Search Documents

THE story of Miami really is two stories. First, that of an excellent Porphyry Copper mine, ably managed as a business enterprise, and always among the leaders in technical progress. Concentrating its first ore in 1911, it had by 1925 paid dividends totaling $30,000,000 or $40 per share on stock that had cost the public $5 per share in March, 1908. The ore, containing 2.5 per cent copper at the start, had become progressively leaner but the recovery had tended to improve. Production costs had gone up during the World War and the early post-war period; and had come down again. In all these respects it had followed the norm. If the mine had been abandoned as exhausted and the company had been liquidated late in 1925 (a program that had been given earnest consideration in 1924), Miami would have gone down into history a first-rate mining venture; as an active and progressive participant in the great Porphyry achievement. But Miami was not liquidated in 1925; instead it started to write the record of its second and really amazing story. Near the old mine was a large body of low-grade ore containing, in place, less than 20 lb. of copper to the ton, and without, incident- ally, any considerable sweetening of gold and silver. Any method of underground mining that was cheap enough would certainly entail some dilution, so that ore as sent to the concentrator necessarily would average much less than 20 lb. As a matter of record, the average for 1929 was 16.6 lb., from which 11.726 lb. was recovered as concentrate. As already said, the exhaustion of the older orebody during 1925 was foreseen; but in 1924 the decision was reached to enlarge the concentrator and develop a new mine. An expenditure of $2,500,000 was entailed in this program. By October, 1925, the

Jan 1, 1933

Jan 1, 1879

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

The Grand Isle sulfur mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, La. The deposit is on acreage covered by oil, gas, and mineral leases originally issued in favor of Humble Oil & Refining Co. by the State of Louisiana which were continued, maintained, and redesignated by the U.S. Department of the Interior after passage of the Outer Continental Shelf Lands Act. The sulfur deposit was discovered in 1949 when Humble Oil & Refining Co. penetrated more than 200 ft of sulfur-bearing limestone in a zone between 1813 and 2075 ft below sea level. In 1954, Humble drilled ten more sulfur prospect holes, eight of which encountered sulfur ore. On September 19, 1956, Freeport Sulphur Co. acquired from Humble Oil & Refining Co, the sulfur rights underlying the tracts, and the actual design of the installation began the same month. The first structural contract was awarded in December 1957 and offshore erection began in June 1958. The initial phase of construction has been completed and production by the Frasch process commenced in April 1960. The estimated total cost of the project is $30 million, of which $8 million is the extra cost incurred by the necessity of offshore operations. More than $22 million was expended before production was started. GEOLOGY OF DEPOSIT Grand Isle is the third largest sulfur deposit in the U.S. The orebody embraces several hundred acres, but its outer limits are yet to be defined to the northeast, east, and south. Most Gulf Coast sulfur deposits occur in a caprock mantle of calcite (referred to as limestone), anhydrite, and occasionally gypsum, which covers the apex of an intrusive mass of salt. Commercial quantities of sulfur are usually confined to the calcite or limestone member. Most often such limestone is completely enclosed by dense anhydrite below and impervious sediments above, which effectively form a closed reservoir. The depth of the Grand Isle orebody ranges from 1800 ft to 2500 ft below sea level. Within the present boundary, the sulfur-bearing limestone varies in thickness from 220 ft to 425 ft, while the sulfur content varies an average of about 15 pct in the leanest hole to an average of about 30 pct in the richest. Rock containing less than 5 pct sulfur is not classed as ore, and holes assaying less than 20,-000 long tons per acre of sulfur in place are not considered commercial offshore. The sulfur enrich-

