiscor, 2014). If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry would become a significant producer of REE concentrates as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the production cost."

Jan 1, 2017

By J. Sanchidrián, A. Fernández, P. Segarra

The combination of chemical analysis techniques as XRF and measurement-while-drilling (MWD) technology in underground mining is a novel approach to gather comprehensive on-line information about physical and mineralogical data. In this work their integration is investigated aiming to delineate the ore/waste boundary. The input data analyzed come from a narrow vein underground mine, where the ore correspond to fluorite, and gathered in two production levels with complex mineralogical characteristics. Two approaches are followed to build a generalizable classification methodology and a site-specific model: a k-means clustering heuristic algorithm to define rock classes based on their physicochemical features, and a machine learning (ML) ensemble model trained with drilling parameters. For an imbalance class problem, a good recognition is obtained for the ore when is related to a high content of silica and for the waste. To predict the ore with low silica content it is necessary to integrate an analysis-while-drilling method to recognize the fluorite content when this mineral is embedded in different rocks. MWD can be employing for the lithologies recognition when representing different structural and mechanical properties between them.

Jan 1, 2024

By A. W. Deurbrouck

This report describes the washability characteristics of 18 coal samples taken from 11 drill hole cores from the San Juan Basin area of New Mexico and Colorado. The ash content of these coals could generally be substantially reduced by removing the heavy impurities. The coals were characteristically low in sulfur content; only one sample contained more than 1 percent sulfur after removing the sink-I.50 specific gravity material. The coals ranged in rank from subbituminous C to high volatile C; 11 of the samples were subbituminous A. Many of these core samples came from areas where very little fieldwork has been done; consequently, an outgrowth of this work has been an increase in known coal reserves of the San Juan Basin area.

Jan 1, 1972

By D. W. Gillmore

Numerous orphaned strip mines and old refuse piles scar the landscape, contributing to stream pollution and degradation of the natural environment. Field experiments to reclaim acidic surface-mined spoil and refuse banks with fly ash from bituminous coal-fired powerplants were conducted at several sites in West Virginia. Fly ash served as a neutralizing agent and soil amendment, permitting vegetation of waste lands and disposal of large quantities of ash. Reclamation of land by this method is estimated to cost about $300 per acre of leveled site, depending upon the topography of the land and quality and availability of the fly ash.

Jan 1, 1972

By V. Coffin, T. Cienski

"(Figure 1) Reagentized pulp enters into the column at about 1/4 of the distance from the top. Inside the column it meets with a downward flowing stream of water and with an upward flowing mass of air bubbles. Flotation takes place in this counter current system while at the same time fine gangue particles are washed off the froth before it reaches the overflow lip at the top of the column. The main operating features of the column flotation are as follows:a) No moving parts. Solids are kept in suspention not by an agitating action of a propeller but by settling down against the rising air bubbles.b) Wash water. Spray pipes are installed a few inches below the froth surface and deliver required volume of water. The purpose of this water is twofold:(i) it keeps in balance the flow of material through the column and(ii) it washes rising froth in the froth layer as well as removes unwanted fines attached to the bubbles at the lower flotation section. As a result the concentrate produced is of higher purity than in the conventional flotation. Column is characterized by very high up-grading. However, even temporary disruption of wash water supply results in a drastic drop of concentrate grate.c) Flow balance. (Figure 2) For the correct operation volume of the underflow (tail) is larger than that of the feed. The difference is made up by the wash water. This difference called bias is predetermined and ranges from some 4 to 15 USGPM depending on the size of the unit and process requirements."

Jan 1, 1981

LKAB operates two underground mines in Kiruna and Malmberget, Sweden. Blast furnace pellet is the main product and makes up 70 per cent of total production. The orebodies are hosted by 1910 - 1860 Ma old volcanic rocks. The host rocks and the ores were affected by the Svecokarelian orogeny for 1890 - 1860 Ma ago. The deposit belongs to the Kiruna type apatite-rich iron ore. Magnetite is the main ore mineral but haematite is the dominant ore mineral in some orebodies in the western part of the deposit. Large-scale sublevel caving is the dominant mining method. Three main haulage levels are in operation at present. The ore boundaries and quality can be detected by geophysical logging resulting in reduced waste dilution and subsequent grade reduction. The susceptibility measurements have been used in the magnetite ore since 1991 and gamma-gamma measurements in the haematite ore since 1998. The mining scale has increased during the last 20 years but diamond drilling has remained at approximately 18 000 drilling metres per year. Uncertainties in the ore constructions can lead to unexpected cost increases, ore loss and dilution. The ore boundaries are evaluated with percussion drill holes using in-hole geophysics to achieve satisfactory geological knowledge. The probes are calibrated in all currently mined orebodies. The correlation between core sample assays and measured susceptibility and gamma-gamma values is strong. The cost to determine the ore boundary by percussion drilling with in-hole geophysics is two-thirds lower, and productivity is six times higher compared to diamond drilling. The measurements are made by geotechnicians and the interpretations by a geologist. The results are transferred to a database and presented three dimensionally as holes with iron grade intervals on mine maps. The interpreted holes are used by the geologist in various ways in the geological modelling. Layout planning uses the measurements as a tool to place the drifts at the correct distance from the ore contact especially in the longitudinal sublevel caving and the production hole planning to optimise the final length of the cross-cuts and drifts for best ore recovery.

Jan 1, 2006