Search Documents

By L Nienaber

Mines, after becoming operational, often retain the same support and reinforcement designs developed in the feasibility study. These designs are conceived from limited drilling data and regional experience, thus having an empirical flavour. Empirical designs are perceived to be conservative, catering for a variety of failure mechanisms, which are not always present in mine development drives.This begs the question: If you were to invest in the necessary resources to obtain sufficient data and complete the required analyses for the different development drives in the mine, to engineer a support and reinforcement scheme with the capacity to match the demand of the rock mass, what is the difference in cost when comparing an empirical design to an engineered design?To answer this question, mine tunnels with different geometries and orientations, where detailed structural data was available, were selected for a comparative design exercise. Material cost, development cost, cycle time and professional fees for engineered and empirical designs were estimated. The outcome is summarised in the following paper that discusses the process followed and the results of the design comparison.

Mar 8, 2011

By G. Luttrell, S. Keles, M. Eraydin, R. Yoon

The dewatering of fine particles is energy intensive and often requires costly capital expenditures. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids that enhance the performance of existing filtration equipment and an innovative hyperbaric centrifuge that utilizes both air pressure and centrifugal force for dewatering. The moistures obtained using these processes are 30-50% lower than those obtained using conventional methods. Another dewatering technology, known as the hydrophobic displacement process, can reduce product moistures to a level previously attainable only through the use of thermal dryers. This article presents test results obtained with these various advanced dewatering technologies along with estimates of the power consumption for each process.

Jan 1, 2007

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By Renato G. Bautista

"The chemistry of the separation of metals from each other and from the other undesirable components involve multiple simultaneous chemical reactions. In the case of leaching, the heterogeneous chemical reactions between the solid and the liquid phase may be limited to a few reactions. In the homogeneous liquid phase, the number of simultaneous chemical reactions could be double or triple that of the number of heterogeneous reactions. The rate of dissolution becomes very dependent on the changing concentrations of the significant chemical species taking part in the multiple reactions in both the heterogenous and homogeneous phase. The rate expression developed for the process must take into account the mechanism of chemical reactions in order to best represent the actual process. This paper also examine the role of mass transfer with chemical reaction in the develpoment of the rate equations for dissolution, liquid-liquid extraction, membrane separation, precipitation, and electrodeposition.IntroductionThe understanding and the elucidation of the mechanism of the rate phenomena for a specific chemical reaction system is of prime importance in the development of a successful chemical process. The development of successful emerging technologies for metals separation will depend on the accurate interpretation of the intrinsic chemical reaction kinetics and the rate of mass transfer of the desired metal species during its separation from the undesirable chemical species. This is the case whether the process application is for separation, concentration, and /or purification.The chemical processes that will be examined in this presentation will include leaching, solvent extraction, membrane separation, precipitation, and electrodeposition."

Jan 1, 1996

By Anthony J. Konya

"This paper was written during part of the author’s student co-op with Cargill Salt at its Avery Islandunderground salt mine in Louisiana. Blasting salt is a unique type of blasting that is different than blasting other rock types. The plastic nature of salt, along with its large swell factor make salt a challenge to blast. The Cargill salt mines use and have tested a variety of different methods for breaking salt in an efficient manner, however these blasting methods are rarely used in other operations nor talked about today."

Jan 1, 2016

By Dakota D. Faulkner

Cable bolts have been very effective in mine ground control. Non-tensioned and tensioned cable bolts are now used for both primary and supplemental bolting (Suder, 2001; Mirabile, 2010). In the United States, cable bolts are typically installed in either 1 or 1-3/8 in. (25 or 35 mm) diameter drill holes and, if point anchored only, are utilized with 4 - 5 equivalent feet (1.2 - 1.5 m) of resin. Cable bolts can be tensioned by various methods such as using an expansion shell mounted on the cable or post-tensioned with a hydraulic cable tensioning unit. In recent years there has been a desire to completely encapsulate the cable bolt for corrosion protection. Fully encapsulating a cable bolt with traditional resins can be very difficult. Keystone Mining Services, LLC (KMS) and Jennmar Corporation have developed a new cable bolt that can be fully encapsulated during installation or post-installation with polyurethane (PUR). The Fully-Grouted Cable Bolt (FGCB)* is equipped with a special head that allows the injection of PUR up through the cable bolt head and cable strands, completely encapsulating the cable and filling the drill hole. Although the FGCB was initially developed to fully encapsulate the cable for corrosion protection, it was also found that by modifying the cable bolt head and injection pressure, PUR could be injected into cracks and fissures of the strata to stabilize the roof. This paper details the development of this system and three underground applications under different ground conditions.