Jan 1, 1961

By George Holderer

THE Enos Coal Mining Co. owns an area underlaid by coal, of approximately 5000 acres. This property is situated 9 miles from Oakland City, in the southern part of Indiana. The mine has been in operation 5 years, during which time some 350 acres have been stripped, and stripping is now proceeding at the rate of about 100 acres per year. TOPOGRAPHY These coal lands consist of gently-rolling agricultural fields which in times past were farmed for wheat. There is no timber and but very little brush to contend with. The overburden varies from 10 to 60 ft. in depth. A thin bed of slate overlies the coal, followed by limestone, which varies from 3 to 15 ft.; this, in turn, is followed by sandstone, slate, shale and clay. There is a very wide variation in the thickness of all of these beds. The coal has an average thickness of 5 ft., and is a good grade of high-volatile bituminous. MINING OPERATIONS Briefly, the sequence of operations is: drilling holes with churn drills; blasting with L. 0. X.; stripping overburden to, uncover coal and, finally taking up the coal, which is sent to a tipple for cleaning and sizing. In order to show what is being accomplished by the use of L. 0. X., results will be shown from May to November, 1926, inclusive, and compared to the same period in 1925. No work was done in No. 1 pit during May, 1925, hence all figures are unduly low for this month.

Jan 2, 1927

By Yu A. Chernegov

Building up the USSR's economic strength was the result of all the achievements and successes of our economy. The Soviet Union was the first to begin planned guidance of the economy. The mining industry of the USSR, which holds the first place in the world output of mining production, has always been considered as the main raw materials basis of the country's economy. High and stable development rates are a feature of planned economic management, based on the social ownership of the means of production. During the past ten years from 1965 to 1875 the national income used for consumption and accumulation increased practically by 1.9 times. There has been no inflation, no unemployment in the Soviet Union for about forty years already. High and stable growth rates of the production of mining industries and that of the branches, which are their direct consumers are characterized by the data in table I. The achievements and successes of the economy's development are to a great extent determined by the three planning components, which are as follows:

Jan 1, 1977

Andy H. Vassiliou – Introduction Ladies and gentlemen,.good evening and welcome to the Paul F. Kerr Memorial Symposium dinner. I believe we are all here to honor the memory of a great teacher and advisor, and a true friend -- Professor Kerr, or Dr. Kerr, or to most of us who were his students, "Pappy" Kerr. Most of us who attended the Paul F. Kerr Memorial Symposium earlier today at the New York Hilton had the opportunity to read, or listen to, or discuss scientific papers presented in honor of Dr. Kerr. In addition, all of the speakers had the opportunity to reminisce about their association with Dr. Kerr, who was credited as having contributed substantially to their graduate education and the development of their careers. Dr. Kerr's two daughters -- Ruth and Nancy -- who attended the Symposium at the Hilton are also here with us tonight. I think we should keep tonight's festivities on an informal basis since we are all old friends or former students of Dr. Kerr. Some of us may want to say a few words about our experiences at the time we were students at Columbia, and hopefully include some anecdotes relating to Professor Kerr. I would like to invite everyone to do so, but first we have arranged for two of us to be the lead speakers, whom I will introduce in a few moments.

Jan 1, 1985

By H. T. Kennedy, S. M. Avasthi

An equation developed for gaseous hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 0.73 percent when applied to 264 natural gas and condensate systems including 2,043 PVT points. Another equation developed for liquid hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 1.12 percent when applied to 346 crude oil systems including 1,759 PVT points. Both equations require composition of the mixture to be expressed as mole fraction of methane through heptanes-plus, hydrogen sulfide, nitrogen and carbon dioxide, together with the characteristics of the heptanes-plus fraction in addition to the temperature and pressure. The equations cover wide ranges of the variables involved, and their accuracy is considerably better than that of other available methods. The equations were differentiated to allow calculation of the coefficients of isothermal compressibility and isobaric thermal expansion. (In this paper the coefficient of isothermal com-pressibility and the coefficient of isobaric thermal expansion will be expressed as compressibility and thermal expansion coefficient, respectively.) Equations to calculate these quantities are presented. INTRODUCTION Calculations of reservoir performance for petroleum reservoirs require accurate knowledge of the volumetric behavior of hydrocarbon mixtures, both liquid and gaseous. Compressibilities are required in transient fluid flow problems, and thermal expansion coefficients are important in thermal methods of production. An accurate laboratory investigation of the PVT behavior of each reservoir fluid encountered would be costly and time consuming. For this reason various correlations for predicting fluid properties have been developed and recorded in recent literature. Correlations have been presented in the form of graphs, tables and equations. Since an increasing number of studies are being conducted with the aid of electronic computers, recent efforts have been directed toward development of correla-tions suitable for computer programming. Application of computers permits the use of more complex correlations which otherwise are not feasible. Moreover, methods for predicting reservoir performance, particularly those based on the compositional material balance, depend upon the capability of accurately expressing the molal volumes and other fluid properties as functions of pressure, temperature and composition. The coefficient of isothermal compressibility c is defined by

