Search Documents

Spirals have become one of the most popular methods for treating fine coal. Unfortunately, spirals tend to produce an undesirably high specific gravity cut-point and often misplace significant amounts of coal and/or rock. In the present study, a process-engineering tool known as linear circuit analysis was used to identify problems with traditional spiral circuits and to suggest alternative configurations. These analyses indicate that a modified rougher-cleaner circuit incorporating a middlings recycle stream offers the best option for improving performance while maintaining a reasonable circulating load. In light of this finding, a full-scale test circuit was installed and evaluated at an existing preparation plant. Data obtained from the plant tests indicate that the new spiral circuit can simultaneously reduce cut-point and improve separation efficiency. Preliminary economic analyses show that the new circuit provides an attractive payback on the capital investment.

Jan 1, 1998

By T. Tamagawa

A gaseous chlorination process for hydrometallurgical treatment of a chalcopyrite concentrate was investigated. The overall process is visualized to consist of low temperature chlorination-selective oxidation, followed by aqueous chloride leaching and SX-EW for producing electrolytic copper elemental sulfur and ferric oxide. In this article, the chlorination phase of the processes is described. Initially, the chlorination behavior of chalcopyrite-concentrate micro-pellets was investigated using a small batch-type fluidized bed reactor. The optimum conditions thereby established was used in continuous chlorination tests. The chlorinated products thus prepared were used in the selective oxidation phase of the investigation.

Jan 1, 1999

By C. J. Brown

Regeneration of hydrochloric acid steel pickle liquors has traditionally been accomplished by pyrohydrolysis. However, a number of factors have recently conspired to reduce the attractiveness of this approach. Moreover, the process is not amenable to small-scale operations. On the other hand, the standard technique for regeneration of sulfuric acid pickle liquors, which is the low-temperature crystallization of ferrous sulfate is applicable to any size operation. A similar technique has recently been developed to regenerate hydrochloric acid. Sulfuric acid is added to the ferrous chloride-bearing spent HCl pickle liquor. The temperature is then reduced to below 0°C, resulting in the crystallization of ferrous sulfate heptahydrate and liberation of free hydrochloric acid. Depending upon the crystallization temperature, variable concentrations of sulfate are left in the regenerated acid. Although this residual sulfate has an impact on the pickling characteristics of the regenerated acid, tests have shown that by adjusting the conditions, pickling rates will be at least equal to those using pure HCI, and an acceptable surface finish will be produced.

Jan 1, 2006

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 15,174-acre Sleeping Giant study area, including the 6,112-acre Wilderness Study Area (MT-075-111), in order to evaluate its identified mineral resources. The study area is located in Lewis and Clark County, MT, about 30 miles north of Helena. Sleeping Giant Mountain trends west-northwest from the Missouri to the eastern crest of Little Prickly Pear Canyon (the route of Interstate 15), and has several summits over 6,000 ft. Geologically, the area is in the Disturbed Belt, and a large block of Middle Precambrian metasedimentary siltstone and underlying shale has been thrust northeast over younger, sedimentdry volcanic and intrusive rocks.

Jan 1, 1988

By N. E. Norman

The big hole drilling industry is a relatively new one. In fact, very little big hole drilling was done prior to 1950. If there is to be a marriage between big hole drilling and mining, we should certainly take a look at the background of the big hole drilling industry. Let us examine the three main features of big hole drilling and determine how each applies to mining. Let's also look at the good qualities and the limitations of each of these character traits.

Jan 1, 1968

By Arne Landsberg

A study of the chlorination kinetics of germanium, silicon, iron, tungsten, molybdenum, columbium, and tantalum has been made to determine the effects of temperature, chlorine concentration, geometric surface area and gamma radiation. The reaction products were volatile at the temperatures used this making it possible to follow the reaction rates by weight loss of the solid. Chlorination rates of germanium, silicon, and iron were found to be directly proportional to chlorine concentration while the rates for tungsten, molybdenum, columbium, and tantalum were proportional to the 0.5 to 0.6 power of chlorine concentration. A good correlation of reaction rate and geometric surface areas was not obtained because the true surface area of the samples could not be measured. Intense gamma radiation had no effect on reaction rates. The Arrhenius activation energies determined over the temperatures used are as follows: Germanium, 27 kcal/mole (233°-241° C); silicon 33 kcaL/mole (375°-517° C); iron, cold rolled, 20 kcal/mGle (259°-325° C) annealed, 21 kcal/mole (293°-337° C); tungsten, 43 kcal/mole (617-776° C); molybdenum, 37 kcal/mole (445°-4910 C); columbium) 34 kcal/mole (229°?255° C); and tantalum, 29 kcal/mole (370°-449° C).

