Search Documents

By Ken Andromalos

Continued population growth combined with limited water resources in the Denver area has resulted in the conversion of a number of mined out gravel pits in the area into municipal water storage facilities. The use of slurry walls provides a cost effective means of isolating groundwater to convert these pits into efficient water storage facilities. Design considerations include: stability, underlying bedrock conditions, backfill mix design and earthwork requirements. Installation issues during construction include: trench stability considerations when excavating through relatively clean sand and gravel deposits in potentially high groundwater conditions; keying into three to ten feet of fractured claystone, siltstone or sandstone that makes up part of the Denver formation, and quality assurance procedures to assure a proper groundwater barrier is constructed. The paper concludes with two brief case histories to illustrate how these considerations are applied

Jan 1, 2007

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By Chris Harnan

This paper describes the geology of three European cities and outlines how the geology has lead to the development of specific foundation construction techniques. Comparative tables of techniques commonly employed are given in Section 5. It can be seen that despite the presence of the 'single market', techniques still have wide diversity despite some similarities in geotechnical conditions.

Jan 1, 2000

By F. Djahanguiri

The U.S. Bureau of Mines is conducting research on underground stope leaching of metalliferous ores to minimize the environmental impact of ore processing on the surface and to maximize minable reserves. An aspect of this research is to minimize pregnant solution losses and/or groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope leaching economics. A reinforced concrete bulkhead was designed, constructed, and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead design methodology and construction procedure.

Jan 1, 1995

By Steven L. Anderson

A cut-off wall has been designed and is currently under construction along the Back Dam of the existing tailings impoundment at Red Dog Mine, Alaska. The cut-off wall, which will be in the order of 5,000 ft long and up to 150 ft deep, when complete, is being excavated using a 40 metric ton Bauer trench cutter head mounted on a Liebherr crawler crane, in combination with a closed loop slurry pumping and de-sanding system. The tailings impoundment is situated in an area of warm permafrost and high potential seismic activity. Design incorporated an assessment of rock jointing to define the final depth of the wall along the alignment requiring the use of plastic concrete backfill to address the concerns associated with potential cracking of the wall due to settlement and during seismic activity. The results of the geotechnical investigation program, particularly with respect to variation in rock hardness along the wall alignment are discussed, as are the design criteria for the plastic concrete backfill, the challenges faced during construction, including scheduling of the work with the on-going dam raise activities of the mine, and the lessons learned with respect to potential productivities and selection of cutter wheels and teeth. Also described are the requirements for and advantages of utilizing a slurry boosting system to meet pumping requirements, re-design of the plastic concrete mix to consider workability and optimization of cutter teeth configurations to reduce wear through highly varied rock hardness.

Jan 1, 2010

By Edwin Itzig-Heine, Daniel Traylor, Bernard Tarralle, Michael McKenna

This paper discusses the challenges associated with the design and construction of a dual-cell, “figure eight” shaped shaft in saturated, soft ground for the Northeast Interceptor Sewer project in Los Angeles. The shaft will be excavated to a depth of41 m and used to launch two EPB TBMs. The specifications required concrete diaphragm walls, embedded below the shaft invert, and a grout curtain beneath the wall. To control water pressure and basal stability without a grout curtain, wall panels were embedded deeper than required into a stiff, cohesive deposit. Details of wall panel excavation using a Hydrofraise are presented.

Jan 1, 2003

By Robin B. Dill, Mark Pelletier, Daniel J. Dobbels, Subodh Bhaumik, Daniel J. VanRoosendaal

Although primarily cut-and-cover excavations are required for replacement of the existing elevated I-93 interstate highway through the heart of Boston for the Central Artery/Tunnel (CA/T) project, some mined tunnel construction was also undertaken. The mined tunneling conducted was the 22-m-wide northbound roadway structure which passed below a 20-m-deep operating underground subway station that was built in 1913. The innovative underpinning scheme used to support the subway station during construction resulted in the successful mining beneath the subway station with negligible vertical settlement. Two grouting galleries were carefully mined below the subway structure, and pre-grouting of the granulary, pervious glacial soils and weathered bedrock was carried out from these galleries. The reinforced concrete walls of the underpinning structure were constructed within three stacked drifts that were sequentially mined below each grouting gallery. After 11 cross adits were mined between the grouting galleries, cast-in-place post-tensioned girders that spanned between the stacked-drift walls were constructed to support the subway station. The stacked-drift walls also provided lateral support for the 22-m wide by 29-m long by13-m high opening beneath the girders.

