Search Documents

By D. T. White

"Metallurgical extraction processes often call for the heating of aqueous slurries. Indirect heat exchangers are generally not feasible for service with high yield stress slurries because of low heat transfer rates. It is more appropriate to heat the slurry by direct contact, typically with steam as the heating medium. Although having a long and successful history, direct-contact heat transfer to aqueous slurries has been used without the support of pilot plant research. This paper provides results of the needed research, the work being done at a scale large enough to enable direct scale up to commercial operations. A pilot plant heater was constructed and tested to develop an understanding of the slurry heating process and to ensure that commercial scale heaters were appropriately sized.INTRODUCTIONPressure Leaching OperationsPressure leaching operations are often used to oxidise sulphide gold ores, or for extraction of nickel and cobalt from laterite ores with sulphuric acid. Where there is sufficient sulphur available, the exothermic pressure oxidation reactions can be self sustaining at temperatures as high as 225 ºC, without having to preheat the feed slurry. At lower sulphur levels, slurry preheating is required. This is typically achieved by utilising the flash steam released from the slurry letdown stages and contacting this directly with cold incoming slurry ahead of the autoclave. The vessels where this slurry-steam contact is made are known as heaters or condensers, with the number of pre-heat stages varying, depending on how much heat is evolved in the oxidation reaction (Mason, 1990).In nickel laterite pressure acid leaching processes, which operate between 245 and 270 ºC, the only significant exothermic reactions are those associated with dilution of sulphuric acid in the leach. As a consequence, slurry preheating with flash steam is always used commercially. In practice the number of flash steam preheating stages required varies from 1 to 3, driven by a number of factors, including other uses for flash steam and the upper temperature limit at which preheated slurry can be pumped. A diagram of a typical pressure acid leach train is shown in Figure 1.For pressure acid leaching operations and at low sulphur levels in pressure oxidation, boiler generated direct steam addition to the autoclave is required to sustain the reaction temperature. For this reason it is imperative that the flash steam – slurry heat transfer is efficient and the slurry temperature approaches that of the flash steam closely."

Jan 1, 2012

By W. J. Whiten

"Models of cone crushers and vibrating screens are described. These models have been constructed from actual plant data using a systematic model-building technique. Included in this technique is regression analysis using multi-dimensional spline functions.The models have been used to simulate complete crushing plants and hence to design and evaluate a control system for crushing plants."

Jan 1, 2014

By James J. Olson

Most of the projects summarized in this paper are funded under the Bureau's Advancing Metal-Nonmetal Mining Technology program and are part of the in situ mining subprogram coordinated at the Twin Cities Mining Research Center. The borehole mining equipment development, are funded under the Bureau's Advancing Coal Mining Technology program, is essential to accelerated progress in the in situ mining subprogram, and some background information on this concept is included. The initial in situ research projects started in 1971-72 evaluated some of the critical blast design parameters for in situ copper leaching. The present program totals about $1 million per year and includes in-house research projects, cooperative (cost-sharing) projects with the mining industry, and research and development contracts. Two different extraction schemes are under investigation: inplace leaching and borehole (or slurry) mining. The principal commodity targets for the Bureau's improved in situ mining technologies include copper, uranium, coal, and potash. The principal purpose of this paper is to inform the mining industry of the in situ mining research recently completed or being conducted by the Bureau of Mines. In addition the Bureau encourages companies to comment on the program accomplishments as well as offer suggestions on top priority research needs for improving the in situ mining methods described in this paper.

Jan 1, 1977

By B. Strickland

The decision to accelerate development of Stillwater Mining's East Boulder Mine was made in March of 1998. It required the completion of conceptual designs by July of 1998. This was accomplished through teamwork and close cooperation of mine personnel, engineering firms and vendors, all working toward the common goal of developing an efficient and workable design. Early in the project, representatives of Stillwater Mining, Kilborn International, Parsons Brinckerhoff Transit and Rail Systems, Continental Conveyor, and H.A. Simons met to develop methods to bring the mine into production at a highly accelerated rate and to solve potential bottlenecks, including the movement of personnel, materials, and muck through a 5.6 km (3-1/2 mile) adit. This interaction, including companies not normally associated with the mining industry, led to innovative approaches and designs produced by Kilborn Engineering and Stillwater Mining.