Jan 1, 1969

By Mark David Rankin

This paper represents a general assessment of the primary factors driving the market for mobile offshore drilling rigs and the utility of those factors as choice variables for the offshore drilling program planner.

Jan 1, 1982

By Charles B. Dudley

DEAR SIR: It is now nearly three years since my first report to you on the subject of steel rails was written. That report, as you will remember, dealt principally with the question of the relation between the chemical composition and physical properties of steel rails end their power to resist crushing and fracture in actual service. Other matters were referred to or touched upon in that report, but the main question was, Why do some rails crush or break in service while others do not? Yon will doubtless remember that the principal conclusion arrived at was, that the softer rails are less liable to Crush or break in service than the hard ones. Or, in other words, so far as conclusions could be drawn from the chemical analysis and physical test of 25 samples of steel rails which had actually been in service, these conclusions were that those rails which have the smaller amounts of carbon, phosphorus, silicon, and manganese are less liable to crush or break in service than those which have larger amounts of these elements. Or, again, looked at in the light

Jan 1, 1881

By Sherwin F. Kelly, Bela Low

THE WORK OF THE DRILLER and of the oil geologist is seriously handicapped by the impossibility of actually seeing what is going on inside a borehole as it is being drilled. Visual information of the position and condition of the casing, and of the characters and attitudes of strata passed through would be of inestimable benefit. The best substitute for putting a periscope down a hole is the taking of photographs of its interior at points where information is desired. An apparatus for this purpose has been constructed by Dr. Thomas Reinhold, of Heemstede, Holland, and one instrument of his design has been put into practical use by the Geological Survey of The Netherlands in searching for water. To the best of our knowledge, this instrument has not been applied to oilfield problems, although the possibility has been mentioned in the one or two brief notices of the camera which have appeared in the literature.' The purpose of presenting this description of the instrument, with some examples of its work, is to suggest that it might be adapted to serve a variety of useful purposes in American oilfields, and with the hope that discussion will bring out any modifications necessary to make the apparatus more valuable to drillers and geologists.

Jan 1, 1932

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Engineer of many years' experience in mining engineering, construction, public works, contracting, water-power development and operation, having heretofore retired on a sufficient competence, wishes to have employment with thoroughly reputable concern where his experience would be of value; the question of remuneration is of secondary importance. A-2591. Engineer, in military service nearly two years, desires, when discharged, to secure permanent position offering future opportunities. Experienced as mechanical and metallurgical engineer, investigator, teacher. Technical graduate and post-graduate from two of best American schools. Ability as executive, organizer and industrial leader. Especially fitted for industrial position of administrative nature or as technical assistant to industrial manager. Salary expected $4500 to $5000. A-2619. Member A. I. M. E., age 36, twelve years' experience in smelting and hydrometallurgy of copper ores, desires research or works position with responsible company. Speaks fair Spanish. Can handle men. Will welcome difficult metallurgical problems. Salary $5000. A-2627. Mining engineer, recently discharged from the Army as Captain, Engineers, age 38, 15 years' experience in the Southwest and in Mexico in gold, silver and copper mining, engineering, surveying, sampling and assaying, with special training in prospect and mine examination and the development of prospects. Speaks Spanish; immediately available; references. A-2136.