Jan 1, 2001

Impala Platinum?s No.16 Shaft mine is currently under construction and is expected to reach full production of 256 500 tons per month by 2014. Mining will start at 1 260 m below surface with a maximum mining depth of 1 535 m where virgin rock temperatures of 56.6°C will be experienced. As a result of depth, high virgin rock temperature and narrow reef mining, an expected total of 31.5 MW[R] of air cooling capacity will be required to achieve acceptable underground conditions. This will be achieved by cooling mine intake air in a single dedicated air cooling installation located on surface. The compact installation includes air cooling spray chamber, refrigeration machines, condenser cooling towers, evaporator and condenser water reticulation as well as all electrical and control systems. Construction and commissioning of the first phase of this air cooling installation has recently been completed on a turn-key contract basis.

Jan 1, 2009

By Allan Sylvester

Construction of the Shot Tower Metro Station in Baltimore, Maryland was performed in two phases. In the first phase, a contractor was retained to excavate the station in order to construct twin tunnels from the Shot Tower Station to the John Hopkins Station. The retention system for this 70' deep excavation consisted of a Soldier Pile in Tremie Concrete (SPTC) wall supported by cross-lot bracing. In phase two, The Clark Construction Group, Inc. was retained to construct the station interior structure, two entrances, two station ancillary shaft structures and the track work for the station and tunnel. The excavation for the construction of the two entrances adjacent to the 70' deep station SPTC wall had to proceed prior to completion of the station structure due to the tight construction schedule. A system of overlapping secant piles was specified as a vertical support of excavation element for the West Entrance. The secant piles would have provided a watertight, rigid support to resist the load from the SPTC wall constructed in phase one. A watertight system was required in order to minimize the settlement of adjacent buildings supported on wood piles. Clark Construction was concerned with the constructability, cost and performance of the specified secant piles and looked for other innovative methods of providing a watertight and rigid system. Substitution of a reinforced slurry wall in lieu of the secant piles was cost prohibitive due to the additional cost of concrete placed under tremie. Clark, being familiar with cement-bentonite cut-off walls and slurry wall construction procedures, proposed the construction of a PSHG wall, in lieu of the secant piles. The PSHG wall construction consisted of trenching 30" wide by 20' long by 60' deep panels under a self-hardening slurry. Once the excavation for a panel was completed, a 60' deep prefabricated soldier beam and lagging panel was placed in the slurry. The slurry design mix then self-hardened within the cure time, allowing excavation for the structure to proceed This paper will discuss the design, details and construction methods used on the PSHG wall and will compare the advantages of the PSHG system to conventional support systems.

Jan 1, 1997

By N. S. Yet

This paper shall present the design and construction of bored pile and diaphragm wall for the proposed MHA complex in Singapore. The work was carried out by L&M Foundation Specialist Pte Ltd and PWD Consultants Pte Ltd was the consultant for this project. A brief description of the project is first presented to illustrate the scope and scale of the work involved, which includes the construction of bored piles and diaphragm walls and installation of steel stanchions in the bored piles. This is followed by a description of the methodology used to analyse and design the wall and bored piles. As both towers in this project are supported on bored piled foundation and are constructed by top down construction method, the analysis of the wall has taken into consideration the sequence of work phase by phase and this was carried out by means of a commercial finite element program called CRISP. Modelling of the problem will be briefly described and the findings from the numerical analysis will be presented. This is followed by a description of the structural and geotechnical design aspects of bored piles. The paper shall then describe the difficulties encountered for this project and solution used to solve the problem. The subsoil condition will be described with special mention on the encounter of very strong granitic rock at depth above the maximum excavation level of the basement at certain locations, hence necessitating the drilling of rock for a considerable depth for both bored piles and diaphragm wall. At this juncture, the construction method used to drill through the rock will be briefly described. For construction of bored piles, penetration of rock was carried out by chiselling or drilling using reverse circulation rigs. For construction of diaphragm wall, it requires the employment of Bauer hard rock cutter which uses cutting wheels fitted with roller bits and are capable of excavating into granitic rock of compressive strengths more than 100 MPa.

