Search Documents

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

By N Merry, T Cocks

The mineral exploration industry is increasingly aware of the importance of the relationship between mineralogical data and geochemical assay results. However, until recently, the cost and time constraints of most techniques for analysing alteration mineralogy have precluded detailed alteration studies. These impediments have been reduced by the development of the Portable Infrared Mineral Analyser (PIMA), a field portable infrared spectrometer that allows rapid (in field) and cost effective analysis of alteration minerals including subtle variations in mineral crystallinity and composition.   A major application of this technology is in mapping mineralogical variations within hydrothermal alteration systems. Using actual case study examples this paper introduces two approaches to using the PIMA data: 1. for directly mapping alteration systems and using the PIMA data to provide vectors to mineralisation, and 2. for establishing empirical relationships between geochemical data and PIMA spectral data. These applications demonstrate that this technology can be an invaluable tool for targeting and mapping alteration and mineralisation.

Jan 1, 1995

By K. Drescher

Excavations in deep level hard rock mines show rheological or time-dependent deformation responses to mining-induced stresses. These are generally not as dramatic as those seen in soft rock environments, such as potash and salt mines, but these deformations can nevertheless become substantial in time. It is usual to see total excavation closure at a much earlier stage than predicted by numerical models, and real-time measurements underground have confirmed that closure takes place on a more-or-less continuous basis, with highest closure rates observed after a blast and then slowly diminishing with passing time. This paper describes laboratory tests to determine the time-dependent response of hard rocks to loading, the results of the tests, and then quantifies these effects to explain the time-dependent phenomena observed underground. The primary intention of this work is to help explain the various time-dependent deformation processes around typical deep level hard rock tabular excavations. Three mechanisms were investigated in two typical hard rock types present in the deep level gold mines in South Africa, namely Ventersdorp Lava and Elsburg Quartzite. Uniaxial compression creep studies were done as the first part of the study followed by shear creep studies on discontinuities where crushed lava and crushed quartzite as well as a natural gouge were used as infilling. The last part of the study consisted of triaxial post-failure relaxation tests. The compression creep tests and the triaxial post-failure relaxation tests showed that the amount of energy dissipated by the lava is significantly less than for quartzite. For mines operating at depths greater than 2000 m the implication is that the lava must show a greater rockburst-proneness than the quartzite. Since the lava shows a lower post-failure stress relaxation, it can store sufficient energy for multiple rockbursts, which is seen in the clustering of multiple seismic events in the deep level mines. This study provides the first data available for energy change calculations in fractured rock masses, and provides the first general indications for rockburst intensities ahead of active mining faces.

Jan 1, 2003

By A. N. Clay

In recent times, there has been criticism of the minerals industry over the lack of quantifiable boundaries between inferred, indicated, and Measured resources. A recent initiative through the United Nations aims to try to converge the mineral resource classification systems. Since the oil and gas industry uses a probabilistic approach to defining reserve boundaries, it is appropriate to introduce a similar statistical methodology for minerals. The Venmyn Variance Tower has been developed based upon traditional statistics to utilize historical and ongoing information in order to quantify variance of geological and chemical parameters and the boundaries and logic for quantitative mineral resource classification. It is proposed that a less than 50% variance from the mean of all sample parameters is required to achieve the classification threshold to define an inferred Resource whereas between 20-10% is needed for an indicated Resource and less than 10% variance from the mean is needed to declare a Measured Resource. These limits are similar to those used by the oil and gas industry, and it is suggested that these thresholds be adopted as an industry standard to ensure consistent quantitative reporting. While this process is intended to use statistics of an orebody to provide quantifiable and defendable boundaries, it cannot be carried out unless the geology of the mineral deposit is understood and the borehole samples can be categorized into appropriate populations for which the statistics are valid. This means that competent geologists are always required to work with and understand the implications of the Variance Tower results. This paper is intended to form the basis of a series of publications that establish a process to take mineral projects along a quantifiable and logical development path. Hence, no specific field example of the practical application of this process is given here.

