Search Documents

By H. Reginald Hardy

This report is Volume II of a three volume final report dealing with the microseismic monitoring of a longwall coal mine. The research presented in Volume II is concerned with the evaluation of field techniques for obtaining seismic velocity data required for computing microseismic source locations. The report describes the evaluation of a number of different field techniques and the seismic velocity data obtained at the Greenwich mine site where the micro-seismic studies, described in Volume I of the final report, were carried out. Three different methods were employed to evaluate seismic velocities, namely; surface refraction, down-hole, and transmission. In all cases the seismic sources were either located on surface (mechanical impact) or near-surface (explosive charges). It was found that a mechanical energy source could be conveniently utilized to determine shallow velocities and make bedrock-regolith interface depth determinations. For deeper velocity determinations suitable explosive charge sources Here required. In general, refraction data did not always plot in a linear manner and some subjective interpretation was necessary. The down-hole method was found to be useful for incremental vertical velocity evaluation, however, the transmission method provided the most consistent average vertical velocity data. At the Greenwich site seismic velocities were found to be anisotropic with values ranging from 9,551 to 10,739 feet per second depending on direction.

Jan 1, 1977

By Edgar Peek

Lixiviant regeneration is by definition a precondition for any hydrometallurgical process. In chloride hydrometallurgy either HCl or Cl2 has to be regenerated in order to establish an economically viable metallurgical process. One such regeneration process is widely used with steel pickling where HC1 is regenerated through the thermal decomposition of ferrous chloride in either spray roasters or fluid bed pyrohydrolyzers. This standard HC1 regeneration process deserves to be considered as a potential separation process, since thermodynamic calculations show that a fluid bed pyrohydrolyzer can function as a ferrous-nonferrous separator. Several nonferrous,metals such as zinc, lead and cadmium can be volatilized as a chloride under ferrous chloride pyrohydrolysis conditions. If such a nonferrous metal volatilization could be achieved in the case of slurry feeding of "contaminated" iron oxides, then this would increase the Fe/H2O ratio of the (process) feed and thus save on fuel per ton of iron, while yielding a marketable iron oxide product. Previous test work on synthetic materials revealed that the near-complete separation of zinc, lead and cadmium from iron oxide was possible in a pyrohydrolytic atmosphere, even if zinc was present as zinc ferrite (more than 99.5%). This investigation, which was carried out in a tube furnace at 1100 K has now been extended to treat synthetic zinc minerals and also franklinite ore. For the latter, it was found that 85% zinc volatilization could be achieved in 4 hours at 1300 K. It is postulated that complete zinc volatilization could not be attained due to the formation and/or presence of gahnite and hardystonite, which might be stable in HCl/H2O atmospheres at 1100 K. The effect of adding small amounts of calcium chloride to react with gahnite and hardystonite to give zinc chloride and both calcium aluminates and silicates is being discussed. Test work on slurry feeding of this complex ore in a recently constructed 4-inch diameter fluid bed pilot unit has been planned for the near future.

Jan 1, 1995

By R. A. Welsh

The Bureau of Mines has developed a photoelectric concentrator apparatus which is capable of collecting incremental products from the discharge of wet concentrating tables. The instrument uses photoelectric cells as sensors to differentiate between two products which have differences in color or reflectivity. The photocells provide a signal that controls a mobile splitting device that separates the products. Tests conducted on a wet table demonstrated the ability of the apparatus to separate a product containing 81.5 percent pyrite from a lower-grade product containing only 68.8 percent pyrite. The photoelectric concentrator should have a broad application for collecting concentrates with visible color or reflectivity differences from wet concentrating tables.

