Search Documents

By Oliver Bowles

Limestone, including dolomite, is the most widely used of all rocks - nearly 300 million tons annually in the United States alone. It occurs in some form in every State and is produced in thousands of localities. Because of its attractiveness, substantiality, and durability it is employed extensively as a building stone. In crushed and broken form it is used for concrete aggregate and railroad ballast and in highway construction, metallurgy, agriculture, and a host of chemical and industrial processes. This paper proposes to furnish general information on the origin and occurrence of limestone and dolomite, chief production centers, major uses, and methods of quarrying and preparing stone for market. Footnote references will guide the reader to sources of more complete information.

Jan 1, 1956

By H. C. Boydell

Introduction Situated in the district of South Lorrain, some 16 miles southeast of Cobalt, Ontario, and reached from that centre either by branch line of the T. & N. O. railway or by what, for a mining camp, is a reasonably good road, the Keeley mine, owned by the Keeley Silver Mines,' Ltd., has had its history recorded by C. W. Knight (1). Silver was first discovered in South Lorrain, in Woods' vein, on Keeley property, in 1907, and the Keeley mine has been described by Knight (2) and Bell (3). The total production to February 28th, 1930, has been 10,760,107 ounces of silver and 1,285. 434 pounds (weight) of cobalt.

Jan 1, 1931

By Burton J. Thamer

Radon emanation coefficients of 0.02 to 0.55 were measured at moisture contents ranging from dry to saturation in eighteen different ores. The emanation coefficients rose from a minimum when dry to a plateau usually starting at 5-20 percent of saturation. A model, using measured pore-size distributions, suggested that the radium mineralization may be confined to annular layers about 0.02 micrometers thick around pores. Radon's diffusion coefficient was determined as a function of moisture. The techniques involved comparing a disc's exhalation as a function of time whether or not the disc had a distributed source. The model was free of approximations and included the effects of porosity and adsorption. An increase of diffusion coefficient with moisture for one or two ores was explained in terms of a model's equation for the diffusion coefficient in terms of both volume and surface diffusion. Radon's adsorption coefficient was determined on a uranium ore.

Jan 1, 1981

By K. van Warmerdam, M. Pearson, C. Kember, D. McMullen, M. Thayer, C. Ugarenko

In July 2012, Hatch Ltd. and Air Products & Chemicals Inc. completed construction and commissioning of a 4000 tpd O2 cryogenic air separation unit (ASU) for Barrick Gold’s Pueblo Viejo Project located in central Dominican Republic. The ASU produces high pressure gaseous oxygen, which is used for the oxidation of refractory sulphide ore within the pressure oxidation (POX) circuit. As a result of the project’s remote location and tropical climate, many challenges were faced over the course of construction, commissioning and start-up of the ASU. These challenges included adequate preservation of equipment due to dusty and humid site conditions, final assembly and erection of the cryogenic distillation columns on site, limited spare parts inventory/availability, and an unfinished power source for plant commissioning. This paper discusses the steps taken by Hatch and Air Products to successfully design, construct, commission and start up the largest stand-alone ASU plant for a POX application in the metallurgical industry.

Jan 1, 2014

By L. M. Yokum

Tremendous strides have been made in front end loaders in the last fifteen years. Fifteen years ago a 2; cubic yard front end loader was the largest standard machine you could purchase. Today there are two commercially available 15 yard front end loaders and many 10 yard front end loaders. The estimated total worldwide market for all front end loaders over one cubic yard has increased to over 30,000 units yearly. The trend for front end loaders, in general, and for the mining market, in particular, is to larger and larger loaders. Today there are 18 cubic yard and a 24 cubic yard front end loader in prototype form. It is not inconceivable that within another fifteen years that there will be front end loaders in the 50 cubic yard class with design features quite different from today's. These larger loaders are being designed at the demand of the mining industry and the design criteria are being directed at this market area. The costs of these larger loaders will be greater per unit of capacity, and it is the intent of the various manufacturers that they will be more reliable, be easier to service, give greater availability, live longer, and cost less to maintain, than previous loaders. It is also the intent of the manufacturers to compete directly with the large mining shovel as the front end loaders become appropriately larger and more reliable. There has been some trend in this direction in the past with smaller shovels and loaders. In Figure No. 1 are data for U.S. production of front end loaders (5-6 cubic yard class and 10 cubic yard class) and U.S. production of cable operation, crawler mounted power shovels, draglines and cranes (1; to 5 cubic yard class) for the years 1965 and 1970. (Source: Bureau of Census, U.S. Department of Commerce.)