Jan 1, 2012

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

By S. Mostaghel, S. Nicol, M. Y. Solar

Once upon a time, the process engineer developing the design criteria for a new saprolite ferronickel smelter had it easy: most ores were around 2.5% Ni, with a Fe/Ni ratio of 4 to 5 and a SiO2/MgO ratio of about 1.6; to use the French word: garnierites. The ferronickel grade selected was the conventional 20 to 25% Ni and the impurity levels could be predicted from well established [C], [Cr] and [Si] vs (FeO) graphs. However the process engineer can no longer depend on statistics to design smelters: Ni grades are decreasing while the goethite contents are increasing; SiO2/MgO ratios vary from 1 to 3; and Al2O3 concentrations are reaching levels that cannot be ignored. Mechanistic models must be developed to select or predict essential parameters such as kiln and furnace reductions, ferronickel grade, slag losses, metal and slag liquidus, operating temperatures, etc. But these models must be simplified so that they can be used on a routine basis; and they must be calibrated against a wide range of commercial operations in order to yield the most realistic predictions possible. The present paper proposes one possible approach, using FactSage as a basic source of thermodynamic data. The predictions thus obtained are compared to actual performance for two well documented operations, as well as to the predictions made with other tools that might be more accessible.

Jan 1, 2014

The Barmac autogenous crushing mill is one of the most successful new comminution technologies to become available to the mining and industrial minerals industries in this decade.   The Barmac autogenous crushing mill is an innovative Vertical Shaft Impactor which operates in essence like a high intensity dry ore centrifugal pump with the reduction occurring primarily as a result of high velocity rock to rock impact in a fully rock lined crushing chamber.   With applications in a wide range of mining and industrial minerals operations the Barmac autogenous crushing mill presents an opportunity to enhance reduction and liberation whilst providing many cost savings and production increases in new and existing plants.   This paper briefly describes the operation of the Barmac autogenous crushing mill and reviews its benefits.

Jan 1, 1990

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

By P Blattner

The Late Miocene gold-silver bearing epithermal system at Waihi has some close similarities in its paleo-thermal and geochemical structure with modern, volcanic-hosted geothermal systems such as Ohaaki-Broadlands. At Waihi an extensive braided quartz vein system is enveloped by hydrothermally altered andesites with minor tuff breccias and tuffs. A main stage of vein filling consists of multiple phases of chalcedonic quartz and fine to medium grained quartz, which are accompanied by pyrite, sphalerite, galena, chalcopyrite and acanthite below the base of oxidation. Platy calcite is present locally. Fluid inclusion studies indicate that the main stage quartz was deposited at temperatures of 189¦-273¦C from dilute (Tm of -0.1 to -1.0¦C) fluids that were locally boiling. Homogenisation temperature Th versus Tm data points lie within the field enveloped by dilution and boiling/gas loss paths determined for the Ohaaki geothermal field, and indicates that the parent hydrothermal fluid for the Waihi epithermal system had a similar composition to that at Ohaaki, ie 0.2 wt% equiv NaCl and 3.3 wt% equiv CO2. The hydrothermal alteration mineralogy and the isotopic composition of vein calcite indicate that the hydrothermal fluid contained relatively high concentrations of CO2 , as at Ohaaki. Oxygen isotope analyses of main stage quartz range from 6.1 to 11.6 %0 and of vein calcite from 2.29 to 9.4%0. Calculated d18Owater values for the hydrothermal fluid that deposited the main stage quartz range from 2.0 to -5.7%0, with a trend to less negative values with depth. They are similar to those in the deep chloride fluid in active geothermal systems with a substantial fluid throughput. A high fluid throughput at Waihi system is also evident from the extensive high intensity hydrothermal alteration and large volume of quartz deposited in the vein system.

Jan 1, 1995

By G. W. Jones

In a previous report,6/ results were given that showed the amount of natural ventilation in a manhole having a capacity of 74.1 cubic feet when the number of ventilation openings in the cover was varied from no openings to a maximum of 48. The result s showed that the ventilation (air changes per day) in the manhole was proportional to the area of the openings in the cover, and also that the number or area of the openings was the factor that chiefly affected the ventilation.