Jan 1, 1965

By Jr. Watts, B. K. Cantrell, K. L. Bickel, J. F. McDonald

"A field trial was conducted at an underground gold mine to evaluate diesel fuel derived from soybean oil (soy-methyl-esters or “biodiesel”) as an alternative to commercial, low-sulphur, number 2 diesel fuel (D2). A 2.7 m3, 18-ton load-haul-dump (LHD) unit, powered by a naturally aspirated, indirect injection (pre-chamber), 100 kW diesel engine was used as the test vehicle. The LHD was equipped with a diesel oxidation catalyst. The LHD operated satisfactorily on the biodiesel fuel. Operators observed a slight decrease in power and an absence of black smoke.Diesel particulate matter (DPM) concentrations were monitored for a six-week period while the LHD was operated with either the biodiesel fuel or the D2 fuel. DPM concentrations were measured in the mining section’s clean air intake, exhaust and on the LHD. Reduction in DPM emissions was determined from the measured difference in DPM concentrations between the clean air intake and the exhaust. The biodiesel fuel reduced energyspecific DPM emissions approximately 75%, from 3.6 ± 1.8 g/kW-hr to 0.86 ± 0.27 g/kWhr. Time-weighted average DPM exposure, measured near the LHD operator, was reduced from 0.67 ± 0.13 mg/sm3 to 0.28 ± 0.12 mg/sm3, or approximately 58%, when the biodiesel fuel was used. IntroductionDiesel exhaust consists of noxious gases and diesel particulate matter (DPM). Recent attention has focussed on the potential carcinogenicity of DPM and the potential health impact on miners. The National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as a “potential occupational carcinogen”, and that reductions in workplace exposure would reduce cancer risks (NIOSH, 1988). The International Agency for Research on Cancer (IARC) declared that “diesel engine exhaust is probably carcinogenic to humans” (IARC, 1989)."

Jan 1, 1997

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard to miners and mine operators. This type of failure, termed a "Cascading Pillar Failure" (CPF), occurs when one pillar in a mine layout fails transfering its load to neighboring pillars causing them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S. are documented. Mining engineers can limit the danger posed by these failures through improved mine design practices. Whether failure occurs in a slow, nonviolent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines, namely, the containment approach, the prevention approach, and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining.

Jan 1, 1996

By Thomas Novak, Philip Johnson, Richard L. Sanford, Lloyd A. Morley

Macintosh use in mine-planning applications lags DOS machines since many users have made significant investments in hardware and training for other environments. Macintosh use is becoming more pronounced in many other industries, and com soft-ware is of at least the quality of that available for DOS machines and many workstations. This paper describes attributes of the Macintosh computer family as related to many mine-planning problems and solutions including software, memory considerations, workstations, DOS compatibility, and networking.

Jan 1, 1993

By M. Fener, S. Kahraman, O. Gunaydin, M. Alber

Falling into the weak rocks category, fault breccias have extremely poor engineering properties. These pebbles typically cause issues with slopes, subterranean construction, and building projects. Professionals will benefit from the creation of some predictive models for fault breccia triaxial strength, as smooth specimen preparation is typically challenging and timeconsuming. The purpose of this study is to develop some predictive models for the differential stress (Δσ) based on physical and textural properties. Artificial neural networks were used to analyse data related to Misis fault breccia. Initially, models with moderate (noticeable, but not good) correlation coefficients were created using multiple regression analysis. After that, the regression models and three distinct artificial neuron network models were contrasted. Regression models are weaker and less trustworthy than artificial neuron network models, as demonstrated by this comparison. Pointed out is the practicality and ease of use of the artificial neuron network model with S-wave velocity and volumetric block proportion. Ultimately, it can be concluded that artificial neuron networks analysis provides a reliable indirect method for predicting the differential stress of Misis fault breccia.

Sep 1, 2025

By T. C. Davis

Nine organic derivatives of fluorine, silicon, boron, and aluminum were purified for thermodynamic studies using distillation, zone melting, and gas liquid chromatography, The unusual properties of these compounds required the development of special techniques for handling and purification. To determine purities of purified samples, new techniques for analyzing spectral data were developed.