Jan 1, 1972

By WALTER CARROLL

Between cross currents of economic factors and international expediencies the iron and steel industry in 1948 made an outstanding contribution to the general economic picture. Were it not for an unfortunate episode during the month of April involving a temporary shortage of coal, 1948 would have been an all-time record year in output. Exceeded in no previous peacetime year, the production of iron and steel in 1948 totaled some 88,500,000 tons. That it was a worthwhile effort of no small magnitude is evidenced by the fact that in three and one half years following the war, this nation has produced as much steel as in the five years preceding the war. This figure of 88,500,000 tons is 68 per cent greater than that for 1939.

Jan 1, 1949

By J. R. Goode

"The Las Cristinas deposit contains about 10.2 million ounces of gold at a grade of 1.3 g/t. The deposit comprises a layer of fully oxidized saprolite (SAPO), a layer of sulphide-enriched saprolite (SAPS), carbonate leached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same level in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper it having been leached and deposited in the SAPS zone.A previous owner started investigation of the Las Cristinas deposit in Venezuela in 1991. Over the next seven years, 1174 holes with a total length of 159 km were drilled, extensive metallurgical testwork, including pilot plant operations, were conducted and feasibility studies were completed. Construction was started in 1997 and again in 1999 but was suspended.Crystallex has been producing gold in Venezuela since the early 1990’s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana, (CVG), to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in early 2003 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and Professor A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-in-leach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the recent testwork, discusses the proposed plant design, and presents economic data."

Jan 1, 2004

By M. Mathey

The application of the Monte Carlo technique to production planning and everyday economic decisionmaking in mine production management is demonstrated. The logic is detailed using an example of underground production with continuous miners (CMs) and truck haulage. It is argued that availability of equipment and personnel are the predominant variables influencing mine output and productivity and that those availabilities may be well represented by binomial probability distributions. The probabilistic model is implemented in a standard Excel® spreadsheet with Palisade’s @Risk add-on to facilitate simulations. Starting from model calibration against data obtained from a mine’s annual reports, some general interdependencies of availability, utilization, productivity, and costs of production processes are outlined. Finally, several possible options and their consequences as regards production improvements are explored.

Dec 13, 2022

By B. P. Watson

The first crush pillars on the Bushveld platinum mines were introduced at Union Section in 1978. Before the introduction of crush pillars, serious problems were experienced when stoping advanced to a point 30 m to 40 m on both sides of the centre gully. At least three to four stopes were collapsing per month. The introduction of the pillars stopped the stope collapses in the mining area where they were introduced. The residual stresses of these pillars were never measured; however, the successful elimination of the ?back-break? problem suggests that the original pillars had a residual strength of at least 8 MPa. Apart from back analyses, very little work has been done to determine the residual strength of crush pillars and only very recently have any measurements been made. The lack of knowledge in this field has resulted in pillars being designed based on experience. Concerns about stope collapses, similar to the Coalbrook disaster, have led to larger pillars being cut in more recent times. If such pillars were cut in brittle quartzites they would always fail violently but the ductile nature of the Merensky Reef generally allows large pillars to fail without bursting. Occasionally, however, one would burst in a working area. Increased incidence of bursting has been reported on some mines at deeper levels but most of these bursts occur in the back areas. Nevertheless, the incidence of bursting increases the risk of falls of ground in already dangerous areas, and the larger pillars decrease the extraction ratio. This paper describes the evaluation of stress measurements conducted in two boreholes over a crush pillar with dimensions 2.5 m x4.0 m, and a height of 1.2 m. Boussinesq equations for vertical and shear stress were used to analyse the original measurements and provide a stress profile across the pillar as well as the residual strength of the pillar. The results showed an unexpectedly high peak stress of 280 MPa at the centre of the pillar and a residual strength of 48 MPa. The reason for the high residual strength is suspected to be the result of the stiff environment under which the pillar failed and the small height of the siding on the up-dip edge of the pillar. More measurements should be conducted on several mines to establish a range of residual strengths for narrow crush pillars.