Jan 1, 1999

In this address I look back over the past 40 years of mineral exploration in New Zealand û essentially the period since the Second World War (ie since 1945). It was the period of my personal involvement, and indeed of the personal involvement of a number of you. Luckily it was aperiod of great interest and activity. In the previous 50 years, virtually nothing had happened, and it is kindest to draw a veil over that period. In the very important earlier 40 years (1855 - 1895) the New Zealand gold rush occurred. That must have been a fascinating, rewarding period, which has been thoroughly documented by better historians than myself. I will simply comment firstly that its mineral explorers (gold-prospectors) were very successful indeed, and found most localities of the minerals they sought, in spite of using very different methods from ours of today. Secondly, they were preceeded by one of Maori exploration, which searched for a much restricted list of minerals, but succeeded in finding virtually every locality we know of today. The explorers of both of these early periods were obviously highly successful, but, in the time available, I must restrict myself to the period since 1945. I am currently editing the effective up-dating of Gordon WilliamsÆ 'Economic Geology of New Zealand' (1974). It covers the last 12 years or so. Many of you are contributing to that volume û both as authors and as referees û and I would like to take this opportunity of thanking you all. Although this new volume excludes the energy field, many of us have been involved in it, and I am therefore including energy minerals in this review, as Williams did in 1974.

Jan 1, 1987

By R Wynn, R A. Pax, S Mann, B Cornish

The semi-autogenous grinding (SAG) mill at the MMG Century operation has failing load cells that are essential to the control strategy used to stabilise the mill. Currently, mill-bearing pressure is used as a proxy for the load cells, but it has been found to be a noisy signal and lacking in useful sensitivity. It is also prone to variations and drift due to temperature. After consideration of a number of options, a non-contact acoustic array has been installed around the SAG mill to provide a more stable proxy load signal as well as other information about the internal operation of the?mill.The installation consists of 12 microphones to provide some detail into the operational differences that occur during normal operations at the MMG Century SAG mill. This acoustic approach acknowledges that operational grinding mills emit significant acoustic emissions that are a consequence of the dynamic environment prevailing inside them.Previous studies have attributed the acoustic noise to a range of events that occur inside these mills (Pax, 2011; 2012). Consequently, non-contact acoustic determinations of in-mill behaviour can provide powerful insights into the operation of the primary comminution tumbling mills. By measuring key microphone signal attributes at different positions around a mill, a holistic picture of mill internal operation can be developed.This paper will describe the installation of the 12 microphones and discuss the use of the acoustic load signals as a proxy for failing load cells. It will also present data from new observations of internal mill dynamics and the results of implementation of control using these acoustic signals. Key to the control approach has been the development of a logically coherent picture of the processes inside the mill.CITATION:Pax, R A, Wynn, R, Mann, S and Cornish, B, 2014. Implementation of acoustic arrays for semi-autogenous grinding mill?operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 273–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By A. J. Kraemer

This report on research and experimentation by the Federal Bureau of Mines on technologic and scientific problems of the petroleum and natural gas industries presents a resume of work from July 1, 1953, to June 30, 1956. The preceding report, for the fiscal year ended June 30, 1953,3/ indicated continuation of the Bureau's program of petroleum and natural gas research of world-wide significance, which began in 1910. The petroleum and natural gas research of the Bureau of Mines is divided into five main categories: (1) Production of petroleum and natural gas, (2) transportation and storage, (3) petroleum chemistry and refining, (4) thermodynamics, and (5) economics.

Jan 1, 1959

By K. L. Bainbridge

This report describes the results of a study to determine which types of, and to what extent, mining wastes can contaminate groundwater through leaching of acid-forming or potentially toxic constituents. The primary focus of this study was on coal mining wastes, especially overburden spoils and preparation plant refuse. In addition, the potential for contamination by leachates from clean coal stockpiles was also examined. The study approach included investigation of (a) the amounts and geographic locations of mining wastes in the United States; (b) the chemical character of mining wastes, especially with regard to potentially acid-firming or toxic constituents; and (c) the extent to which acid and/or toxic components are leached from mining wastes by rainwater. To evaluate the leachability of coal wastes, a laboratory waste leaching method was developed during this study to specifically simulate the leaching process over a long-term. Waste samples collected during this study were also leached by the EPA extraction procedure and ASTM waste leaching method. Results of the three leach test methods were compared to evaluate their relative capabilities to predict the leachability of mining wastes.