Jan 1, 1937

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation of a coal mine. The average thickness of coal seams mined in the United States has changed very little in the past 40 years. The first measurement of thickness of bituminous coal and lignite seams was made for 1920, when the average thickness was 5.3 feet.4/ The average thickness for later years was as follows: 1945, 5.4 feet; 1950, 5.3 feet; 1955, 5.2 feet; and 1960, 5.5 feet.5/ Table 1 includes data on number and production of bituminous coal and lignite mines classified by I-foot intervals of seam thickness mined in 1920, 1945, 1950, 1955, and 1960. Though bituminous coal and lignite are mined today from seams of exceedingly variable thickness -less than 2 feet to more than 50 feet - a large majority of the production, 62 percent in 1960, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1962

By C. J. Bise

One area of study for the Coal Mine Injury Analysis project was to illustrate how loss control can be used as a foundation for mine safety training. After an initial review of the principles of loss control, the instruments often used for worker/worksite appraisal, such as incident reporting, analysis, and investigation, workplace observation, worksite inspection, and safety audits and checklists were evaluated for their effectiveness. The findings were then applied to the continuous-miner worksite at several mines to modify the techniques for use in a highly dynamic man/machine work environment. Before the information gathered from the review of the various continuous-miner worksites was presented at the annual retraining sessions at five mines, a trainability analysis procedure was developed to separate training shortcomings from those problems resulting from improper equipment design or unsatisfactory working environments. Also, several microcomputer-based training programs were developed to aid in conveying the loss-control concepts to the trainees. Finally, the results from the implementation and evaluation of the loss-control-based training programs were documented, including the complete training script for one of the case-study mines. The procedures outlined in this study will aid mine training specialists in developing focused, pro-active accident-prevention strategies and training programs that are based on sound loss-control principles.

Jan 1, 1993

By J Deen, P Sterk, W Forsyth

Homestake Mining Company has made a firm commitment to develop a functional and cost effective perimeter blasting program. The goal of the program is to develop smooth, sound walls in all development ends. A good perimeter blasting method will improve safety, reduce waste rock handling, allow easier support installation and reduce scaling time. All the benefits will contribute to an overall reduction in total development costs.

Jan 1, 1997

By Joseph J. Diehl, Brian B. Khalighi

This paper discusses the Queens Water Tunnel, No. 3, Stage 2, being driven by a new Robbins High Performance (HP) Tunnel Boring Machine (TBM).The paper is divided into four sections. In the INTRODUCTION section, a short overview of the scope of the project is presented. In the GEOLOGY section, the geological condition along the tunnel drive is briefly introduced. The TBM DESIGN section discusses the various design criteria and the resulting machine specifications. The paper concludes, in the TBM OPERATION section, with a case history describing the tunneling operation from start-up to the time of the writing of this paper.

