Search Documents

The Sams Creek gold deposit near Takaka in northwest Nelson was discovered in 1974 by CRA Exploration (CRAE) geologists. CRAE recognised the potential of the area and subsequently undertook a comprehensive exploration programme of geological mapping, soil and rock-chip sampling, geophysical surveys and diamond drilling. Exploration defined sporadic gold mineralisation contained entirely within a deformed and hydrothermally altered, peralkaline granite porphyry dyke with a seven kilometre strike length, and up to 60 m thickness. Rock chip samples indicated extensive and economically significant gold grades over approximately one kilometre strike of the dyke at Main Zone prospect. CRAE completed 30 diamond drill holes at this prospect and defined a limited resource. Oceana Gold Limited recommenced active exploration at the Sams Creek Project in late 2002, focusing on improving the geological understanding and known resource at Main Zone. Completion of 1041 m diamond drilling successfully increased the estimated resource to 10.7 Mt @ 2.12 g/t Au containing 729 000 oz at a 0.7 g/t cut off. A further campaign of 1560 m diamond drilling was undertaken in 2003 - 2004 to extend the resource and test the continuity of high grade mineralised zones. Deeper intersections of the porphyry dyke indicated geometrical complexity and grade variability similar to that observed at shallow levels. Recent research suggests that Sams Creek can be geologically classified as a variant of intrusion-related gold systems, and therefore comparable to some other, very large gold deposits. However, due to the rugged terrain and dyke geometry, surface drilling is reaching the limits of viability at Main Zone. If infill drilling continues to be successful then an underground decline may be developed to facilitate further exploration. Potential also exists along strike, where other significant gold anomalies are known but largely untested by drilling.

Jan 1, 2004

By E. Marè, D. R. Groot, R. Engelbrecht, T. Coetsee

Hydrogen peroxide is often used as an oxidising agent in experimental waste electronic equipment (WEE) leaching work. However, the high cost of peroxide is a negative factor in its consideration in further process development. A few studies have reported on the efficient application of peroxide addition schedules to ensure optimum reagent consumption. Large quantities of unleached substrate material contained in WEE feed material result in a large dead volume of material in the leaching reactor. This factor necessitates fast reaction rates to enable the use of a high feed material throughput reactor to enhance overall project viability via hydrometallurgical processing. In this study the effects of hydrogen peroxide addition schedules on base metal leaching efficiency and solution temperatures were tested at laboratory scale. The results showed that overall peroxide consumption can be optimised to lower levels by matching peroxide additions to the particular feed material’s leaching behaviour. A simplified integrated model for peroxide decomposition is used to explain its effect on solution temperatures and leaching rates. Keywords: Peroxide consumption, waste electronic equipment, copper leaching, integrated model

Jan 1, 2020

By Thomas P. Mucho

Retreat or pillar recovery mining redistributes the overburden weight onto the adjacent coal pillars in a room-and-pillar section. The additional stress and the resultant energy stored in the remaining pillars can become so great that pillars may bump or violently fail. An investigation at the Gary No.2 Mine was conducted to examine the effectiveness of the thin pillar mining method for mitigating bump occurrences. Field observations were made and instruments were installed to monitor pillar behavior during extraction. Stress monitoring instruments and roof-to-floor convergence stations were installed in pillars and entries and crosscuts, respectively. Results indicated that high pillar stress concentrations occurred in these bump-prone geologic conditions. The thin pillar mechanism, the creation and progressive outby movement of an expanded yield zone, was also monitored through the instruments. The expanded yield zone, a result of using thin pillars in a highly stressed pillar line area, mitigates bump risk.

Jan 1, 2010

By Reeves M

A review of the literature available in English on kriging and geostatistics is given with the references cross-classified by their subject matter for convenience and ease of use.

