Search Documents

By Cyril Stanley Smith

THE art of metallography is mature and the forms in which various micro-constituents appear are well known. Investigations almost without end have disclosed the importance of the exact manner of distribution of phases on the physical properties and usefulness of an alloy. Surprisingly, however, relatively little attention has been paid to the forces that are responsible for the particular and varied spatial arrangements of grains and phases that are observed. Like the anatomist, the metallurgist has been more concerned with form and function than with origins. In this paper it is proposed to develop the simple concept that many microstructures result from an attempted approach to equilibrium between phase and grain interfaces whose surface tensions geometrically balance each other at the points and along the lines where they meet. From this follows a number of principles which may prove to be of interest to the metallographer and of practical use in explaining failures and in designing alloys for particular service. In general, the discussion will be limited to structures obtained after full annealing. The simple principles do not apply to structures resulting from Widmanstatten mechanisms in precipitation, or to other structures not in local equilibrium and in which lattice coherency is a determining factor. INTERFACIAL TENSION Much has been written by physical chemists about the free energy of surfaces, which manifests itself as a measurable surface tension. Two- and three-phase interfaces in fluids seek a condition of minimum energy and approach a geometrical configuration in which the various forces are in vectorial balance.* Measurement of the angles established between the interfaces when in equilibrium provides a quantitative value for the relative value of the surface forces involved. The case of two fluids meeting at the surface of a solid (of great importance in connection with the flotation of minerals) has often been studied, but there have been few investigations of the equally definite interface between two or more crystals of a single solid phase, or the more complex cases where crystal grains of more than one phase are involved. The principles are best illustrated by considering first the case of two and three immiscible liquids. If, as in Fig I, a liquid, 2, is dropped into a less dense liquid, I, it will form a sphere-if gravity and viscosity can be ignored-for in this shape the interface has the smallest possible area. If these two phases should together encounter a third phase in which they are both immiscible, the geometry will change to become that which gives the lowest total energy for all three interfaces. Thus, if the spherical drop of liquid, falling through r, eventually reaches the interface between liquids 3 and I (we are assuming that the density of 3 is greater than 2, and 2 than I), it will assume the shape of a lens, the angle

Jan 1, 1948

By Robert D. Longyear

IN MOST diamond core drilling the primary objective is the recovery of samples to be used for chemical analysis, physical tests, or visual inspection. Unless these samples are reliable and the information systematically recorded, the time and money spent in securing them are largely wasted. A properly taken diamond-drill sample is similar to a properly moiled channel sample but more accurate. No channel sample can be moiled in as even a groove as the smooth cylinder of material normally removed in diamond drilling. More important still, sampling by the diamond drill practically eliminates that personal equation which Jora1emon4 reference numbers apply to publications listed in the bibliography at the end of this article) has aptly termed "the almost magnetic attraction of the most conscientious hand toward rich pieces of ore."

Jan 1, 1937

Aamot, Olav Crone, Chem. Engr., Norsk Elektrokemisk, Kongensgt. 18, Olso. Norway. '29 Abadilla.-Quirico A., Dir., Bureau of Mines Manila, P. I. '38 Abbott, Clarence E., V.P., Charge of Raw Materials, Tennessee Coal, Iron & R.R. Co., 1212 Brown-Marx Bldg., Birmingham, Ala. '04 Abel, Raymond L., Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. '29 Abel. Walter D., Cons. Engr 1839 Holmby Ave., W. Los Angeles. Calif. '32 Abele, Louis T R. F. D. 5. Susquehanna Trail, N., York. Pa. '31 Abell, Leo M., Ore Dressing Investigator, School of Mines Adelaide, S. Australia. '31 Abenius. Hakan V., Mine Supt., Bolidens Gruvaktiebolag Boliden, Sweden. '37 Aborn, Robert H., Asst Met., Research Lab., U. S. Steel Corp. Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., East India United Service-Club, 16 St. James' Sq., London, S. W. 1, England. '28 Abrams. Charles Jackson 1624 17th St., Denver, Colo. '36 Abstein, Henry T., Engr. & Mgr., Profile-Tamarack Mines Co Yellow Pine, Idaho. '27

