Search Documents

By H. J. Gerritsen

From presently available components a portable, rugged, reliable apparatus can be built which will be able to detect methane concentrations of 0.1% and lower in air. Sensitivity and design considerations of the apparatus are given. Ways to build even simpler and cheaper apparatus in the future are indicated. Traditionally the problem of detecting and monitoring the presence of dangerous gases present in small concentrations in air has been a difficult one. Whether canaries,' or sophisticated chemical or thermal conductivity methods are used, they seem to be either slow, cumbersome, or otherwise not completely satis factory. A seemingly natural way of gas detection is to measure the strength of absorption undergone by light of a wavelength that the gas to be detected absorbs. This method has been difficult to apply in view of the low power output over a narrow wavelength range in the infrared from traditional glow bar light sources. Besides, the apparatus to select such a narrow band of wavelengths is quite costly and complex. The use of a laser solves these problems simultaneously. Although a variety of lasers are available to detect a variety of gases (such as carbon monoxide or methane) whose early detection would be desirable, this paper deals exclusively with the use of lasers for methane detection. ABSORPTION SPECTRUM OF METHANE IN AIR The absorption spectrum of pure methane is very well known.2-4 There are four fundamental vibrations, all occurring in the infrared of which only two absorb strongly. They occur at 3.3 µ and 7.7 µ. The absorption spectrum is quite complicated due to the fact that the methane molecule can rotate in a variety of rotational quantum states. These rotational states are furthermore split by anharmonic forces such as the Coriolis force.4 When methane is present in air at atmospheric pressure, much of the very fine structure due to the anharmonic force is washed out since the pressure broadening is of the same magnitude as the splitting due to anharmonicity. For most of the spectrum at 3.3 µ, the rotational lines are typically separated by 0.01µ while the individual linewidth is 0.0001 µ. It is thus very important that the laser emit at a wavelength that coincides with one of these rotational lines. Before elaborating on the point that such a laser exists and how it performs, it is necessary for later discussion to point out that in the

Jan 1, 1967

Refractory gold ores have been the subject of intensive metallurgical study in order to achieve more efficient recovery of contained values and at the same time to minimise environmental impact. Considerable innovative gold processing technology was introduced in New Zealand last century, the most notable being the first successful commercialisation of the cyanidation process by the Crown Mines Company at Karangahake in 1889. The Karangahake gold-silver deposit was second only +to the Waihi Martha mine in total bullion production from the region with active mining from 1882 until about 1920 and sporadic production between 1930 and 1944. Reevaluation at Karangahake with associated metallurgical testing has continued since that time becoming particularly active in the last decade as a result of increasing gold prices. Gold processing technology is reviewed and results of some recent test work are presented and discussed in the context of Karangahake history and future development possibilities. This work confirms the variability and complexity of the Karangahake deposit both mineralogically and metallurgically and suggests flotation followed by new and innovative smelting is the most appropriate processing route for the recovery of gold from the high grade ore which could be produced from the Karangahake workings in moderate tonnages.

Jan 1, 1993

By J. de Villiers

Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine analysis. The method, however, requires a good initial calibration and periodic checks on its precision and accuracy. Several examples from minerals processing, pyrometallurgy, and materials science show the strengths and applicability of the method. The limitations and sources of error are also discussed.

Jan 1, 2007

By J. E. Gill, A. R. Byers

"The property of Sladen Malartic Mines, Limited, is in the northern half of Fourniere township, Abitibi county, Quebec. The group is large, but the part so far found to be of economic interest is a strip 3,200 feet long between the Canadian Malartic property to the west and the East Malartic and National Malartic properties to the east ( Fig. 1).The original claims were staked in 1923 and 1924 by St. B. Sladen and H. S. Kennedy because gold was known to occur on claims nearby. In 1928, detailed mapping of the Malartic Gold Mines property (now Canadian Malartic) showed the presence of an east-west gold-bearing zone traceable almost to the Sladen boundary. During the winter of 1929, a hand-driven drill was used to secure short sections of core through casing pipe sunk to bed-rock. This proved the existence of the main Sladen ore zone, but it was not until the price of gold was increased, in 1934, that serious work was attempted.Underground work was started in 1935 and milling in January, 1938. To the end of 1945, 168,882 oz. of gold were recovered from 1,641,974 tons of ore, an average of 0.103 oz. a ton.GEOLOGYThe bed-rock underlying' the Sladen Malartic property consists mainly of Precambrian greywacke and volcanics that appear to form a conformable series with a general northwest strike and vertical to steep northerly dip. Except where disturbed locally by drag folds or faults, tops face north. Intrusive rocks that range in composition from diorite to granite cut the sediments and volcanics. The basic types, generally quartz diorite and diorite, form dykes or sills in the volcanic rocks. The more acidic types, mainly quartz syenite and related porphyries, intrude the volcanics and the sediments in the form of dykes, sills, and larger, stock-like bodies.The orebodies are parts of slightly shattered or brecciated zones, mainly in greywacke, but partly in syenite, diorite, and volcanics, that have been more or less replaced by fine-grained quartz, pyrite, and minor amounts of sphalerite, galena, sylvanite, petzite, and gold."

