Search Documents

Jan 1, 1963

Jan 1, 1971

By V. N. Krivobor

The study and use of low-carbon manganese steels have been curiously neglected in the general history of developments in alloy steels. Hadfield1 made an extensive study of manganese-iron-carbon alloys about 1886, which culminated in the wide application and use of Hadfield austenitic manganese steel. His alloys were nearly all high in carbon, as compared with the steels discussed in this paper, and he found a marked tendency toward brittleness in the alloys of medium and low manganese content, that is, below 7 per cent. manganese. As a result, there has been a widespread prejudice against the use of manganese steels containing between 1.0 to 3.5 per cent. manganese with comparatively low carbon. Steels of this composition have never been studied adequately in comparison with other alloy steels, and have had litttle use in practice. In a very recent paper by Sir Robert Hadfield2 the following statement appears: 6L... manganese-iron alloys with little or no carbon do not seem to offer any practical employment; they only become valuable in the presence of quite high percentages of carbon, 0.90 to 1.50 percent." The results of the present investigation are so contrary to the findings of Hadfield that the writers feel fully justified in presenting the preliminary report incorporated in this paper. Previous Investigations As early as 1886 the Terre Noire CO.3 in France produced alloys containing up to 2.5 per cent. of manganese, using ordinary low-grade

Jan 1, 1927

By AIME AIME

THE papers presented at the geophysics session" on Feb. 17 were concerned largely with three aspects of the science. The first ones dealt with the transmission of elastic waves through the earth, then electrical methods came in for their share of attention and finally, the question of the teaching of geo- physics came up for the first time at these meetings. Also, for the first time, there was a symposium of mining men on the practical value of the new science. The paper (T. P. 267) entitled "Seismic Propagation Paths" was presented by Donald C. Barton in the absence of the authors. It dealt with an investigation of the speed of propagation of seismic waves. The latter travel in a straight line when proceeding at a constant velocity, but if the velocity increases at increasing depths, the line of travel becomes a curve. Under the assumption of the authors this curve is found to be the arc of a circle, and their paper gives calculations for reflected and refracted wave paths under these circumstances.

Jan 1, 1930

By B. C. Blake

IN general, billet-type or long slender ingots are used when it is desired to produce directly from the ingot in one conversion a product of medium or small cross-sectional area. They are designed to eliminate the blooming and billet-mill stages of the usual procedure. As used at Connors, they constitute a means of keeping a continuous rolling mill busy in the production of high-quality small rods, small angles, hoop stock, baling ties and concrete reinforcing rods without the need for a blooming or billet mill. They represent sound steel with the best surface that is commercially practical to use in the rolling of small continuous mill products.

Jan 1, 1947

By H. S. Gibson

A PROCESS that has come to be known locally as "multistage stabiliza-tion" has been developed in the Haft Kel field of the Anglo-Iranian Oil Co. in southwest Iran, for the recovery of casinghead gasoline. It con-sists in releasing the dissolved gases from the crude by stages, a practice common in many fields, but which, so far as is known, has nowhere been carried to the extent to which it is employed in Iran. It has been in use there for nearly nine years, during which time some 200 million barrels of crude have been handled by the process. This process of gasoline retention consists in preventing the greater part of the casinghead gasoline hydrocarbons (the butanes and pentanes) from ever leaving the crude, instead of allowing them to be vaporized and then recovered from the lighter gases by the usual compression or absorption processes. Its efficiency is fully equal to that obtained by the absorption process; its disadvantage is that it increases the quantities of ethane and propane in the crude sent to the refinery, but with the growing demand for propane this drawback is vanishing. When casinghead gasoline is recovered as a separate liquid in the Iranian fields, it is blended with the crude, as the only outlet is through the refinery, and the crude-oil pipe line offers the cheapest means of transportation. It is under these conditions that the retention of the butanes and pentanes in the crude by multistage stabilization is a most attractive process, possessing as it does the following advantages: (1) extreme simplicity, (2) low first cost, (3) easy installation, (4) practically 100 per cent operating-time efficiency, (5) no operators required, (6) no water or other services required, (7) negligible maintenance, (8) once established, very little routine testing is necessary. The one essential for reasonably efficient multistage stabilization is that the flowing pressures of the wells should be relatively high; i.e., they should not be less than about one-third the saturation pressure of the crude in the reservoir. This is a very general statement, of course, and much depends on the type of crude and its temperature.

