Search Documents

By P. Condori

Palabora Mining Copper (PMC) has two autogenous mills that have been in operation since 1976. The mills were originally designed to treat 30 000 t/d of open cast copper ore in a closed circuit with cyclones. As the ore body went deeper the open cast method of mining was changed to block caving, a consequence of this was the dolerite content (hardest barren material) increased significantly, increasing the production rate of pebbles and thus reducing the milling capacity. In order to cope with the increased ore hardness and to increase mill capacity, a second ball milling stage and pebble crushing were incorporated to the circuit. The above actions created new challenges to the circuit operation and bottlenecks in different areas of the milling circuit. This paper reports the holistic work performed on the Palabora autogenous milling circuit including the implementation of a mill constraint control scheme, the implementation of a pebble removal system from the circuit and a new circuit configuration. The achieved plant stability and increment of ore throughput are also reported in this paper.

Jan 1, 2012

By George Filz, Morales, Carlos, Bertero, Filippo Maria, Alessandro, Leoni

"The Deep Mixing Method (DMM) represents a viable solution to improve adverse geotechnical properties of foundation soils for many practical applications. A pre-construction soil investigation campaign is necessary to assess soil properties and to retrieve samples of different soil layers for a laboratory Bench Scale Testing program (BST). The BST has to be designed using various binder types, binder contents, and water/cement ratios in each of the soil types. Following the laboratory program, a full scale Field Test (FT) is typically necessary to verify the results of the BST. This paper will highlight the differences and the importance of performing both pre-construction laboratory tests and field tests to ascertain the proper mixing parameters in the different soil layers. Comparative analyses and interpretations between the lab and field stages, along with accumulated information about soil properties and quality control (QC) results, allow fine-tuning the production parameters throughout a project. Three Deep Mixing Method projects, where both laboratory and field tests were executed, are illustrated: (1) The LPV 111 Project (New Orleans, LA, USA): DMM was used for ground improvement/foundation strengthening to stabilize and support the burden of a new levee raise; (2) The Rio Puerto Nuevo Project (San Juan, PR, USA): DMM was applied to improve the soils adjacent to a 90"" forced sewer main relocation and to improve the soils for the base of a new drainage channel; and (3) State Road 83 (US 331) over Choctawhatchee Bay project (Walton County, FL, USA): DMM was applied to stabilize the causeway sections of the bridge enhancement project. Data recorded during laboratory and field tests for these projects were analyzed and interpreted to select the most appropriate construction parameters to provide a final high-quality product.INTRODUCTIONThe Deep Mixing Method (DMM) represents a viable solution to improve adverse geotechnical properties of foundation soils in many situations. The effectiveness of working parameters depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product.Generally a pre-construction soil investigation campaign has to be performed to assess soil properties and to retrieve samples of different soil layers for the laboratory Bench Scale Testing programme (BST). The BST has to be designed using various binder types, binder contents (or cement factors - CF), and grout water/cement ratios (W/C) in each of the soil types; the selection of the different combinations and dosages for the BST is based on past extensive experiences on similar materials. Following the laboratory programme results, a full scale Field Test (FT) has to be designed and executed, installing several DMM elements to verify the results of the BST and fine tune the construction parameters, with the appropriate binder type and dosage and the most effective equipment and tool configuration."

Jan 1, 2015

By Ken Mathers, Tom Conley, Jim Rozek

The Melbourne City Link Tunnels have been constructed through a BOOT process, the largest undertaking in Australia to date. Tolling commenced on the 1.6 kilometer Domain tunnel in April 2000, and the 3.4 kilometer Burnley tunnel December 2000. The project was delivered by design construct contracting and under ISO 9000. There were a number of major challenges in completing the tunnels, including much higher than expected groundwater infiltration, hydrostatic pressures greater than 6 bar, and unique design and construction applications required to prepare the tunnels for service. This paper covers the end play and final delivery of the tunnels.

