Search Documents

By T. Burchett, F. Stanley, K. McGough, G. Luttrell

The vast majority of U.S. coal preparation plants utilize screen-bowl centrifuges to dewater their fine clean coal products. In light of this popularity, researchers at Virginia Tech have engaged in a variety of laboratory and industrial field test programs to develop technological enhancements that have the potential to further improve the performance of this important solid-liquid separation process. These enhancements, which include simple design modifications and new reagent packages, have been shown to significantly improve solids recovery and reduce product moisture in several experimental trials.

Jan 1, 2006

By Shoukun Wei, Cong Wang, Lin Cheng, Zhiyu Qiao, Jingkui Liang, Weidong Zhuang

"The subsolidus phase relations in the Sm2O3-CeO2-CuO ternary system sintered at 1000°C in air have been investigated by X-ray powder diffraction. The system can be divided into two ternary phase regions and three binary phase regions. Solid solution Sm2-xCexCuO4-y is the only ternary phase in the system. The maximum solid solubility was confirmed to be x = 0.2. The crystal structure, oxygen content and superconductivity of the solid solution Sm2-xCexCuO4-y have been investigated.I. INTRODUCTIONAfter the first discovery of the superconducting ceramic system La-Ba -Cu-O[l] with Tc = 30 to 40K, other families of cuprate-based ceramics have been synthesized with higher critical temperature. These oxides include the R-Ba-Cu-O (R: rare earth) systems (Tc=90K or so)[2,3], the Pb-Sr-(R,Ca)-Cu-O systems (T c = 50 to 100K), the Bi-Sr-Ca-Cu-O systems (Tc=80 to 105K)[4], the T1-Ba-Ca-Cu-O systems (Tc=85 to 125K)[5], the Hg-Ba-Ca-Cu-O systems (Tc=90 to 150K)[6,7], and some others. The improvement of Tc is very rapid. The measurement of the Hall and Seebeck coefficients shows that they all are p-type superconductors. In 1989, Tokura et al.[8] discovered the superconductors R2_XCexCU04_y(R = Nd, Pr, Sm) with Tc=20 to 24K (onset) and found that the charge carrier is electron in contrast to their hole doped counterparts. This discovery increases the fundamental understanding of the cuprate-based superconductors by comparing their characteristics and mechanisms to those of the p-type superconductors.One of the outstanding features of these n-type superconductors is the difficulty in obtaining samples in good charactors, such as the difficulty in obtaining zero resistivity state in single crystal or bulk samples; the semi-conductivity of bulk samples in ordinary state (opposite to the superconducting state) and a reducing reaction involved before the superconductivity has been found[9]. Therefore, it is necessary to optimize the sample preparation of the n-type superconductors. All the n-type superconductors have been found· considerable solid solubility. The compositional variations play a governing role in the carrier doping of the superconducting phases. Also, it is vital to the ceramic processing of superconductors to identify the compatible phases in the phase diagram. Finally, there is always the possibility of finding additional compounds, both superconducting and non-superconducting, in an unexplored system."

Jan 1, 1996

By Italo Onederra, Miguel Araos

"Most of the current explosives for mining blasting activities are based on ammonium nitrate (ANFO, emulsions and watergels). AN-based explosives’ detonating properties were discovered in the 50’s and since then they have proven to be reliable, safe and cost effective. However, there is no current alternative raw material to replace AN. As part of a program of research initially funded by the Australian Coal Association Research Program (ACARP), Mining3 and the University of Queensland engaged in the search for potential oxidizing agent alternatives that could replace AN in the manufacture of mining explosives. Candidates included those that are produced in large quantities and that can be cost competitive with ammonium nitrate. The initial work identified hydrogen peroxide (HP), calcium ammonium nitrate (CAN) and sodium nitrate (SN). Explosives mixtures were prepared and sensitized using void sensitization techniques. The detonation properties results showed that explosives based onmixtures of HP/CN and HP/SN as the oxidizer were able to detonate in a range of 2000 – 5000 m/s, indiameters 50 and 102 mm, and densities in the range of 0.50 – 1.40 g/ml. Although more studies need to be conducted to fully understand these explosives, if successful, these explosives would be able to offer an alternative to the AN-based explosives in the mining industry."

