Search Documents

By D. Harrington

A uniform hoisting-signal code for mines hoisting from more than one level, if adopted by all mining States, would be beneficial to employees and owners alike and should largely reduce the number of hoisting accidents. Misunderstood hoisting signals cause many shaft accidents involving injuries to men, damage to equipment, and loss of production from the resultant delay. Many of the metal-mining States have adopted codes for hoisting that are effective within the borders of that State but usually entirely different from the signal code, if any, in use in an adjoining State. For many years safety engineers have recognized this lack of uniformity as a distinct hazard, but a uniform code has never been adopted by the States or by the mining industry in those States that have not incorporated signal codes in their mining laws or mining regulations.

Jan 1, 1944

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, Hara, A. S. Kabir, R. Petrov

Manufacturing of thin sheet is difficult in industries. Some approaches, such as small-draft multi-pass rolling, intermediate annealing, isothermal rolling and high-speed rolling were proposed to overcome the deformability. In this study, different rolling speeds from 15 to 1000 m/min were employed to twin rolled cast AZ31B magnesium alloy to different reductions. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2014

By A. L. Jones

The subject assigned to me of "The Power" Problem of the Mine" is so broad that I have decided to confine myself to the question of the power supply itself, rather than the application of electricity throughout the property. We will look over certain economic aspects of the problem, particularly in the way it affects the mine manager or executive and his attitude toward the power plant. The accepted method of power application to the mine is by electric power, and the experience of each of you is that the job is never complete as you are always undertaking some further electrification which necessitates the stiffing up the power house to care for the additional load. The mine executive, then, is wrestling almost continuously with the problem of his power plant. Either it is overloaded and must be enlarged and rebuilt; or its operating costs are excessive; or it breaks down and limits coal output; or some one wants to sell new and improved machinery, until the manager almost hates the thought of such a restless part of his property. If he purchases power, every day new uses for it seems to be found. In many ways this unrest is due to short-sighted policy toward the problem, and the tendency when the problem of extension has to be met, to dispose of it in the cheapest way and without thought as to where the future is leading. The day when each opening had its own boiler plant, steam hoist, steam driven fans, steam pumps, steam loaders, etc., seems to be far behind us. The recognized method of power distribution today is by electric power, except for rather limited applications of compressed air; most of which is electrically compressed. During fifteen years contact with mines of Colorado and Wyoming the writer has seen nearly every mine power house double or triple in capacity or abandoned in favor of purchased power, worn. out and inefficient machinery thrown out, isolated boiler plants dropped, seam pumping at great depth changed to electric drive, all resulting in greatly reduced labor and fuel costs. Power costs, which in such isolated plants were considered normal, would be unthinkable today. One property where the main power supply was by compressed air from steam driven com¬pressors used under boilers 8.35 per cent of all the coal mined. The cost of power was 12 1/2 cents per ton of coal mined. Another property of four openings, each with its own boiler plant and usual equipment of hoists, pumps, etc., had a power cost of 10.3 cents for each ton mined; and these were days when you did not get very high prices for coal. Another property operating two mines mostly by steam used 11.1 per cent of the coal output under their own boilers and the power cost was 19.45 cents for each ton mined. Each of these properties is now electrified and power costs are from 3 to 4 cents per ton, and the fuel burned runs from 1 to 2 per cent of the output. With the broadening market and high prices for slack coal and the high prices for labor in boiler and engine rooms, the cost of steam is reaching a high figure, and efforts must be made to keep this down, by more efficient steam production and by utilizing this steam in better machinery which will increase the work done by each pound of steam. It must not be overlooked either, that the plant which is very wasteful of fuel is usually a pretty old one and one far from reliable. In a general way the more efficient the plant, the greater its reliability. Ample and reliable power supply means ability to get out coal when there is a market. The increasing use of purchased power is largely due to changing conditions which are tending constantly to push up the cost of power, unless the most efficient machinery is used and large scale production possible. The