Jan 1, 1972

By Roy Norcross, Stephen Gos

For over 100 years Degussa has worked together with the min­ing industry not only providing quality products but also develop­ing technologies to support these products through value added goods and services. For cyanide, these technologies include leach enhancement processes such as PAL™ and Solidox™, and cyanide detoxification with peroxygen based processes such as SILOX™ and Caro's acid using our DegOX™ technology. Degussa has also made important advances in how sodium cyanide is packaged and shipped with our liquid NaCN plant joint venture with MSI, CYANCO in Winnemucca, Nevada, and our Advantage SLS™ solid to liquid cyanide delivery system. All of these innovative technologies developed to support NaCN in mining, provide value to our customers and show Degussa's commitment to Responsible Care·11.1 and dedication to product stewardship. With Responsible Care and the customer in mind, Degussa has developed Advantage CCS™ cyanide control system, which will soon be available for the North American market. Currently there are several CCS units in service installed by Degussa AG (Germany), and we are in the process of designing the next gen­eration of the CCS which should be completed by late '98. Based on our experience working with gold and silver mines all over the world, there appeared to be an opportunity to further assist our customers by providing a better more automated way to control their cyanide additions. By providing the mine with an accurate method for maintaining their desired cyanide levels in their leach circuits, we could help them avoid underdosing and the associated gold and silver losses, and overdosing the cyanide which not only wastes cyanide but may increase treatment costs as well. In the early 1990's, when we began to introduce our CCS units, there were several cyanide controllers and on-line analyzers avail­able. However, they appeared to be too complicated and not made to stand the harsh conditions inside a mill. This resulted in exces­sive downtime and poor analytical results. We also found that many units would be installed but not commissioned by the sup­plier. Based on these observations, along with filtration and con­trol problems on some existing units, Degussa decided to design its own cyanide control system based on our extensive knowledge of cyanide chemistry, using the best components available worldwide.

Jan 1, 1998

By Samuel F. Rodrigues, Clodualdo Aranas Jr., Fulvio Siciliano

The application of thermo-mechanical control processing (TMCP) in hot rolling of steels has become a common routine since the last 60 years. The understanding of the physical metallurgy behind TMCP played a major role in the early developments. Physical and numerical simulation works are performed firstly to derive the fundamental metallurgical knowledge and secondly to conceive existing TMCP practices. In this paper, a summary TMCP techniques is presented. The occurrence of dynamic transformation of ferrite in the austenite region is shown by means of synchrotron light diffraction methods. This phase transformation mechanism is taken into consideration and its effects on TMCP are proposed in an exploratory way.

Oct 1, 2019

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchange-ability, and speed, it has become even more important. In spite of the supply of other abrasive and hard materials and of ultrasonic, electrospark rued other substitute grinding, methods, world industry seams likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting roes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determined the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has affected substantial savings.]

Jan 1, 1964

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchangeability, and speed, it has become even hors, important in spite of the supply of other abrasive and hard materials and of ultrasonic, electrospspark rued other substitute grinding methods world industry seems likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting goes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determine the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has effected substantial savings.]

Jan 1, 1964

The Ministry of Economic Development has as its slogan æTogether making the differenceÆ. The Ministry is required to work in partnership with the private sector, local authorities, Maori economic entities, trade unions and community groups to transform New Zealand's industrial and economic base. The Government is seeking to achieve sustainable and balanced economic development by: being more actively involved in economic management; working in partnership with the public and private sector and with worker and business interests; focusing on adding value in industries (including primary industries) with long term potential; and bringing the tools of economic policy together in a coordinated way. The Ministry, particularly through its operating group Crown Minerals, is committed to working with industry to achieve mutual goals and to obtain continuing investment in minerals and coal exploration and mining and an active New Zealand minerals industry.

Jan 1, 2000

The increased focus on best practice environmental management has led to mining and mineral processing companies developing a variety of procedures to ensure that the environmental impacts of their operations are minimised, and that company managements are fully aware of these impacts and the policies and procedures established to ensure this process. Parallel to this, international standards for the development and implementation of environmental management systems are being promoted as necessary for companies to demonstrate their due diligence. Good environmental management systems should be built upon the systems already established within companies, and should ensure that the process of continual improvement is integral to their operation. An outline of the basic components of environmental management systems is provided, along with examples of the way various mining companies have implemented such systems. The benefits of best practice environmental management to mining companies are also considered.