Jan 1, 2012

By B. W. Raymond, D. W. Zandee

"IntroductionCoal deposits are found in many regions in Canada and vary widely in their age, quality and rank. All classifications of coal except anthracite are found in significant quantities in this country.Deposits in the Maritimes are mainly bituminous; Lignite is found in Saskatchewan and Ontario and sub-bituminous coal in the plains region of Alberta. The Rocky Mountain coalfields of Alberta and British Columbia contain low and high-volatile bituminous coal and, in a few places, semi-anthracite. The British Columbia interior contains deposits of semi-anthracite, bituminous, sub-bituminous coals and lignite. The Yukon and Northwest Territories also contain substantial deposits of bituminous coal and lignite.Currently Nova Scotia produces both thermal and metallurgical coal, Saskatchewan produces lignite and Alberta produces both sub-bituminous and bituminous coal for thermal purposes. Large deposits of metallurgical coal are now being exploited in the Rockies arefl of British Columbia and Alberta by open pit methods. The raw coal is treated in large capacity preparation plants to remove refuse and upgrade the product to a consistent metallurgical quality with respect to ash, moisture, volatile matter and coking properties.The treatment of coal involves crushing, screening and cleaning by dense medium, jigs, water-only cyclones, tables and froth flotation to produce a diverse range of coal products differing in quality and size for various end uses.The chapter on Crushing and Screening Circuits was concerned mainly with crushing of metalliferous ores to produce a concentrate of one or more valuable minerals which normally constitute a small portion of the original mass of the material treated.Coal differs physically from ores in many ways such as lower specific gravity, relatively large volumes but low tonnage of product, and its habit of absorbing moisture requires extensive dewatering processes more complicated than settlement and filtration. Most significant, for this paper at least, is the fact that crushing coal is not as energy intensive and much smaller equipment is applicable.Crushing and screening of ores is intended to reduce the size of all constituents as quickly and efficiently as possible to allow liberation of the mineral particles. The crushing of coal is different in that the coal is not the minor constituent and the production of fines, in the initial stages at least, is highly undesirable. The basic objectives of crushing coal are the reduction of run-of-mine material to sizes suitable for cleaning or further reduction of coal to market sizes."

Jan 1, 1989

By B. F. Dickerson

STRATEGIC METALS! Recently, this money accented cry has been heard in such diverse locales as Mining company boardrooms, Banker's offices, Stockbroker's quarters, Swindler's dens and Congressional committee rooms. (In some cases, these locales are one and the same). Is the strategic metals rush for real? Should it be? Our paper attempts to give a very generalized view of the subject for a few metals, points to a few potential, but generally overlooked sources of these metals, and offers conclusions based on our studies.