Jan 1, 2001

By Edgar S. Rush

This study was conducted to make a limited evaluation of experimental and standard tractor dozer blades. A field test program was conducted in the southeastern part of Kansas on strip-mined areas where the spoil banks are parallel with rest-to-crest distances between 90 and 120 ft and maximum dozing distances usually less than 50 ft. This evaluation was a part of an overall joint Pittsburg and Midway Mining Company--U. S. Bureau of Mines (USBM) Specialized Reclamation Field Test Program primarily centered on the field t sting of experimental high-volume lateral relocation blades. The three blades evaluated were the 60-ft-wide angle (A) blade mounted on two 41B tractors. a 48-ft-wide A blade mounted on two D9H tractors, and a 13-ft-wide reclamation universal (Rec U) blade mounted on a D9H tractor. In addition to the experimental blades, three commercially available blades were tested: A 20-ft universal (U) blade mounted on two side-by-side (SxS) D9H tractors; a 20-ft U blade mounted on a 418 tractor; and a l2-ft straight (S) blade mounted on a D8H tractor. The dozer blade evaluations compared measured blade performance with soil and other site characteristics and with estimated earth-moving performance rates based on earthmoving methodology that accounts for the traction and speed of the tractor. The earthmoving methodology was also validated with data collected during this program.

Jan 1, 1978

By Robert Goldstein

A computer program for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. To provide a data base for these calculations, eleven 3-D machine models were prepared and the outputs of three luminaire types were measured. Calculations were done for thirty different configurations.

Jan 1, 1977

By Nelson Rivera

El presente texto analiza la crisis económica y su relación con el Banco Minero. Para ello, se revisa las dos últimas recesiones económicas que tuvo el Banco entre 1975 y 1982, donde la crisis se agudizó por una caída en los precios de los metales y una inflación de costos que no pudo ser transmitida al precio de venta. Como consecuencia de ello, las empresas mineras que tuvieron préstamos, acusaron pérdidas en sus ejercicios e incumplieron en el pago de sus obligaciones. Como medida anti-crisis, el Banco Minero estableció comisiones de alto nivel para evaluar las situaciones y recomendar la dación de dispositivos legales que permitieron asistir a los Pequeños y Medianos mineros en la restitución de liquidez mediante préstamos sobre liquidaciones a precios deprimidos, Asimismo, generó la consolidación, refinanciación y moratoria de los clientes que estaban en suspensión de pagos de las obligaciones contraídas con el Banco Minero y la creación de líneas de crédito especiales para la Pequeña Minería.

Mar 1, 1985

By Guo Gongyi

An extraction chromatography by which 99.99 % pure scandium oxide can be prepared from the starting materiel containing about 70% scandium oxide has been developed by taking advantage of some peculiar properties of the complex chemistry and extraction chemistry of scandium. The purification of scandium was performed at room temperature with relatively fast rates in two chromatographic columns. The preliminary separation of scandium from impurities was done by extraction chromatography using tri-butyl phosphate as the stationery phase in the presence of citric acid, and the nearly complete separation in the presence of perchloric acid. The scandium recovery was greater than 90 %.

Jan 1, 1989

By Alessandro Bertero, Dylan Pearson, Wesley Schmutzler, Matteo Bertoni

"The SR 83/US 331 highway is located in the Florida panhandle, where it connects the Walton County beaches to the I-10 corridor. The roadway is of vital importance to the economy of the area as well as its safety since it represents the primary hurricane evacuation route from southern Walton County. The Florida Department of Transportation (FDOT) decided to increase the number of traffic lanes from two to four and improve the geotechnical properties of the moderately deep, very loose foundation soils, that had affected the highway rideability for years. The soil mixing was selected as the method to meet the unique deep ground improvement challenges of the project. The design required that Shallow Mixing Method (SMM) be used to build a 10-foot thick platform that transferred axial load to the bottom soil layers through a series of Deep Mixing Method (DMM) columns. Upon completion over 8,300 SMM columns and 1,500 DMM columns had been installed, with no remedial work required. Also, only 1% of the almost 1,500 specimens tested did not meet the specification requirements. This paper will describe the challenges encountered and provide valuable information that may be useful for other future projects, including details not previously published.INTRODUCTIONThe counties of Walton and Okaloosa have been a very popular vacation destination for many ears. The 50-mile long coastline boasts beautiful, sugar-white beaches and waters the color of emeralds. The popularity of the area has been growing even further, over the last few years. A consequence of this phenomenon is a fast-paced increase of the traffic flow on the SR83/US331 highway, especially at the bridge that connects the Walton County beaches across Choctawhatchee Bay (Fig. 1) to the heavily traveled I-10 corridor. The highway plays a very important role for the area also as a commercial link and as the primary hurricane evacuation route from southern Walton County. The increase in traffic has produced higher travel time, when not a complete traffic paralysis, and exacerbated the issue of ground settlement where accelerated wearing of road foundation occurred due to the presence of very loose, moderately deep, soils, that had afflicted the highway for several years. The Florida Department of Transportation (FDOT) decided to put an end to these issues by increasing the number of traffic lanes from two to four and improving the geotechnical properties of the foundation soils. The Design-Build Maximum Price Request for Proposal (RFP) issued for the expansion of the Choctawhatchee Bay Bridge saw the participation of numerous D/B teams which produced various technical solutions. Among them, the FDOT selected the Skanska/Parsons Brinckerhoff (General Contractor) proposal which provided for the use of soil mixing as the ground improvement technology. The design/build team assigned Foundation & Geotechnical Engineering (Designer of Record) the ground improvement design which Treviicos South (Specialty Contractor) would execute."