Jan 1, 1995

By Paul M. Buttermore

As part of a national canvass of water use the Bureau of Mines compiled data on water requirements in the petroleum and natural gas industries for the calendar year 1962, specifically in well drilling, secondary-recovery operations, and natural gas processing plants. Total new water use in the petroleum industry of the United States, excluding refining, was 5.3 billion barrels. Secondary-recovery operations and natural gas processing plants required about 2.5 billion barrels of new water input; each of these requirements was about eight times greater than that for well drilling. Total use, including recirculated water, was 45.3 billion barrels of which 3.4 billion barrels was consumed. The greatest use of recirculated water was for natural gas processing, amounting to 38.2 billion barrels. Projections of total water use show that by 1975, 75.4 billion barrels will be used by the petroleum industry, of which 10.2 billion barrels will be new water. By 1985, the total use requirement will be 92.8 billion barrels, of which 13.1 billion barrels will be new water.

Jan 1, 1966

By Paul Meadows

This Bureau of Mines report presents operating practices and results of pressure maintenance and secondary recovery by water injection or by water injection supplemented by gas injection. Particular emphasis is placed on the results of water injection, which is the principal oil-recovery method employed in projects covered by this report. No attempt is made to study gas-injection projects or operations that are considered water-disposal projects. Also, this report does not include water-injection projects that have not been in operation long enough to evaluate results. Figure 1 is a map of north Louisiana showing the geographical locations of the projects included in this report. Most of the data used in this study were supplied by unit operators, operating companies, and the Louisiana Department of Conservation. Reservoir information and recovery data are generally those supplied by the operators, but include revisions where deemed necessary.

Jan 1, 1962

By A. A. Lavrinenko

There are discussed the possibilities of using of flotation tailings of platinum-copper-nickel sulfide ores of the Norilsk region for the preparation of backfill mixture instead of a specially produced rock and binder materials to reduce the cost of stowing operations and impact on the environment. It is shown that due to the presence in the tailings of flotation up to 10% of sulfide sulphur, which reduces the strength of the fill materials, and more than 1 g/t PGM it is necessary the preliminary extraction of the sulfides in the product for further processing that give an opportunity to reduce the losses of valuable components. It is shown that by the flotation of the current tailings it is possible to extract 91% of sulfide sulphur, 60% of palladium and 30% platinum in 17% sulfide concentrate containing 2.1 g/t palladium, and to reduce the sulphur content in the tailings up to 0.7%. Due to the easy oxidation of pyrrhotite, there is recommended fractional delivery of the collector with a total consumption 200 g/t. There are discussed results of the flotation study with an additional collector of PGM (sodium diizobutyditiophosfinate), which one show the possibility to increase extraction of platinum on 45%, as well as extraction of sulphur and palladium. For the flotation of sulfides and PGM from the current tailings there is recommended a combination of collectors for primary flotation and only butyl xanthate using in control operations. The possibility of using sludge fraction of the current tailings as a component for the preparation of the combined cementing materials after exposure of sulfides is analyzed. It is shown that the efficiency of the flotation of sulfides from this fraction can be enhanced using selective flocculants. There are discussed the advantages of implementation of completely hydrophobic butadiene-styrene copolymer in comparison with partially hydrophobic polymers. There is discussed an efficiency of the mechanochemical treatment of old tailings in turbo mill and sulphuric acid to remove oxide films from the surface of pyrrhotite before its flotation. Due to the pretreatment operation there is achieved increasing of sulphur extraction and after the introduction to the flotation circuit three control operations there is produced the fill material with sulphur content 2.5%. Keywords: tailings, copper-nickel ore, pyrrhotite, butyl xanthate, sodium diisobutyl dithiophosphinate, selective flocculation, butadiene-styrene copolymer, mechanochemical treatment