Jan 1, 1923

By W. David Tyler

Any mining or engineering-construction excavation that extends below the water table must be dewatered. In many situations, the ground is of low permeability or the workings extend only a short distance below the water table. So water removal can be handled easily and economically by using mobile centrifugal pumps. However, there is an increasing number of mines that have a continuous high flow of water into the workings. Controlling this flow can significantly increase the cost of ore production. Successful implementation of any major dewatering scheme will ultimately rely on a clear understanding of the local geology. This understanding is necessary before an interpretation of ground water conditions can be made. It will dictate which dewatering methods are feasible. Once the geology and the ground water system are known, the scope and timing of the dewatering measures can be varied with the mine plan. Ground water modeling can assist in optimizing the dewatering system, though the precise objective of each model should be clearly defined. Production wells must be sited and drilled so that individual well efficiencies are high. Any lost efficiencies will translate into higher operating costs. Each well must be designed for maximum long-term control of the water table, and pumps sized to operate under continually changing heads. Finally, the investment in each production well must be protected during the mining process.

Jan 1, 1991

By Lowell T. Harmison

I appreciate very much the invitation to speak with you and the opportunity of bringing you messages from both the Secretary of the Department of Health and Human Services and the Assistant Secretary for Health/Acting Surgeon General of the U.S. Public Health Service. I would like to take this opportunity to congratulate you (the organizers of this Conference) on identifying the critical issues in the field and assembling such a broad array of experts to address them. I would like to present a brief view of the emerging framework for health that puts into perspective some of the aspirations of the Administration and to highlight several points with regard to prevention and occupational health. The goals are: 1. To improve the overall health status of our people. (This has been and will remain the National policy regarding health.); 2. To engage the Nation in the important effort of enhancing public health. (This is not reserved exclusively for the activity of the Federal Government or for State Governments. Public health has to be a cooperative effort that brings together all of the people engaged in the process of serving the people.); and 3. To pledge that health care will not be priced out of anyone's reach because of inflation. (It is clear that there are major tasks of bringing about economic recovery in our country. One aspect of this effort is to guard against the cost of health care not being allowed to rise beyond the reach of persons who need that care.) "How will these goals be achieved and what must change in the delivery of health and medical care in our society?" There are a number of real issues as well as perceptions that adversely affect the attainment of these goals: First, The cost of medical care is soaring and the public, industry unions and other elements of our society are becoming concerned. (They recognize the problem and are demanding a solution.); Second, There is a growing concern about the priorities that have been set. (For example, the evidence that preventive interventions are the most effective approach is overwhelming, yet medicine has not yet given that a high priority.); and Third, There is the perception that physicians do too much to too many people at too great a cost and that too much and too costly technologies are used. In view of the perceptions, we all must accept some changes and the challenges that needed changes will bring. A month before the new budget went to Congress, President Reagan went on nationwide television and told the American people that, "It is time to recognize that we have come to a turning point and we are threatened with an economic calamity of tremendous proportion and the [old business as usual treatment can't save us. Together we must chart a new course]." Now eight months down the road from this and a long Spring and Summer of discussion both within the Executive Branch and in the Congress, many plans and programs and concepts have emerged. The new course has been charted and the turning point has been made. Business as usual has been put aside and the Administration's leadership has been stretched and tested in putting forth a better approach with the reality that money is tight and that old habits of delivering care are difficult to change. The Congress has now given us a look at a new health budget that takes into account some of the harsh economic realities and that does make allowances for the persistence of familiar behavior. Against this background, it is now possible to begin addressing ways to provide health services to people at a price the Nation can afford to pay. There are without question difficult decisions involved but the Administration is committed to supporting and improving health care in America. It has been the President's contention that one of the principal causes of the inflationary spiral in the country was the steady and indefensible growth of the Federal budget. The problem stems from the fact that we have been living well, but beyond our means for nearly 30 years. Now we are discovering that there is a bottom to the barrel after all. It is possible for our society to run out of things like energy (oil), water or money. The health bills must be paid -- by Government, by insurance, by parents or by someone. Each year with a bigger shopping list and more money to spend the Federal Government went into the marketplace to buy. This action altered the

Jan 1, 1981

By Andrew J. Petruska, Rik Banerjee

This study explores implementing a machine learningbased system to generate a 3D surface repre- sentation of the roof and support straps in the mine. Event cameras have been chosen for their performance in high-dynamic-range lighting conditions and for their low latency. To enable automated drilling and bolting, 3D vision using eventbased cameras has been developed. A ground-truth set is created using two, time-synced event cameras and a LiDAR camera. These sensors are used to construct a ground-truth dataset of corresponding event- camera images and surface maps from the LiDAR. The network is tested with stereopairs of event images and produces a depth image with ±5 mm RMS error on average across 1000 test images.