Jan 1, 2008

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, A. S. Kabir, R. Petrov

The recrystallization and texture evolution of AZ31 sheets obtained through two stages was investigated at different stages of post-rolling annealing. The specimens were rolled at the temperature of 100? and at a fast speed of 1000m/min and low speed of 15m/min with a reduction of 30% in one pass. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2015

By J. Huisman

With the introduction of ever-stricter environmental operating guidelines, capital expenditure restrictions and operational budget cutbacks, the biological method of SO2 removal becomes more and more attractive. Biological treatment of dilute flue gases is a more cost effective technology in comparison to conventional sodium hydroxide scrubbing. Although the investment costs for sodium hydroxide scrubbing is lower, the operational costs are significantly higher. In addition, the end product of the biological installation is sulfur instead of sodium sulfate; and no further wastewater treatment of the bleed from the biological installation is required since heavy metals are removed simultaneously. Another option for the treatment of SO2 containing gas at a sulfuric acid plant is the production of extra sulfuric acid of the discharged SO2 by applying an additional converter. Comparing biological treatment with this option shows much lower investment costs for the biological installation. Sulfur is produced which can be converted to sulfuric acid, so the bio-route will be more cost-effective than an additional converter. In principle, the biotechnological gas cleaning system is an integration of an absorber with a wastewater treatment facility. In the absorber, the SO2 containing gas is brought into contact with the washing water. The effluent absorber liquid contains a mixture of sulfite and sulfate that is converted into elemental sulfur. This conversion takes place in an integrated system; first, the sulfite/sulfate mixture is converted anaerobically into sulfide; secondly, the sulfide is converted aerobically into elemental sulfur. Subsequently the sulfur is separated and the water is returned to the absorber. Due to the buffer capacity of the washing water, removal efficiencies over 98% are possible. In addition to SO2 removal, it is possible to convert for example other bleeds streams such as scrubber acid or weak acid to sulfur in the same SO2 installation. Recent evaluations concluded that biological desulphurization of flue gases is not only economically attractive in comparison to convention sodium hydroxide scrubbing but also in comparison to gypsum producing systems and even seawater scrubbers. This paper describes the technological and economical viability of biological flue gas desulphurization.

Jan 1, 2005

By J. P. Bennett

The Bureau of Mines investigated the dimensional changes of ceramic materials exposed to acid environments to evaluate construction materials for emerging technology in chemical and metallurgical processes. Six commercial ceramic materials (two red shale, two fireclay, one silica, and one silicon carbide (SiC» were exposed to H20, 20 and 30 wt pct HCl, 40 and 60 wt pct HN03, and 10 and 50 wt pct H2S04 at temperatures from 50° to 90° C for 300 days. Linear expansions ranged from a low of -0.02 pct for the silica to a high of 0.45 pct for the red shale. A general ranking of the volume expansion of the materials tested, (from high to low), is as follows: high-porosity red shale A and fireclay B » low-porosity red shale B and fireclay A > silicon carbide and silica. A general ranking (largest to smallest) of the effect of exposure environments is HCl > H2S04, HN03 > H20. An autoclave test method was evaluated. Data obtained from 8-to 24-h exposures were compared with data obtained from the 300-day exposures. The relative expansion trends were similar, indicating that this method could be used as an accelerated test.

Jan 1, 1988

By Rudrajit Mitra, Erik Hulthén, TOBIAS HARTMANN, ELISABETH CLAUSEN, Aarti Sörensen

There has been an ongoing debate on how to transform engineering education to better prepare students for today`s professional world that is characterized by increasingly complex problems and challenges that engineers are tasked with upon entering the industry. Within the conceive–design–implement–operate (CDIO) framework, entrepreneurship education presents a valuable pedagogical approach to foster the necessary skills of the students through integrated, hands-on, active learning experiences. While numerous publications have addressed possibilities of how experiential, problem-based, project-based and active learning can be integrated into engineering curriculum, there has been hardly any attention on mining engineering with respect to adopting this approach. This paper will address the possibilities of integrating entrepreneurship education into mining engineering programs in particular. This paper will enhance and foster discussion among academics from mining engineering on how to integrate elements of entrepreneurship education on a course, program and departmental level to infuse value creation experiences across the curriculum.

May 25, 2022

By G. S. Hill

A large amount of the stereological error associated with liberation studies can he eliminated by assessing areas instead of linear intercepts. The presentation of a simple geometrical model as a stereological 'worst case' allows calculation of the worst possible grade/recovery curve for a given assemblage of areas. The true results are expected to lie in the window between this worst case and the hest possible case, represented by uncorrected data. The width of this window typically corresponds to an error margin of about 5% grade at a given recovery. An indication of where the data lies within the range of possible grade/recovery results may he obtained from a qualitative analysis of the locked section complexity. Assemblages consisting of texturally complex locked sections (ie. containing many mineral nuclei) are likely to exhibit minimal stereological bias and therefore will tend to lie close to the uncorrected side of the grade/recovery window.