Jan 1, 2017

By A. J. Williams

"Conventional base metal milling practice normally consists of crushing, grinding and cyclone classification followed by flotation. It is the authors' belief that the commencement of flotation after cyclone classification leads to inferior metallurgical results and that implementation of flotation of grinding mill discharges can result in increased recovery due to reduced overgrinding, reduced activation of contaminating minerals and improved dewatering circuit results due to the production of coarser concentrates.The concept of recovering minerals from the discharge of grinding mills is not new! Gold concentrators have utilized jigs and flotation cells while iron ore plants have employed magnetic separators to recover gold and magnetite respectively from the discharge of grinding mills. More recently, a Reichert cone has been used to recover sulphide and oxide base metal minerals from screened rod mill discharge. 1To the authors' knowledge, the first application of flotation of base metal minerals from the discharge of a production plant grinding mill was at the Lake Dufault concentrator of Corpor'1tion Falcon bridge Copper. Located 10 miles north of Noranda, Quebec the Lake Dufault concentrator commenced operations in August, 1964.The installation of flot11tion cells in the Lake Dufault grinding circuit proved so successful that an identical system was installed in the Manibridge concentrator of Falconbridge Nickel Mines Limited. Located 90 miles southwest of Thompson, Manitoba the Mamibridge concentrator commenced operations in June, 1971 and due to exhaustion of economic ore reserves discontinued production in May 1977."

Jan 1, 1984

Rosebery Mine is situated on the west coast of Tasmania and is AustraliaÆs largest volcanic-hosted base and precious metals deposit (zinc, lead, copper, gold and silver). The milling operation has been producing zinc, lead and copper concentrates continuously for over 100 years. RoseberyÆs long life demonstrates the operation to be high grade, and high margin, capable of operating through several commodity price cycles. Paradoxically, throughout this long history the ælife-of-mineÆ as defined by proven and probable reserves has been short. Zinifex has demonstrated its commitment to discover the future of Rosebery with the growth project æProject HorizonsÆ. The aim of the project is to extend the life of mine beyond 2020, with an additional exploration expenditure of $19 million over three years. Despite the maturity of the deposit, early success has confirmed the potential with the discovery of new resources. Mine planning strategic studies are challenging established paradigms of mine production, throughput rates and metal cut-off grades. Discovering the optimal process rate for Rosebery, by examining the æHill of ValueÆ and underground mine optimisation is proving critical to the best exploitation of RoseberyÆs rich resources. The promise of finding a mine within a mine is being realised, with new lenses being delivered by exploration success and real grade/tonnage options optimised through dynamic mine planning. The future of Rosebery is co-dependent on these two areas of discovery. This ensures capital expenditure decisions are informed, to secure the next 20 years of wealth creation and beyond.