Feb 1, 2024

By A. W. Fletcher

A nickel-copper sulphide concentrate was treated in a pilot plant at Warren Spring Laboratory during 1961, by a hydrometallurgical roast-leach- solvent extraction process devised to cleanly separate the metal values, and produce acid sulphate liquors containing the metals. It is shown that 86 percent of the nickel and 95 percent of the copper could be leached from the calcine, after a sulphatizing roast on finely ground flotation concentrate. Iron was removed from the leach liquor by limestone neutralization with a small loss of values. Copper and nickel were separated by solvent extraction with naphthenic acid in kerosene after partial neutralization of the iron-free liquors with ammonium hydroxide. Hydrogen sulphide and chlorine were used to remove zinc (and residual copper) and cobalt impurities respectively. The recovery of pure copper and pure nickel, by electrowinning, from the acidic solvent extract strip liquors finally produced, appears technically feasible.

Jan 1, 1964

By P Kittler

In the spectrum of mining-related disciplines, geometallurgy sits between resource geology and metallurgical engineering. Unlike its neighbours, it is a relatively young discipline and its concepts, procedures and techniques are still evolving. Relevant geometallurgical issues differ from one deposit to the next so there is no single template that can be used in all situations, meaning that geometallurgy programs are nearly always customised and tailored to the deposit and the situation.Over time, a number of key mistakes are seen to emerge regularly. The eventual impact of these mistakes can vary from suboptimal performance of mine and plant to complete failure of the operation. For instance, poor characterisation of ore lithologies and their spatial distribution can have negative impacts on processing plant throughput. However, when combined with failure to identify critical blending constraints it can result in a totally inoperable plant.A number of common mistakes committed during geometallurgical programs are discussed and some preferred alternative approaches are suggested

Sep 5, 2011

By M I. Pownceby, M A. Rhamdhani, W J. Rankin, G Brooks, I R. Ignacio

Steelmaking has a significant contribution in producing greenhouse gases and there is a worldwide push towards decarbonising the process. One of the approaches to reduce CO2 emissions is to use hydrogen in the blast furnace (BF) as the reductant gas. However, hydrogen reduction is an endothermic reaction, bringing changes to the temperature distribution in the BF. Understanding iron ore sinter mineralogy and reducibility under a hydrogen atmosphere is essential to optimise the process. In this study, sinter analogues in the Fe3O4-CaO-SiO2 (FCS) ternary system together with industrial sinters were reduced in H2-rich and CO atmospheres and the resulting reducibility and associated mineralogical changes were observed. Results show that magnetite-lime-silica (MLS) sinter analogues had similar reduction rates under H2 and CO, and also higher reducibility than most of the industrial sinters, suggesting that magnetite sinters could be used efficiently in a conventional or hydrogen blast furnace.