Jan 1, 2017

By P J. Marsh, P J. Bartsch, N J. Semler

Iron Road Limited is currently studying the feasibility of producing 20 Mt/a of high-grade (67 per cent Fe) magnetite concentrate from a 2.6 Bt resource (JORC) located at Warramboo on the central Eyre Peninsula in South Australia. Bulk concentrate has been tested at a relatively coarse grind size of -106 ¦m. The preliminary flow sheet has been confirmed based on initial mine plans and comprehensive metallurgical testing across the range of mineralisation. Extensive Davis tube testing to predict magnetite recoveries has been conducted over the resource, however this was completed at settings different to the optimised settings developed in the metallurgical test work program.This paper outlines the development of an ore treatment simulation in SysCAD which utilises the mine production plan, the Davis tube test data from the resource, data from metallurgical test work and process design criteria to predict magnetite concentrate deliveries. Mineralogical data, including QEMScan results and metallurgical assessments, were a fundamental basis of the process models which enable predictions of concentrate yield and quality. Power and water requirements are also calculated within the model. SysCAD dynamic simulation has been used to assist with the design of the process plant and downstream infrastructure. The simulation has been set-up to allow iterative integration and optimisation of the mine plan when it becomes available.CITATION:Semler, N J, Marsh, P J and Bartsch, P J, 2013. Iron RoadÆs prediction of magnetite concentrate production from the Central Eyre Iron Project, in Proceedings Iron Ore 2013 , pp 539-546 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Microprocessor-based balances are helping Keffler & Rose Coal Preparation Co. to test and ship coal faster than the competition. They provide a high level of accuracy in meeting Environmental Protection Agency standards and customer specifications .and help minimize "bad" coal. The combination of speed and accuracy has helped increase K&R's sales, while improving the company's reputation for meeting precise client requirements. The quality of coal that is assured by the company's testing-at an in-house lab using fast, precision weighing, and a computerized sulfur test-has assured K&R of a good price for its products. Recent EPA standards have strained the testing capabilities of coal suppliers. Companies involved with high-sulfur coal often use outside laboratory services that can take three to four days to report test results. Since the coal business moves much faster these days, some coal companies cannot afford that kind of time. Too much coal not up to specifications could be produced within a three or four day period. Keffler & Rose took a novel approach to this problem, installing its own in-house laboratory. The test situation immediately improved with this step. However, one bottleneck persisted for a time: the weight measurement procedure for ash, moisture, and energy content. The company first employed a mechanical balance that required time for setting up and taring. The balance provided readings on a conventional scale that was not very precise and allowed for error through subjective readings by the operator. The balance bottleneck was broken when K&R applied new technology to meet its needs: microprocessor-based weighing. The result has been a 75% reduction in weighing time and a sharp increase in accuracy. This has contributed to the test speed needed to keep up with 227-t/h production and precise K&R coal specs.

Jan 11, 1980

By T. Weatherwax, A. Rai, J. Poor

"This paper provides an overview of the current use of auxiliary ventilation products and the challenges with limited air quantity in dead-end entry or working faces. The PVC’s low frictional factor, low physical constraint and minimum leakage properties were ideal to develop as ventilation duct in conjunction with the concept of ""Made in the US and Used in the US"". The PVC duct supports the operational and total cost of ownership with on-going success. This paper will discuss the continuous improvement made in ventilation ancillary products for optimum results. The paper will also cover mine site usage of second generation PVC vent duct underground and the results from the operational and technical side making a difference in health and safety and overall auxiliary ventilation. INTRODUCTION The Barrick Turquoise Ridge Inc. (TR) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestone, siltstones, and mudstones. The weak nature of the ground facilitates the need for underhand cut and fills mining methods.Mining Method; Underhand cut and fill: The mine uses underhand cut and fill method which has 12’x12’ and or 14’x14’ top cuts with several different size undercuts. The ore body is accessed off of a secondary tertiary heading, utilizing a heading with a cross section of 14W x 14H or 15W x 15H configuration. In the wider and more massive zones, two headings in a production panel may be worked at any one time. Drift round lengths are determined by the ground conditions and drift dimension. An example of a typical topcut and associated undercut layout is shown in Figure 2."