Jan 11, 2011

As 1979 drew to a close, it was obvious that China would have another good year with output of most industrial products at 3-9% above levels attained in 1978. Most increases were registered on the basis of maximum utilization of existing capacities and nationalization of procedures and methods. There were also distinct improvements in the quality and variety of products. Coal output probably surpassed the 650-Mt level in 1979. Steel output was expected to reach the 35-Mt level, an increase of nearly 10% over 1978. Based on the vast amount of housing and road and project construction, cement production more than likely surpassed 70 Mt. The nonferrous base metal industries improved somewhat in 1978, but actual output levels in recent years may have been a little higher than previously estimated by the outside world. Stagnate world demand slowed growth in the "export metals" sector. Minerals like magnesite and talc were produced at tonnages much larger than previously thought, with gold also falling into this category. Sulfur and pyrite production are still short, although a big pyrite mine was being brought into production. Barite out-put was reportedly up and fluorspar output held its own. Westerners generally concede that difficulties in transportation and power supply are holding back mineral production. Throughout 1979, basic construction continued on the majority of projects started by the Chinese and those few foreign projects contracted before the adjustment of industrial priorities. Foreign Ventures Perspective The foreign connection looms large in China's plan for modernization. In effect, it is an extension of what China wants to do in terms of "walking on two legs"-that is, develop what can be done locally to the fullest extent, then rely on international technology to move into the bigger and more complicated projects. Foreign projects are designed to complement domestic projects rather than replace them. Many foreign projects were started or continued by the Chinese in 1979. Building the necessary infrastructure for the projects is usually a Chinese endeavor and requires Chinese technicians and money. In areas with a strong economic base, this activity proceeds without foreign aid. In other areas, added funds are requested. Foreign funds can come in many forms-equipment technology, low interest loans, equity capital, advance-of-funds on the basis of future delivery in kind, and joint venture money. The Chinese are exploring all these avenues, with the strategy of minimizing foreign exchange needs for individual projects. They feel very uncomfortable with high interest rates, even though interest can be treated as operating ex¬pense rather than capital expense. Then there's the question of rights. Will Chinese sovereignty be affected? Can foreigners own land, in addition

Jan 3, 1980

By Konrad Krimpelstätter

The need for more effective and flexible roll-gap lubrication technologies in hot and cold rolling mills is steadily increasing due to ever-greater requirements placed on the rolling process and the final products. In particular, the rolling of high-strength steels poses enormous demands for both the rolling mill and the coolant/lubricant to be used. The presented paper focuses on two innovative technologies for highly efficient roll-gap lubrication for hot and cold rolling, which were developed utilizing extensive knowledge and expertise about the tribological interactions in the roll-gap. The advanced work-roll lubrication package (A-WRL) for hot rolling and ESP mills is using specially designed mixer-nozzle units to mix the water/oil emulsion very close to the nozzles to minimize the risk for contamination and clogging. The nozzles are quickly exchangeable and are optimized to ensure uniform lubricant distribution, high plateout efficiency and minimum oil consumption. This eco-friendly solution does not require any chemical additives or cleaning agents and significantly reduces electrical energy consumption and work-roll wear. The roll cooling system on mill entry and exit side remains switched-on, which is of vital importance especially for highperformance hot strip mills. Minimum Quantity Lubrication MQL® represents a new generation of roll-gap lubrication technologies for cold rolling, which applies minimum amounts of pure rolling oil finely atomized with pressurized air directly onto the work roll surface. This allows controlling the oil film thickness depending on actual process and product parameters, providing increased lubrication flexibility, significant improvement of strip surface cleanliness through reduction of strip wear. MQL® was successfully installed and tested on two industrial tandem cold rolling mills in Europe. Advanced WRL and MQL® represent Primetals’ latest technologies that feature a robust and reliable system comprising standardized interfaces and flexible communication options. Both packages can easily be integrated into existing or new hot strip mills, ESP lines or cold mills.