Jan 6, 1919

By L. B. Davidson

The petroleum literature contains many reports on the relative permeability properties of porous media. However, only recently have studies of relative permeability at elevated temperatures been made.1 -5 Each of these studies presents relative permeability data on water-oil systems in linear sandpacks or sandstone cores under isothermal conditions. The results of these investigations are dissimilar. Edmondsonl found that in Berea sandstone a temperature-dependent effect was present, while Shilobod,2 using the same material, found no temperature dependence after normalizing for initial water saturation. Workers at Texas A&M U.3-5 found that the ratio kw/ko was temperature dependent in an unconsolidated system. The differences in results of these studies are probably a consequence of differences in the material employed, in the experimental procedures followed, and in the properties of the porous systems used. This paper describes an experimental investigation of permeability ratio temperature dependence, conducted to clarify some of the results obtained by previous workers. Each experiment described in this paper involved the isothermal displacement of Chevron No. 15 white oil by either nitrogen, steam, or distilled water and displacement of water by nitrogen. All permeability ratios were calculated using the Welge procedure. Values of the water-oil permeability ratio were obtained over the temperature range 75OF to 540°F. Results indicate the ratio is temperature dependent at low water saturations, probably due to interfacial effects. However, as the saturation is increased, temperature dependence decreases until, above some minimum saturation, the ratio becomes insensitive to temperature. Previously published work indicates that the dependence reappears at very high water saturations, a region of the ratio curve not completely examined in the present study. It appears that water-oil permeability ratios are temperature dependent at the extremes of the ratio curve where changes in interfacial tension with temperature induce variations in residual saturations. Between the extremes, there is a region in which the permeability ratio is insensitive to temperature. The size and location of this region is probably a function of the characteristics of the porous system. Gas-oil permeability ratios calculated from nitrogen-white oil displacement experiments indicate a definite temperature dependence over the range 75OF to 500°F and over the entire gas saturation range studied. Evidence discussed in this report indicates that this dependence is a consequence of molecular slippage in the gas phase. This is an extension of the Klinkenberg effect6 to two-phase systems at high temperatures (the existence of slippage in two-phase systems at room temperature has been demonstrated7). Evidence for a similar source of temperature dependence in superheated steam-white oil experiments

Jan 1, 1970

By Pervez Patel, Martin G. Frohberg, Demetrios Papamantellos

Model experiments were carried out on the mass transfer of iodine between n-hexane and a 4 2 X 10-3 M aqueous sodium hydroxide solution. The influence of mechanical stirring by means of small gas bubbles (ca. 0.01 ml in volume) on mass transfer was examined in independent experiments. The results were described with the help of the penetration theory and in the case of bubble stirring with the help of a mathematical model based on this theory. S LAG-METAL reactions, especially those in steel-making processes, often occur under conditions where gas is evolved in the form of bubbles that break through the slag-metal interface. It is known that stirring by means of bubbles increases the mass transfer coefficient, but there has been very little quantitative work done in this field. Because of the difficulties that attach to experimental work at high temperatures this study was confined to model experiments at room temperature. EXPERIMENTAL APPARATUS The transport of iodine from an n-hexane layer into a weak sodium hydroxide solution was studied a) with stirring by means of bubbles and b) with mechanical stirring. The apparatus for the experiments with bubbles consisted of the cell, two Dreschel bottles filled with hexane in order to saturate the nitrogen flow, one flow meter, and a nitrogen gas cylinder fitted with a fine-regulating valve. Fig. 1 shows the cell consisting of a glass cylinder 33 cm in height with an overall diameter of 7.5 cm embedded in a copper flange. The flange is connected to a Plexiglas plate and to the gas inlet. The Plexiglas plate has holes of 0.2 mm diam bored into it which are spaced 1 cm from each other. For the experiments with mechanical stirring the bottom of the cell was sealed off by a Plexiglas plate. The upper layer was stirred by means of a glass stir-rer and the bottom layer with the help of a magnetic stirrer in a counter rotatory direction. Both stirrer speeds could be varied continuously. EXPERIMENTAL PROCEDURE Iodine dissolves in n-hexane producing a stable violet color thus enabling the iodine concentration in