Jan 1, 1938

By F. G. Cottrell

AS previously announced, Van. H. Manning has resigned as director of the Bureau of Mines, effective June 1, to become director of research with the newly organized American Petroleum Institute. Doctor Manning has been connected with the Department of the Interior for 34 years, having been civil engineer with the Geological Survey, from 1885 to 1910, previous to his connection with the Bureau of Mines which was organized in the latter year. Doctor Manning was appointed to an administrative position in the new Bureau under Joseph A. Holmes, its first director, and on Jan. 1, 1911, was made assistant director. On Jan. 1, 1914, when Doctor Holmes had to relinquish active

Jan 1, 1920

By H. E. Criner, M. G. Driessen

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By M. G. Driessen, H. E. Criner

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By A. Poll, J. E. Stantan, L. J. Jolley

THE basic problem in the generation of water gas from carbonaceous fuels and steam is the supply of the heat of reaction, and in general the source of this heat is the combustion of a further quantity of carbon with oxygen. Existing and proposed processes for complete gasification differ in the methods employed for transferring this heat to the fuel, and involve one or other of the following alternatives: 1. Use of a steam-oxygen mixture as the gasifying medium, so that the combustion and gasification reactions are combined. 2. Alternate passage of air and steam through a fixed bed, as in conventional water-gas production. 3. Cyclic passage of fluidized fuel through combustion and gasification zones. 4. Intense preheating of steam and of a portion of the gas made, and recirculation of this mixture through the fuel bed. 5. Supply of heat to the fuel bed through an externally heated wall. Except for the conventional water-gas process using large coke or low- volatile coal, only processes in the first group, operating with steam and oxygen, have proved practicable with fuels other than brown coals and lignites. A possible exception, which has not so far reached a commercial scale, is the moving-burden process developed by Imperial Chemical Indus- tries, Ltd. The cost of industrial oxygen is so high that its use can probably be justified only if it is attended by substantial savings in other directions; for instance, the use of cheap fuel. In the United Kingdom, no very cheap solid fuels are available, and it is unlikely that an oxygen-gasification process could compete economically with conventional production of blue water gas from coke. Hence particular interest attaches to all possibilities of making water gas without using oxygen, if any possible saving in fuel or other costs is involved. The cheapest and most abundant coals in the United Kingdom are the low-rank noncaking bituminous coals in small and ungraded sizes, typically those from the East Midlands coal field, and-fines of high ash content produced in coal-cleaning operations. A process capable of gasifying

Jan 1, 1953

By Louis V. Bender

THIS paper gives a short review of the installation for and the use of gas, as a. fuel, at the Anaconda Reduction Works of the Anaconda Copper Mining Co. Before putting in gas tile fuels used were pulverized coal, lump coal, coke distillate and oil. These fuels are now almost entirely eliminated. For nearly fifty years bituminous coals from Wyoming and Montana fields had been used. These coals were of a good grade, analyzing 11,300 B.t.u. and having an ash content of 12 per cent. When hydro-electric power replaced steam-driven equipment, the coal requirements were reduced; and, on account of improvements in metallurgy and/ or in furnace design, the quantity was lessened. Later, oil and distillate were introduced and used in some of the operations. All of these things tended toward the lessening of the amount of coal used, and had it not been for the increase in the size of the plant, the tonnage used would have been small when the change was made to gas.

Jan 1, 1932

By AIME AIME

AWRDED jointly by the four AW Founder Engineering Societies the John Fritz Medal is generally regarded as the most signal honor that American engineers can confer on a fellow engineer. The roll of 34 recipients contains the names of Lord Kelvin, George Westinghouse, Alexander Graham Bell, Thomas. A. Edison, George W. Goethals, Guglielmo Marconi, and Michael I. Pupin; and among members of the A.I.M.E. now living, Sir Robert A. Hadfield, Herbert Hoover, and Daniel C. Jackling. On the evening of March 1 7 the name of Paul Dyer Merica was formally added to this list of illustrious engineers when the medal was presented to him at a dinner at the Metropolitan Club in New York. The citation read. For important contributions to the development of alloys for industrial uses. Arrangements for the dinner were made by the following committee representing the four Founder Societies: R. C. Allen, George S. Davison, A. A. Potter, and J. B. Whitehead.

