Search Documents

By A. Farnoud

Thousands of miners, construction workers, and truck drivers are exposed to diesel exhaust particles. Diesel Particulate Matter (DPM) is a probable human carcinogen and stringent occupational and environmental standards have been established or are planned worldwide. Modifications in fuels and diesel engine designs have reduced emissions, but may not be enough to comply with the tightest standards. Post-combustion aftertreatment devices are likely necessary for many engine operators. However, even the most common and well studied aftertreatment devices fail from time to time. The objective of this study was to design, construct, and test an electrostatic aftertreatment device to treat DPM. An electrostatic precipitator (ESP) was designed and constructed to capture DPM from diesel exhaust, and different configurations were tested to optimize its performance. DPM was produced by a 6 kW diesel-powered electric generator and directed to the ESP through a short section of galvanized steel pipe after the muffler. Number and mass removal efficiencies were measured with a condensation particle counter (CPC) and by sampling through a stainless steel cassette and collecting the DPM on Teflon filters. Particle size distributions were measured with and without control using a 6-stage cascade impactor. The experiments were performed with the engine running at idle and also at medium load. The results show that our first generation ESP provides 60 percent mass removal efficiency, and up to 80 percent number removal efficiency. Power consumption was generally low, about 20 to 30 watts, to achieve these levels of performance.

Jan 1, 2009

By S. Jiansheng, H. Nakayama, D. Lu, A. Wang

ABSTRACT: New techniques and methods for 3D geo-mechanical model test are presented in this paper. The new model material NIOS with high density and low cost; the so-called DPSS (Discrete Principal Stress Surface) loading concept, the loading and monitoring system for the generation of the 3D initial stress field of the model test, also the special techniques and apparatuses for modelling the excavation of caverns located deep inside the model material, are developed and introduced. By adopting those new techniques, a very large 3D geo-mechanical model test with high comparability for a newly designed underground powerhouse has been successfully fulfilled. Key Words: 3D model test, underground group caverns, excavation process modeling. ZUSAMMENFASSUNG: Neue Techniken und Methoden für 3D geomechanischen Modellversuch wurden in diesem Artikel vorgestellt. Ein neues Modellmaterial mit hocher Dichte und niedrigem Preis, ein sogenanntes DPSS (Discrete principal stress surface) Ladenkonzept, ein Laden- und Überwachungssystem für die Erzeugung des 3D primären Spannungsfelds und überdies spezielle Techniken und Maschinen für das Ausbruch der tief in dem Versuchsmodell liegenden Kaverne wurden entwickelt. Bei Anwendungen dieser neuen entwickelten Techniken wurde ein sehr großer 3D Modellversuch mit großem Maßstab für ein geplantes unterirdisches Kraftwerk erfolgreich durchgeführt. Stichworte: 3D Modellversuch, unterirdischen Gruppekaverne, Ausbruchsmodellierung Résumé: le test de modèl de Nouvelles techniques et méthodes pour la géo-mécanique 3D est figuré dans ce papier. Le nouveau modèle de matériels NIOS avec la haute densité et le coût bas; la conception proposée de chargement DPSS (Discrete Principal Stress Surface), le système de chargement et de moniteur pour la génération de champs de stress initial du test de modèle, ainsi que les techniques et appareils spéciaux pour modeler les excavations de cavernes profondément localisées dans l’intérieur du matériel de modèle, sont développés et introduits. A travers l’adoptation de ces nouveaux techniques, le test de modèle de la géo-mécanique très large 3D avec la haute comparabilité pour actualiser une nouvelle étude de la centrale électrique sous-terraine a déjà accompli avec succès. Mots de clé: test de modèle 3D, groupes de cavernes sous-terraines, processus de modèle d’excavation

Jan 1, 2003

By J. F. Breedis

The stabilization of austenite in Fe-Ni alloys against martensitic transformation after reversion has been attributed' to the lattice imperfections remaining from previous transformation. More recently, however, such stabilization has been associatedzy3 with compositional changes which occur in martensite during slow heating. Dislocation arrangements in deformed austenitic stainless steels strongly influence transformation to martensite on quenching.4 Therefore, it is of interest to observe the transformation behavior of stainless steel after reversion, especially since previous studies have been confined to Fe-Ni alloys. The transformation-product morphology also differs in the two iron-alloy systems;6 plate martensite forms in the latter while stainless steel transforms to lath-type martensite. Samples of Fe-16 wt pct Cr-12 wt pct Ni (maximum C + N = 0.005 wt pct, 0 = 0.02 wt pct), prepared by vacuum melting and casting from high-purity components, were annealed at 900°C for 24 hr, after cold rolling to produce a 40-p grain diameter. The M, temperature of this alloy is -80°C and samples are fully austenitic after annealing. The amount of martensite present after quenching, annealing, and requenching was determined magnetically, to within 0.01 wt pct, using a vibrating specimen magnetometer. Nearly 14 pct of martensite forms during the initial quench in 1 min at -196°C. Two-min and 2-hr anneals were done in air and in evacuated quartz capsules, respectively. All specimens were electro-polished before making the magnetic measurements.