Jan 1, 1979

By Y. Z. Zhang

Cyanide has generated environmental concerns because of its toxicity, and it may not respond to the treatment of complex and refractory gold ores. Gold leaching by thiourea is one of the most promising substitutes of cyanide. However, the high reagent consumption has hindered thiourea from its commercial application in gold extraction. The process chemistry and mechanism of thiourea degradation has been discussed on the basis of chemical bonding theory, thermodynamics and electrochemistry in this paper. Progresses on the decreasing of thiourea consumption have been summarised. The potential application of thiourea in gold extraction has been evaluated.

Jan 1, 1996

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. This project is concerned with the determination of the effects of operating variables on the reaction of the particles. Experiments were carried out in a large laboratory-scale flash furnace with 72 wt-% Cu matte by varying initial particle size, temperature, oxygen partial pressure, oxygen-to-matte mass ratio and residence time. Chemical analysis was used to study the oxidation extent and copper volatilization. Particle fragmentation was examined. Fractional conversion and sulfur removal slightly decreased with initial particle size, while a higher oxygen-to-matte mass ratio mainly resulted in higher fractional conversion and more efficient sulfur removal. The fractional conversion values represented the overall extent of oxidation more closely than degree of sulfur removal.

Jan 1, 1997

By M. Gorman

The Mineral Park Mine is an open pit copper-molybdenum mine located in northwestern Arizona, approximately 74 miles southeast of Las Vegas, Nevada. The property has been owned by the Duval Corporation, Cyprus Mining Company and Equatorial Mining of Australia. Mercator purchased Mineral Park from Equatorial in 2003. Mineral Park commissioned a 25,000 tpd copper and molybdenum concentrator in November and December of 2008. The process includes two stage milling (SAG and Two Ball Mills) fed by primary crushed ore. Metals are recovered in a copper-molybdenum flotation circuit consisting of mechanically agitated roughers and cleaners. The copper- molybdenum flotation concentrate is thickened and further processed in the molybdenum flotation circuit which separates the copper and molybdenum minerals into salable concentrates. The molybdenum circuit also uses mechanically agitated cells. This paper describes the plant and some of the highlights of the commissioning process.

Jan 1, 2010

By María Eugenia Castro, Silvia Galasso, Jorge Duca, Claudia Osuna, Ernesto Esparza

"We present a procedure for treatment of non-active solutions equivalent to the solutions obtained from dissolution of ionic exchange resins used in purification of a nuclear reactor primary cooling system containing Co, Ni, Cs and its isotropic varieties as main radioactivity source. Finally it is immobilized into a ferritic matrix by calcination which avoids its future leaching into environment.In order to achieve the objective of this treatment, a bivalent and a trivalent iron salt is added to the solution. Then, either a base or an acid is added, depending on the initial pH of the treated solution, with a Cs precipitating additive in order to reduce Co and Cs by precipitation, flocculation and adsorption. Controlling the amount of precipitating reactives it is possible to modify the activity/volume rate becoming a medium into a low radioactivity waste.The leaching test result applied over the ferritic sample is lower than the minimum limit established by law. Therefore, it can be kept safely in a interim storage."

Jan 1, 2008

By W. K. Connor, O&apos

Thermal Treatment Technology Division Albany Research Center, U.S. Dept. of Energy Oregon. This evaluation included a characterization study and direct smelting tests conducted in a bench-scale electric arc furnace (EAF). In contrast to other thermal treatment technologies considered for these wastes (i.e., fluidized bed combustion), direct smelting in the EAF can process 100% of the wastes without prior beneficiation, and utilizes solid oxidant additions (in this case iron ore) rather than air to oxidize the carbon. This solid oxidant addition is advantageous because it results in the production of several value-added furnace products. These products include cast iron resulting from the reduction of the iron oxides, baghouse dust containing virtually all of the zinc from the residues, and a clean (nonhazardous) slag product suitable for recycle as concrete aggregate or construction fill. Offgas from the smelting furnace also holds potential as fuel gas for cogeneration. The direct smelting tests conducted thus far were successful at producing the desired furnace products, exhibiting the potential for complete recycle of the waste pile. A cast iron product of comparable quality to conventional cast irons was produced, at nearly 80% iron recovery to the metal. The slag product was determined to be nonhazardous, based on the EPA TCLP. Lead and zinc partitioning to the dust product was greater than 99%. The material balance over the furnace indicates that for every ton of feed processed, 540 lb. of cast iron, 600 lb. of slag, and 150 lb. of dust would be produced. Energy consumption was roughly 1.10 kWxh/lb of feed material. Prior experience suggests that these figures measured in the bench-scale furnace would translate to 0040 to 0.50 kWxh/lb at the industrial-scale.