Sep 18, 2023

By E. Ilgar

"Deposition studies were conducted in acid copper electrolyte to determine the influence of chloride ions on cathode morphology. A statistically designed screening test was carried out in the absence and presence of 20 ppm CI- using a three factor, two level factorial design, in an electrolyte containing 36 gl'! Cu2+ and 150 gl-! H2S04, The independent variables evaluated were agitation; current density and temperature and their influence on surface roughness was determined. The copper deposited at current densities where activation was the primary control mechanism appeared similar in morphology whether stirring was used or not. The addition of 20 ppm CI- to the electrolyte gave rougher deposits under the same conditions. In the mixed control regions, considerably rougher, dendritic deposits were obtained when CI- was present. Agitation was effective in reducing the copper surface roughness both in the apparent activation and mixed control regions in the presence ofCI-. The results of this study showed that 20 ppm Cl- polarized the copper deposition at low overpotentials but caused depolarization at higher overpotentials.IntroductionChloride ion is inherently present in copper electrolyte, either as an additive or from other sources such as make up water. The behavior of the chloride ion is well documented in electrorefining operations, but its role in copper winning is less obvious. However in both cases there is evidence that cathode growth and solution chemistry are strongly influenced by its presence. The mechanism and electrochemical action of the Cl"" have been shown to be very complex, therefore a better understanding of its influence on electrocrystallization is essential for improved cathode deposit growth control. It was proposed that Cl"" polarizes the copper deposition reaction at low concentrations due to CuCI formation but depolarization occurs at higher concentrations due to the formation of a soluble CuCI2"" complex [1,2]. Franklin [3] reviewed the mechanism of additives in the electrodeposition process and proposed that the Cl"" complexed with copper, adsorbed on the cathode as an induced anion leading to an increase in the reduction rate. At cathodic overpotentials less than 100 mY, lppm NaCl had a polarizing effect, i.e. an increase in impedance of the charge transfer step. At higher Cl"" concentrations up to 100 ppm, depolarization occurred as evidenced by a decrease in impedance, which was attributed to soluble cuprous complexes [4]."

Jan 1, 1997

By R. W. Smith, S. H. Ash

Marked progress in safety has characterized the operation of coal mines in general in the State of Washington during the 5- year period 1928-1932 , particularly during the years 1931 and 1932. Physical conditions such as steep pitches , inherently bad roof and floor , prevalence of gas , and explosibility of the dust of Washington coals present certain definite hazards . Although advances have been made in accident reduction in Washington , the State still has far to go in that direction . The State has endeavored to reduce its coal -mine accidents by the usual method of making certain definite safety requirements mandatory . The value of education has not been underrated , but the educational method used has not altogether achieved the res lts desired by the industry itself , particularly within certain imdividual organizations . The past 2 years have witnessed a growth , in certain instances , of the essential ideas that the observance of safety precautions on the part of all is demanded if accidents are to be reduced , and that the initiating and carrying out of any program to promote and obtain desired results in accident elimination must begin and function from the top downward . Mining operations of Washington mines have been described in various publications of the United States Bureau of Mines .

Jun 1, 1933

By Rafael C. Castro, Paul V. Savard, Kathleen M. Murtagh

Preliminary design is underway for the Massachusetts Water Resources Authority’s (MWRA) next major tunnel program, the Metropolitan Water Tunnel Program (MWTP). The MWTP is the latest part of MWRA’s ongoing efforts to achieve redundancy for its metropolitan water transmission system including its historic deep rock City Tunnel, City Tunnel Extension and Dorchester Tunnels. The MWTP comprises several deep rock tunnels that will be approximately 10-foot to 12-foot finished diameter totaling just over fourteen miles long and ten connections to existing large diameter surface piping and pumping stations. This paper will present an update on current engineering and permitting efforts, packaging schemes, and the schedule to complete the MWTP.

Jun 13, 2023

By D. F. Malan, M. Grave, J. A. L. Napier

Previous fundamental research projects have indicated the value of continuous closure measurements in deep tabular excavations for improved support design, hazard assessment and for quantifying the effect of seismicity on stope closure. This paper describes further measurements in a VCR stope to validate some of the earlier findings. Calculation of the closure ratio showed that it is a good measure to identify different ground conditions and possible hazards. This work was supported by numerical modelling results, which showed that the closure ratio is very useful in discriminating the response of different geotechnical environments. Des projets précédents de recherche fondamentale ont démontré la valeur de mesures continues de fermeture dans le cas de profondes excavations tabulaires pour une conception améliorée du soutien, de l’évaluation du danger et pour quantifier l’effet de la séismicité sur l'affaissement du toit d’un chantier d’abattage. Le présent document décrit d’autres mesures dans un chantier d’abattage VCR afin de valider certaines des conclusions précédemment formulées. Le calcul du degré d'affaissement montre qu’il y va de soi d’identifier différentes conditions de sol ainsi que les dangers possibles. Les présents travaux ont été confirmés par des résultats de modélisation numérique, lesquels ont démontré que le taux d'affaissement est très utile quant à discerner la réponse dans des environnements géotechniques différents. Vorherige Forschungsprojekte haben den Wert von kontinuierlichen Setzungsmessungen im tiefen Sudafrikanischen Strebabbau angedeutet, vor allem fur Ausbaudesign und Risikobewertung, als auch fur die quantitative Bestimmungen der seismizitatsabhangigen Setzung. Dieses Referat beschreibt weitere Messungen in einer VCR Grube um fruhere Bestimmungen zu bewerten. Dass errechnete Konvergenzverhaltniss erweiste sich als eine gute Massnahme zur bestimmung von geotechnischen Zonen und moglichen Risiken. Numerische Analyse unterstutzte die vorliegende Arbeit und deutete darauf, dass das Konvergenzverhaltniss sehr brauchbar ist um Verhaltensunterschiede der geotechnischen Zonen zu erproben