Jan 1, 1967

By E. C. Westman, F. J. Shreve

This paper presents the design and construction of a multi-channel geophone array that improves tomographic imaging capabilities in both surface and underground mines. Especially important in the design of the array is sensor placement. Three issues related to sensor placement are addressed in this paper: 1) sensor placement in long, horizontal boreholes, 2) development of simple, robust, MSHA-acceptable clamping unit, and 3) orientation of the geophones within the borehole. Improved imaging capabilities will produce energy, environmental, and economic benefits by increasing exploration accuracy and reducing operating costs.

Jan 1, 2002

By P. Rostami

It is important to study the ventilation system in order to better design and control of the working environment in deep underground mines. With increasing depth, heat, and humidity performance may be reduced and impair the attention of workers. The purpose of this paper is to apply a complex; development-end model configured in the MULTIFLUX program, developed at the University of Nevada, Reno, USA. The MULTIFLUX development-end model template has been benchmarked against measurement results from two UK coal mines in previous studies. The present study is a test of MULTIFLUX application in a metal mine. The model incorporates the simulation of the air flow field in the drift and the auxiliary air duct; simultaneous heat and humidity transport from the drift wall; heat and mass exchange between the air in the drift and the ducts; and the evaporation of process water and/or condensation of vapor as governed by the psychometric conditions. The results are compared with field data, measured at the Lucky Friday Mine (LF) in Idaho, USA, an underground mine and also shown between the results from the MULTIFLUX-based model, and those from another program, Kduct, developed at the Kyushu University in Japan.. Gao, K. Uchino & M. Inoue Fukuoka, Japan (2002)?

Jan 1, 2011

By Martin Banda, Gift C. Chisakuta, Moses Chabinga

KCM made a major modification to the Nchanga Tailings Leach Plant (TLP) changing the circuit from feeding post leach thickeners in parallel with leach discharge for solid ?liquid separation to a Counter Current Decantation (CCD) configuration utilising most of the existing equipment. The new circuit is aimed at improving copper recovery from approximately 70% to 79% through enhanced wash efficiency. The re-introduction of CCD circuit at elevated throughput of 46 000-tpd design was made possible due to the EIMCO E-Duc technology design which is an auto-dilution system that enhances solids settling rate. Commissioning (manual operation) which accommodated on-going operational requirements was phased and completed in January 2004. The circuit stabilised in subsequent months and in March alone an all time record copper recovery of 81.8% was achieved which contributed an extra 779 tonnes copper above the plant?s projected production plans. 100% of the project cost was paid back by end of April 2004 This paper discusses the work involved and the challenges faced during the re-commission

Jan 1, 2005

Jan 1, 1967

By E. H. Myrhaug, K. Aasly, T. Malvik

Quartz is one of the main raw materials for the carbothermic production of ferrosilicon and silicon metal. The ideal process is written: SiO2 + 2C = Si + 2CO The real process is much more complicated, depending on the quality of the raw materials. Several research projects have been carried out on quartz for the (Fe)Si process during the last 50-60 years. One of the important properties that have been discussed in this review is the volume expansion that takes place between 850 °C to 1000 ºC and explosive disintegration for some quartz types. No final and definite conclusions have been made but several reasons have been mentioned: The influence of the phase transformation to tridymite, which takes place within the same temperature interval, has been discussed in several papers. Alkali impurities have been mentioned as a critical factor for this transformation to take place. Other researchers have mentioned mica impurities as a critical factor for the behavior of the quartz at these temperatures. Studies of fluid inclusions in quartz was reported in some papers focusing on the volume expansion of these during heating as a source of explosive disintegration, especially along planes of healed micro fractures that often contain vast numbers of such inclusions. Several methods for investigations of the important properties of quartz have been presented and these provide a good basis for the further research on quartz raw materials.

Jan 1, 2007

By T. Yalcin

"This paper describes the development of a mathematical model for determining the liberation of an ore at various grinding sizes, based on the combined results of microscopic counting, grinding tests, and chemical analysis.The method is illustrated with an application to the magnetite ore of Sherman Mine in Temagomi, Ontario. For this ore, a degree of liberation of 98.7% was determined at a grinding size of 90% passing 44 microns, which closely corresponds to the final grinding size employed at the Sherman Mine Concentrator.Introduction Liberation characteristic of ores have direct and significant bearing on overall economics of concentration processes.Target grades and recoveries can be achieved only it minerals are adequately liberated prior to separation. Degree of liberation depends on the extent of size reduction. However, due to the high costs associated with size reduction processes, it is important to keep size reductions within limits of satisfactory liberation. Prevention of excessive size reduction is also necessary because of inefficient mineral separations in very fine sizes. Hence, a study of reduction size — liberation relationship is essential for optimum profit from milling operations.A number of procedures have been developed for liberation studies (1-12), but there is lack of method for universal adoption.A new approach is presented in this paper that might provide a realistic estimate of liberation and give a practical guidance as to the degree of size reduction required for satisfactory liberation."