Jan 1, 2008

By Bunting S. Crocker

PEBBLE grinding at Lake Shore is not a temporary wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct - 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 1 1/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to, $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change, back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1 1/4-in. steel ball charge. To change pebble size it is necessary only to change two sets-of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean. out the customary supply of grinding balls kept on hand. Also it has not always been ' possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant should be designed to use as many units-or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, .2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant. and an extremely efficient-one. In this plant the ratio of ball mills to tube mills was 1: 2. When the much cheaper pebble mills were substituted for the tube mills, this. ratio -was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was. proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on -.8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.1 This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without .grate discharges-both with 1 1/4-in. and 3/4-in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report' was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3 1/2-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are, lengthy and may be covered in a separate 'report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The -8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands .from the bowl sent to the primary pebble mills, see Fig: 1. In the pebble mill circuit the ore is ground to 90 pct -325 mesh (24 pct + 28 microns) In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO2, 80 pct insoluble. Its grindability at different. meshes has been shown near the top of 'the list in F. C. Bond's grindability tests' Lake Shore is not shown, but an adjacent-mine with identical ore, Wright-Hargreaves, is. Reasons for the-Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1952

By Dennis P. Martin, Michael M. Fitz, James E. Friant

Methods for reducing the cyclic nature of drill and blast tunneling operations have been long needed. A miniature blasting system using 10 mm (.375 in.) holes, 0.91 m (36 in.) deep, and blasting only one hole at a time makes it practical for men to work behind a shield, remaining at the face during the entire process. A prototype automated module was developed to drill, load the hole and initiate the detonation without moving from the hole. A unique cost effective gell explosive and a novel, low cost initiation method were developed.

Jan 1, 1989

By E. V. Daveler, Frank L. Antisell

CERTAIN physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface, and the "set," or the decail appearance of the surface of the shape. The set of the copper is, in a very large measure, directly related to the pitch; and so intimately are these characteristics connected that they are often used as synonymous terms by the refiner when he is speaking of well-refined copper. Oxygen is often spoken of as a medicine for copper, it being used to regulate the pitch.

Jan 1, 1920

By M Recabarren, A Echeverria, J Ronda, J I. Guzman, R Dodds, G Juarez, E Vila-Echague

A strategic mine plan is a fundamental part of any mining operation. It must provide a realistic and operative extraction and processing schedule, and yield the highest value for the business. For open pit mines, the problem can be modelled as a set of blocks representing the deposit, for each of which we need to decide if it is going to be mined, if so, when and where it will be sent (process, stock or dump).This problem can be proven to be of NP-Hard complexity. The traditional approach used by mining engineers to tackle this complexity is to separate the problem into more tractable components, solving each separately. The first step is to use the Lerchs-Grossman (LG) algorithm to obtain the final pit limit, as well as a set of optimised pit shells (nested pits), using different input prices. Then, using this input, operational phases are designed. Third, the set of phases can be used as an input for a phase-bench style optimisation, usually using a mathematical programming-based algorithm.There are, however, several problems with this approach. First, dividing the problem into simpler parts has the consequence that any compromises made at early stages limit the potential value left for the following steps. Second, LG is a static algorithm, with no concept of the time-value of money, capacity limits, opportunity costs, etc. Phase design is essentially a manual step, for which nested pits provide insufficient information in practice, and therefore the quality of the result in terms of potential net present value (NPV) depends strongly on the experience and expertise of the designer. This means that key input data such as commodity prices, different processes capacities and mine movement limits, are considered only at scheduling, when there is little room for optimisation. This sequential approach limits the potential value in each step, where a simplified problem is addressed, instead of addressing the real, and more complex problem, which is dynamic and should be solved as a whole.We present in this paper an algorithm, and its commercial software implementation, that addresses the dynamic problem as a whole, simultaneously and automatically creating a high-value strategic mine plan that adheres to basic operational constraints, determining dynamic cut-off grades and delivering a set of phases which can serve as a much stronger guide than nested pits for the final design. We discuss some of the key elements of the algorithm and propose a new methodology for strategic mine planning, where phase design dynamically responds to mining strategy definition. Results using different mining and operational parameters on a fictitious copper deposit are used as a demonstrative example.CITATION:Juarez, G, Dodds, R, Echeverria, A, Guzman, J I, Recabarren, M, Ronda, J and Vila-Echague, E, 2014. Open pit strategic mine planning with automatic phase generation, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 147–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Paul Hosford, Tim Haldane