Jan 1, 1981

By H Bao, M Nehring, M Kizil, P Knights

The mining sector, a notably energy-intensive industry worldwide, is a major consumer of fossil fuels, leading to significant carbon emissions globally. The move towards electrification, coupled with advancements in battery technology, has redirected focus from traditional diesel-powered solutions to battery-powered alternatives. This paper introduces a novel mining haulage system, termed the Battery Trolley system, and examines its theoretical foundations, configurations, and operational processes. It offers a comprehensive analysis of the system’s characteristics and limitations. Through a hypothetical road simulation, the study analyses various battery mining trucks, calculating energy consumption based on force parameters and tailoring battery sizes to contemporary materials and technology. When assessing various battery truck alternatives—considering aspects such as battery size, effective payload, duty cycle, energy efficiency, productivity, and single-shift production—a range of performance outcomes and characters become apparent within the mining context. The findings indicate that Battery Trolley configurations, requiring smaller battery capacities, entail lesser compromises on effective payload. Consequently, these configurations achieve a higher duty cycle, reduced energy consumption per tonne, heightened productivity, and enhanced singleshift production capabilities compared to Battery-only alternatives. The comparative analysis of Battery Trolley with stationary charging (BT-S) and Battery Trolley – dynamic charging (BT-D) underlines that battery Trolley systems are capable of overcoming the challenges associated with battery size, thus successfully fulfilling the production demands of large truck applications in mining. This positions Battery Trolley systems as a more advantageous option for the decarbonisation of mining fleets, underscoring their potential in contributing to the sector’s sustainable evolution.

Sep 1, 2024

By Wilford S. Wright, Harold E. Heide, Robert S. Sanford

"INTRODUCTION The United States production of tin has always been negligible, and domestic requirements have been met almost entirely by imports. The advent of war in Europe in 1939 brought a threat to our foreign source of supply, and steps were taken by Congress to forestall shortages of tin and other metals. By authority of the Strategic Minerals Act, passed by Congress in 1939, the Bureau of Mines and Geological Survey conducted investigations of domestic tin deposits.An examination of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.H. B. Heide conducted a preliminary examination of lode and placer-tin deposits at Cape Mountain in 1942, which was followed in 1943 and 1944 by a program of exploration by churn drilling in the placer area and trenching and sampling the lode deposits.Placer tin, found at the head of Goodwin Gulch, Cape Creek, First Chance Creek, and Boulder Creek, indicates that the mineral was derived from the vicinity of lode cassiterite occurrences on Cape Mountain. Placer tin led to the discovery of at least one, cassiterite vein by the Geological Survey and the Bureau of Mines."

Dec 1, 1946

By V. I. Ryaboy, S. A. Kondratyev

"The paper describes influence of desorbed species (DS) of a number of xanthates and higher dialkyldithiophosphates on the collective ability of these reagents. Adsorbed on mineral DS of the reagents in the form of products of non-stoichiometric interaction between xanthates and heavy metal salts can pass to the gas–liquid interface and remove liquid from the layer between mineral particle and water surface. A high-speed video recording displays the process of spreading of DS of xanthates and dialkyldithiophosphates over water at the moment of local rupture of the water layer. Expansion of “dry” spot on the mineral surface after DS of xanthate capture and displace liquid from the layer has been proved with video images. The comparative analysis of collecting ability and dynamic surface activity of dialkyldithiophosphates shows that these characteristics are in good correlation. The forces exerted by spreading film of the reagent’s DS on liquid in the water layer are evaluated, and the water flow rate from the layer is determined. The line of the reduction in thickness of the water layer behind the front of spreading film of DS of dialkyldithiophosphates and xanthates coincides with the line of the increase in their dynamic surface activity. Their force on the liquid volume in the water layer characterizes collecting ability of the DS film of xanthates and dialkyldithiophosphates. It has been supposed that the collecting ability of DS of a reagent is a part of its overall flotation activity, conditioned by surface tension of solution and, thus, defined by the structure of hydrocarbon fragment of the reagent.INTRODUCTIONIt is believed that collecting ability and selectivity of collecting reagents is mainly governed by adsorption of a reagent at the solid–liquid interface. A few studies have shown that activity of collecting reagents at the gas–liquid interface may have deep influence on their collecting capacity and selectivity. Experimental researches have revealed correlation between surface pressure in a carboxylic acid film on liquid’s free surface and floatability of useful components (Kulkarni & Somasundaran, 1975; 1980; Quast, 2006). According to Quast (2006), it is not always that surface pressure of a reagent film influences collecting ability of carboxylic acid. For instance, pH range of adsorption of tetradecanoic acid on hematite does not coincide with pH range of high surface pressure. So, surface properties of this acid contribute little to flotation efficiency.The correlation between reagent film surface pressure and mineral floatability has been reveled for quartz and cationic reagents, too (Bleier, Goddard, & Kulkarni, 1977). Finch & Smith (1973) showed that combination of adsorption of ion–molecular amine complexes on mineral surface and high surface tension of “fresh bubbles” was favorable for flotation performance. The use of bubbles with reduced surface tension resulted in a decrease in quartz floatability."