Jan 1, 2003

By S. H. Ash

Introduction Probably the newest thing in mining safety is the apparent dissatisfaction on the part of the mineral industry, as represented by both management and labour, and the general public of many nations in which mining is conducted, with the safety record of the mining industry. This is reflected by published comments in the technical press;' in labour periodicals, in popular Journals and periodicals, and in the daily press (5, 11). Despite what may be said to the contrary, mining in the United States is becoming safer, and this trend has been evident for several years (see Figures 1 to 4). Because the author's experience has been mostly in the United States this paper will discuss briefly some recent observations in the United States that have a bearing on mining safety. Because coal mining is of primary interest to the Mining Society of Nova Scotia, the paper treats mostly of coal-mining safety; however, many hazards in mining .are common to all mines, regardless of the minerals mined.

Jan 1, 1950

By J. M. Barker

The concept of global-market access through transportation efficiency is a concept whose time has come. The basis of this approach is customer satisfaction—the higher the better. But beyond what seems almost too logical is the question of how to achieve this market access. All industrial mineral exporters face stiff competition. Factors include proximity of competitive industrial minerals and substitutes, pricing pressure, political and cultural differences, currency fluctuations, communication problems, trade finance restrictions, and transportation imbalances. The following discussion will focus on transportation activities in global competitiveness, but the producer with the larger offering of services will often make the sale, not necessarily the low-cost producer (Cook, 2002). Some key concepts for global-market access are “the market concept,” just-in-time delivery, quality retention, and global customer service.

Jan 1, 2003

By Rodney L. Stone, David S. Cahn

As part of an over-all laboratory and plant test program to determine mixing ad other techniques for a more economic use of bentonite as an iron ore pellet binder, a settling test for measuring the bentonite content within a pellet or a batch of pellets has been developed. Through this test, it has been shown that dry fracture load is directly proportional to bentonite content in batches of pellets, but inversely propor tional to bentonite content in individual pellets of the same batch. This apparent paradox is explained by a negative correlation between a pellet's size and its bentonite content and the fact that large pellets can withstand a higher fracture load than small pellets. In past attempts to characterize green and dry iron ore pellets, the authors found large variations in the results of strength tests on closely sized pellets from the same batch.' Reasons advanced for such variations in the quality of pellets in which the binder is bentonite were the presence of internal flaws and the nonuniform distribution of the binder. Even when resulting pellet strength is good, there is still the question of whether the same strength could have been attained through a more effective use of a smaller amount of bentonite. The authors' own and other studies 2-3 have pointed out the strong dependence of pellet strength on the degree of "mixedness" of the iron ore concentrate and the bentonite binder. However, before such a relationship could serve as a guide for the development of better mixing techniques and the associated economy of

Jan 1, 1969

By Charles Vaught, Kathleen M. Kowalski

Safety and health professionals from all sectors of industry recognize that training is a critical element of an effective safety and health program. A major concern in the mining industry is how to train both an aging workforce and the expected influx of new miners and mine managers as older workers retire. Thus, a review of some of the basic principles of adult learning may be helpful to mine trainers. This paper discusses the principles of adult learning based on research in education and psychology. It stresses the importance of taking a systems approach to training, focusing on the relationship between the environment and technology, and understanding how workers interact with both. The authors argue that the principles of adult learning and a systems approach are fundamental to the delivery of effective training in the mining industry. Examples of training programs developed by the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health are presented within two broad performance domains: routine and nonroutine skills. Basics of curriculum development are also briefly presented to provide the mine trainer with a template for program development.