Jan 1, 1970

By J. F. Breedis

The stabilization of austenite in Fe-Ni alloys against martensitic transformation after reversion has been attributed' to the lattice imperfections remaining from previous transformation. More recently, however, such stabilization has been associatedzy3 with compositional changes which occur in martensite during slow heating. Dislocation arrangements in deformed austenitic stainless steels strongly influence transformation to martensite on quenching.4 Therefore, it is of interest to observe the transformation behavior of stainless steel after reversion, especially since previous studies have been confined to Fe-Ni alloys. The transformation-product morphology also differs in the two iron-alloy systems;6 plate martensite forms in the latter while stainless steel transforms to lath-type martensite. Samples of Fe-16 wt pct Cr-12 wt pct Ni (maximum C + N = 0.005 wt pct, 0 = 0.02 wt pct), prepared by vacuum melting and casting from high-purity components, were annealed at 900°C for 24 hr, after cold rolling to produce a 40-p grain diameter. The M, temperature of this alloy is -80°C and samples are fully austenitic after annealing. The amount of martensite present after quenching, annealing, and requenching was determined magnetically, to within 0.01 wt pct, using a vibrating specimen magnetometer. Nearly 14 pct of martensite forms during the initial quench in 1 min at -196°C. Two-min and 2-hr anneals were done in air and in evacuated quartz capsules, respectively. All specimens were electro-polished before making the magnetic measurements.

Jan 1, 1967

By T. S. Blair

I feel a certain sense of responsibility in bringing before you the subject of the direct process in iron manufacture. I am aware that, in such a body as I have now the honor of addressing, there are few who are not already so well informed upon its past history that it would be a weariness to them to listen to anything else than an account of practical success. Yet, to claim that success involves so much that, if I do not make good my claim, I deservedly expose myself to severe criticism. The whole literature of the art, so far as it relates to the direct process, is, up to this time, but a history of failure. It is safe to say that more money, time, and talent have been fruitlessly spent in the pursuit of this object than in all the other unsuccessful efforts in the whole line of iron metallurgy. A distinguished authority in patent law has remarked that " the invention records of the United States and of foreign countries are filled with the waifs and abandoned relics of these abortive struggles." Dr. Percy, whose great work may be taken as an epitome of all that was worth mention, whether useful or curious, in pig-iron metallurgy, up to the date of its publication (1864), after giving elaborate accounts of various attempts at the direct process, condenses his own opinion of all that had been then effected, into a brief but summary comment upon a pamphlet of one of the sanguine inventors who had said: "It is evident that the present mode of working iron