Jan 1, 1938

By J. V. Vogel

Jan 1, 1969

By AIME AIME

REGISTRATION and licensing of engineers is now being given consideration by a special committee of the Institute, authorized at the March meeting of the Board of Directors. The subject is one that has recently been or is now actively before engineering organizations in many of the States of the Union. In Washington, D. C., the Washington Society of Engineers and the local sections of ten national engineering societies, including the A.I.M.E., recently had a joint committee investigate the subject: this committee formulating a proposed law that has been presented to Washington engineers for their consideration. At the same time, the committee has summarized the reasons for and against registration of engineers in Washington, D. C. As many of these reasons are of more than local application, they are here reprinted so that all members of the A.I.M.E. may be informed on the subject. It is expected that some report of the Institute's Committee on Registration, State Councils and Professional Development will he made at some forthcoming meeting of the Board of Directors.

Jan 1, 1932

By AIME AIME

ON Tuesday afternoon, Feb. 17, a large and interested audience gathered in the auditorium of the Engineering Societies building to take part in the gold supply symposium that had been arranged for by the Mining Geology Committee. Waldemar Lindgren presided over the gathering and after brief introductory remarks on the international situation as regards lead, silver and gold, called on John Wellington Finch to present an oral abstract of the paper, "Sources and Trends in Gold Production," by R. J. Grant, director of the Mint, and. J. B. Knaebel. This ' paper reviewed the gold production of the world, by countries, since 1845, from the statistical viewpoint, leaving to the later speakers discussion of the statistics.

Jan 1, 1931

By Richard A. Kesler, W. Michael Reed

Grindability or resistance to fine comminution is the fundamental issue involved in the application and sizing of grinding mills. Over the years, many theories for determining the amount of energy required for size reduction to a specified fineness have been proposed. The first published theory, introduced by P. R. von Rittinger in 1867, stated that the energy required for crushing or grinding is proportional to the increase in surface area produced. The surface area of a ton of particles of diameter (d) is proportional to (1/d), therefore the work input per ton for particles of diameter (d) would be proportional to (1/d). The second significant theory is that of F. Kick published in 1885. Kick said that the work required is proportional to the reduction in volume of the particles concerned. If (f) is the diameter of the feed particles and (p) is the diameter of the product particles, the work input relationship would be: [W =Ioq(f/p) 9] The "Third Theory" of F.C. Bond, introduced in 1951, states that the work required is proportional to the length of the new crack tips produced in particle breakage during crushing or grinding and equals work represented by the product minus that represented by the feed. This takes the form: [W=]

Jan 1, 1982

By John J. Egan, A. B. Kinzel, Walter Crafts

The demands of the petroleum and chemical industries for steels to be used in pressure vessels and similar structures at artificially low temperatures are continually increasing, and the writing of proper specifications with suitable tests becomes increasingly important. Likewise, the selection of suitable steels for such applications is of increasing concern to the metallurgist. It is generally recognized that highly alloyed steels of the austenitic stainless type retain their properties even at very low temperatures and represent the best technological solution of the low-temperature steel problem. However, in many instances less expensive carbon or low-alloy steels suitable for service within limited temperature ranges are available. The problem thus becomes one of defining the various factors involved in the production and fabrication of these less expensive steels and determining the temperature ranges in which their properties justify engineering application. Most of the applications involve welded structures, and the heat effect of welding as well as the nature of the weld metal are matters of prime concern. The first problem that the metallurgist faces is the determination of the type of test to be used as a criterion of the performance of the steel in low-temperature service. It has been generally recognized that the static properties of steel as determined in the ordinary tensile test undergo a gradual and relatively slight change as the temperature of test is lowered in the range of current interest; i.e., from room temperature to minus 120' C. It is further generally recognized that the behavior of steel under impact involving notch sensitivity is definitely affected at the lower temperatures. While the major subject of this paper is the effect of grain-refining deoxidizers, of low-alloy additions and of welding on the low-temperature notched-bar impact properties, an inquiry into the general behavior of steel under low-temperature impact testing is included. This is a pertinent portion of the investigation and the results thereof are