Aug 17, 2017

By Thomas D. Kaufmann

Introduction Mining has always been sensitive to the fluctuating income of downstream customer industries. The industry is now becoming more vulnerable to booms and busts as economic pulsations increase and demand for mining products shows little or no long-term growth. As the general economy has become more cyclical in the last decade, the capital-intensive primary industries have become more aware that timing as well as preparation of survival plans are vital in investment decisions. Strangely, however, some of us have not yet included the business cycle in our feasibility studies. Cyclic prices and volumes and fluctuations in profits and cash flows do not fit our linear models. The increased cyclical nature of our economy is recent and poorly understood. Forecasting peaks and troughs is still more an art than a science. Nevertheless, avoiding business cycle parameters can lead to error in value estimation and contingency planning of new projects. Metal and Mineral Industries More than half the iron and steel, aluminum, copper, lead, zinc, manganese, tin, nickel, molybdenum, cobalt, and chrome that we mine, smelt, upgrade, and recycle goes to construction, transportation, capital goods, and consumer durable industries. All are cyclical. Their products are consumed slowly, so replacement can be postponed in recessions. Purchases of such goods are usually financed by debt, and their customers are sensitive to highly cyclical changes in interest rates. During prosperous periods, people tend to buy capital goods despite high interest rates. Upstream industries also tend to be whipsawed by inventory cycles. With high interest rates and good transportation, downstream fabricators can lighten their inventories during recessions. They know that upstream suppliers can deliver supplies and raw materials immediately, And, with the advent of electronic accounting, the fabricator with timely inventory information can afford to hold fewer contingency stocks. Likewise, when recovery returns, inventories surge back through industry pipelines, accelerating demands on primary supplies. The price elasticity of most primary products is low. Their share of the value of finished products of the industries they supply is generally small. The 60 kg (130 lb) of aluminum in a car is vital. But whether it costs $80 or $130 will not visibly influence the demand for an automobile. With low elasticities of demand, the primary producer is hit with decreases (or increases) in prices and in sales volume, during recessions as well as recoveries.

Jan 6, 1984

By P. A. Plunkert, D. E. Morse, L. McCartan, J. F. Papp

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several stages —basic (mining), intermediate processing, manufacturing of finished goods and construction. The real GDP increased by 3.5 percent from 2004 to 2005. The nominal GDP was $12.5 trillion at the end of 2005. Housing starts were up by more than 5 percent for the year, and the unemployment rate decreased to 5.1 percent in 2005 from 5.5 percent in 2004. The prime interest rate increased from 5.25 percent at the beginning of the year to 7.25 percent at the end of the year. The value of minerals mined in the United States in 2005 rose significantly because of increased unit prices for some metals —particularly molybdenum — and significantly increased production for some industrial minerals, mainly cement, construction sand and gravel, and crushed stone.

Jan 1, 2006

By Wang Xuewen, Bao Qingbao, Xie Jiacheng, Yan Zewen

This study puts forward a virtual memory cutting method based on the prediction of AFC shape. The integrated key technologies include the generation of virtual teaching cutting curve, the height adjustment strategy of front and rear drum, cutting height adjustment strategy, the reciprocating cycle of cutting technology and so on. Through the two algorithms, SVM and ELM, the form of the next working cycle can be obtained by rolling prediction using the form information of AFC in the first several circulations. Based on the obtained dynamic fluctuation of the form in the vertical and horizontal working faces, the position and cutting information of the shearer during its operation can be controlled and predicted in advance, the memory cutting template can be adjusted and modified in time. Employing this method, the more stable, accurate and timely memory cutting of the shearer under the uneven coal seam could be realized.

Aug 16, 2021

By Jeremy Butkovich

Dynamic soil-structure interaction (DSSI) analyses are becoming more common in bridge designs, especially in seismically active areas. Because of its proximity to two active fault zones, the Evergreen Point west approach bridge replacement will be base isolated, and will be designed using DSSI. The project team completed two independent bridge designs to satisfy peer review requirements. The designs required substantial characterization of the soil dynamic behavior using both laboratory and in-situ testing. The analyses made use of earthquake time histories spectrally matched to conditional mean spectra. This led to reduced, and more realistic seismic demands on the structure, compared to conventional uniform hazard spectrum matching. The bridge analyses suggest that the preliminary bridge design is relatively conservative. This will allow the design team to potentially reduce shaft/column diameters and reinforcement. The design team estimates that the dynamic analysis design could represent a net savings of around $60 to $90 million compared to a conventional design.