Sep 1, 2012

By James H. Owen

Because of price structure, ANFO is normally considered to be the most cost effective explosive used in quarry blasting. Results indicate that bulk smulsion can be more cost effective in applications where hole sizes range up to 6.5 inches in diameter while providing the simplicity of single product loading and storage. This can be accomplished without any fragmentation and/or movement loss usually in patterns which are about twice the size of ANFO patterns, allowing the combined drilling and blasting cost to be less when using bulk emulsions. Examples are presented supporting this concept using actual field results along with some simple calculations which take into account differences in the products such as density, matrix and detonation velocity.

Jan 1, 1998

By AIME AIME

The following report is published for the information of the members Meetings. Two meetings for the reading and discussion of papers, etc., have been held during the year 1906-namely, the Ninetieth meeting, held February 21st to 24th at Bethlehem, Pa., and the Ninety-first meeting, held July 24th to 27th in London, England, in connection with the meeting of the Iron and Steel Institute. The proceedings of these meetings, including descriptions of the entertainments and excursions connected therewith, have already been published and distributed to the members of the Institute; the Bethlehem meeting in Bi-Monthly Bulletin, No. 9, May, 1906, pp. 497 to 508, and the London meeting in Bi-Monthly Bulletin, No. 12, November, 1906, pp. 809 to 908. The proceedings of the London meeting were published separately and distributed among the many individuals and concerns whose cordial friendship and delightful hospitality contributed so largely to the success of the visits in London and environs and the excursions in England, Scotland and Germany. At the Bethlehem meeting, 37 papers and discussions were presented and the names of 198 members and guests were regis¬tered at the Institute headquarters ; this number, however, does not represent all who were present at the sessions and excur¬sions. At the London meeting, 26 papers and discussions were presented, not including 5 of the papers and discussions read before the Iron and Steel Institute at the joint session with the American Institute of Mining Engineers, which, by a mutual agreement between the Councils of the two Institutes, have been selected to be republished in the Bi-Monthly Bulletin and Transactions of the Institute. The number of members and guests of the two Institutes registered at the London headquarters was 908, and of this number 131 were from America. This list does not include the names of all who

Mar 1, 1907

By Andréa Lagacé

"The milling of sulphide ores inherently generates “thiosalts”, a series of partially oxidized sulphur oxyanions (S2O3 2-, S3O6 2-, S4O6 2- etc.), which make control of effluent treatment systems difficult because their natural oxidation produces acid with the potential to lower the pH within the treatment system and/or receiving environment.At the Xstrata Copper Kidd Metallurgical Site, thiosalt oxidation in the Tailings Management Area continues after buffer storage Ponds A and C where lime is added to precipitate metals and elevate the pH to within the required range for discharge. If the additional acidity generated during the continued process of thiosalt oxidation is not neutralized there is a risk that the final effluent will be non-compliant with regulated standards.To mitigate this risk, in 2007 a full scale pilot trial was conducted with hydrogen peroxide in order to force the complete oxidation of thiosalts prior to the lime treatment stations. This method of chemical oxidation had been shown to be effective at Xstrata Zinc’s Brunswick Mine. The pilot results indicated that a maximum of 50% of the stoichiometric quantity of hydrogen peroxide is required to reduce the thiosalt concentration in the No. 2 thickener overflow stream (feed to buffer storage Ponds A and C) to less than detection (10 mg/L); however, treatment was only effective in the presence of a 20 mg/L iron (Fe) catalyst. Since the hydrogen peroxide addition point at the No. 2 tailings thickener overflow typically contains <1 mg/L total Fe, a second reagent, ferric sulphate, was used to increase the total Fe concentration to the required level. This paper describes the set-up and results of the pilot trial which were used in the design of the full-scale plant.INTRODUCTIONTailings Management Area OverviewXstrata Copper’s Kidd Metallurgical Site, located in Timmins, Ontario, is an integrated metal refining facility producing copper, zinc, cadmium, indium, liquid sulfur dioxide, and sulfuric acid from third party custom feeds, and mineral concentrates recovered from its 7,800 tonne per day mill."