Jan 1, 1939

By P. Sanchez-Mejorada

GEOLOGISTS who are acquainted with the mines of northeastern Mexico realize that the most important lead-silver replacement deposits of the province are confined to a single formation. But since the formation is several hundred meters thick, the author has determined the relative position of the lead mantos in the belief that this information will prove useful in the search for new mines. This article describes the stratigraphic location of lead-silver replacement deposits known in several mines situated in a region comprising part of the states of Coahuila and Nuevo Leon. The area studied extends for 200 km* (125 miles) from east to west and 70 km (45 miles) north to south. Metallogenic Province: The most important metallic deposits of the region have the following common characteristics: 1) The orebodies occur as manto replacements of calcareous sediments. 2) The horizons that have contributed large tonnages of ore are in similar positions in the corresponding stratigraphic columns (as it will be shown later on). 3) Lead is the most important metal in the ores. Silver is commonly present in small amounts. Occurrence of zinc is dependent on the degree of oxidation of the primary sulfides. 4) A large proportion of the total production has been in the form of oxidized ores. 5) The deposits are located on anticlines. Rocks of Cretaceous age crop out over large areas of the states of Nuevo Leon and Coahuila. forming part of a belt that extends to the south along the eastern Sierra Madre. The sediments are cut by a small number of intrusive stocks ranging in characteristics from rhyolite to diorite. The most prominent structural feature of the region is a series of folds trending northwest-southeast. Faulting is not conspicuous in the region, although a major fault zone is found farther East.' The physiography closely reflects structural features, with mountains formed by anticlines and valleys conforming with intermediate synclines. Narrow valleys have also been developed along the axes of many anticlines, where solution of limy sedi- ments and erosion have proceeded along axial tension fractures. Stratigraphy: Rocks of the Upper Cretaceous are exposed in only a small percentage of the total area. Generally they have been eroded away from the mountains and are covered by recent talus and alluvium in the valleys. Humphrey' has published an excellent paper describing the Cretaceous formations of the Sierra de los Muertos, a short distance west of Monterrey. A brief summary of these formations is given below to convey an overall picture of the stratigraphic sequence that prevails just south of the area under consideration. Upper Cretaceous Indidura: Essentially thin shaly sediments. Cuesta del Cura: Limestone in thin wavy beds

Jan 1, 1959

IT is not necessary to enter into a long discussion of ordinary bells, because every master carpenter or blacksmith knows how to make those levers with a crossbar that are called storks. This is nothing other than a board that has a thick and heavy head and looks more like a dolphin than a bird. This has a long tail in the form of a handle so that it makes a more powerful lever. As can be seen in every bell tower and other place where there are bells, it has, crosswise above the point where the cannon of the bell is fitted and fastened in, an iron bar which is arched and which has its two ends turned horizontally. These are made round so that they may turn easily when they are held by two steel rings or in two metal grooves or on glass pillows. In this, the more the transverse rod is arched,

Jan 1, 1942

By Clinton M. Young

(Pittsburg Meeting, March, 1910.) I. INTRODUCTION. THE experiments herein. described were carried on in 1908-9 . by the State Geological Survey of Kansas. Some months before taking up work on black powder the Survey had resumed work on an interrupted investigation of explosions in coal-mines, a subject which is engaging the attention. of numerous investigators. An unusual number of serious disasters has directed to. the subject a study which discloses the disquieting fact that, in the. United States, the ratio of lives lost per ton of coal mined has been on the increase. Methods of coal-mining have changed to some extent with the great increase of output, attained in, comparatively recent years. These changes involve the working of very extensive mines, with increased difficulty of ventilation, increased accumulation of coal-dust, and. a very great increase in the amount of explosive used.. . This last point assumes truly startling proportions when it is carefully observed. In the fields of the Middle. West it is not now uncommon for a miner to use six ,kegs (150 lb.) of black powder in a "pay" of two weeks, while within the memory. of men still active, one keg (25 .lb.) would last two men for a " pay." So. great has . the use of explosives become in some fields that the skilled coal-miner is hard to find, and the coal is not mined, but blasted. A preliminary study of the subject. of explosions in coal-mines has. led to the belief . that the use of, large -quantities of explosives, in some cases by slightly-trained men, had not been * Associate Professor- of Mining Engineering, University of Kansas, Lawrence, Ran.