Jan 1, 2016

By AIME AIME

NEW YORKERS look forward to the third week of February as the time of the year when they can count on seeing their friends-from far and near gathered in the city for the four-day annual session of the Institute.., Indeed, the metropolitan district is so large that in engineer who lives in New, Jersey and has his office on the lower end of Manhattan island may easily pass a whole year without seeing an acquaintance who lives in Westchester and has an office near Forty-second Street. If the Institute served no other function than to provide a place where friendship may be renewed, ideas exchanged, and new acquaintances made it would still be worth while. But when about 30 technical sessions at which about 160 papers are read and discussed are compressed into four days the annual meeting is also entitled to high rank as an intensive course of post-graduate instruction in the newest development in mining and metallurgical technology. Last, but not least, it is the occasion of a good time for one and all, even if they do get more than a little behind on sleep before the end of the fourth day. Nine o'clock is the time set on Monday morning for the beginning of registration, but a half-hour before that a number have always 'put in an appearance, and this is fortunate, because by 10 o'clock four sessions had begun, those on mining methods, geophysics, a round table on the valuation of coal, and the session of the Local Section delegates. Three committees of the A. S. T. M. were also in simultaneous session, so the meeting may be fairly said to have started "in high."

Jan 1, 1931

By Christoph Mueller

Broad band mine communication traditionally is characterized mainly by individual solutions, which have in common their long development phases and their high cost for development, operation and service. The use of Ethernet and the TCP/IP family of standardized protocols provide an uniquely price efficient combination of high bandwidth open networking, universal use and accessibility of price efficient development tools, especially because it forms the technical infrastructure for the worldwide Internet. TCP/IP and Ethernet assures reliable networking however it is not able to guarantee the latency timing of forwarding network information. Therefore, the network design requires strict load limitation and application level traffic control especially if moving equipment has to be manually remotely controlled via the network. The paper discusses the technologies the application of Ethernet and WLAN in underground mining environments.

May 1, 2006

By R. W. Lawrence, O. Lopez

Many gold deposits in the world have not been developed clue to the presence of copper and other base metals which can cause metallurgical and environmental challenges clue to the formation of base metal cyanide complexes. SART technology (sulphidization-acidification-recycle-thickening) can resolve these issues by recovering copper as a high grade sulphide concentrate, recycling the associated cyanide back to the gold leach, and eliminating the downstream environmental liabilities. Project economics can be improved substantially, leading to a positive re-evaluation of new and existing gold-copper projects. Some aspects of the design and operation of two recently commissioned SART plants will be discussed.

Jan 1, 2011

By Wylie A. W, Mathew P. J, Eisler P. L

Field studies of the radiations backscattered by iron ores from a 60Co source of primary gamma radiation located in a borehole logging probe have confirmed thatthe P" factor, a ratio of high energy gamma ray intensities to low energy intensities in selected energy windows of the backscattered gamma-ray spectrum, is a valuable measure of grade for sedimentary iron ores of the Pilbararegion of Western Australia.Laboratory studies of model boreholes have shown that variations in borehole diameter and variations in bulk density of the formations have a significant influence on the measurement of P" ratios. If these influences 'are taken into account the mean ore grade in a new blast hole, for instance, can be predicted with a probe of suitable configuration to within 0·8 per cent Fe at the 95 per cent confidence level, while the grade of a single 120-cm split can be determined to within 2·6 per cent Fe. These results were obtained by pooling data from five blast holes covering the range of iron concentrations 20-68 per cent Fe and apply to the mean hole grades 54-68 per cent Fe.Results for two development holes were generally comparable to those obtained from individual blast holes95 per cent confidence limits of ±0·9 per cent Fe for mean ore grade and ± 4·1 per cent Fe for single splits. A greater number of data points is needed before these confidence limits can be further improved.The technique utilized to obtain these results was derived from a "multiband" approach to collection of backscattered spectral intensity data, an approach which permitted selection at the data processing stage of the most statistically significant P" ratios for the type of mineralization encountered in the field. The multiband technique also permitted selection of the most significant of another set of windows in the backscattered gammarayspectrum to measure a newly developed "S-factor", a ratio sensitive to borehole diameter. Another window provided information on bulk density. All these measurements were made with a single pass of the same loggingprobe.