Jan 1, 1997

By Patrick O. Shires, Harry W. Schnabel

With stable building sites becoming scarce in the greater San Francisco Bay Area, the new Summit Senior Care Facility is being built into the side of an unstable hillside adjacent to the San Ramon Regional Medical Center in San Ramon, California. This hillside has had a long history of instability and the site of the new Senior Care Facility required excavation into both a historic old landslide and a more recent active landslide. After a thorough geotechnical study, it was concluded that the best way to build the new facility would be to construct a tied-back retaining wall in the area of the old landslide, since it extended off-site onto two adjacent properties, and remove the active landslide and replace it with compacted fill before cutting into its toe area with an additional tied-back retaining wall. The design was further complicated by the proximity of the site to several active faults. In the area of the old landslide, the combination of an ascending slope behind the wall, landslide forces and seismic forces resulted in total design pressures between 365 to 4,575 PSF for a wall with a maximum height of 30 feet. The wall for the old landslide was constructed by first drilling and placing steel soldier piles in concrete. The tip of the soldier piles extended a minimum of 12 feet below the landslide plane that was up to 36 feet below the bottom of the wall. Permanent double corrosion protected tiebacks were then installed through the soldier beams and anchored below the slide plane. A shotcrete facing was then installed on the face of the wall. BACKGROUND The site of the Summit Senior Care Facility is located on the southwest flank of Mount Diablo adjacent to San Ramon Valley which is characterized by gently rolling hills. The San Ramon Valley Regional Medical Center, which opened in 1990, is located to the north and an existing church is located to the southwest. There are also private residences located to the southeast. The site is shown in Figure 1. Numerous faults run close to the site, the most significant of which are the Calaveras and Pleasanton faults. The site has also had a long history of slope instability and has been the subject of numerous investigations. Studies conducted in 1979 and 1984 concluded that there was a landslide in the area and recommended that a buttress shear key be constructed between the subject site and the existing church for a sewer main as well as removal and replacement of the head area of the old landslide to stabilize the hospital site. While two previous geotechnical studies in 2008 and 2016 identified slope instability, they did not recognize the genesis and limits of the old landslide on the western portion of the site or the limits of the active landslide on the eastern portion of the site.

Jan 1, 2018

By Karsten Beckhaus

"Abstract Tremie concrete for special geotechnical works needs special properties, especially during the casting process. Today’s execution standards for bored piles and diaphragm walls, EN 1536 and EN 1538, as well as the draft version of concrete standard EN 206, all comprise regulations for deep foundation concrete which have not been changed for decades. Considering the recent development in concrete technology at the same time and its actual state-of-the-art, it is essential to develop new normative specifications and specification requirements.GeneralTo allow the required integrity and quality after placing and hardening, concrete for structural elements like bored piles or diaphragm walls, used as foundations of high-rise buildings or as retaining structures for large and deep building pits, must have adequate workability and stability.In addition to requirements on mechanical properties and on durability, both of which have increased within the last decades, concrete must be suitable for being cast in deep or extremely deep excavations, see figure 1. Today’s specialist foundation engineering machinery makes it possible to drill or cut down to in excess of100 m depth. Concrete technology has developed and allows the use of high performance concrete for deep foundations. But is this capability represented by actual regulations?It has become very common for the industry to supply or use concrete with low water cement ratios, nevertheless highly flowable and set-retarded for several hours if needed. Very low water cement ratios allow design strength of 60 MPa or higher (Larisch, 2011), and a very low porosity which is required for a long service life in aggressive conditions, e.g. by chlorides.To achieve best performance, it is obvious that the concrete must completely fill the excavation and fully embed the reinforcement. As vibration of deep foundation concrete is (usually) not allowed and was anyway inefficient, deep foundation concrete must be designed to self-compact under hydrostatic pressure. Generally, it must be considered that after placement the concrete’s quality cannot be influenced anymore. Therefore, both the pouring procedure and the concrete quality must be adequate."

Jan 1, 2014

By G Eastwood, C Joyce, P Ryan, G M. Johnston

Over the years, predictive techniques for Acid Mine Drainage (AMD) and the natural processes affecting acid generation have received considerable attention. Less emphasis has been placed on the sampling strategy and the integration of testwork results with the geological data base. The sampling strategy employed and the development of a geological model to determine the spatial distribution and volume of acid producing material are often crucial for developing cost-effective containment and mitigation measures. The geological model provides a link between the occurrence, timing, destination and placement of mined waste rock. Careful and accurate interrogation of a comprehensive geological database provides this linkage. The AMD testwork program at Cadia in NSW has been designed to identify the temporal selective handling requirements that will be required during operation. Sampling involved collection of representative combinations of all waste rock types identified within an extensive geological database. These samples were subjected to static, kinetic and accelerated weathering predictive tests. Preliminary results have been used to construct a waste block model for the deposit that identifies the quantity and distribution of acid producing material. Integration of the block model with the mine scheduling determines when the material will be mined.