Jan 1, 2000

By Thomas Weyand, Thomas Claridge, Dale Nickels

"This paper addresses the initial results of a project to evaluate the suitability of copper mining tailings as raw material for the production of structural products using PMET’s patented technology. Preliminary testing indicated that high performance structural products were possible using these materials. A demonstration scale project produced approximately 1,500 bricks in various colors. These products fall under under ASTM C- 73 and were found to present properties suitable for severe weather applications. Although the products in this project were of typical brick dimensions, other products are possible, for example concrete block substitutes or pavers. These products from the PMET process are commercially known as Brixx. This paper will provide operational details of the production process, mineralogy and mechanical properties of the products.INTRODUCTIONPMET has developed process technology that can convert various siliceous waste materials into competent structural products. This technology is the subject of US patent # 6,068,803. In general, the process consists of mixing lime, water and the major feed stock, pressing to form a “green” shape, and curing the product in an autoclave for 6 hours with saturated steam at ~200oC. The curing process forms Tobermorite, which acts as a crystalline binder. Freeport-McMoRan approached PMET to see whether mine tailings from the Sierrita mine, containing significant amounts of clay, might be a suitable feed material for the production of structural products. “Brixx” is the commercial term used to describe the resultant structural product formed in the test work. This paper is a preliminary evaluation of a technology that is being considered by Freeport-McMoRan. This report is not an endorsement by Freeport-McMoRan of the process or products, nor is it a commitment to use this technology."

Jan 1, 2008

By Dyson N. F

Mixed cobalt-nickel sulphides precipitated from ammoniacal process liquors derived from nickel sulphide concentrates, mattes, and reduced nickeliferous laterites have been characterized.The mixed sulphides are prone to oxidation on standing and are rapidly leached under relatively mild conditions. The kinetics of the leaching reactions are controlled principally by temperature and oxygen partial pressure. Although the samples have different CO:Ni ratios and have undergone varying degrees of oxidation, there is little difference in their leaching behaviour. The results suggest that a single plant would be able to process mixed sulphides of varying composition. Any copper and zinc present in the mixed sulphides as impurities also go into solution and must be removed prior to recovery of the cobalt and nickel in metallic form.

Jan 1, 1981

By Vestre J, Kure K, Bergqvist I

Existing practical laboratory tests for comparative strength determination of commercial explosives consist of the lead block test, the ballistic mortar test, the bubble test etc. These tests are carried out in material with quite different properties compared to rock. The theoretical performance potentials of commercial explosives are traditionally described by weight-strength (WS). Some explosive producers use the Langefors formula for weight-strength calculation, where also the gas volume is considered. Neither the theoretical nor the practical methods for determination of explosive performance such as the above, give good enough prediction of fragmentation and heave in rock blasting. For these reasons a project was started for the purpose of finding a small scale test method which predicts how different explosive parameters affect fragmentation and heave. Small scale tests were carried out by using 50 cm cubical blocks, mainly of concrete, but a few also of rock. All blocks were blasted in a steel cylinder with a diameter of 1.2 meters. The velocity of detonation was monitored, and the velocity of fragments was derived from their time of arrival at the steel wall, which was registered by accelerometers. After blasting all fragments were screened. The charge diameter was 22 mm and the amount of explosive 78 grammes, resulting in a specific charge of 0.62 kg/m3. Explosive properties such as energy, gas, VOD and density were systematically changed.The results presented in this paper show how fragmentation and heave systematically change when the explosive properties like energy, gas, VOD and density are systematically changed. The results from the small scale tests are compared to full scale tests carried out in tunnel blasting, and during summer 1990 also in bench blasting.