Jan 1, 2010

By G B. Ebsworth, J Krokowski de Vickerod

Several drilling programs at Maldon have produced 7790 core samples, which were assayed for gold, with 2825 of the samples assayed for nine other metallic elements. There is a lack of correlation between gold and all other elements. The situation, however, changes dramatically when sorted according to the abundance of arsenic. In the populations where As &gt;200 ppm, there are strong, positive correlations between gold and several elements. There is also a strong positive correlation of Au with the weighted sums and products of all elements with the elemental averages as a weighting factor, and Bi*Sb and Bi*As elemental products. In these populations, there is also a strong positive correlation between the logarithms of Au and logarithms of each element, as well as the elemental sums and products described above. The correlation coefficients increase with higher As cut-off values.All elemental distributions but especially gold show a high-nugget effect and display high skewness and dispersion, low kurtosis, and common outliers. The distributions of their logarithms are several magnitudes less scattered and without outliers. Thus, the logarithmical distribution correlations are best for practical use.Correlation coefficients were T-tested and are statistically significant. The elemental correlations, particularly those of logarithmic values of weighted sums and Bi, could be used as a gold path finding tool at Maldon. After a preliminary assay for gold and arsenic, only samples with As &gt; 200 ppm should be assayed for other elements. Higher values of gold-correlated elements or elemental ratios, in samples with low gold grades, may increase confidence that gold is under reporting due to its highly nuggetty nature.CITATION:Krokowski de Vickerod, J and Ebsworth, G B, 2012. Correlation as a gold path finding tool at Maldon, Victoria, in Proceedings Narrow Vein Mining 2012 , pp 131-144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

Study on Desulfurisation and Deashing for Medium-High Sulfur Coal Using Shaking Table As important coal resources, medium- high sulfur accounts for a significant part of the coal reserve in China. The environmental regulations and fuel standard requires sulfur and ash to be removed before it is used, so as to save energy and decrease the emission. Therefore, the effective desulfurisation and deashing technologies are urgent needed. However, due to the local characteristics of the coal, specific technology with optimum operation parameters is required to develop for different local&nbsp;coal. Qinglong is a district of Guizhou Province, which has large medium to high sulfur contained coal reserve. In this paper, medium-high sulfur coal is sampled from Qinglong, Guizhou province. Some basic characteristics such as the mineralogical composition of the coal rock, the monomer existing state and the granulometric composition are determined by X-ray diffraction quantitative analysis and polarisation microscope analysis respectively. Adopting the classified feed method, shaking table tests show that the feed pulp concentration is 20 per cent, the stroke is 13mm, the frequency of the stroke is 380 per min, the cross slope is 3¦ and the volume of wash water is 5.2 L per min. Under such condition, aggregate processed coal yield is 72.87 per cent and sulfur content decrease to 1.31 per&nbsp;cent With shaking table technology of &apos;First stage rough and intermediate further fine benefication&apos;, the yield of concentrate coal increased from 72.87 per cent to 81.21 per cent, while the sulfur content reduced to 1.35 per cent.