Jan 1, 1965

By Chetan D. Savani, Mike K. Muchard

The necessity to evaluate undocumented foundation lengths is essential in assessing the useable life, need for scour protection, retrofitting, or full reuse of existing bridge foundations. For this purpose, Parallel Seismic Testing (PST) has the best accuracy and is applicable to the widest range of foundation configurations used in bridge construction of any test method. Although not limited to bridges, PST case studies are presented involving two bridges. To preface the case study discussions, an overview of the PST method is given along with its results and analysis thereof. In one of the cases, we were afforded the rare opportunity to see the existing piles being extracted long after the PST testing program was completed. The resulting Class A prediction reaffirms the accuracy of the method. Versatility of the PST method is also exemplified in the two cases presented, where unique situations from complex foundation systems were overcome by analysis to provide successful results.

Gold recovery from refractory ores can be very difficult and complicated depending on the causes of the refractoriness. Typically, a fine wind and/or the oxidation of the gold-bearing sulfide minerals are required to liberate gold from the host rock matrix. Mineral separation techniques, particularly surface¬wettability based separation (i.e., flotation) and magnetic separation, can be used to pre-concentrate the gold and sulfide minerals, or to remove mineral species that are harmful either to the oxidation of the gold-bearing sulfides or to the cyanidation following the oxidation. In this paper, several processes are described, including oil-agglomeration flotation recovery of fine-grained gold and sulfide, reverse flotation of carbonate minerals prior to pressure or bio oxidation, reverse flotation of elemental sulfur after pressure or bio oxidation but prior to cyanide leaching, and magnetic concentration of gold-bearing iron oxides. The integration of these techniques with gold hydrometallurgical processes may make the economic recovery of gold from an otherwise uneconomic refractory ore possible.

Jan 1, 2011

For over 50 years R W Miller & Co Pty Ltd operated old coal properties abandoned by former owners as uneconomic, some of which dated back to the last century. The companyÆs ability to survive with what were relatively poor quality coal resources required a small efficient management organisation. In 1970 R W Miller was involved in negotiations with other coal companies through coal sales contracts to develop private coal areas under the provisions of the old Coal Mining Act (1906) and these efforts led to the development of Lemington colliery. At the same time development of the Ironbark colliery holding near Newcastle commenced. In 1971, R W Miller approached the New South Wales Government for a resource replacement area to prospect for coal in the Upper Hunter Valley. Authorisation No 33 was finally granted on 30 September 1975, but the company found the area was inaccessible as most of the surface was owned by the Australian Army. Later R W Miller was granted Authorisation 66 of 2167.5 hectares at Mount Thorley near Singleton on 1 November 1976. The development of this coal mining project coincided with the second OPEC oil crisis in 1978 and a short-term boom for coal resources and the unrealistic expectations generated by the boom. This paper gives a broad outline of the development of the Mount Thorley project between 1976 to 1986 including the feasibility study and the many governmental and industrial delays that resulted in a three-year time overrun in the project development period.