Jan 1, 1990

By McKinnon R. L

Laboratory and field work on the use of wetting agents for suppression of colliery dust is described. Although the results were inconclusive they were not discouraging and further investigation is required. The use of certain wetting agents may constitute a healthhazard.INTRODUCTIONCoal dust presents explosion and health hazards to the coal mining industry. The problem of dust suppression is particularly acute where water alone is unsatisfactory for this purpose. The addition of a surface active agent (wetting agent) to the water should enable the dust particles to be more easily wetted and thus more easily prevented from entering and spreading through the mine atmosphere.Investigations into this effect carried out at The University of Sydney mainly under research grants from The Joint Coal Board (Dawson and Hargraves, 1955; Charlton and Curnow, 1957) are summarized, and information on the possible harmful effects of certain wetting agents is given.Twelve local manufacturers and five importers supplied 52 wetting agents in liquid, solid, powder, and paste form.The active material content varied from approximately 10 per cent to 100 per cent and the cost per pound from 8d. to 14/3.LABORATORY TESTINGPossible test methodsThree methods of laboratory testing were considered.1. The standard method for comparing wetting agents is the Draves test, used in the textile industry on cotton...

Jan 1, 1961

By L. R. Verney

About 75% of the market economy countries's supply of cobalt is produced in Central Africa by Zafre and Zambia. Zafre alone accounts for more than 55% and has the resources and capacity to increase output significantly at any time so its dominant position is unlikely to be challenged in the foreseeable future. Other producers from domestic resources are Canada, Australia and South Africa; and Cuba, probably the most important producer outside of the Market Economy countries. Belgium, Norway, France, Japan and Finland produce cobalt from imported materials. While there are "cobalt ores", inMorocco, USA, Canada and the USSR, the mineralisation is complex and cobalt extraction is costly. In ZaPre and Zambia cobalt is a by-product of copper; in Canada, Australia, France, and Cuba it is a by-product of nickel; and in South Africa it is a by-product from the production of Platinum Group Metals. Thus the levels of cobalt production are inevitably related to the production of other primary metals. While some cobalt is produced by predominantly pyrometallurgical methods most of the world's cobalt is produced hydrometallurgically. The existence of large hydro-electric power plants and the mineralogy of the copper and cobalt concentrates encouraged research and development in Zafre of the recovery of copper and cobalt by electrowinning from sulfate solutions; much pioneering work was carried out, which lead to construction of the two largest copperlcobalt hydrometallurgical plants in the world, at Shituru and Luilu. Similar systems were adopted in Zambia. In Canada high pressure hydrometallurgical processes based on the sulfate system were developed and adopted in Australia, the Philippines, Finland and South Africa. Meanwhile developments in chloride hydrometallurgical extraction of nickel and cobalt lead to its use in the extraction of cobalt in Norway, France and Japan.

Jan 1, 1988

By J. L. Cupp, R. C. Ford, B. R. Romig

The Climax Molybdenum Mine, located near Leadville, Colorado, is the site of a lengthy mining history spanning more than 80 years. In the 1960’s, extraction of molybdenum from oxide ore located adjacent to the massive molybdenite sulfide deposit resulted in the construction of an earthen core dam to impound fine-grained oxide tailing in the Eagle River Valley. Through recognized value of water storage and reclamation opportunities, a tailing removal project was initiated in 1993 to convert the impoundment facilities to a post-mining beneficial land use of developed water resources. An evaluation of the effect residual materials and lake dynamics would have on in-stream water quality was performed. Eagle Park Reservoir stands as a model for future reclamation efforts that involve water delivery to highly sensitive receiving waters. This paper provides a case study on project development, the evolution of water quality assessment, and the regulatory framework that contributed to this project’s success.