Jan 1, 1980

By ELLSIVOKTH DAGGETT

THE Berlin gold quartz mine is situated in Nye county, Nevada, on the west flank of the Shoshone range, about 40 miles south and 30 miles west from the town of Austin, the county-seat of Lander county. The distance from Austin is about 60 miles by stage-road. The outcrop of the vein, at the top of the incline-shaft, is situated just at the base of the mountain proper, almost exactly at the intersection of the mountain-side with the gravelly bench that slopes for about three-quarters of a mile to the flatter sage-brush plain, or desert valley, below. The -vein itself consists almost entirely of quartz, with perhaps 2 per cent. of sulphide of iron, copper, lead, zinc and antimony, and perhaps a trace of some of the compounds of tellurium with gold and silver, although none of the latter have been as yet positively identified. The relative proportion, by weight, of silver and gold in the ores, varies in different parts of the vein, from 12 silver for 1 of gold, to 7 silver for 1 of gold. The quartz vein-filling is usually frozen fast to the walls, and is very hard and compact, seldom showing the friable, fissured, or shelly structure often to be found in quartz veins. Comparatively little evidence of relative motion of one wall of the vein upon the other is to be found-a fact indicating that during the formation of the vein, and prior to the extensive movements herein described, little disturbance had taken place. No evidence whatever of metasomatic origin has been observed. On the other hand, occasional occurrences of comby structure, in which the axes of the quartz crystals are at right angles to the plane of the vein, rather indicate deposition from solution in a pre-existing fissure. Spurs, or branches, and small parallel veins, while not en-\

Mar 1, 1907

By B. J. Dave, Ashok J. Desai, Allen J. Hulshizer

This paper presents various design and construction considerations involved in developing an underwater installation of lined, large diameter shafts not known to have been previously accomplished for the diameter size, depth or ground conditions identified with the Seabrook Power Station. Outlined approach provides for driving tunnels independent of shaft sinking operation, permits the use of prefabricated shaft lining and incorporates a safe dry tap method for connecting the shafts to the tunnels. INTRODUCTION The Seabrook Power Station, located two miles inland from the Atlantic Ocean, at Seabrook, New Hampshire, is a two unit, nuclear powered, electric generating plant, each unit having a capacity of 1150 megawatts (electric). Typical to all steam driven generators is the requirement for large quantities of water. Requirements for the Seabrook Plant will be met by intaking and discharging approximately 850,000 gpm of ocean water at a considerable distance from the shore line in water depths that render the environmental impact inconsequential. Obtaining, conveying and discharging such large quantities of water represents a major undertaking, particularly under today's environmental controls. Tunnels are well suited to reducing the environmental impact at the Seabrook site by conveying the water about 250 feet deep under the salt marsh (a valuable ecological feature) and under the beach well out into the ocean without any noticeable ground surface disturbance. An alternate approach utilizing trenched piping would have created some disturbances and was environmentally less desirable. The tunnels connect to intake and discharge

Jan 1, 1976

By B. H. Caudle, A. D. PUCKETT

This paper summarizes precent knowledge of the ignition qualities of pure hydrocarbons likely to be present in modern Diesel engine fuels, as shown by an extensive search of the technical literature. The report also discusses the possible significance of cetane number and hydrocarbon struc- ture. Cetane or cetene numbers, and other physical properties, are tabu- lated for about 100 hydrocarbons, and a bibliography is appended. In recent years the Diesel engine has enjoyed increasing popularity due to its dependability, inherent characteristics of fuel economy, and the fact that it operates on a fuel that hitherto has been available in comparatively large quantities at a low price. These qualities have en- abled the compression-ignition engine to compete very favorably with other types of prime movers in many fields and have led to predictions of fur- ther rapid expansion in the application of Diesel power. In a survey of the field of all petroleum fuels for combustion engines, Holaday et al (9) have predicted that by 1948 railroads will be using 10 times as much Diesel fuel as was used in 1939 and that over-all consumption will have doubled that of 1939. Other estimates of the yearly demand for Diesel fuels five years hence vary from 2,6 to 5 times the amount used in 1944. Into this picture has come the question of whether the greatly in- creased production to meet this estimated demand is compatible with the maintenance and possible improvement in quality of fuels necessary to satisfy future engines. Unfortunately perhaps for the Diesel engine, factors other than those of simple arithmetical multiplication must be considered. For example, the consumption of oil in central heating plants doubled from 1935 to 1943, and a further increase of 57 percent of the 1943 demand is expected by 1950. Jet propulsion has been developed to the stage where it is entirely practical for military aircraft. Catalytic cracking plants, many of which were constructed to meet the war- time accelerated demand for high-octane gasoline, are taking their place in the refining industry. All these developments, as well as the Diesel engine, require material of approximately the same boiling range. Virgin gas oils make excellent burner fuels, perform most satisfactorily in the gas-turbine units for aircraft according to present information, and are at a premium as catalytic cracking stock.

Jul 1, 1948

By Miguel Gutiérrez

This paper will seek to provide an awareness of the challenges the permitting process presents to the engineering design for open pit mining projects in Perú. This awareness will create a better understanding of the permitting process within the several groups in mining companies that are responsible for getting the mine project started or continue its operations.