Aug 1, 1910

By A. L. Holley

THE application of scientific methods to the investigation of natural laws and to the conduct of the useful arts which are founded upon them, is year by year mitigating the asperity and enlarging the outcome of human endeavor. More notably, perhaps, are these the facts in that system of productive and constructive arts of, which engineering is the general name. In metallurgical engineering especially, within the period of our own recollection, how rapid has been the rate and how wide the scope of progress: the scientific discovery and mining of metalliferous veins; the economical separation and reduction of ores of every grade; the production and regulation of high temperatures; the varied improvements in the manufacture of iron, in saved heat and work, in uniformity and range of products ; and, most important of all, the creation and the utilization, to be counted by the million tons a year, of the cheap constructive steels. Wonderful as this range and degree of development may appear to the public eye, the close and thoughtful observer must, nevertheless, conclude that neither the profession nor the craft of engineering may congratulate themselves too complaisantly, but that they should rather acknowledge to each other the embarrassing incompleteness of the union between engineering science and art. There is a small school of philosophers whom we may designate as original investigators, men who come close to nature, who search into first principles, and who follow that scientific and therefore fruitful method by which the relations of matter and force are discovered, classified, and brought within the reach of practice. These wonderful - men do not indeed create the laws of nature, as they sometimes almost seem to, but they go up into the trembling mountain and the thick darkness and bring down the tables upon which they are written. * President's Opening Address. The discussion following this paper, and also the Joint Discussion of the Institute and the American Society of Civil Engineers, on the subject of Technical Education., are published in a separate volume.

Jan 1, 1876

By H. S. Gipson

A process that has come to be known locally as "multistage stabilization" has been developed in the Haft Kel field of the Anglo-Iranian Oil Co. in southwest Iran, for the recovery of casinghead gasoline. It consists in releasing the dissolved gases from the crude by stages, a practice common in many fields, but which, so far as is known, has nowhere been carried to the extent to which it is employed in Iran. It has been in use there for nearly nine years, during which time some 200 million barrels of crude have been handled by the process. This process of gasoline retention consists in preventing the greater part of the casinghead gasoline hydrocarbons (the butanes and pentanes) from ever leaving the crude, instead of allowing them to be vaporized and then recovered from the lighter gases by the usual compression or absorption processes. Its efficiency is fully equal to that obtained by the absorption process; its disadvantage is that it increases the quantities of ethane and propane in the crude sent to the refinery, but with the growing demand for propane this drawback is vanishing. When casinghead gasoline is recovered as a separate liquid in the Iranian fields, it is blended with the crude, as the only outlet is through the refinery, and the crude-oil pipe line offers the cheapest means of transportation. It is under these conditions that the retention of the butanes and pentanes in the crude by multistage stabilization is a most attractive process, possessing as it does the following advantages: (1) extreme simplicity, (2) low first cost, (3) easy installation! (4) practically 100 per cent operating-time efficiency, (5) no operators required, (6) no water or other services required, (7) negligible maintenance, (8) once established, very little routine testing is necessary. The one essential for reasonably efficient multistage stabilization is that the flowing pressures of the wells should be relatively high; i.e., they should not be less than about one-third the saturation pressure of the crude in the reservoir. This is a very general statement, of course, and much depends on the type of crude and its temperature.

Jan 1, 1940

By H. S. Gipson

A process that has come to be known locally as "multistage stabilization" has been developed in the Haft Kel field of the Anglo-Iranian Oil Co. in southwest Iran, for the recovery of casinghead gasoline. It consists in releasing the dissolved gases from the crude by stages, a practice common in many fields, but which, so far as is known, has nowhere been carried to the extent to which it is employed in Iran. It has been in use there for nearly nine years, during which time some 200 million barrels of crude have been handled by the process. This process of gasoline retention consists in preventing the greater part of the casinghead gasoline hydrocarbons (the butanes and pentanes) from ever leaving the crude, instead of allowing them to be vaporized and then recovered from the lighter gases by the usual compression or absorption processes. Its efficiency is fully equal to that obtained by the absorption process; its disadvantage is that it increases the quantities of ethane and propane in the crude sent to the refinery, but with the growing demand for propane this drawback is vanishing. When casinghead gasoline is recovered as a separate liquid in the Iranian fields, it is blended with the crude, as the only outlet is through the refinery, and the crude-oil pipe line offers the cheapest means of transportation. It is under these conditions that the retention of the butanes and pentanes in the crude by multistage stabilization is a most attractive process, possessing as it does the following advantages: (1) extreme simplicity, (2) low first cost, (3) easy installation! (4) practically 100 per cent operating-time efficiency, (5) no operators required, (6) no water or other services required, (7) negligible maintenance, (8) once established, very little routine testing is necessary. The one essential for reasonably efficient multistage stabilization is that the flowing pressures of the wells should be relatively high; i.e., they should not be less than about one-third the saturation pressure of the crude in the reservoir. This is a very general statement, of course, and much depends on the type of crude and its temperature.