Jan 1, 1999

By X Zhang, B McFadzean, C T. O’Connor, S Pikinini

The Platreef in South Africa contains one of the world’s largest reserves of platinum group elements. One of the major platinum group minerals (PGM) components in this ore is sperrylite (PtAs₂), which has been found to be slow floating compared to the other PGMs. In a study aimed at determining the reasons for the poor floatability of sperrylite and to improve its recovery, tests were carried out to determine the interactions of the mineral with a range of standard and novel collectors. Microflotation tests were carried out to determine the hydrophobicity of the minerals before and after adsorption of collectors. In addition, experiments were carried out to determine the enthalpy and extent of collector adsorption on the minerals and to investigate electrochemical interactions between sperrylite and selected standard collectors. The results indicated that poor collector adsorption was the major cause for the poor floatability of sperrylite. Sperrylite had both poor natural (14.5 per cent) floatability and collector-induced flotation recoveries, the highest recovery of 26 per cent being observed using PNBX collector at pH 9. Moreover, the rest potential tests showed that the interaction of sperrylite with standard collectors such as xanthates was poor. The decrease in potential after the addition of the standard collectors ranged from 7.9 mV to 24.9 mV under alkaline conditions. Furthermore, sperrylite rest potentials remained unchanged with a change in pH from basic to acidic, indicating its resistance to surface alteration. Surface alteration of the minerals is key for the chemisorption of collectors to take place on the mineral surface. This was further emphasised by flotation recoveries at low pH, where only certain collectors responded positively to a decrease in pH and these were shown to have undergone a structural change. This work has highlighted the difficulties associated with sperrylite flotation and provides some direction for future research.

Aug 24, 2022

Measurement of densities, susceptibilities, permanent magnetization, and calculation of demagnetization factors has allowed computer modelling of gravity and magnetic data over the Middleback Range iron formations of South Australia. As well as providing structural information, the study emphasizes the effects of weathering on the interpretation of magnetic data.

Jan 1, 1975

By D Reid, J Vinod, M Rahman, A Fourie, T Vo, J Ayala, A Russell

This paper reports on an industry and Australian Research Council funded research project, TAILLIQ, that is a joint initiative between four Australian Universities. The paper discusses the accuracy with which the critical void ratio can be determined for a given tailings; it does this by presenting the results from a ‘round robin’ study in which 18 geotechnical laboratories around the world participated, testing the same tailings (sampled from a gold mine in Western Australia). The results were variable, although a reasonable number were very similar, as described in the paper. The paper provides additional test data for sandy silt gold tailings recovered from a sponsor’s site in Australia, including preliminary calibration chamber test data, results from direct simple shear tests and characterisation tests to determine unsaturated geotechnical properties.

Jul 1, 2021

By E. J. Gleim

The Bureau of Mines customarily publishes lists of equipment meeting its safety standards to keep the mining industry informed as to the development and availability of mining equipment that can be used safely. The present list supplements Bulletin 543, Permissible Mine Equipment Approved to January 1, 1953, as well as Information Circular 7722, Permissible Mine Equipment Approved During the Calendar Years 1953-54. Because standards have been revised and new ones added by the Bureau, this list contains classes of equipment not previously covered.

Jan 1, 1958

By A. W. Deurbrouck

The separations achieved by eight conventional cyclone washers have been evaluated to determine their performance when processing intermediate size coal of 28 mesh bottom size. The dense-medium cyclones provided efficient, sharp separations in treating feeds of up to 44 percent of near-gravity material at separating specific gravities ranging from 1.42 to 1,55 (one separation of a secondary feed was made at 1.63). Complete washability analyses are shown by sizes of the composite feed to these cyclones. The magnetite losses per ton of coal processed ranged from 0.6 to 2.0 pounds; however, of the eight plants reporting losses, seven indicated magnetite losses were 1.1 pounds or less per ton of coal processed.

Jan 1, 1972