Sep 21, 2013

By GEORGE T. Harley, Walter R. Storms

This paper, which describes mining mothods at International Minerals & Chemical Corp, 'e. potash mine. in. Eddy. County, N. Mex., is one of a sories being prepared by the Mining Branch of the Bureau of Minos. on mining method a and practicos in, various mining districts of the United States. The mine shafts and. surface plant or International Minerals & Chemical Corp. are situated. in. sec.. 12, T. 22 S., R. 29 E., N. M. P. M., about 26-1/2 miles by paved highway east of the city of Carlsbad (figs. 1, 2, and 3). A spur line of the Atchison, Topeka & Santa Fe Railroad connects the mine with the Clovia-Pecos branch of the same road near Loving, a few miles south of Carlsbad. This spur also serves the refinery of United Staics Potash Co. This report gives. the history and describes the geology of the district. Methods of prospecting, exploration, sampling, and estimation of tonnage and values are explained; development and mining methods are discussed in con- siderable detail; transportation, ventilation and drainage are outlined; safety measures are noted; and the wage scale and organization are mentioned.

Jun 1, 1949

The key issue which determines the use of imaging for explosives and mining research is the question - `What information will I gain by using imaging technology?' This paper will address that question from the point of view of a researcher and cameraman working in industrial imaging and photography. The paper will establish a common set of reference standards for high speed imaging and photography which researchers can apply when deciding which type of imaging technology is appropriate. It will present an overview of current image analysis technologies and practices in use across a range of appropriate scientific fields and draw lines of commonality of approach between these fields and the field of explosives and mining analysis and research. Further to this, the paper will examine the different technologies from an image quality reference point, ease of operation, cost, and reliability parameters. Finally this paper will present an argument for the hybridisation of established and new technologies which could provide a more beneficial approach to the use of imaging as a tool of research and analysis in the explosives and mining industries. This will include a novel approach to high speed filming and analysis in the field which should deliver high quality images in a time frame which is more appropriate to urgent action and solutions.

Jan 1, 1995

By D. K. Adjei, G. Ofori-Sarpong, R. K. Amankwah

"Mercury (Hg) is toxic and has long-term effect on the muscle tissues, the brain and the central nervous system functions due to its bioaccumulation and biotransformation effect. Hg pollution around the world is high and this has attracted much global concern such as the Minamata Convention on Mercury, held in 2013. For several years, mercury has been the chemical of choice for Artisanal and Small-Scale Mining (ASM) gold extraction, accounting for about one-third of the global mercury consumption. A greater percentage of this ends up in the environment through open burning of amalgam, spillage and indiscriminate disposal of waste. To break this wall of mercury pollution, it is very important for the mercury used to be recycled through the use of mercury retort units. This brings into the limelight, the Lantern Retort which tries to synergise the high conductivity of steel and the see-through effect of glass, thus, improving the amalgamation process. A research conducted on improving the original Lantern Retort arrived at an appropriate distillation length of 5.08 cm which was used in redesigning a more efficient retort. The improved Lantern Retort recovered about 98% of the mercury used. INTRODUCTION Artisanal and Small-scale mining (ASM) is an informal mining activities which employ quite simple tools such as pickaxes, sluice boxes, shovels, chisels, metal bars, mattocks and water pumps for mining and processing of gold ores. The artisanal and small-scale mining (ASM) sector has served as source of employment for many people in developing countries including Ghana (Aryee, 2001; Hilson and Potter, 2003; Amankwah and Anim-Sackey, 2004; Amankwah et al., 2010) and has provided a substantial amount of foreign exchange through its activities (Hilson, 2001; Styles et al., 2010). Hentschel et al. in 2003 estimated that about thirteen (13) million people are said to be engaged directly in the small-scale mining activities worldwide. However, an estimated 100 million people are said to depend on this sector for their livelihood mainly in developing countries. In China alone, a projected number between 3 and 15 million people are engaged in artisanal and small-scale mining activities (Hentschel et al., 2003), whilst in Ghana, it is estimated that more than 1,000,000 people are employed directly or indirectly in the artisanal and small-scale mining activities, with 10% being women (Amankwah and Anim-Sackey, 2004; Amankwah and Ofori-Sarpong, 2014). In Ghana, ASM gold production has grown from a low of 2.2% in 1989 to a high of 34% in 2014. This figure is estimated to increase with proper documentation. This indicates that the sector has made significant socioeconomic impact on many individuals and communities as a whole. Notwithstanding the above positive contributions, the sector has also contributed to negative impacts on human, aquatic life and the environment in general due to indiscriminate mercury emission. This ‘pollution wall’ needs to be broken, and several interventions have been put in place including the use of retort units like the lantern retort (Adjei et al., 2014; Amankwah and Ofori-Sarpong, 2014)."