Jan 1, 1940

By Albert F. J. Bordeaux

INTRODUCTION. THE following general survey of the character and present condition of the silver-mines of Mexico, though not offered as a detailed treatise, has been prepared with care, is believed to he generally up-to-date, and is offered as a summary which may be found useful by mining engineers. Mexico has ranked for several centuries first among the silver-producing countries. It is now second as copper-producer, and seventh as gold-producer, with a fast-increasing output every year. The total amount of capital invested in its mining- and smelting-works is more than $250,000,000, while the yearly metallic production is $160,000,000. There are more than 20,000 recorded mining properties. The silver-mines of Mexico represent deposits of three principal classes: (1) veins and stock-works in eruptive rocks; (2) fissure-veins crossing the crystalline schists, granite, diorite, etc. ; and (3) veins and replacement-deposits in limestone. The true fissure-veins in some districts contain (in value) more gold than silver. In other deposits, the silver is decreasing in depth, leaving galena and zinc-blende as the principal ores.

Jan 9, 1908

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ANDREWS, CLARENCE W., 2d Lieutenant, 12th Batt. Infantry Replacement Regiment. ANDREWS, JOSEPH C., Ordnance Dept., U. S. A. ARLUCK, A. A., Headquarters, 1st Corps of Artillery, A. P. O.. No. 759, A. E. F.

Jan 9, 1918

By R. G. Bentsen, D. A. T. Donohue

The cyclic steam injection process has become the most widely applied and most successful thermal recovery technique in use today.1-4 Normally, steam stimulation is repeated several times during the life of a project. The problem is to select the optimum number and size of steam treatments so that the profits realized over the entire life of the project are maximum. Obviously, operating costs rise directly with the frequency and amount of steam injection. Operating efficiency, on the other hand, can be adversely affected if the amount and frequency of stimulation are insufficient. Thus arises a multistage decision problem; that is, a decision must be made at each sub-period (day, for example), as to whether steam should be injected, and, if so, how much. It is desirable that these decisions be made in such a way as to secure maximum net profit before taxes. This can be achieved by dynamic programming. To use dynamic programming, we must be able to predict not only the production rate-time curve resulting from a given stimulation, but also how changes in stimulation policy will affect this curve. In this study, the effect of steam injection on well performance is estimated on the basis of a simple model that takes into account both steady-state and transient flow. Oil production rate is calculated for both types of flow, and the larger of the two values is used. This allows the calculation to change to radial steady-state flow at such time as this mechanism becomes more effective than the transient mechanism. We propose to show how dynamic programming can be used to optimize the steam soak process with respect to net profit. For this, a mathematical representation of the steam soak technique is necessary. A further objective, therefore, is the formulation of a mathematical model capable of realistically simulating the physical process. Oil Production Response Model The advantage of using a mathematical model is its generality and ease of manipulation. However, the model must be an accurate representation of the physical process, for a solution derived from a model can be no better than the model itself. The question now arises as to how well the model should be expected to simulate reality. In general, the simplest model should be tried first, for additional accuracy is apt to require additional cost and time. Also, the search for a high degree of accuracy may yield only greater complexity and difficulty without yielding significantly better results. With this in mind, we kept our model as simple as possible, yet generally representative of the actual physical process. The number of state variables is limited to three, and stochastic variations in the parameters are ignored. As a consequence, use of this model should be restricted to cases in which the underlying assumptions are not severely violated. In

Jan 1, 1970

By A. STEPHENSON

EXPERIMENTAL work conducted at the Petroleum Engineering Laboratory of the University of California by L. C. Uren, J. Domercq, Jr., and J. Mejia has shown that small diameter wells offer tremendous resistance to the flow of fluids in their immediate vicinity. This resistance is due in part to the constriction of the area through which the fluids must pass as they approach the wall of the well, but is also accentuated by the increased volume which results from gas expansion. The latter in turn is a function of the deduction in pressure, the fundamental cause of fluid movement. If the diameter of the bore is enlarged several diameters, the capacity of the well, or the volume of fluid passing per unit drop in pressure per unit of time, is greatly increased without necessitating such high fluid velocities. The fundamental features which should be taken into consideration in the design of casing joints were stressed by J. B. Graham and E. E. Smith. These involved such points as correct thread design, high efficiency, and small diameter, together with the insurance that leakage will absolutely be prevented. The practical features of such design were ably discussed by engineers from leading steel manufacturers.