Jan 1, 1937

By Klaus M. Zeitler

INTRODUCTION One cannot discuss the subject of "Raising Capital in the 1990s" without having a crystal ball and a reliable fortune teller. This discusses "Raising Capital for the 1990sW, which is what Metal1 Mining Corporation did in 1987. We raised (3166 million in an IPO (initial public offering) that was originally planned for only some (375 million. Why did we raise this money? How did we do it, and why was this IPO so successful? The answer to the first question requires a description of the promoter and principal shareholder of Metal1 Mining Corporation, Metallgesellschaft AG. This West Germany company was founded over 100 years ago in Frankfurt as a trading house for non-ferrous metals. It has developed into one of the world's leading firms in the non-ferrous metals industry. The company's worldwide activities in all areas of that business include mining, smelting and refining, the trading of ore, base and precious metals, the production of semi-fabricated and finished metal products, and the provision of engineering, construction and transportation services. Metallgesellschaft AG has also diversified into many other areas, the most significant of which are manufacturing, the production of chemicals, the development and application of technical and chemical processes, the planning and construction of industrial plants, and activities associated with finance, insurance, shipping and freight forwarding, and the provision of barter and countertrade services. The company maintains a network of more than 100 offices around the world; it employs some 25,000 people in its worldwide activities. [Selected financial data, as of September 30, 1987: (MetaUgesellschafl AG) Working Capital DM 8%.6 million CDNS 672.8 million Long Term Debt DM 568.0 million CDNS 426.2 million Sales DM 14.9 billion CDNS 11.2 billion Net Income DM 87.7 million CDN$ 65.8 million Market Capitalization at April 27, 1987: (Metallgesellschafi AG) Outstanding Shares ~,6oo,o0o DM 1,875 million CDNS 1,407 million] For the fiscal year ended September 30, 1987, Metallgesellschaft AG had, on a consolidated basis, net sales of DM13.3 billion, net income of DM100 million and total assets of about DM7.0 billion. Metallgesellschaft AG established the American Metal Company, a predecessor of AMAX Inc. one of the largest ventures undertaken by Metallgesellschaft AG then was the acquisition, through the American Metal Company, of a majority share in the Mexican Penoles mine, a large lead and silver deposit. METALLGESELLSCHAFT AG Figure 1 depicts an overview of Metallgesellschaft AG before and at the time the initial public offering of Metall Mining Corporation's shares took place. It shows that mining was far from the centre of Metallgesellschaft's activities. Therefore, it could not expect to receive an extraordinary amount of board attention. Thus, mining investments not only had to compare well with other mining opportunities, but were in fierce competition with projects from other divisions. In addition, mining was sub-divided into two separate departments -- domestic and international. These two departments had different management styles and diverging interests which resulted in a minimum co-operation between them. The domestic mining department was primarily interested in the survival of the local mines. These mines were characterized by rising operating costs and declining ore grades. It took a special commitment and continued ingenuity to develop and adjust to local conditions, and modern mining and processing technology, in order to remain competitive, or at least survive within the international mining industry. Local management

Jan 1, 1990

By L. F. Reinartz

FROM the earliest times when our prehistoric ancestors laboriously fashioned crude tools and weapons from meteoric iron until our day when we manufacture steel in 150-ton open-hearth furnaces, the production of iron and steel has played a dramatic and important role in the development of civilization. Progress in the science of refining iron ore into iron and steel was painfully slow for many centuries. The keen scimitars of Damascus, the broadswords of the English knights, the coats of mail of French knights, and the Iron Pillar of Delhi are well¬known examples of medieval metallurgical technique. Expense and the scarcity of raw materials originally limited the distribution of iron and steel products. It was not until the nineteenth century that a determined effort was made to adapt the use of steel to peaceful pursuits. The spectacular and rapid strides made in the manufacture of steel during the last hundred years were hastened by the invention during the decade 1860 to 1870 of two great steelmaking processes-the Bessemer and the open-hearth process.