"The paper describes the fast-track development of the project from feasibility study through to detailed design and construction, highlighting the process adaptations for handling sticky ore and water management in a tropical environment, and subsequent commissioning and operating experience of the mine. The paper discusses the geological setting, the environmental and socioeconomic considerations in developing and operating a mining operation in an underdeveloped country and the logistical challenges involved in bringing a large capital investment into Central America.INTRODUCTIONGlamis Gold Ltd. acquired the San Martin project in Honduras as a result of its merger with Mar-West Resources in late 1998. Despite the prevailing low gold price environment at the time of acquisition, Glamis anticipated rapid development of the San Martin project due to the quality of the deposit and other positive factors.Following favorable exploration and permitting activities in the first half of 1999, Glamis prepared a Feasibility study. In October 1999, Glamis decided to proceed with the development of the project and selected Hatch to provide the engineering, procurement and construction management services for the project. The San Martin project was in full-scale commercial operation approximately 14 months after the receipt of Board approval, and by July 2001 the San Martin project was operating at approximately 150% of its feasibility design capacity."

Jan 1, 2002

By C. Gasparrini

Mineralogy may be applied to the selection of appropriate separation techniques, as well as to assist in the evaluation of problems causing loss of metals and other economically important elements during plant processing. Mineralogic studies may thus help develop techniques to optimize metal recoveries. The present paper describes how such factors as the minerals in which the elements of interest are concentrated, their chemistry, the chemistry of the associated minerals, grain size and textural associations with other minerals in the ore, may affect decisions on separation techniques for the recovery of economic elements. A number of case studies are described in which the mineralogical observation of ore samples has revealed the cause of problems experienced in the extraction of select precious and base metals, or has been decisive in the choice of appropriate techniques for recovery.

Jan 1, 1981

By J F. Seale

The design of the settling pond for the Malvern Hills opencast coal project was based on a primary requirement to control runoff and sediment generated from the immediate 6 ha mine catchment, which included two seepages from old underground workings. The pond has been particularly effective in controlling turbidity in the outflow water, with the consent limit of 50 NTU being met on all but one occasion and normal levels of discharge less than 10 NTU. Water quality testing carried out at the time of consenting indicated that there were no acid-generation issues with the proposed mine site in dominant mudstone strata of the Broken River Formation, and that water from the old mine workings was near-neutral in terms of pH and well-buffered. However, it became apparent over the very dry summer of 2003 - 2004 that slaking of the exposed mudrocks in the mine batters was resulting in significant acidity generation, and outflow pH levels were well below the consent limit of 6.5 during and following periods of rainfall. Although these acidity problems have been remediated in the short-term by the use of lime products, it is clear that a programme of lithotype characterisation for AMD should have been undertaken and this has now been implemented. Design of long-term acid drainage control measures is being carried out, and will probably be based around the use of hydrated lime for pH control with enhancement of natural wetlands.

Jan 1, 2004

By S. H. Ash

THE MAGNITUDE of the anthracite industry's drainage problem in the Northern field of Pennsylvania is realized when it is known that, for the 8-year period 1944-51, all pumping plants in this region pumped an average volume of 112.5 billion gallons of water from the mines to the surface each year. This is over 214,000 gallons per minute pumped against an average hydrostatic head of 400 feet each year for that period (12).4 By comparison, Lake Wallenpaupack, the largest artificial body of water lying wholly in Pennsylvania, contains 71 billion gallons of water in its 24-square-mile area; the average volume of water pumped from the mines in the Northern field each year during the 8-year period was 58 percent more than the volume impounded in Lake Wallenpaupack. The natural configuration of the drainage area overlying the Northern field subdivides the total area into two major drainage areas-the Lackawanna River drainage area and the Susquehanna River drainage area overlying the Wyoming Basin. Although the 169-square-mile drainage area overlying the Wyoming Basin is slightly less than half that of the Lackawanna River drainage area (10), the total volume of water pumped to the surface from mines in the Wyoming Basin is 21 percent more than the total volume pumped to the surface from mines in the Lackawanna Basin. From this, it is apparent that the Susquehanna River and the pervious deposits in the buried valley over which it flows in its course across the coal measures of Wyoming Valley is the greatest single source of mine water affecting mines in this area. Because of its relatively flat terrain, the wide flood plain of Wyoming Valley does not facilitate rapid runoff; consequently, much of the surface water seeps directly into the buried-valley deposits and eventually into the mine workings.

Jan 1, 1953

By W. R. Clark, W. W. Cotter

Jan 1, 1946

By W. W. Cotter, W. R. Clark

Jan 1, 1946