Jan 1, 1977

By E. R. Mueller

The natural lives of machines and components vary tremendously! Maintenance managers struggle constantly to maximize their equipment lives while minimizing their maintenance costs, but they normally lack the tools and techniques they need to do this properly. This paper proposes a methodology based on probabilities of failure and expected values for repairs that recognizes the variation among individual machines and components as well as the high costs associated with catastrophic failures. It enables a user to determine the optimum change-out intervals for many types of equipment. The approach proposed here is sophisticated enough to be reliable but simple enough to be applied by the maintenance staff on the shop floor. It will complement existing preventive and predictive maintenance programs.

Jan 1, 1995

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: (1 ) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold s so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfide and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By C. E. Reistle

The tests reported in this paper were made in the East Texas field in the summer and fall of 1932 as a part of the Bureau of Mines study of the operation of flowing wells and reservoir performance; and to determine, if possible, the minimum reservoir pressure necessary to produce the wells in this field by natural flow through different sizes of flow strings. The minimum reservoir pressure that would be required to maintain natural flow through 2 1/2-inch tubing was determined experimentally for the existing energy conditions in the East Texas field. With the present available data, however, it 'is impossible to predict accurately or to determine by calculation the necessary energy requirements for maintaining the vertical flow of oil and gas mixtures under all conditions. Although some valuable data were obtained which seem to have application to the solution of problems involving vertical flow, this important research of the petroleum industry is so involved that more study of the complicating factors influencing the flow of oil-gas mixtures through vertical pipes is required. Versluys4 has presented a mathematical analysis of the vertical flow of oil and gas mixtures which covers the fundamental theories of the problem-although, as he points cut, there are factors, particularly friction, slippage, and solubility of the gas in the oil that must be mown or determined experimentally before the equations he has developed can be applied to actual

Jan 1, 1933

The Bayswater seam of the Singleton Coal Measures is discussed in relation to its field occurrence and related li~hotype profiles. The seam is correlated throughout widely separated areas of the Hunter Valley with the Farrells Creek seam at Howick, Broke seam at Broke, and Saddlers Creek seam at Mt. Arthur. The unusual features of composition of the seam in relation to adjacent seams is dealt with in terms of the seam environment, particular attention being given to the sandstone at the base of .the seam. Petrographic and other data are used to support the arguments submitted.

Jan 1, 1973

By H Bruyn, K Ehrig, V Liebezeit, A Robertson, M Smith, D Grant

"The Olympic Dam geometallurgy program has generated a large quantity of data that has been used to create a geometallurgically enabled block model. An ongoing challenge is to convert data into usable information and embed geometallurgical practices into resource model development and mine planning to assist with the identification of opportunities to maximise value.This paper will discuss the methods used to disseminate geometallurgical information throughout the planning life cycle including data extraction methods from the geometallurgy acQuire database, and the inclusion of a geometallurgy module in the Olympic Dam Stope Reserves database. The use of geometallurgical information in short-, medium- and long-term mine design and scheduling, including its use in grade descriptor development and stope value assessment tools will also be presented. The detail of development of specific geometallurgical models is outside the scope of this paper.At Olympic Dam, the incorporation of geometallurgical capability within the long-term planning team, traditionally the domain of mining engineers, has proved essential in broadening the base of geometallurgical knowledge as well as focusing geometallurgy resources on value-adding areas while providing a holistic risk based long-term plan.CITATION:Liebezeit, V, Ehrig, K, Robertson, A, Grant, D, Smith, M and Bruyn, H, 2016. Embedding Geometallurgy into Mine Planning Practices – Practical Examples at Olympic Dam, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 135–144 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016