Jan 1, 2000

By Charbel Khoury, Kwabena Ofori-Awuah, Kofi B. Acheampong

"Following heavy rains in spring of 2014, Prince George’s County officials issued a mandatory evacuation for homes in the Piscataway Hills subdivision of Fort Washington, Maryland where a landslide along a 1700-foot hillside destabilized homes, collapsed the single access road, and resulted in water and sewer mains break. Forensic investigations, including geologic assessments, test borings and in-situ Cone Penetrometer and Dilatometer soundings, were performed to evaluate subsurface conditions and provide stabilization options for the roadway and slopes. Post-failure ground movements were monitored using inclinometers. Critical failure planes were identified within the underlying 30-foot thick Marlboro Clay formation, a known geologic hazard with historic occurrences of landslides and slope failures.This paper discusses the remedial design for stabilizing the landslide and 60-foot hillside slope failure, and protecting the roadway. Amongst several feasible options, driven piles were selected in consultation with the County and retained contractor based on cost, environmental impacts and site constraints. Constraints included private ownership of hillside slope, upslope buildings safety; deep-seated failure, relocation of underground water and sewer mains, and accelerated construction schedule.Pile design included global slope stability analyses and lateral pile analyses using several loading configurations to optimize pile geometry and spacing, and determine a value-engineered design satisfying both serviceability and strength limit states to achieve long-term stability with factor of safety of 1.3. Soils within the active landslide plane were assumed to provide no resistance, while soils below the failure plane provided lateral resistance. This stabilization scheme, which extended along the 1700-foot roadway section and toe of hillside slope area, consisted of 410 steel HP16x141 piles in two to three rows driven to depths between 60 and 70 feet below the Marlboro Clay stratum at 5 to 7-foot spacing."

Jan 1, 2017

By Allan Sylvester, Paul E. Gabryszak, Diane R. Hirsch, David P. Field

With construction of the first phase of the Automated People Mover (APM) Tunnels nearing completion, this paper will address how knowledge from recent Tunnel Boring Machine (TBM) and New Austrian Tunneling Method (NATM) tunnel construction at the airport was used to refine the methodology for the next phase of tunnels currently in design. The benefits include an enhanced understanding of the ground conditions; allowing optimization of excavation sequences and support requirements; a more effective instrumentation and monitoring program; and improved construction details and related contract provisions.

Jan 1, 2007

By Bradford F. Townsend, Robin B. Dill, Richard M. Croswell

Innovative geotechnical construction techniques were used to construct three pedestrian tunnels under a building slab-on-grade to allow utilization of basement space for manufacturing. Tunnels were constructed using mining techniques through granular fill soils less than three feet below on-going sensitive manufacturing operations. Project design consisted of jet grout underpinning of exterior foundation walls and an arch of drilled-in grouted horizontal dowels for soil pre-support to limit ground movements during excavation. Permanent tunnel lining consisted of arched steel rib sets and invert struts supported on precast footings encased in cast-in-place concrete slab and side walls and a gunite arch.

Jan 1, 1993

By Adrian Coombs

The York Durham Sewage System (YDSS) Interceptor Tunnel Project is located in the Town of Richmond Hill, Ontario, Canada, just north of Toronto. Construction commenced in September 2006 and completion is planned for early summer, 2008. The project involved public and agency buy-in of construction technologies and methods that minimized dewatering, design and construction of sealed shafts with jet grout break-in and out blocks in order that Earth Pressure Balance (EPB) mode could be maintained by the Tunnel Boring Machine (TBM) during shaft entry and exit. This paper will discuss the advances that were made possible through the opportunity to apply and test these technologies in order to accommodate the aquifer and artesian conditions present on this project.

Jan 1, 2008

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By Jon Hurt

INTRODUCTION The entire scope of new facilities for Lake Mead Intake No. 3 includes a sub-merged intake structure, a deep tunnel beneath Lake Mead, a tunnel access shaft, Intake Pumping Station No. 3, and connections to an existing intake and water treat-ment facility, as shown in Figure 1. In March 2008 Vegas Tunnel Constructors (VTC), a joint venture of Impregilo SpA and SA Healy were awarded a $447m Design-Build contract by SNWA for a section of this work (Contract 070F 01 C1), including the 185 m deep tunnel access shaft, the 4.7 km long, 6.1 m diameter tunnel and the submerged intake. Arup, supported by Brierley Associates, is the Design Engineer for VTC. The scope of the work is shown in Figure 2. This paper will describe the design and construction on this contract, with a focus on the access shaft which is the most complete section of the work. The shaft is being sunk using drill-and-blast methods with the finallining placed as excavation proceeds. The shaft passes through a major fault zone, and extensive pre-excavation grouting for water control is required for much of the depth of the shaft.