Jan 1, 1998

By Kevin G. Stricklin

Introduction Continuous monitoring techniques have been used in the US and abroad for many years. A continuous miner has a monitor that measures methane and automatically gives a warning if the methane exceeds 1%. It deenergizes the continuous mining machine automatically at a maximum concentration of 2%. Main fans are also continually monitored to ensure operation. Alarms may also be given at a remote location should a fan slow or stop. The systems being developed can continuously monitor various gases and equipment throughout the mine and transmit pertinent data to a surface monitoring station. At this station, conditions throughout the mine can be monitored and, in some instances, controlled. These are known as Mine Wide Monitoring Systems (MWMS). History The use of environmental monitoring systems began in 1976 when a federal court approved the petition of modification to use belt air at the face. The first mine to receive a modification did install a system to supplement existing safeguards. Later, the Mine Safety and Health Administration (MSHA) and the US Bureau of Mines (USBM) conducted tests dealing with the use of belt air. Findings from these tests are being used to set guidelines as requirements of a petition. These requirements include: • Velocity of air has to be 0.25 to 1.5 m/sec (50 to 300 fpm); • Monitors will be installed at each belt drive and tailpiece and at intervals not to exceed 610 m (2000 ft); and • An alarm level of 10 ppm, above the ambient level is appropriate. The early uses of environmental monitoring could only be used outby the last open crosscut. That may be a reason for an initial slow growth of these systems. In June 1982, MSHA began evaluating systems that could be used in returns to ensure that monitoring systems being used in areas where permissible equipment is required does not of itself pose an explosion hazard. This is known as the Mine Wide Monitoring Systems Evaluations and Sensor Classification program. The evaluations and classifications granted are based on electric currents and voltages. Use of mine wide monitoring systems The environmental aspect of MWMS in today's coal industry deals with carbon monoxide (CO), methane (CH4), and air velocity. Just as all mines are different and encounter different problems, the MWMS are diverse and can be used to provide necessary data in all areas of coal mines. Mine operators in an ultragassy seam, for example, may be concerned with monitoring methane, while a mine that used diesel equipment may want to continuously monitor for diesel contaminants. In a mine with roof fall problems, airflow monitors may be helpful as an indication of whether the air is flowing in its normal course and at its normal volume. Today's MWMS can monitor any or all of these parameters. Most systems can be expanded as mining needs require. For example, a mine is now being monitored for methane and five years from now CO monitoring would help increase safety. It may be possible to use the same system by adding additional equipment. In the US, 30 environmental monitoring systems were installed from May 1985 through May 1986. In 1984 and 1985, there were 38 and 44 environmental monitoring systems in operation, respectively. Due to mine closings, 11 of these are no longer in use. However, the number of mines using environmental monitoring systems increased to 63. Use of these systems are not limited to any geographic area or

Jan 9, 1987

The Direct and Indirect Effects of the Reagent Suite on Froth Stability in Laboratory Scale Batch Flotation Tests

Sep 13, 2010

By Steven Gillgrass

Gerdau Monroe has installed and commissioned the Tallman Supersonic Carbon Injection system (TSCi™) for use in their 135-ton Electric Arc Furnace (EAF) located in Monroe, MI. TSCi™ is an innovative injection system with the primary aim of improving injection carbon delivery to the steel bath by increasing efficiency. It is proven technology with installations at numerous steelmaking facilities all over the world. Results from installation and commissioning of TSCi™ at Gerdau Monroe will be reported as well as on-going trials and optimization efforts. Standard injection systems deliver carbonaceous material from a vessel to the EAF using air where it is injected through a lance pipe or oxy-fuel burner. Using this method, material delivery to the EAF is limited by the pressure and velocity of the transport air. Loss of efficiency can be observed by looking at the quality of the injection carbon stream during operation or by measuring loss on ignition of EAF slag or off-gas system dust. TSCi™ uses a patented design and proprietary technology to improve delivery of carbonaceous material to the EAF. Using this method, savings at Gerdau Monroe were realized by reducing the amount of carbon used in each heat while maintaining or improving upon existing foamy slag practice. As well, significant savings were achieved as a result of reduced FeO content in the slag and improved recovery of iron. Additional savings can be realized by using a smaller mesh material to take advantage of lower material cost and higher injected surface area. Other inherent benefits to improved injection carbon include lower energy and electrode consumption, reduced refractory wear and reduced maintenance cost.

Oct 30, 2017

By F. C. Foshag, P. E. Wingrove

The Kayford, Boone and Nicholas Division of Bethlehem Mines Corp. operates a modern coal preparation plant in Van, WV. Since start-up of the Van plant in 1976 until the summer of 1980, the refuse handling system proved to be a costly maintenance problem and a material handling bottleneck. During the 1980 two-week miners' vacation, the original system - which included two screw conveyors and a drag conveyor - was replaced by an installation using two Flexowall steep angle belt conveyors. This paper describes the technical and economic analysis that led to the new installation and reviews its first year operating performance.

Jan 1, 1983

In order to deliver a quality shotcrete and concrete product underground for the extensions to the Cullinan Diamond Mine operations it was decided to develop a new, simpler concrete product to meet underground support requirements. The aim was to develop a concrete product that not only reduced costs but also met the performance criteria of the current range of concrete products used on Cullinan Diamond Mine, a 25, 45 and 60 MPa concrete and a fibre reinforced wet shotcrete. The concrete product batching and delivery system was to be from surface as opposed to the current underground batching systems. The operational principle was to include an automated surface batching plant with delivery of the concrete product to a borehole containing suspended pipelines delivering to an underground storage facility from where the product is delivered to the working area by further pumping or agicars. Keywords: concrete, shotcrete, full flow, frictional loss, pipeline transport, positive displacment pump

Jan 1, 2006

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016