Jan 1, 2016

By José J. Suárez

As pressure grows for commodity pricing, new mines are more difficult to develop, the stock markets demand better financial returns from mining companies, resources for the developing and operations are scarce, and developing countries in Asia, and Africa demand more metals, it is important that mining companies effect better utilization of capital to develop capital projects. In the last few years, the costs for Capital projects have been impacted by the following factors:

May 1, 2013

By David Humphreys

It is difficult to overstate the importance of China to the future of the world mining and metals industries. In a remarkably short time, China has risen to become the world?s largest producer and consumer of steel and its second largest consumer of non-ferrous metals such as copper and aluminium. It is currently the world?s largest buyer of copper on international markets, the second largest buyer of iron ore, and the third largest buyer of alumina. At the same time, it is the world?s largest or second largest producer and exporter of tin, lead, zinc, magnesium and a host of minor metals and industrial minerals, as well as a fast-growing exporter of coal.

May 1, 2002

By J. A. Sanchidrián, P. Segarra, S. Gómez

Blasting is a common activity in mining that can cause significant damage in the remaining rock mass. The most commonly used method for predicting vibrations is the Swedish or Holmberg-Persson approach. It is a simple and fast method that uses empirical formulation to estimate the vibration levels based on the explosive charge weight, distance to the source, and other parameters. However, it has limited accuracy and does not consider the effect of free surfaces or other boundary conditions. On the other hand, recently developed methods as the full-field solution (FFS) can provide more accurate predictions of vibrations due to excitations provoked by cylindrical columns of explosive, but the inclusion of free surfaces in analytical methods is a challenging problem. This paper presents a new approach that includes free surfaces in the FFS to predict vibrations analytically in the near-field. The main obstacle to including free surfaces in the FFS was the belief that the solution was non-decoupleable in P- and SV-waves separately. The Heelan's approach was previously used to decouple them, but it only provides valid radiation patterns in the far-field and does not account for intrinsic attenuation. In this paper, we address this problem successfully, allowing for the inclusion of free surfaces in the FFS.

Jan 1, 2024

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998

The cleaning of copper containing fayalite slag using a CuFe alloy was studied under an oxygen pressure ranging from 10-7 to 5 X 10-11 atm at 1200º c. The reduction of copper from fayalite slags by Cu-Fe alloys was found to be very effective. For example, at a P 02 of 10-7 atm, the copper content in the slag was reduced from 4.1 to 0.402 wt. percent after 90 min. of reaction time using a Cu- 5.27 wt. percent Fe alloy. The copper reduction rates were found to be independent of P02 in the gas phase when using Cu-Fe alloys which exhibit an iron activity of greater than 0.4. A mechanism for slag c1eaning is proposed based on the concept that the Cu-Fe alloy lowers the oxygen potential of the slag according to Eq.1 1, fol1owed by the reduction of cuprous oxide by wustite as shown in Eq.2. Here X represents element X in the alloy phase while (X) represents the element in the slag phase. The copper and iron transfer behaviour obtained in this study are explained by a ?Stepwise equilibrium model.

Jan 1, 1985

By Charles Sabine

In 1984 and 1985 at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 27,420-acre part of the 36,600-acre Southern Inyo Wilderness Study Area, CA-010-056, in order to evaluate the mineral resources. The study area is located in Inyo County, CA, near the town of Lone Pine, about 180 miles north of Los Angeles. The study area takes in most of the western slope of the southern Inyo Mountains. Terrain is steep and rugged; the climate is arid. The study area is underlain by folded and faulted marine sedimentary rocks dating from Ordovician to Triassic, Triassic volcanic rocks, and Jurassic to Cretaceous plutonic rocks. Most mineralization was along faults and shear zones in sedimentary rocks. The study area includes most of the Russ and Lone Pine mining districts which produced over one million dollars in gold, silver, lead, and zinc, mostly between 1860 and 1890. A few mines produced ore as late as 1951. Most production was from the Reward, Silver Spur, Long John, and Pennsylvania mines which are outside the study area. Presently, there is no mining activity in the study area; some development work was done at the Reward mine between 1981 and 1984. Dolomite marble is quarried from the base of the range outside the study area. There are currently about 70 mining claims in the study area.