Jan 1, 1985

By Zeljka Pokrajcic

Crushing and grinding, or comminution, circuits are the most energy intensive process of a mineral processing plant. Comminution involves the physical size reduction of an orebody to a particle size sufficient for recovery of the mineral values. However, the comminution process remains inherently inefficient. The inefficiency is a result of the operating nature of comminution devices such as grinding mills, where transfer of energy between grinding media and particles in unconstrained and completely random. New comminution circuit design strategies are presented in this paper. The aim of the new strategies is to improve the overall efficiency of the comminution process and reduce the total energy consumption of a comminution circuit. The energy efficient strategies include the: ? rejection of coarse size liberated gangue from the comminution circuit and further downstream size reduction ? use of more efficient grinding and crushing equipment ? the selection of coarser particle product sizes to alleviate the increased energy intensity required to achieve finer product sizes Singularly and when combined, these energy efficient strategies can significantly decrease the overall energy consumption of a comminution circuit. This paper also explores the financial impact of certain energy efficient strategies using an analysis tool called EcoNomics?. It shows that substantial financial gains can be made by including more efficient technologies and methods in comminution circuit design.

Jan 1, 2010

By R. L. Zick, D. C. Finn

Introduction The high-density sludge process was originally developed by Bethlehem Steel Corp. for use on acid mine drainage (AMD) and diluted waste pickle liquor discharges requiring continuous chemical-treatment. This work began in the early 1970s and was first put into practical use around 1973. To date, there are approximately 15 operating systems that have been installed to treat mine drainage in the United States. In addition, there are another 10 systems installed outside of the United States. The dense-sludge process is an innovative and improved method for treating acidic metal-bearing streams in a manner that minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge-recycle process that forms particles with a low affinity for water. These particles are unlike conventional metal hydroxide solids that contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations that combine with calcium ions in lime-based treatment systems to form gypsum crystals. Compared to the form generated in conventional lime treatment systems, the physical form of the gypsum is radically altered when the dense-sludge process is utilized. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. The dense-sludge particles settle faster, dewater more readily, are more easily pumped and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered. In general, the conventional and dense-sludge treatment processes are very similar. The changes required to implement the dense-sludge process are minor, and, typically, much of the existing equipment can be utilized. The net results of the process are: reduced operational costs associated with sludge generation, improved process control (particularly pH control), reduced gypsum deposition (i.e., less scaling) on system components and reduced sludge generation resulting in less return water for treatment. Despite the relative simplicity of the process, the application of the technology requires careful discrimination, and the "experience factor" for implementation is an important consideration that should not be over looked.

Jan 1, 2000

By George Watson, Gu Quanzhong, S. Gerard Sawyer

Bulkheads, also known as hydraulic seals, are used to seal abandoned workings and protect adjacent active mines from explosion and control unwanted inflows of water from poorly sealed shafts, water-bearing strata, and abandoned mine areas or gobs (1). At coal seam outcrops, bulkheads have typically been used to prevent access and to control acid mine drainage. Bulkheads have also been installed at outcrop openings located within the footprint of an embankment dam, or within the reservoir of an impoundment, to prevent stored water or slurry waste from flowing into active or inactive underground mine workings (2). Components of MICON Bulkhead Seal MICON bulkhead seals in mining applications refer to seals designed to impound liquids or slurry. The MICON bulkhead seal is comprised of two concrete block walls set in the front and back and a polyurethane/aggregate core (Figure 1). The two walls are usually dry-stacked, surface-bonded walls constructed with solid load-bearing concrete blocks (ASTM C90) or concrete building brick (ASTM C55). The surface bonding material used in the wall construction must be MSHA-approved. The type of stone, if any, used to fill the space between the walls is not essential. However, MICON generally uses No. 57 limestone in 50 lb. bags, specified to moisture control, shrink-wrapped and palletized. The polyurethane foam used in the construction of the bulkhead seal is engineering specified and formulated by density based on the optimization of cost, seal core thickness, required adhesive strength, the use of stone filler and other required physical properties.

Jan 1, 2005

By John H. Raymer

Groundwater inflow into hard rock tunnels is strongly affected by recharge and drawdown of the water table. Previous analytical and empirical methods for estimating inflow have generally not accounted for these factors in an accurate or systematic way, resulting is wrong conclusions about inflow and the effects of the tunnel on the surrounding environment. This paper discusses these issues and provides some simple analytical equations to estimate inflow and water table drawdown around the tunnel. Examples from tunnels in the Atlanta area are provided.