Sep 13, 2010

By S. J. Broderick

[Xuge d-mp heap co:lt:.ini9: tilcu?:na3s of tons of cad ~eP~se 2r3 a failiar sight in coal-mininc regior@:. T5ey reprecei~t considergole economic 1083, are very l.u.,si~hC,ly, ?:ld t?ke un m-lch vaL-x3le qace. Cor.sequentl;r thelr remcval i~ geatlyr dezir36, ax2 my ret-sn t?-at c,m be obtained would be er;pecic.llj .a~elconre&apos; t.7 the cod ir.S..r; kry. T?.e vaste rk.t~ri..tl conpl-ises large pieces of slr.t.e, hi~h-2s&apos;. bore c~al., luqs cf cle:., ,ad finer refuse conin,= fro3 the vrtskery, Tilt 1:zshcr:r refilsn contnins sone yood coal. Rig coal and the &apos;better p~lcs of bore ere the zat~rla2.s ~15:;~itiered in this in- vest ig:?.tion. 7% Il~avter frnctions of the w~~sherjr ref;lw aizd tts large 2ieces of slcte ?,".:I rgck contilin 1it:lei ccai-i-bcna.c~o~s caterial ad are vir- tu<dly worthiess nc, rz:. ::atcrin!. for .*=irin,= zct,iv?*teb cCvb~n. 13 the 3irniingh.m district, i13br.12, a-c.ju",P p?rcccn",f the c3sl r?.ir?ed is washed, ,md in tkis c?i.;trict nlz:~c rcfilce ecc;:?:lletcs ~t the r%tg of 1 to 2 million .! tons 2 yew.]

Jan 1, 1941

By N. D. L. Burger

An effective prototype face support system to minimize rockfalls in rockfall-prone mines was developed and patented during a project sponsored by the Mine Health and Safety Council (MHSC). An experimental development model (XDM) roof support unit was developed and evaluated. Mines with rockfall problems in the face areas can use the roof support system to reduce fatalities and injuries in the face area of stopes. The roof support system consists of two similar support units connected to each other via two crank mechanisms. Each unit consists of a headboard supported by a ?wishbone? structure (top and bottom leg). In the first design a threaded bar with struts similar to a scissors jack keeps the legs apart. (In the final version that was field trialed, the threaded bar mechanism was replaced with a hydraulic cylinder). All the components are manufactured from steel. To move the system forward the first support unit is collapsed, the second remaining in the loaded position. The first unit then hangs from the second unit to which it is connected. The first collapsed unit is then manually cranked forward and prestressed. If the required position is still not achieved, the other unit is released and moved forward. The specification for the system was determined and presented at a workshop with industry participants. Different concepts were developed and evaluated against the system specifications. A technology demonstrator was then developed and tested on surface. The technology demonstrator development process included detail design, building and testing of components and subsystems, design reviews and the building and commissioning of the technology demonstrator. The testing of the technology demonstrator was done in a 500-ton hydraulic press, in a mock-up stope and underground. A risk analysis, in which technical, logistical and economic aspects were assessed, was done to determine the critical areas of the system. During the next phase of the project working prototypes were developed for underground tests and evaluation. This process indicated that it was necessary to adjust the system specifications and a redesign was called for. In an iterative process test units were built for purposes of evaluation, specification verification and field trialing. After the successful conclusion of the trials the equipping of a complete production stope started for purposes of integrating the system into the current mining process.

Jan 1, 2008

By J. R. Ross

Recovery of uranium from slightly alkaline mine water, available in the Ambrosia Lake district of New Mexico, was studied using countercurrent ion exchange columns developed by the Bureau of Mines. Approximately 5 million gallons of mine water containing 9 to 12 ppm U308 was treated by ion exchange using a 14-inch-diameter absorption column composed of five or six compartments each 4 feet deep. Uranium recoveries averaged in excess of 98 percent at solution flows ranging from 15 to 25 gallons per square foot per minute and resin loadings up to 3.6 pounds of U.08 per cubic foot. In subsequent tests, loaded resin was continuously eluted in a countercurrent elution column with a diameter of 4 inches and containing a bed of resin 9 feet deep. The resin was eluted to a residual loading of less than 0.06 pound of U305 per cubic foot, at a resin-retention time of 224 minutes, using only 1.9 volumes of 1.1 M NaCl-0.05 M NaHCO3 solution per volume of resin. Compared with existing ion exchange practices for recovering uranium from mine waters in the Ambrosia Lake district of New Mexico, use of these improved ion exchange contactors would reduce ion exchange resin requirements at least 70 percent and allow further substantial reductions in capital and operating costs.

Jan 1, 1971