Jan 1, 1954

By Roberto Galéry, Braz J. C. Filho, Marcelo M. Stopa, Douglas B. Mazzinghy, Priscila M. Esteves

"The purpose of the research is to monitor ball mill filling by means of signals usually measured in its electrical drive. The method is based on the mill torque estimated from rotor speed and induction motor stator voltage and currents. New signal processing is presented in both time and frequency domain for measurements in a dry laboratory ball mill. Statistical analysis is applied to time series resulting in good correlation to mill filling. Fast Fourier Transform (FFT) and power spectral density (PSD) also resulted in an accurate filling indicator. The proposed method does not need any sensor to be installed directly on the mill and requires only sensors usually available for motor control purposes. The experimental results showed that the method have potential to be used to construct an automatic system for monitoring operational variables in ball mills. The aim of this monitoring is to improve energy efficiency, reliability and productivity.INTRODUCTION Recently, a great number of papers have pointed the importance of ball mill filling monitoring and also of grinding control (Lu, et al., 2014) (Ramasamy, et al., 2005) (Tsamatsoulis, 2014) (Zhou, et al., 2009). Additionally, great amount of control techniques have also been presented with several complexity degrees (Tsamatsoulis, 2014). According to Eremenko (2015) the lack of effective and accurate methods for fill level measurement is the main reason that makes mill optimal control so complicated. It happens because nonlinearity, long time delay and time varying features of the ball mill turns difficult to develop a truly efficient method for monitoring filling. At the same time, fill level has a determining role in charge motion and consequently on particle breakage. For low levels of filling many energy is expended in impacts with very low breakage efficiency. Those impacts can also damage mill liner. In contrast, high levels of filling causes damping effects that reduces breakage and can also affect energy consumption. Based on this it is conclusive that fill level measurement of ball mills is an important issue for grinding efficiency. This fill level information can be used for operators to control ball mills and also for engineers to run simulations and improve confidence levels of circuit designs (Shi, 2016)."

Jan 1, 2018

By Steve Dillingham

PHYSICAL BLAST DATA Pattern Description All measurements related to the description of the physical blast pattern must be made with the mind-set that it has to tell a powerful factual story enabling a future accurate reconstruction of the event. A case has never been lost because too much factual information was available to assist investigators. An accurate physical description of the pattern must be provided based on the blaster’s observations of the pattern actually loaded. The blaster must measure the pattern size, depth, face heights, etc., recording only accurate results. All too often, a blaster records simple pattern sizes and information relayed to him or her from the driller, or from a phone call into the office the night before for powder pre-load inventory purposes. If a pattern was actually measured on the job site by the blaster to be 8.5 x 9.5’, it may, in fact, originally have been ordered at 9’x9’, 8’x9’, or 9’x l0’. In a claim situation, particularly flyrock, recording a “generalization” of what was loaded could result in an interpretation of a blaster’s negligence due to “not knowing or caring” what the actual pattern was, and not loading appropriately for conditions. It is important to remember that other documentation exists such as a drill log from a contract driller or mine records that may provide a different interpretation of the loaded pattern.

Jan 1, 2002

By Thomas Barkley

Until the recent past, blasters have provided good to excellent results with tools and processes that have an inherent error. These errors can be found in drilling, explosives delivery quality and consistency, explosives loading consistency, actual explosives performance, and pyrotechnic detonator initiator accuracy. My experience and data from several decades in the industry show the error is often times 10% or higher larger in the dimensions that measure the performance of each of these tools and processes.