Jan 1, 2005

By Roy S. Nutter

The automation of coal mining must occur in a manner that is economically beneficial to the industry and that enhances the safety of the underground and surface workplaces. The work at WVU over the last five years in applying expert systems and neural network controlled autonomous robotics provides the mining industry with tools that when properly applied should clearly lead to mine-wide management and operational improvements and should also contribute to a higher awareness of safety issues by all work crews. This work includes the development of MMSS (Mine Management Support System) and the detailed development of autonomous robotics utilizing neural networks for mining systems.

Jan 1, 1993

By Louis Schaffer

The objectives of the research were to determine whether a model health and safety program could be defined in terms which would enable its application to mines of all types, and, if such a model program could be defined, to determine through evaluations in two mining companies whether it would achieve measurable improvements. Volume 1 describes the model, how it was applied in the field and how it was evaluated. This, Volume 2, describes the literature and field research that preceded the model definition.

Jan 1, 1983

By W. C. Blanchard

Time Domain Reflectometry (TDR) is a remote sensing technique using active backscatter. This technique is applicable to the testing for faults and multiple partial faults on cable. The battery operated hardware developed on this con¬tract has tailored this technique for testing of mining equipment trailing electrical cables. The processing of-t-he back-scatter is accomplished using a microprocessor. The visual output from the hardware to the operator is; the type, magnitude and distance to the cable fault in a numerical format. This greatly simplifys the use of this techniques for the operator.

Jan 1, 1980

By Lewis M. McNay

The strength characteristics of hydraulic sandfill modified by varying quantities of type III portland cement and two flocculants were investigated by the Bureau of Mines. Three different sand-cement ratios were examined using different percentages of flocculant. Two other experimental variables were curing time and weight-percent solids for hydraulic mixture. Results of unconfined compression tests with strain are discussed. Maximum strength was achieved with 0.5 weight-percent of ferric sulfate per ton of solids when the slurry mixture was 75 weight-percent solids. The bearing capacity of hydraulic sandfill is reduced by increasing the water content and decreasing the amount of cement mixed with sandfill.

Jan 1, 1976

By Russell A. Schreiner

In conjunction with the Geological Survey, the Bureau of Mines conducted a mineral investigation in 1981 and 1982 of the Santa Rosa Mountains Wilderness Study Area (WSA), Riverside County, California. The Bureau of Mines is responsible for the mineral survey of mines, prospects, and mineralized areas in and near the WSA. A literature search was completed to obtain information concerning mineral occurrences and mining activity that relate to the WSA. A field investigation inside, and up to 1 mi outside, the boundary of the WSA, disclosed one prospect. This prospect was surveyed by compass and tape, and five samples were taken to determine the representative mineral content. No attempt was made to expose concealed mineralization or to re-open caved workings. All five samples were analyzed by fire assay for gold and silver and by colorimetric methods for tungsten. Two of the samples were analyzed by semi quantitative spectrographic methods to determine if any unsuspected elements were present. All analyses are furnished in this report except for the semi-quantitative spectrograhic analyses. Complete sample analyses are available for public inspection at the Bureau of Mines, Intermountain Field Operations Center, Building 20, Denver Federal Center, Denver, CO 80225.

Jan 1, 1983

By Tripathy A. K, Satapathy B. K, Nayak B, Mohanty J. N, Dey D. N

The paper deals with the metallographic tudy of heat treated chromite and chromite-coke composite briquettes. The briquettes, prepared from chromite concentrate of Orissa Mines using molasses-lime, dextrinelime and tamarind seed as binders, were subjected to different temperatures and examined metallographically. The change of phase with temperature was analysed by X-ray diffraction.

Jan 1, 1987

By Masami Hayashi

The Bureau of Mines conducted laboratory studies to investigate methods for desilicating sodium aluminate solution derived from leaching a limestone-anorthosite sinter with 10-pct Na2C03 solution. Desilication tests were made at atmospheric pressure to determine the effects of time and additions of lime and desilication residues. A two-stage, countercurrent desilication procedure was developed to reduce the Si02 content sufficiently to meet specifications for cell-grade A1203. Both stages were conducted at boiling temperatures at atmospheric pressure. Reagent lime was charged as desilication seed to the partially desilicated solution in the second stage, and a product (desilication residue) precipitated by the lime addition was charged to the freshly leached solution in the first stage. Average A1203 loss in the desilication circuit was 5.8 pct, and the product solution contained less than 0.04 g/l Si02. Complete precipitation of A1203 by carbonation resulted in a hydrate containing less than 0.01 pct Si02. Calcination of this hydrate would produce A1203 meeting the 0.015 pct Si02 specification for cell-grade material.

Jan 1, 1982