By Andrew Peterson

The Maine Department of Transportation offered this challenging design-build project for a new, 12-span, bridge over the Kennebec River in Bath, Maine. This structure would be built to replace the existing Carlton Bridge connecting the village of Bath, Maine to neighboring Woolwich, Maine. The design build team of Flatiron Structures, Inc., and Figg Engineers, Inc., elected to design and build a segmental concrete bridge. Site conditions dictated that this bridge would be supported primarily on deep foundations. Case Foundation Company joined the project team in the winter of 1997 to install twenty-two, eight foot diameter drilled shafts. The drilled shafts were designed with 8' diameter, permanently cased shaft sections and 7.5' diameter rock sockets. Shaft lengths ranged from 20' long near the river's edge to 100' deep in the middle of the river. Rock socket lengths ranged from 12' to 30' deep. Two Osterberg Cell load tests were conducted on production drilled shafts. Figg Engineers utilized the results of the load tests to "fine-tune" the rock socket design during construction of the drilled shafts. Construction of the drilled shafts proved to be very challenging and called on every member of the design-build team to work together throughout the project. One of the most challenging aspects of this project was in the installation of the 8' diameter permanent casing and drilling of the rock sockets. Early in the project, it became apparent that the top of bedrock was broken and unstable. This condition limited the advancement of the permanent casing and the affect of a "seal" at the top of rock socket. As a result, as the rock socket was advanced, loose material spilled into the hole and stopped progress of the socket. In order to resolve this problem, the design-build team developed a redesigned drilled shaft which included the installation of a steel sleeve to seal off the unstable rock formation. Following installation of the sleeve, the rock socket diameter was reduced to 7' diameter and advanced additional length to achieve required design capacity. All drilled shafts were installed with equipment supported on floating barges. Water access, along with the long shaft lengths and very hard bedrock required the use of cranes and drilling equipment that far exceeded the requirements of typical drilled shaft projects. This paper will discuss the relationship between design, construction, and equipment utilization on this challenging design-build project. [ ]

Jan 1, 1999

By C. Y. Kao, Roger Y. Cheng, C. S. Hsieh

The mushroom-shaped Minghu power cavern located in central Taiwan is 21.2 m (W) by 40.5 m (H) by 127.2 m (L) and is designed to house 4 units of power generating-pumping equipment with a total capacity of 1,000 MW. This paper presents an introduction to the geological conditions at the cavern site; the rock mechanical tests undertaken; the design approach adopted; the construction method and sequence followed; and the instrumentation provided in the roof arch to monitor the behavior of the surrounding rocks. The measured data collected from the embedded instruments will be compared with those obtained from theoretical analyses and presented in this paper. Several technical problems encountered during the construction stage are covered and the solutions of these problems are also described therein.

Jan 1, 1983

By Gerald G. Griswold, Allan G. Provost

INTRODUCTION The Norad Expansion Project was located 10 miles southwest of Colorado Springs, Colorado, within Cheyenne Mountain. The expansion areas to be excavated would be adjacent to the existing underground Norad complex, which would remain in operation during the work on the expansion. The original complex had been constructed approximately eight years earlier and had been in full operation for approximately five years. Phase I, Excavation was awarded the Tiro Construction Corporation, a subsidiary of Harrison Western Corporation, Denver, Colorado, in the fall of 1970. Notice to Proceed was given to Tiro on 28 December 1970. The project owner was the U. S. Air Force, design was performed by the U. S. Corps of Engineers, Omaha District, who would also serve as the construction agency. [ ]

Jan 1, 1979

By J. Chae, D. Pecha, R. Andrews

The Henderson/ML King CSO Project is a major combined sewer overflow (CSO)reduction project for the Department of Natural Resources and Parks of King County, Washington. The central element of the project is the 3100 lineal feet long, 14'-8"diameter 42nd Ave S Storage/Treatment Tunnel. During the course of the project, the owner and consultants evaluated numerous elements of the tunnel including the alignment, geotechnical conditions, tunnel liner, and settlement monitoring requirements. The contractor utilized innovative shaft construction methods for the tunnel portals, and adhered to strict contract requirements in successfully constructing the tunnel. This paper provides an overview of the design and construction elements of the 42nd Ave S Storage/Treatment Tunnel that led to the successful completion of the project.

Jan 1, 2005