Search Documents

By P. CHARTERIS A.

THE following scanty notes on the Roumanian oil-region may serve as an introduction to more detailed future study and description. The Roumauian oil-belt, follows the outer edge of the sweep of the Carpathian Mountains, and may, in a broad sense, be regarded as a prolongation of the Galician belt. It is distributed over a tract of country from 300 to 400 miles in length, with a width of from 15 to 20 miles, and is believed to cover an area of at least 20,000 hectares (59,420 acres). The Government claims that 16,000 to 17,000 hectares of its land is petroliferous. The primary deposits of petroleum are considered to be in the Padeogene (Oligocene) and the Neogene (the salines of the Miocene) formations. Most of the other repositories, especially those of Muntenie, are only secondary, the petroleum there having been introduced by the orogeneric movements which raised the Carpathian Mountains. The oil-field has been divided by the Roumanian survey into two regions, the Flysch and the Sub-Carpathian, as is shown in the accompanying sketch-map, Fig. 1.(p. 518). So far as is yet, known, practically all the seepages and .productive pits and wells are situated oil anticlinals. Those which outcrop in the Flysch region. (called Paleogene anticlinals), as indicated in the sketch-map, Fig. 1, are : Solontz, Middle Oligocene; Moineshti, Moineshti and Tagu-Ocna-beds of the Eocene.

Jul 1, 1906

By J. B. Austin

IN considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based . upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these effi-ciencies are more useful than others, yet all are instructive; for a knowl-edge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermo-dynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By James Boyd

THE Bureau of Mines for a number of years has been seeking additional ways and means of improving the efficiency of its operations and increasing its service to the public. It has become obvious that changes in the organization of the Bureau are essential to a more effective accomplishment of its functions and objectives. The old organization was defective in meeting current needs in that the Bureau's field activities were neither sufficiently coordinated with the national program nor were they particularly responsive to local needs of the mineral industries. Further, the traditional organization hampered the efforts of the Bureau to obtain, analyze and provide to the policy-making agencies of the Government essential information and advice in such a form that the requirements of domestic industry could be fully taken into consideration in the development of domestic and foreign policies. Consequently, the Bureau has now modified its organizational structure.

Jan 1, 1949

By R. R. Harvey

Recent evidence has indicated that the films forming at crude oil-water interfaces are the result of naturally occurring su,rface-active components in the crude oil rather than oxidation products resulting from exposure of the oil to air. Since the presence of such films may strongly affect the displacement of oil from porous media, a knowledge of their composition and formatiorz is of fundamental importance. In this study, without the assumption of a specific mechanism, film formation is considered to involve the transfer of a weakly surface-active species in solution in the oil to the oil-water interface. The film gas law and the Gibbs adsorption equation may thus he applied to the system. The rigid films which form upon decrease of the oil-water interfacial area are considered a result of the very slow rate of re-solution of the film material into the oil. When the shrinkage of the interface is very rapid, the amount of film material leaving the interface is negligible, and the system may then be treated in the same manner as an insoluble film. The combination of these treatments leads to a new concept of the film factor in which it may he quantitatively related to the concentration of film-forming material at the interface. Suitable experiments can then yield the following information. 1. Original concentration of surface-active species in the oil. 2. The change of concentration with time. 3. Concentration of surface active species at the interface. 4. The change of this concentration with time. 5. Interfacial tension of the system at any time and its variation with time. 6. Equilibriunz concentrations for a given set of conditions. 7. Concentration requirements for solid film formation. 8. Molecular diameter of the adrorbed species. These calculations may be made solely from data taken from measurements on the original oil. While using the pendant drop method of interfacial tension measurement of crude oil-water systems, Bartell and Niederhauser' remarked on the thin, transparent, pliable, solid films or membranes which were often formed at the interface between crude oil and water. As a result of their observations of these films, Bar-tell and Niederhauser concluded: 1. The films are formed by material from the oil adsorbed at the interface rather than by a reaction at the interface. 2. The adsorption of the film-forming material is a rather slow process. 3. There are good indications that the process is reversible; i.e., the film constituents may re-dissolve into the oil. 4. The film will spontaneously spread over any new surface formed. 5. The process of adsorption at the interface is accompanied by a decrease in the interfacial tension of the system. Although they had proved that film formation was not due to a reaction at the interface, Bartell and Niederhauser were unable to demonstrate conclusively whether these film-forming constituents were present in the original reservoir oil or whether they were formed as oxidation products after exposure of the oil to air. Recent evidence seems to point to their presence in the original oil. Although the true nature of the film-forming constituents is still uncertain, these conditions would be fulfilled by the assumption of the presence of a slightly soluble surface-active component in the original oil. This component would migrate to a freshly formed interface because it would thereby lower the free energy of the system. The component at the surface constitutes an expanded monolayer which would become compressed, upon retraction of drop, due to the slow rate of re-solution of the film components into the bulk of the oil. It is possible, by involved extraction processes, to separate or at least concentrate this film-forming fraction. However, using the assumptions made above, the technique of monolayer film study may be applied to reveal much of the nature of the adsorbing material without resorting to an actual separation of the film-forming constituents.