By Leslie C. Richards

The competitive position of producers of industrial minerals depends upon the delivered price of their product. Freight charges are a major factor in the sales to consumers. A comparison of freight rates on movements of limestone and silica rock in the Pacific Northwest shows a wide variance in mills per ton mile for like hauls, thereby favoring some localities over others. Introduction: Sooner or later the potential miner of industrial minerals reaches the conclusion that of the various factors he must consider, the marketing of his product is. the most important. The sooner he realizes this the better, as successful industrial mineral producers .will confirm. Herein lies a difference between i.ndustria1 mineral mining and metal mining. Often in the latter, technical problems of mining or concentrating are equal to or even surpass those of marketing. This is not meant to imply that there are no problems in mining and beneficiation of industrial minerals, but these usually are outweighed by the problem of marketing. Recentlv. an official of a nationally known corporation :i the elecl.ro-metallurgical industry made an industrial mineral survey in the Pacific Northwest. In the course of his investigation he interviewed producers and potential producers of the various industrial minerals scheduled for use in the plant now being constructed in this area. He stated that he was interested in only three factors: namely, (1) Can your product meet our specifications? (2) Are you able to supply our tonnage requirements? and (3) What will be the delivered price? If there are several sources of supply of sufficient grade and tonnage, as is often the case in the Northwest, then the third factor becomes the important and deciding one. While industrial minerals are usually sold f.0.b. cars with the freight being paid by the buyer, it is the delivered and riot the f.0.b. price that determines the competitive position of the producer and his industrial mineral product. Unfortunately for both the consumers and producers of industrial minerals in the Northwest, the sources are generally a considerable distance from the markets. This necessitates long rail hauls, for which transportation charges make up the largest share of the delivered cost and the delivered price of the product. Is it any wonder then, that rail rates play such an important part in the marketing of industrial minerals? In order to sell his product, the producer must be able to deliver to the market at a competitive price. It must be remembered that his largest cost factor is rail transportation, and that he is limited to markets that he can reach competitively. Since the cost of rail transportation is so important, let us compare various freight rates in the Northwest and attempt to determine their influence on marketing. A study of all rates on all industrial minerals transported in this area, is beyond the scope of this paper. For the purposes of comparison, let us consider limestone (broken, crushed, or ground), and silica rock. These are widely used industrial minerals, and are carried by several different rail routes from.the sources of supply to the centers of consumption in the Pacific Northwest. Markets and Sources of Supply: Limestone has a number of uses in western Oregon and Washington. Among them are agricultural lime for the soils of the Willamette Valley and southwestern Washington; paper rock for the mills in such cities as West Linn, Oregon City, Newberg, St. Helens, and Salem, Oregon, and Camas and Everett, Wash.; chemical and metallurgical-grade limestone for the metallurgical plants centering around Portland, and the Tacoma-Seattle areas'; and sugar rock for the sugar refineries at Toppenish, Wash., and Nyssa, Oregon. Since limestone for cement manufacture is generally processed near the quarry, transportation

Jan 1, 1951

By Leslie C. Richards

Sooner or later the potential miner of industrial minerals reaches the conclusion that of the various factors he must consider, the marketing of his product is. the most important. The sooner he realizes this the better, as successful industrial mineral producers .will confirm. Herein lies a difference between i.ndustria1 mineral mining and metal mining. Often in the latter, technical problems of mining or concentrating are equal to or even surpass those of marketing. This is not meant to imply that there are no problems in mining and beneficiation of industrial minerals, but these usually are outweighed by the problem of marketing. Recentlv. an official of a nationally known corporation :i the elecl.ro-metallurgical industry made an industrial mineral survey in the Pacific Northwest. In the course of his investigation he interviewed producers and potential producers of the various industrial minerals scheduled for use in the plant now being constructed in this area. He stated that he was interested in only three factors: namely, (1) Can your product meet our specifications? (2) Are you able to supply our tonnage requirements? and (3) What will be the delivered price? If there are several sources of supply of sufficient grade and tonnage, as is often the case in the Northwest, then the third factor becomes the important and deciding one. While industrial minerals are usually sold f.0.b. cars with the freight being paid by the buyer, it is the delivered and riot the f.0.b. price that determines the competitive position of the producer and his industrial mineral product. Unfortunately for both the consumers and producers of industrial minerals in the Northwest, the sources are generally a considerable distance from the markets. This necessitates long rail hauls, for which transportation charges make up the largest share of the delivered cost and the delivered price of the product. Is it any wonder then, that rail rates play such an important part in the marketing of industrial minerals? In order to sell his product, the producer must be able to deliver to the market at a competitive price. It must be remembered that his largest cost factor is rail transportation, and that he is limited to markets that he can reach competitively. Since the cost of rail transportation is so important, let us compare various freight rates in the Northwest and attempt to determine their influence on marketing. A study of all rates on all industrial minerals transported in this area, is beyond the scope of this paper. For the purposes of comparison, let us consider limestone (broken, crushed, or ground), and silica rock. These are widely used industrial minerals, and are carried by several different rail routes from.the sources of supply to the centers of consumption in the Pacific Northwest. Markets and Sources of Supply: Limestone has a number of uses in western Oregon and Washington. Among them are agricultural lime for the soils of the Willamette Valley and southwestern Washington; paper rock for the mills in such cities as West Linn, Oregon City, Newberg, St. Helens, and Salem, Oregon, and Camas and Everett, Wash.; chemical and metallurgical-grade limestone for the metallurgical plants centering around Portland, and the Tacoma-Seattle areas'; and sugar rock for the sugar refineries at Toppenish, Wash., and Nyssa, Oregon. Since limestone for cement manufacture is generally processed near the quarry, transportation

