Search Documents

By Yoshiharu Tanaka, Toshiyuki Ichijo, Masaaki Yamamoto

We utilized electronic detonators (EDs) to investigate the effect of high detonator delay accuracy on overbreak, remaining rock damage, and surface smoothness, in comparison with that of long-period delay detonators (0.25 sec interval) PDs. The experiments were conducted in a deep mine, in a test site region composed of very hard granodiorite with a seismic wave velocity of about 6.0 km/see and a uniaxial compressive strength, uniaxial tensile strength, and Young's modulus of 300 MPa, 12 MPa, and 73 GPa, respectively. The blasting design was for a test tunnel excavation 8 m in cross section, with an advance per round of 2.5 m. Five rounds were performed, each with a large-hole cut and perimeter holes in a 0.4-m spacing charged with 20-mm-diameter water gel explosive to obtain low charge concentration. EDs were used in the holes on the perimeter of the right half, and PDs were used in all other holes.

Jan 1, 1995

By J. Hansen

This paper has been written for presentation during the Open Pit Mining Session at the SME Annual Meeting and Exhibit, Denver, Colorado, February 26 to 28, 2001. The paper addresses the application of automated monitoring of electric rope shovels to improve performance and blasting technique.

Jan 1, 2001

Several years ago, Hudco Industrial Products began experimenting with the idea of levitating a conveyor belt with a film of air, much like the puck on an air-hockey table. While conducting its research, the company found out that some Russian and Dutch companies attempted the concept during the 1970s. After studying those conveyors, Hudco determined that its design was better. The Hudco advanced air-supported conveyor consists of an air-tight plenum, or chamber, that runs the length of the belt. The topside of the plenum has a formed trough. It corresponds to the profile of conventional troughing rollers. Low-pressure air is provided to the sealed plenum from a low horsepower blower. This pressurized air is metered and released through the central portion of the trough and reacts against the underside of the belt. The differential pressure between the top and bottom surfaces creates the lift to support the loaded belt. Airtight covers are installed to seal the transported materials in the plenum trough.

Jan 1, 2002

By T. Weatherwax

As part of a strategic research initiative at UBC to design and evaluate integrated underground mining and mineral processing systems, work has been done to determine how to utilize the coarse rejects of pre-concentration in the underground environment. An amenability study for nine orebodies from four of Xstrata Nickel?s Ontario operations evaluated both processing and waste disposal methods. The utilization of the rejects as a high quality backfill with minimal binder requirements has been identified as the preferred disposal method. Fill mixes utilizing the rejects in combination with classified tailings, full tailings, and cement were developed based on the geotechnical properties of the rejects. The mix designs were examined for both strength and rheological properties. The paper will present the results of the pre-concentration testwork, the design and strength testing of various mix designs for rejects from the nine ores and presents a conceptual design for an underground pre-concentration system based on this test work.

Jan 1, 2008

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

The commercial application of electrolysis to zinc sulphate solutions for the production of metallic zinc is a development ·of the past twenty years. Earlier attempts failed to give satisfactory results, chiefly because certain harmful elements were either not recognised as being present in the solution, or, if recognised, suitable methods of removal had not been developed. The electrodeposition of zinc from zinc sulphate solution is extremely sensitive to the influence of a great many factors, all of which appear to be closely inter-related.Some of these factors tend to minimise the necessity for a high degree of purity of the solution, while other factors aggravate the harmful nature of certain impurities.The relationship existing betweBn the various factors in zinc electrolysis makes a general discussion of the injurious effect of impurities very difficult since, under one set of conditions a given concentration of an impurity may be of minor: importance, where its under another set of conditions the same concentration of that impurity may prove dangerous to successful electrolysis.

Jan 1, 1934

The usual metallurgical, engineering and administrative activities associated with the handling and smelting of ores, and the subsequent handling and treatment of the products of smelting, present also problems of hygiene that engage the earnest attention of executives in all well-managed concerns.Again, associated with the employment of any considerable number of men, there is always present the problem of accident prevention.INDUSTRIAL HYGIENE.In the earliest records of lead min.ing and smelting there are references to the injurious effects of lead oh the health of the employees, and, with the advancement of medical science, lead poisoning has been the subject of many works by various authorities in many countries.Moreover, in practically every civilised country, there are laws governing the conduct of the lead industry, and in most cases these laws stipulate that employees shall receive compensation for disability caused by lead poisoning.This provision gives the problem an economic aspect. Apart from the legal and the economic aspects, however, there is the humanitarian aspect, which implies that the...

Jan 1, 1937

IN presenting a'description of milling and treatment methods at the Waihi mine, it is advisable to first traverse a good deal of the past history of the mine, and show the various steps which have led up to present-day practice. The record of the company is one of steady, solid advancement, both in metallurgical and financial results. This is illustrated by the following figures, dating back from 1897...