Jan 1, 2011

By M. A. Neri

A lead-free solder alloy Sn-57.5Bi-0.5Ag has been developed by mechanical alloying and foundry processes, and has great potential as a lead-free solder system, to low temperature applications. The mechanical alloying powders show a microstructure different to the microstructure obtained by the foundry process for the same alloy. Its melting point of 142°C is slightly higher than that of eutectic tin- bismuth solder. Examination of the microstructure revealed that eutectic microstructure is refined by the mechanical alloying process Ag additions. The lamellar structure of tin-bismuth gradually disappeared with the process of mechanical alloying, while intermetallic compounds AgaSn phase was formed. The Cu-Sn intermetallic compound layer formed at solder-copper interface is the Cu6Sn5 phase. Keywords: Lead-free solder, Microstructure. Mechanical alloying

Jan 1, 2003

By Zhangm Zeqiang, Manman Lu, Hanquan Zhang, Hong Yu, Jintao Fu

"Pelletizing is an important technique in the ironmaking industry. Artificial and natural magnetites are materials that are widely utilized in the iron ore pelletizing process. In this work, the pelletizing characteristics of these two types of magnetite have been investigated in detail. The obtained results shown that in contrast to natural magnetite, the artificial magnetite concentrate exhibits stronger hydrophilicity, lower electronegativity, larger specific surface area, and rougher surface. In addition, the green pellets produced from the artificial magnetite concentrate are characterized by a higher compressive strength as compared to that of the pellets obtained from the natural magnetite concentrate. However, the shock temperature of the artificial magnetite pellets around 255 C is significantly lower than the threshold specified by the industry. The balling characteristics of the material obtained by mixing 20% of the artificial magnetite concentrate with 80% of the natural magnetite concentrate are considerably improved with respect to those of the individual components.INTRODUCTION Pelletization is an essential process of the ironmaking industry in China. Since the pellets produced from iron ore exhibit high mechanical strength, good particle granularity, and uniform shapes, pelletizing high-grade iron ores with good metallurgical reducibility can lower the coke ratio, improve their technico-economic index, and reduce the cost of processing pig iron in blast furnaces[1, 2]. Presently, high-grade magnetite is a material utilized for pelletizing various iron ores across the globe. However, its natural deposits have been depleting rapidly in recent years; as a result[3], China’s dependence on the foreign high-grade iron ores exceeded 70% in 2009 and reached the level of 87% in 2016. Hence, possible methods for the efficient cultivation of limonite, siderite, hematite, and other refractory minerals that correspond to low-grade, finely sized, inhomogeneous, and scattered iron ores have attracted significant attention [4, 5]. In particular, magnetization reduction roasting and magnetic separation techniques, which are widely utilized for obtaining high-grade artificial magnetite, represent effective ways of processing iron ores that can alleviate the scarcity of natural magnetite resources [6, 7]. The artificial magnetite produced by magnetization reduction roasting exhibits different characteristics as compared with those of natural magnetite (including the degree of hydrophilicity, surface potential, specific surface area, and other surface physicochemical properties[8-11], which significantly affect its pelletizing behavior. In this work, the surface characteristics of artificial and natural magnetites are investigated in detail, and their effect on their pelletizing properties (such as green ball strength, heat stability, and pelletization rate) are examined."

Jan 1, 2018

By McCarthy. Richard E.

The prime movers of the Centralia Project, the surface coal mine and the power plant, private utilities are very aware of public attitudes. They have established and maintain the reputation for leadership in public service and are genuinely concerned that this project initiate the pro-grams and design the hardware to answer the question :What will be the impact of the mine and the plant on the physical environment, i.e., the air, soil and the water." So in the beginning almost as soon as the decision had been made to go ahead with the project, officials of the two private utilities, Washington Water Power and Pacific Power & Light went on record and publicly stated time and again that the overall approach of the Operators would be to do all that was reasonably possible to safeguard the environment. This attitude became part of the thinking of the project planners, part of the design of the power plant and part of the plan for the surface mine. The coal to be mined is from the Skookumchuck formation. The formation is Late Eocene and is made up of poorly consolidated marine and non-marine deposits. The major overburden removal equipment is a bucket-wheel excavator -conveyor system and a 56 yard dragline. Mining of the coal will be done with truck and shovel. The coal is processed, washed and crushed to 1 ¼ " for delivery to the power plant. The muddy water created by the washing process is chemically treated and the solids removed by a thickener-vacuum filter system.