Jan 1, 2017

By Charles L. Kimbell

The year 1980 on the whole was not a good year for the world's mineral industry. The general upturn of activities in 1979 after a rather poor 1978 showing was not maintained with a number of key measurement standards showing downturns. Most notably, the world's steel and petroleum industries recorded significant reductions in output, the former in response to markedly lower demand levels and the latter partly in response to lower industrial consumption owing to general economic conditions and partly owing to successes in campaigns for the reduction of energy use in general and petroleum product use in particular among major importing nations that were feeling the trade balance pinch of ever-higher oil prices. During 1980, a number of political events-some international in scope, some confined to single nations-had significant influence upon world mineral industry activities and mineral commodity supplies, and other political happenings had the potential to significantly affect the industry in future times.

Jan 1, 1982

By Yael Miron

The presence of pyrite (FeS2) in coal can cause or contribute to several problems for the coal mining industry. These problems, which include spontaneous combustion, roof falls, floor heave, and accidental explosions in coal surface mining when ammonium nitrate fuel oil (ANFO) explosives are used, result from pyrite oxidation. Pyrite oxidizes exothermically in the presence of air and moisture to form a large variety of products, including hydrated ferrous and ferric sulfates, and sulfuric acid. Some of the products are reactive chemicals and strong oxidants. The volume of many of these oxidation products exceeds the original volume of the pyrite; as a result, the adjacent coal disintegrates and its surface increases, rendering it more susceptible to oxidation. The heat from pyrite oxidation raises the temperature of the adjacent coal, accelerating the oxidation and self-heating rates of the coal. These combined chemical, physical, and thermal effects are the cause of the aforementioned problems. When ANFO is used in surface coal mines and contacts ferrous sulfate, a highly exothermic reaction ensiles. Additional hazards are fires or explosions caused by the frictional ignition of methane when the pyrite in the coal is struck by a cutting bit during mining.

Jan 1, 1994

By Charles A. Lindberg

Mobile cranes on tires are perhaps the most important accessory in truck-haulage pits. They usually are of 20-ton capacity at short radius and with outriggers but have considerable overload capacity. Standard booms are 30 ft but have 10-ft extensions with which they are usually operated. Cranes have two engines, both originally gasoline, but 150-hp Diesel engines have been found more reliable for the propulsion motor, the 100-hp gasoline motors being retained for hoisting. Pro- visions are made for dropping the ballast counter- weight to reduce axle weights to legal limits for highway travel. The weights are carried on a regular truck or are transported on an extra trailer axle behind the crane. Tractors-Probably equalling the cranes in usefulness are the track-laying tractors which are used to prepare roads and other surfaces, to clean up at the shovel, and for dozing on stripping dumps. A new type of tractor mounted on rubber tires has been tried out on the Mesabi Range for the past year and a half. The advantage of this design is its mobility which makes it capable of taking care of the spill at the shovel and then running to the dump to clean up. Alternating between these two jobs, it relieves heavy tractors that can be used to better advantage on heavier work that does not require so much traveling. This tractor can travel at speeds of 12 to 13 mph and is designed to facilitate repair of the expendable parts. Weaknesses have developed in the internal construction which have seriously marred the performance record of this unit, but when used within its capacity it is quite successful.

Jan 1, 1949

The theme of the conference is "excellence", an epithet of special significance in tertiary education. It appears in the mission statements, goals and plans to achieve them of most, and quite possibly all, tertiary institutions in Australia. In the context of excellence, this paper examines the current statue of professional education in the principal mining industry related discipline of Mining Engineering. It furthermore, identifies and discusses a number of special problems in mining education that the tertiary sector has long endured. Some of these problems are becoming acute, and solutions will have to be found soon in order for the industry to be assured of the supply of well motivated and appropriately qualified young engineers and scientists necessary to achieve and maintain the excellent to which it aspires.

Jan 1, 1989

By David C. Girard, Larry Williamson, Leonard R. Benson, Ronald E. Bizzarri

On the east side of Washington DC, the DC Water & Sewer Authority is developing a Facility Plan for the Anacostia River CSO Control Projects, including 8 to 12 miles of CSO storage/conveyance and flood relief tunnels and associated facilities. The project includes major technical and non-technical challenges, including: completion under a Federal Consent Decree schedule; large diameter (estimated 25 to 35 ft) soft ground tunnels and shafts up to 200 ft depth; operations without use of active flow control systems; and close coordination with several major public and private construction and development projects that are being advanced in the project area.

Jan 1, 2007