Jan 1, 1912

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

By M. L. Smith, G. Karunatillake

Lead-zinc production at MIM, Mount Isa includes three mines, a lead concentrator, zinc filter plant and lead refinery. Lead production is vertically integrated with lead-silver bullion shipped from Australia to London for refining. Zinc is sold as a concentrate. All three mines have reached varying states of maturity mining a multitude of orebodies having significant variation in grades and metallurgical recovery for three metals. Based on current levels of measured resources, the remaining project life is at least ten years. The objective is to schedule production over the life of all three mines so as to maximize the present value of the complex. Additional scheduling complexity arises out of the implementation of long-term schedules, capital expansion projects for both mining and processing, the presence of substantial inferred reserves and interactions with MIM copper production. A large-scale, time-dynamic, life-of-complex Mixed Integer Program (MIP) production schedule was formulated to optimize lead/zinc cash flow based on a detailed life of project production scheduling study. The requirements for such a study are detailed herein. The operational feasibility of the MIP solution is compared against a non-optimal approach to strategic life-of-mine scheduling. The strategic planning emphasis placed on the MIP is compared to the implementation of a life-of-mine schedules at Mount Isa using spreadsheets and other popular commercial mine schedulers.

Jan 1, 2003

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

A possible process for extracting tellurium and antimony from a residue generated in alkaline sulfide leaching of telluriumbearing alkaline skimming slag was proposed. The central composite design was employed to define the optimal leaching conditions for tellurium and antimony extractions from the residue sample. Using a 23 factorial matrix, the best performance for tellurium and antimony extractions (96.36% and 99.64%) were obtained at 175 g L−1 Na2S concentration for 80 °C during 60 min. The notable degree for influencing tellurium and antimony extractions was leaching temperature, Na2S concentration, and leaching time. The analysis of variance results indicated that the regression model was significant and suitable to be used for the optimization of independent variables within the range. The model was validated under optimal operating conditions based on the experimental design results. Antimony and tellurium in the leach liquor were separated and recovered by H2O2 oxidation followed by Na2S-Na2SO3 reduction. 98.93% of antimony was precipitated selectively during H2O2 oxidation, while 95.06% of tellurium was precipitated during Na2S-Na2SO3 reduction. NaSb(OH)6 and elemental tellurium was obtained as the product.

A review of historic mining information and geological literature pertaining to the Alpine Mine, Lyell Goldfield has been completed. As a result of this work the Alpine reef is inferred to be associated with an upright anticline with a sub-horizontal axis. Structural profiles prepared from limited underground data indicate that the reef is subparallel to the eastern limb of the anticline and cuts across the western limb. Reassessment of structural mapping completed by the New Zealand Geological Survey indicates that Greenland Group metasediments within the Lyell Goldfield are folded into a series of opposed assymetic folds with sub-horizontal axes. It is suggested that the anticline which harbours the Alpine Reef is located on the axis of a synclinorium. Along the western limb of the synclinorium the subsidiary folds have steep west dipping limbs and shallow east dipping limbs (western sense of assymmetry) whereas shallow west dips and steep east dips are typical of the eastern limb. The notion of quartz mineralisation occupying the axis of a synclinorium is contrary to the situation in the Reefton Goldfield where quartz mineralisation is affiliated with folds associated with an anticlinorium. Historic mine data reveals that below No.4 Level the quartz-gold mineralisation, in the Alpine Mine, occupied a steeply dipping ore channel. The strike of the channel was to the northwest and within this structure the are shoots plunged to the north at approximately 40¦. Archival mine plans show that two quartz bodies, the North and South Blocks, were present at No. 4 Level. Although the North Block was followed down to No 14 Level (530 m vertically below the surface outcrop) the South Block was only mined as far as No 7 Level. Sampling on No 7 Level together with the results of trial mining suggest that the grade of quartz underfoot in South Block is low. Information from the Mines Statements and mapping undertaken by the Gold Prospecting Scheme reveals that faulting had a profound influence on the intregity and extent of the Alpine Reef. The reef occupies a Inajor shear zone but little is known about it. It is also apparent that below No 7 Level the reef was progressively shattered by faulting and this may be the chief reason for the decrease in grade in the lower levels of the mine. No substantive facts are available about wall rock alteration effects adjacent to the Alpine Reef Still this is not surprising considering that comments on the mineralised pug envelope and breccias adjacent to the mined quartz shoots at the Globe - Progress Prospect were omitted from contemporary publications. In spite of this the existance of sulphide bearing reef casing lithologies cannot be completely dismissed since 9.15 m of 'reef track' has been reported in Reids No 2 Level.

Jan 1, 1996

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill, considering mainly the role and specifications of the fill used but including û brief description of fill preparation and placement. Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. Results of a fill research program conducted by the author in Mount Isa since early 1968 are presented, involving both Portland cemented hydraulic fill and alternative, cheaper, additives for cementing hydraulic fill.