Jan 1, 1986

By K Ehrig, V Liebezeit, E Macmillan

The results from metallurgical test programs are used in feasibility studies for design of new plants and brownfield expansions, in long term mine plans, and to make decisions in an operating plant. There are many elements which contribute to a well-constructed test work program. Ultimately, understanding the accuracy and precision of the test work results is critical to ensuring good decision-making at various phases of a project.Every resource drilling and associated assaying program will have a quality assurance / quality control (QA/QC) component, however this often seems to be overlooked in metallurgical testing programs. The principles of “international standard” or “certified reference material” samples and replicate/duplicate testing can be applied to metallurgical programs, although there are metallurgical-specific considerations in both generating and analysing the data.This paper will describe the QA/QC program carried out within the Olympic Dam geometallurgy program. It will present results in the form of case studies from ten years of testing of replicates and bulk reference samples for industry-standard comminution tests as well as laboratory flotation and leaching tests. The Olympic Dam geometallurgy quality control program has enabled quantification of the precision of metallurgical testing and improved our understanding of the best possible modelling results given the underlying dataCITATION:Ehrig, K, Liebezeit, V and Macmillan, E, 2017. Metallurgical QA/QC – who needs it? The Olympic Dam experience, in Proceedings MetPlant 2017, pp 31–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Oliver Bowles

"The town of Monson in Piscutaquis County, Maine is the, center of an important site industry. Monson slate has a nation-wide reputation, particularly for electrical switch boards, and the deposits have been worked for the manufacture of such products for many years. Open-pit quarrying is the method most commonly employed in obtaining slate. Underground methods have been used in the Peaon Bottom district near Delta, Pennsylvania, but the quarries that were thus operated are now abandoned. Underground methods have been used more extensively in foreign countries, the most famous example being the slate mines at Angers in France, where an over-head stoping method has been employed successfully for many it is only under special conditions that underground methods can be successfully used. If the deposit is wide and relatively thin, or if the material is too unsound to constitute a safe roof, open-pit methods must be used, for slate is too low-priced a commodity to justify the heavy expense of any timbering methods. It is only where the deposit is relatively narrow, of great depth, and sufficiently sound to afford a strong roof that ordinary mining may be employed.The best slate beds in two of the three quarries operated at Monson are no worked by underground methods. The chief bed worked by the Portland Monson Slate Co. is 10 feet thick, stands vertical and strikes N. 63º F. The slaty cleavage is vertical and crosses the strike of the beds at an angle of 5 to 10°. The grain or second direction of splitting is vertical and perpendicular to the cleavage. In addition to the 10-foot bed, to 2-foot beds and one 5-foot bed are available but are not now utilized. In the Monson Maine Slate Co. quarry (the old Pond quarry),a greater number of beds available, but at present quarrying is confined to a single bed about 9 feet thick which dips 30º S.E. and strikes N. 47ºF. The slaty cleavage is vertical and strides N. 45º F., while the grain strikes N. 45-50º W. and is also vertical."

Nov 1, 1920

By T. Orser

In 2010 Newmont made the decision to purchase a 42 foot (ft) Semi-Autogenous Grinding (SAG) mill from Metso and a 28 Mega-Watt (MW) Gearless Mill Drive (GMD) from ABB for the Conga Project in Peru. The test and study work showed that a single line 42 ft SAG mill circuit gave the most favorable project economics in comparison to an equivalently powered single line 40 ft SAG mill circuit. This paper does not address the process design or the project economics, but instead focuses on the key aspects of the SAG mill design, GMD design and the associated component manufacturing. This paper also addresses, where applicable, the potential reliability differences between the initially proposed 40 ft SAG mill and the finally accepted 42 ft SAG mill.

Jan 1, 2012

Separation performance of a Floatex Density Separator (FDS) has been studied both experimentally and theoretically. Experimental results reveal that at a lower bed pressure the FDS acts like a classifier. Higher bed pressure is required to attain the concentration effect as proper development of suspension density occurs under these conditions. It is seen that the size or density alone is not able to describe the partition fully. The terminal settling velocity, which includes both the size as well as the density of the particle can be a useful descriptor of separation in a FDS. While a narrowly distributed feed offers better performance of a FDS, a wide size distribution of feed results in large scatter in the terminal settling velocity distribution and renders the separation difficult. The closely sized feed enhances the density effect in concentration. A higher teeter water flow rate also helps in carrying larger-lighter particles to the overflow by increasing the cut off terminal settling velocity as it increases the net upward force. A detailed description of separation performance in a Floatex Density Separator has also been established from theoretical considerations. Separation performance of the separator is described using a simple slip velocity model. The model has been validated com-paring the predicted FDS performance results with those experimentally measured under widely different operating conditions.