Jan 1, 1951

By Hiland G. Batcheller

HISTORY shows that the nation which makes the most steel is the most likely to win wars. Today the course of war shows that the nations which get there first with the most steel of the right kind will be the ones to win. Not only the most steel, mind you, but the right kind. Adequate production, which was enough for victory before the days of totally mechanized warfare of 1943, must now be accompanied by still better quality as well as more effective distribution. Further, both production and distribution must be flexible enough to permit rapid shifts from one weapon to another for use in varying elements in varying geographical areas. Thus the problem of making enough steel of the right kind at the right time in the face of changing requirements dictated by experience has been and will remain highly complex. This does riot permit us to ease our restrictions on nonessential use. War is a complex business, like the job of making steel for war. Each time we solve one problem, another pops its head up. Yet we are making some progress.

Jan 1, 1943

By C. K. Leith

THE outstanding fact of the mineral world today, at home and abroad, is the surplus of current production, and particularly of capacity for production, over current requirements. This is not by Any means a new condition, but never before has it loomed up in such' menacing form. - Those of us who have devoted most of our professional efforts to the discovery and development of 'new mineral supplies now suddenly find ourselves with the job apparently accomplished, waiting for some one else to find an outlet for excess mineral production before we can further. The management of the industry is in much the same boat. The psjrcho16gy of the industry has been so grooved in the direction of acquisition of, minerals that at the present moment the mineral industry confronts the new problem of surplus in more or less of a daze.

Jan 1, 1931

By Frank Firmstone

In April, 1873, No. 2 furnace at the Glendon Iron Works being out of blast, it was decided to alter it from an open to a closed top. The three side flues, through which a part of the gas was formerly taken off, were 15 feet below the top, and as, for various reasons, it was not convenient to cut new flues through the brickwork at the top, as is commonly done with closed-top furnaces, a modification of Coingt's charger was employed. This apparatus, as figured by De Vathaire,* consists of a cup or hopper, like that used with the cup and cone, and a central pipe for taking off the gas, which descends some distance into the furnace, and has a projection around it forming a seat for a ring of a triangular cross-section, which closes the opening between the cup and the central gas-pipe. The charge is put into the cup, and by lowering the ring, is thrown into the furnace, a part going outside of the ring toward the walls, and a part through the inside toward the gas-pipe. In this form the apparatus was not applicable, for: 1st. With a gas-pipe three feet in diameter, in a top eight feet in diameter, the openings left by lowering the ring would not be large enough to let lump coal pass through. 2d. For the charger to shut tight, the ring must bear equally against the projection made for it on the gas-pipe, and against the edge of the cup. This would not be difficult to effect when the apparatus is first put up, but a comparatively small change in the relative position of the parts, such as is almost certain to occur from expansion, would cause the ring to touch the pipe or the cup, whichever happened to be the lower, first, and leave a leak between it (the ring) and the other. In the plan adopted (Figs. 5 and 6, Plate I), the central opening in the ring is closed by the bottom of the gas-pipe, whereby more room is left for the passage of the stock when the charger is open, than if the pipe descended into the furnace; and the pipe, instead of being rigidly supported, rests on the ring, when the charger is closed, and follows it for two or three inches as it opens, until stopped by the counter-balance lever C. When the ring is raised to close the furnace top, it comes in contact first with the bottom edge of the gas-pipe, then both are raised together, until stopped by the ring touching the edge of the cup. In this way a good joint is made at both places.