Jan 1, 2002

By C. J. Cajka

Commodity agreements, trade liberalization, producer cartels, the New International Economic Order, price stabilization and access to supply are buzz words of the day. The international concern and dialogue on these concepts, often by a new breed of politically motivated experts, have generated intense interest in seeking an international solution to natural resource problems. While this momentum was maintained during the past year, the growing incidence of protectionist actions by several major nations has been eroding confidence in the global approach. The seriousness of current difficulties has created an urgent need for decisive action. At the same time, the limitations of the global approach have become more evident.

Jan 1, 1978

By von Wielligh. L., D. G. Hattingh, M. N. James, W. Thomas

"SynopsisThe process of joining materials by friction is based on generating the heat necessary to create a solid-state mechanical bond between two faying surfaces to be joined. In simple terms, the components to be joined are subjected to frictional heating between rubbing surfaces, causing an increase in interface temperature and leading to localized softening of interface material, creating what is described as a ’third body’ plasticized layer. This plasticized zone reduces the energy input rate from frictional heating and hence prevents macroscopic melting. The plasticized layer can no longer transmit sufficient stress as it effectively behaves as a lubricant (Boldyrev and Voinov, 1980; Godet, 1984; Singer, 1998; Suery, Blandin, and Dendievel, 1994). The potential for this solid-state frictional joining process to create high-performance joints between, for example, dissimilar materials with limited detrimental metallurgical impact, and reduced defect population and residual stress level, has had a very significant impact on fabrication and repair in industrial sectors such as transport. This paper presents a brief overview of the advances made within the family of friction processing technologies that could potentially be exploited in the nuclear industry as alternative joining and repair techniques to fusion welding.Modern friction processing technologies can be placed into two main categories: those that make use of a consumable tool to achieve the intended repair or joint (friction stud and friction hydro-pillar processing) and those making use of a non-consumable tool (friction stir welding). The most mature friction joining technology is friction rotary welding, where a joint is formed between original parent materials only. A new addition in this category is linear friction welding, which opens the potential for joining complex near-net-shape geometries by friction heating. The continuous innovation in friction processing over the last 25 years has led to the development of a number of unique processes and applications, highlighting the adaptability of friction processes for specialized applications for high-value engineering components.IntroductionAssessing the potential for using alternative joining and repair techniques for specific applications in a given industrial sector is informed by an appreciation of the current size and potential growth in that sector. Power generation by nuclear fission has been out of favour over the past few years, due to several high-profile nuclear incidents, e.g. the Fukushima Daiichi nuclear disaster, as well as concerns over disposal of nuclear waste and spent fuel rods. However, due to rapid increases in the demand for electricity, coupled with many fossil-fuel fired plants reaching end-of-life, there is renewed interest in installing additional nuclear capacity."

Jan 1, 2015

By Ronald L. Wiegel

In the 2000 page Handbook of Mineral Dressing by A. F. Taggart, the subject of material or metallurgical balances is covered in only six pages of eve-straining type. Although Taggart's work was compiled before 1945, and there has been significant progress since then in most areas of mineral processing, the practicing metallurgist's approach to metallurgical balances remains exactly the same as described in those six pages. There are several portions of Taggart's text appropriate to introduce the subject of this paper which I would like to quote: "Milling Calculations. Computations of per¬formance in milling are complicated by the fact that it is a continuous rather than a batch operation, that the quantities of solid materials handled are large and usually mixed with water, hence difficult or impos¬sible to weigh. Fortunately it is possible to determine many facts concerning perfor¬mance without knowing weights, if the value of various constituents is known in some common unit, e.g., the content of some par¬ticular metal or mineral, or of water, or some ingredient soluble therein, or of par¬ticles of a particular size or falling within some particular size range, or the like."

Jan 1, 1979