Jan 1, 1971

The key aspects of process metallurgy that distinguish platinum group metal (PGM) concentrate smelting from that of other base metal sulphide concentrates are presented. These differences include considerably higher input chrome and magnesia contents that directly raise the slag liquidus temperature and have the potential to increase accumulations of refractory spinels. Most importantly, the higher processing temperature required for PGM smelting and the resulting very high matte superheat lead to considerably more onerous smelting conditions than those typical of other smelting operations. This has presented challenges to furnace design and integrity, especially when coupled with the progressive intensification of smelting, involving doubling, and then redoubling, of furnace power inputs over the past 20 years. These power increases have been enabled by increasingly more advanced furnace cooling and structural technologies. Key technologies include strong constant-force spring-loaded bindings acting in three dimensions to minimize infiltration of superheated matte into brick joints, and robust well-cooled tapholes for reliably tapping the superheated matte. The result has been substantially improved productivity, and reduced smelting capital cost outlay per unit of production. A significant challenge, which was not anticipated, presented itself in the form of insidious corrosion of the furnace lining, and especially high-intensity copper cooling elements. Investigation of corrosion in related industries eventually identified chloride-accelerated sulphidation', and this term has been retained as it generically describes the most pertinent aspects of the accelerated low-temperature wear of copper coolers observed in PGM smelting. In addition to discussing the corrosion mechanism, this paper describes a number of solutions that were developed jointly by Anglo American Platinum and Hatch to address the copper corrosion problem. First, new monitoring technologies allowed furnaces to be operated more safely for a longer period of time. Second, a system for replacing corroded coolers from outside the furnace during a fast 'hot' shutdown minimized the impact on furnace operating factor and hearth life. Finally, a corrosion-resistant graphite-protected cooler design significantly improved furnace campaign life, and heralds a more lasting solution to cooler corrosion in PGM furnaces.

Jan 1, 2013

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

By Abb Raymond

Finely processed industrial minerals in "powdered" form have long been utilized by the plastics, paint, rubber, paper, ceramics, and adhesives industries as fillers, extenders, coatings and special additives. These minerals, primarily calcium carbonate, talc, kaolin, titanium dioxide, and the like, have provided economic, uniform and consistent base materials which have, in turn, been used by the referenced industries to manufacture quality products. The focus of this paper will be the development of equipment and systems at ABB Raymond for the dry processing of such non-metallic minerals in order to meet what have become increasingly stringent requirements of the producers of these minerals. Changes in these requirements seem to have been accelerating rapidly during the last ten years, and it is expected this process will continue into the 1990's.

Jan 1, 1990

By C. E. Wicks, F. E. Block, F. D. Stevenson

The vapor pressures of tungsten (VI ) chloride ( WC1 ) and hafnium ( IV ) iodide ( HFI ) were measured by a metal diaphragm technique . Vapor pressure values were obtained to permit calculation of the thermodynamic properties of the vaporization processes of the compounds . The vapor pressure data of WC16 are represented by the following equations for the liquid , B - solid , and a- solid over the temperature intervals indicated : - log P = 8.194 3,253 /T Liquid , 281.5 ° to 325 ° C : B - solid 230.0 ° to 281.5 ° C : log P a - solid 185.0 ° to 230.0 ° C : log Pam *** = 8.794 - 3,588 / T = 9.615 - 3,996 /T where T is the absolute temperature in degrees Kelvin . The heats of vaporization and sublimation are 14.9 , 16.4 , and 18.3 kcal / g mole , respectively . The entropy of vaporization at the normal boiling point , 330 ° C , was 24.3 eu . The fusion temperature , 281.5 ° C , and transition temperatures , 230.0 ° and 185 ° C , were found by thermal analysis .

Jan 1, 1964

By Bernard J. Steblay

Millions of mechanical anchor roof bolts are used each year for mine structural support. The benefit of this bolting depends on a number of factors including rock density, bolt length, in situ stresses, time elapsed between mining and installation, rock properties, bolt patterns, and tension (Lang, et al., 1979). Installation tension is a major determinant of support quality. Postinstallation tensions indicate both the usefulness of the individual bolts and the behavior of the reinforced rock structure. The importance of short- and long-term bolt tension measurements is well recognized, and such measurements are required by regulations (Fed. M/NM Nine Safety and Health Reg.). These regulations also take into account the difficulty of practical tension measurements. Only a statistical sample of the bolts installed is required to be measured using current torque wrench technology. Drawbacks to this practice are that the anchorage is disturbed and perhaps weakened, accuracy is limited by friction to about 30% (Lang, et al, 1979, and Barry, et al., 1956), and the procedure is relatively time intensive.