Jan 1, 1935

By S. E. Bretherton

This title introduces the subject I wish to describe to my fellow members, very few of whom, I 'hope, have ever had as much trouble with the smelting of ore containing much zinc, either in the lead blast furnace or the matting furnace, as circumstances have forced upon me: First, for several years in Leadville, Colo., after the sulphide ores containing zinc had been developed with greater depth and were sold to the intereats with which I was connected for smelt-ing in the blast furnace for the recovery of the lead, silver, and gold; then, in New Mexico and Arizona, where the principal source of ore supply for our custom smelter was from miners who sent most of their product in the form of concentrates, which we briquetted and smelted in the blast furnace, producing a matte containing copper, silver, and gold, for which we were paid; together with some zinc and lead, which was penalized if in excess of a maximum base set by the refinery to which we sold our copper matte; last, but not least, my experience in Shasta county, Gal., where for the sake of recovering $13 per ton value in copper, silver, and gold, I have smelted ore containing as high as 40 per cent. zinc (the last 18,951 tons smelted averaged 15 3/10 per cent. zinc) which we not only lost, but which it cost us money to lose. After such an experience, and knowing that, instead of being worth only $13 per ton, such 15 per cent. zinc ore should be worth about $30, including zinc at the present market value, the question of recovering the zinc in a profitable manner from such ore became very interesting to me. During several years' time I sent samples, of from 5 to 1,200 lb. each, to be tested by the different best-known zinc-recovery plants, and experimented with several processes proposed by others for the treatment of such ore, with but little encouragement, until I

Jan 1, 1914

By Cornelius F. Kelley

EVERY man connected with the mining industry should take a significant pride in the fact that he belongs to an industry and to a profession that, from the beginning, has been constructive. The miner digs his ore and he gives the metal to art, to industry, and to commerce. The nature of our business is destructive only in that we deal with a wasting asset. That should be a source of great pride to those who belong to the profession. But unfortunately, the product of our mines, our smelters, and our re- fineries does not always go to constructive purposes. There are times when, in the administration of the affairs of men, our product chiefly goes to purposes which are destructive. When we look upon the panorama of horror that is being enacted throughout the world today, we wonder whether any effort toward the development of civilization and culture and education and well-being has been worthwhile. We are appalled to see the things that have been developed, through the application of science, toward progress and efficiency, now used for the catastrophic destruction of those things which are the most valuable that man has built. We must find hope that this is but an episodic thing; that it must, in the infinite wisdom of the Almighty, usher in a period of peace and progress, of civilization and development that will make man's existence upon earth worthwhile.

Jan 1, 1941

By J. C. Bradley

THE relation of annealing temperature to conductivity of copper wire has been determined. Conductivity hard was 98.26 per cent. After a 10-min. heating at 200°C. it was 98.69. By annealing 10 min. at 300° C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500° C. anneal; thereafter it decreased to 100.53 after a 950° C. anneal. If copper is gassed the decrease is much more than this. Materials and Methods The work was done on high grade electrolytic copper, 99.942 per cent. copper plus silver, silver 0.0008 per cent. It was hot-rolled to >/4 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100° C. heating a coil was put into water, the water brought to boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire 'were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched.

Jan 1, 1927

By T. A. Rickard

A knowledge of the principles of punctuation is essential to effective and intelligible writing, for the ease and pleasure of the reader, and even his understanding, may depend upon the choice and the placing of punctuation marks. To 'punctuate' is to mark with stops or points; the word comes from the medieval Latin punctuare (punctuatus), which in turn is derived from the Latin punctum, a point. The purpose of punctuation is to show the manner in which the writing is to be understood; to indicate the relations between parts of a sentence and between successive sentences. To some extent "it does for the eye what vocal stress does for the ear", but especially it marks logical relations. Some punctuation marks, such as those indicating admiration, exclamation, and interrogation, are rhetorical as well as grammatical, but most of the common ones are logical, or grammatical. My discussion will be confined to grammatical punctuation in ordinary writing. .'The problem of punctuation in text matter", as George Summey * says, "is to employ words, points, and paragraph breaks in such a way as to achieve at the same time clearness; proper distribution of emphasis, and the desired kind of movement." The criticism of the punctuation of a sentence or of a group of sentences is not final until the context, within the paragraph, is read. A paragraph is a sentence or a group of sentences forming an independent unit of the composition; it represents a unit of thought. A multiplicity of paragraphs produces a choppy effect; 'on the other hand, paragraphs of. excessive length are tiresome, because the belaboring of one unit of thought wearies the reader. The aim should be to

Jan 1, 1931