Jan 1, 2014

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

By Jie Li, Longxiang Li, Wenbing Guo, Gaobo Zhao, Yuhang Hu

Surface subsidence caused by underground longwall mining is a very complicated process in time and space, influencing building and structures on the surface of the mining area, including houses, pipelines, and highway. The field monitoring data of surface subsidence are essential for protecting them. This study investigated the dynamic and residual subsidence characteristics of both the surface and the highway over a 730-day monitoring period on a longwall panel. Three monitoring lines (Lines 1–3) were established to monitor the subsidence process, and three stages were identified: initial stage of surface subsidence, active period of surface subsidence, and residual subsidence deformation stage. The maximum subsidence value on the highway (1,786 mm) was smaller than that on the surface (2,094 mm), and the maximum subsidence velocity on the highway (41.7–50.8 mm/day) was also lower than that on the surface (66.7 mm/day). During the residual subsidence deformation stage, both the surface and highway subsidence velocities decreased to below 0.6 mm/day. Furthermore, differences in subsidence characteristics between the surface and the highway were analyzed, with the subsidence value on the highway always being less than that on the surface, while the subsidence velocity during the residual deformation stage was not always lower. This could be attributed to the influence of dynamic loads from vehicles, which could induce additional residual subsidence on the highway. Further investigation into this phenomenon will be conducted in future research.

Jul 1, 2023

By Y Zhang, Z Zhao

The green production of the steelmaking process has urgent requirements for fluorine-free fluxes. In this article, a new solid waste-based slagging flux was applied in the external dephosphorisation test of low silicon hot metal to replace the traditional fluorite-lime dephosphorisation slag. The results showed that under laboratory conditions, the new flux was utilised for smelting low-silicon molten iron with a phosphorus content of 0.10~0.13 wt per cent, the temperature of the molten iron was 1350°C and the slag amount was controlled at 2 per cent. Within ten minutes of smelting, the dephosphorisation rate of the molten iron reached more than 50 per cent. When making slag with new flux, the slag melting time was about 40 seconds and the P2O5 content in the final slag was higher than 8 wt per cent. In the industrial test of a 150 t molten iron ladle, under the same molten iron conditions, an out-of-furnace dephosphorisation test was conducted in the Kambara Reactor (KR) process. The flux material consumption per ton of steel was 8~10 kg. Within 15 minutes of smelting, the dephosphorisation rate of the molten iron was about 30 per cent. During flux slag making, the slag melting time was about three minutes and the P2O5 content in the final slag was higher than 6 wt per cent. This new solid waste-based flux has significant cost advantages and outof- furnace dephosphorisation effects and is expected to become the benchmark for a new generation of fluorine-free steelmaking fluxes.

Aug 21, 2024

About twelve months ago, owing to the increasing quantity of stone and dirt being drawn frQm the Victorian State Coal Mine due to the large amount of dead work below ground, cutting, faults, etc, and to the increasing quan#ty of banded coal beingworked, the writer was forced to consider the question of economy in handling the spoil at the surface. The method in operation at the time was to run out level dumps fro,m the, tipping floor of the heapstead, or brace, and to tip most of the skips of stone in tipplers at the ends of the dumps, the remainder of the skips being side-tipped to widen the dumps.The method, whilst quite satisfactory for dealing with a few skips of stone, was found to be costly as the dumps extended, and the number of skips to be dealt with increased from 300. to 400 per day of two shifts;. therefore, in order to expedite thework and cheapen its cost, the writer devised an improved method which may be qescribed as follows :-(1) The stone is tipped into a hopper car which holds about 10 skips(2) The hopper car is hauled up an inclined dump by means of an electric winch.(3) The spoil is dumped from the car forwards or to either side, as required.(4) The car is returned to the starting point for a further load.Plate I Fig. 1 gives an idea of the construction of the hopper car. In the illustration the car is in position for tipping to one side. The body of the car is supported on a ball race on the under carriage, and it can be swung round to tip in any required direction. The bottom of the hopper is extended to form a 4 ft. lip...

Jan 1, 1918