Jan 1, 1971

By V. F. Swanson

As part of the Bureau of Mines titanium resources examination program, samples of altered rock (saprolite) and unaltered rock from the Roseland anorthosite near Roseland, Nelson County, Va., were tested for amenability to beneficiation by flotation. A flotation technique was developed to produce bulk concentrates of ilmenite, rutile, sphene, and leucoxene. It was necessary to first float apatite using oleic acid as the collector, in an alkaline pulp with dextrine as a titanium mineral depressant. The titanium minerals could then be floated from the apatite tailing, using fluosilicic acid to depress the remaining apatite, morin to depress ferromagnesian minerals (when present), and oleic acid as the collector. A bulk titanium mineral concentrate, analyzing 66.0 percent Ti02 and 0.08 percent P205, was obtained from a sample of the unaltered rock which contained 5.45 percent TiO2 and 2.81 percent P205. Overall recovery in the concentrate was 47.1 percent of the total TiO2 in the ore. About 55 to 65 percent of the saprolite sample was clay and was removed by attrition scrubbing and decantation. The apatite prefloat procedure was applied to the saprolite sands; subsequent titanium mine: 1 flotation recovered 72.2 percent of the Ti02 in a bulk concentrate containing 65.1 percent TiO2 and 0.20 percent P205.

Jan 1, 1962

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1982 (October 1, 1980 -September 30, 1981) under its Minerals Health and Safety Technology program. Contingencies may require that a significant port ion of the program be deferred into fiscal year 1983. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the systems technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1981

By Mark I. Copeland

A study was conducted to determine if commonly used alloying additions or coating materials can prevent the formation of a liquid-copper phase during the reheating of copper-containing steels. If so, the tendency of such steels to surface-crack during hot-working might be eliminated. Steel specimens were scaled by heating them either isothermally or in a programed manner that simulated industrial furnace practice. Metallographic examination of the heated specimens showed that molten fayalite (Fe2Si04) completely prevented the formation of liquid copper at the surface. Fayalite, which melts at 2,200° F (1,205° C), was formed by internal oxidation of the silicon contained in the steel. By forming complex molten oxides, coatings of borax glass were also effective in preventing the occurrence of liquid copper at the steel surface.

Jan 1, 1972

By Charles E. Whieldon

Data on the oilfields in Mahoning, Columbiana, Carroll, Jefferson, and Harrison Counties, Ohio, were collected from scattered sources and compiled to make the information readily available to operators who may be interested in conducting secondary-recovery operations in the area. General geology, oil production, oil-productive acreage, core data, reservoir calculations by townships, and miscellaneous data and reference material are presented.

Jan 1, 1965

Mineral deposits of the central New Guinea region (Gunung Bijih, Ok Tedi, Mount Kare, Porgera, Frieda River) and of southeastern New Guinea (Wau-Edie Creek, Wafi, Hamata, Hidden Valley, Tolukuma, Misima) are associated with hot, forceful intrusions of magma of mantle origin that penetrated thick Precambrian and Palaeozoic continental crust. The interaction of high- temperature melt with continental crust, and the differentiation of melt while in transit through thick crust, may be factors in generating ore. Mineralised intrusives in central New Guinea are a result of Neogene- Quaternary magmatism and were emplaced in a foreland thrust belt environment, a setting similar to the (mineralised) Laramide intrusions of southwestern USA. In both cases, central New Guinea and the Laramide, magmatism is not obviously subduction- related. Mineralised intrusives in south- eastern New Guinea (Wau-Edie Creek, etc.), also, are in a thrust belt setting, and are not obviously subduction-related. The association of. gold in southeastern New Guinea with a second (Pliocene) phase of igneous activity, rather than with earlier (Miocene) activity suggests that re-working by successive intrusions may be a factor in localising ore. This is seen, also, in the Bismarck-Solomon islands region where the richer deposits are associated with later (Pliocene) intrusives rather than with earlier (Eocene-Oligocene) intrusives. Unlike the mainland mineral deposits, those of the Bismarck-Solomon islands are clearly subduction-related.

Jan 1, 1991

By W. L. Dare

Tri-axial strains in pillars, created by pillar robbing, were measured in an experiment at the Dysart No. 1 uranium mine near Grants) New Mexico. At this mine, room-and-pillar stoping is used on the advance, and pillars are recovered on the retreat. The are deposit is, for all practical purposes, horizontal. Measuring devices were installed in pillars approximately 90 to 200 feet from the break line, and strains were recorded over a 4-to 6-week period. The measurements indicate that, in general, the algebraic magnitude of vertical strains increased, and the horizontal strains decreased, in turn, indicating that vertical (or near vertical) loads on the instrumented pillars lessened as pillars were recovered.

Jan 1, 1962

By Alan A. Campoli

The U.S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996