Jan 1, 1984

By Javad Sattarvand, Amin Moniri-Morad

Predicting equipment failure behavior plays a critical role in providing a safe operation. Although various reliability evaluation methods are available for estimating failure behavior profiles, these approaches are based on mathematical formulation, leading to actual operation simplification and improper estimation of failure trends. This study proposes a discrete-event simulation (DES) approach to model fleet failure behavior. This approach can model the maintenance strategies in multi-component systems with minimum simplifications. In this regard, the first step was to collect a historical failure time dataset (e.g., the time between failures). Then, the DES model is established to predict the severity of failure events and design maintenance strategy considering actual operation circumstances. Afterward, the maintainability analysis was performed to estimate equipment downtime and availability. The achieved results showed that the system availability was about 85%. Also, the findings demonstrated that the DES could efficiently predict the equipment failure behavior using various stochastic events.

Jun 25, 2023

By A. R. T. Denues

"INTRODUCTION The Explosives Division of the Bureau of Mines, United States Department of the Interior, is investigating cushioned blasting at the Explosives Testing Station, Bruceton, Pa. The general interests of this investigation are practical and relate particularly to safety. The immediate concern is an application of cushioned blasting in coal mining.In cushioned blasting, various means are employed to reduce the intensity of the application of energy in an explosive action in a borehole. The primary object is to increase the efficiency of the use of explosives. Cushioned blasting is designed to save the energy usually lost in excessive shattering and in this way to effect economies and to produce increased proportions of desirable lump coal. That this saving should lead to greater efficiency is indicated by an analogy with the theory and experience of size-redaction by crushing or grinding from which it is known that a large proportion of the energy consumed is expended in producing the smaller sizes (26),3/. Aside from these considerations, increasing the yield of lump coal is important in practice because larger sizes of coal usually sell at higher prices. Some statistics published in England in 1934 (63) illustrate the economic origin of the interest in increasing yields of lump coal; these indicate for three sizes of coal that as the size decreases the value decreases in the approximate series 3:1.5:1, thus:"

May 1, 1940

Throughout the industrial world, Ilmenite, Rutile, Monazite and Zircon mineral sands play a KEY role in numerous industrial processes. Australia's ilmenites, rutiles, and synthetic rutiles are of vast importance in the world of titaniferous ores, and Australia has been the world leader in the field, and continues to adapt to new demands with alacrity. These materials enter a world titanium dioxide market that will exceed three million tonnes in 1990 at an expected growth rate of 2.3%. Many experts place current use in excess of 2.5 million tonnes of contained Ti02. Here we have a slide that illustrates projected growth rates in consumption, in SCM's view.

Jan 1, 1986

By A. A. Cochran

The objective of the research was to determine the final distribution of cerium additions to steel, their effect on sulfide inclusions, and the usefulness of radiotracer methods in investigating steel problems. Fifty-gram heats of steel were prepared that contained either cerium 141 and nonradioactive sulfur, or sulfur 35 and nonradioactive cerium. These steels were studied by autoradiography, measurements of their surface radioactivities, optical microscopy, and chemical analysis. Samples of the crucibles were analyzed quantitatively for cerium or sulfur by radioactivity counting methods. The addition of cerium to steel melts reduced the size and number of iron sulfide inclusions in the resulting steel. A significant fraction of the sulfur and most of the cerium penetrated into the MgO crucible during the melting operation, The cerium inclusions in steel were identified as cerium sulfide. Radiotracer methods were found to be versatile and highly sensitive.

Jan 1, 1963

By L. M. Dwarkin

Strip mining in Western Canada, though of considerable importance, is a fairly recent development for many of the operators in the district. Adding to the difficulty of unfamiliarity is the fact that a great deal of the stripping is done on pitching seams, for which the engineering and economic principles of setting the most advantageous strip ratio are not readily apparent. The novelty of the operation combined with the complexity of the principles involved can easily lead to misconceptions as to the determination of the economic ratio. Definition of Strip Ration There are two commonly accepted meanings of the term strip ratio: (1) The ratio of feet of overburden to be stripped per foot of coal recoverable. (2) The ratio of cubic yards of overburden per cubic yard or ton of coal. The first definition is inapplicable to pitching seams so, throughout this paper, strip ratio will be taken as the ratio of cubic yards of overburden to be removed per cubic yard of coal recoverable. Economic Ratio In the case of flat seams, the strip ratio is fixed by existing natural conditions, and the magnitude of this ratio determines whether stripping is economically feasible. With pitching seams, however, the strip ratio is a variable. On the outcrop, there is usually some coal which can be obtained with little or no stripping. As the work is carried down the pitch of the coal seam, the proportion of overburden continually increases until a point is reached where it is no longer economical to continue the operation. The question immediately arises as to the location of this point, and this resolves into the problem of determining the most favourable strip ratio, or, to use the accepted term, the economic ratio.

Jan 1, 1949