Jan 1, 1936

By F. F. ESPIE

Giving the keynote address in the final session of a conference dealing with closely related topics has a disadvantage in that much of what can be said has been said. It also has an advantage, however, because it presents the speaker with the opportunity to integrate and analyse the material presented by the various speakers. I would like to look to the near future in Australia and the United States of America, to the risks, problem areas, and changes of a rapidly evolving post-industrial era-an era we are beginning to experience where industry no longer 'calls the tune'. We miners have been quick to point out and emphasize, that ours is a 'high-risk' industry in the world of business and commerce. Yet, clearly those who have survived, and been successful, have learned to anticipate and cope with risk and change. This ability has been a 'distinguishing feature of the industry's leaders who, in market studies and commodity selection, exploration and development, mine planning, metallurgical pro- cessing, and general administration and operation 1. identify areas-of risk or inevitable change, 2. analyse, test and quantify those factors of risk or change, and 3. design methods, systems, equipment to eliminate, moderate, or control or economically compensate for predicted risks or changes.

Jan 1, 1978

By Chandler Morse

RENEWABLE VS. NONRENEWABLE NATURAL RESOURCES Nonrenewable resources, such as minerals, are the inevitable center of attention in discussions of depletion and exhaustion. Nevertheless, it may well be proper to regard some nonrenewable resources as not subject to exhaustion, and renewable resources may sometimes be treated as if they were finite stocks. Thus, the availability of nonrenewable resources is not and probably never will be known completely Chap. 2.5A, and therefore is not subject to firm predictions concerning exhaustibility. Moreover, because exploration and discovery are more or less continuous processes it is often appropriate to regard mineral supplies as flows, and to treat the estimated reserves as working capital, an inventory, continually depleted by use and augmented by discoveries.23 The aggregate economically exploitable stocks of a given mineral are seldom estimated (or estimatable) with precision, as Chap. 2.5A shows, and even when they are, forecasts concerning years of remaining life can be and often are falsified by changes in one or more of the multidimensional conditions of supply and demand; or the productive services formerly derived from an exhausted stock may continue to provided without material impairment by one or more substitutes b Conversely, the renewable resources are all subject to depletion when the rate of use exceeds the natural or induced rate of replenishment, and cases of exhaustion or near exhaustion, as through soil erosion, overcuttmg of forest lands, and overfishing, are rather common c Where exhaustion is a clear possibility the resource may either be exploited on a consciously adopted "sustainable yield" basis or be treated as an exhausting asset." In some cases, conscious treatment

Jan 1, 1976

By Henry Rawdon

ANY laboratory corrosion test, as judged from the practical point of view, is valuable only to the extent that it foretells what will, in all probability, occur in service. Such a test is most properly to be considered as a "pilot test, " that is, a test which indicates the direction along which action may be expected to occur rather than as a truly quantitative test which would be expected to tell just how and to what extent the action would proceed. It is generally recognized that laboratory corrosion tests should be chosen with particular reference to the character of service expected for any particular type of metal, so far as it can be foreseen. Even when this requirement has been fulfilled, however, the question whether the actual service behavior of the material is in accordance and general agreement with predictions based upon such laboratory tests is always a pertinent one. The information available in the technical literature bearing on the correlation between the service behavior of metals from the corrosion standpoint, and the results obtained with the same metals in laboratory corrosion tests is very meager, indeed. The results which have been obtained in weather-exposure tests of sheet duralumin which form the body of this discussion are presented here for their bearing on this particular phase of the problem of the corrosion resistance of duralumin. Although the exposure tests described have not been completed, in the sense that all of the tests, in the series initially laid down, have been accomplished, still the general trend shown by the results is so clear that a number of definite conclusions at this stage (subject, of course, to possible modification in the light of later results) are believed to be warranted. The tests reported upon here form one phase of the much broader study of this subject which has been under way for several years in which the National Advisory Committee for Aeronautics, the Bureau of Aeronautics of the Navy Department, the Army Air Corps and the Bureau of Standards have cooperated. Without the very helpful cooperation of the manufacturers in furnishing the

Jan 1, 1929

By Raymond Franz

Of the many types of capital equipment found in a surface operation, draglines and mining shovels are probably subjected to the most severe service. Yet, some excavators have seen a generation or more of continuous service-proof, if any is needed, of their ruggedness. To keep these expensive pieces of machinery operating, a continuing maintenance program which includes field weld repairs is essential. During an excavator's working life, minor cracks may appear in parts of the steel structure, caused by fatigue and sometimes material defects-defects so small they could not be detected during manufacture.

Jan 6, 1978