Jan 1, 1996

By Fred W. Brackebusch

"The use of paste technology for surface tailings disposal may offer economic, technical, safety, and environmental advantages for both underground and surface mining operations. Paste is a non-Newtonian fluid having some shear strength during transport and placement. The strength is augmented after placement by consolidation, water loss, and by addition of chemicals. Economical dewatering systems are necessary to the success of surface paste tailings disposal. In an underground mine, the paste backfill plant can produce paste for surface disposal about 50% of the time because only about 1/2 of the tailings are needed for backfill. The distribution of paste to the surface stack involves expensive pumping equipment and thus a nearby location of the stack is desirable. The viscosity of paste can often be manipulated by modifying pH. Placement of the paste in a designed stack configuration depends on topographic and climatic factors as well as paste properties.INTRODUCTIONThe use of paste technology for mine backfill is becoming accepted for underground mines mainly because of ground control and economic reasons. Paste technology is just starting to be applied for tailings disposal with only a few hardrock metal mines worldwide using the technology; however, it has been used extensively for red mud disposal in the aluminum industry. The disposal of dry tailings is very attractive from environmental and safety points of view because of limited water which might potentially escape and pollute river systems. Dry stacking systems, however, are expensive because of filtration and truck transportation costs. Paste can be produced from most tailings streams by special types of thickeners. Furthermore, it can be transported in pipelines, therefore paste technology may be more economic than dry stacking but still have some of the major advantages. Understanding of paste technology has improved through experience with operating underground backfill systems in recent years and because of testwork and research programs by mining companies, consultants and equipment vendors. Thus we may be on the verge of taking a new look at tailings management using paste technology."

Jan 1, 2002

By R Yang, M Lownds

This paper reports studies showing the effects of delay scatter on the peak particle velocity (PPV) of blast vibration using a multiple seed wave (MSW) vibration model developed in recent years. The case studies also show the advantage of accurate delay timing on frequency control of blast vibration. The site parameters used in one of the studies are from a case in which the MSW model has been tested and confirmed to yield accurate predictions. This study uses an open pit blast design and a tunnel design in which blast vibrations using electronic detonators are compared with those from pyrotechnic detonators. Mean peak particle velocity (PPV) and the 97.5% upper bound PPV are compared. It is found that both these values increase significantly with the increase of the coefficient of variation of the site parameter. Using an open pit blast design, the modeling shows that electronic initiation shifts vibration energy to the expected frequency for a selected point of interest. However, for the same design of nominal initiation timing pyrotechnic detonators fail to shift vibration to the expected frequency due to its large scatter of timing.

Jan 1, 2011

By Sharpe E. J

The Triton lode is a schistose feldspar biotite chlorite rock with quartz, carbonate, pyrite and some pyrrhotite. Its more chloritic sections strongly resemble the enclosing greenstones, its more feldspathic portions are indistinguishable from the flne-grained phases of the porphyry dyke into which the southern extremity of the ore body merges. The ore body' has a length of 880 ft. and an average width of I2t ft.; in places this widens to as much as 30 ft.The average dip is 85° west and pitch of the ore shoot 75° south.METHOD OF SAMPLING.With the exception of a limited amount of channel sampling (a reference to which is made elsewhere in this paper) all the sampling is by chip sample.The samplers use a hammer weighing approximately 11 lb. and chip directly into the sample bags. Sampling is generally carried out over 3-ft. sections and portions thereof to the nearest half foot-thus a face 8t ft. wide is divided up into two sections of 3 ft. each and one section of 2 ft.-no measurements of less than 4 ft. are used and calculations are all in feet and dwt. per long ton.In the oxidised stopes wp.ere the lode is much narrower, .i.e., 6 ft., sampling is over 2-ft. sections. All borehole samples are over 2-ft. sections, this corresponding approximately to steel changes.(a) DEVELOPMENT SAMPLING.Driving.-This is done by following the east wall and each face is sampled-this corresponding to an advance of 5 ft. If the full width o,f the lode is not exposed boreholes...

Jan 1, 1938