By Laurence Pellier

Electron microscopical studies were made of the effect of sensitization at 1200oF on a Type-.104 stainless steel with high carbon and low nitrogen and oxygen contents, after solution annealing and after cold working. The loci of the carbide precipitates in the early stages of sensitization were followed in dry stripped plastic replicas. Some observations were made by direct electron transmission on thinned films. Intragranular dislocations showed a high degree of stability through the annealing necessary to produce sensitization. I HE present work was undertaken to determine the effect of sensitization, at 1200°F, for 1/2 hr, on the electron microstructure of a Type-304 stainless steel with high carbon, and low nitrogen and oxygen contents, after solution annealing and after cold working. Many electron microscopical studies of sensitization of 18-8 stainless steels have already been made. Most of them utilized extraction replicas, from which the morphology and composition of the precipitated carbides could be established.'-" ry stripped replicas were seldom used for such studies, although it was demonstrated that they are applicable, in general, to EurveYs of the general microstructure of many alloys' and, in particular, to the observation of precipitated carbides in austenitic stainless steels.3

Jan 1, 1963

By H. E. Cline

Solidification of Pb-Sn alloys ranging in composition from 1.2 to 56 at. pct Pb ws observed with polarized light. Lamellar structures were observed over a larger range of compositions in alloys containing excess tin than excess lead, as expected from constitutional supercooling. The occurrence of pools of supercooled liquid surrounded by lead is explained by the difficulty in nucleating tin. Cells and dendrites weve observed in tin-rich alloys. Evidence was found that the degenerate structure formed at low growth rates, the formation of faults, and abrupt changes in composition and structure can be attributed to non-steady-state growth. The apparent interface shape was observed to have deep grooves at the interphase boundaries. HUNT and Jackson have observed the shape of the interface during growth of organic eutectics. They observed the formation of lamellar faults and shape instabilities upon changes in growth rate. The lamellar structure in these organic eutectics was not restricted to the eutectic composition. Recent work by Mollard and Flemings2 indicated that Pb-Sn alloys from 12 to 26 at. pct Pb could be solidified with a lamellar or rodlike structure if a sufficiently steep temperature gradient was used at a slow growth rate. Observations of the solid liquid interface of the Pb-Sn eutectic were made by Davies3 using polarized light. Photographs were at too low a magnification to determine the interface shape, but he has concluded that tin was the leading phase. In the following experiments, solidification of a range of Pb-Sn alloys from 1.2 to 56 at. pct Pb was observed using polarized light, to determine the factors controlling stability of the lamellar structure. EXPERIMENTAL Procedure. One hundred-gram ingots of alloys prepared from 99.999 pct pure Pb and Sn were cast into graphite molds under argon. The compositions of the alloys were 1.2, 6, 12, 26, 36, 46, and 56 at. pct Pb. Two-gram pieces were melted between two cover glass slides which were squeezed into a 1-mm separation. Samples were then observed under polarized light in a hot stage shown in Fig. 1. A long working distance objective designed for viewing at 500 times was used. Photography was made difficult by the lack of illumination and contrast at these high magnifications. By using an elliptical polarization compensator, as suggested by A. Holik, the contrast and illumination could be optimized. Photographs could be taken only at slow growth rates to avoid excessive interface motion during the 15-sec exposure used. The solidification rate was varied by increasing or decreasing the power to the heater. It was found that insulation was necessary to avoid undesired growth rate fluctuations. The temperature gradient, as measured with two thermocouples 1 cm apart, was 80" ± 20°C per cm during all the experiments reported here. The advantage of this procedure is in being able to observe solidification while it is occurring. However, the observations are restricted to the glass-metal surface and may be influenced by this surface. Also, one has no knowledge of the interior of the sample, in contrast to studies of the freezing of transparent organic eutectics.' Observations. The alloy near the eutectic composition (26 at. pct Pb) solidified in a lamellar structure when the growth rate was uniform. If the growth

Jan 1, 1968

By W. C. Ellis, M. E. Fine

INTRODUCTION IN the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;1 the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition which has a large effect on other properties. The thermal expansion data for the system have been reported3,4.5,6 only from room temperature to 100°C, and for this temperature range a minimum in coefficient in the region of 50 at. pct cobalt is well established. 3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the interrelation. EXPERIMENTAL PROCEDURE The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 50 pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 ½ in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for r hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,7 the differential expansion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outer silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested on a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A non-oxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1948

By AIME AIME

ABOUT one hundred were in attendance when Donald M. Liddell opened the session* on non-ferrous metallurgy at 2 p. m. on Tuesday. F. F. Col- cord was vice-chairman. For the first part of the session the chair was turned over to Frank G. Breyer, who introduced G. L. Spencer, Jr., to read his contribution (T.P. 378), "High Silica Retorts at the Rose Lake Smelter," which was an account of the method of manufacture of high-silica zinc retorts at the Rose Lake smelter, and of the service given by these retorts. The materials used are, by volume, 50 per cent clay, 25 per cent silica flour and 25 per cent grog. Written discussion of the paper by E. M. Johnson, W. R. In- galls and M. M. Neale was read by Mr. Breyer. Mr. Johnson explained that their practice in manufacture differed very little from Rose Lake practice, but that their retorts did not last as long, possibly because Eagle-Picher does not use a hydraulic retort press or sintered ore. He ascribes the longer life of silica re- torts to the fact that they do not bend under heat. Mr. Ingalls pointed out that silica retorts are no better as heat conductors than clay retorts, but that they do have a superior rigidity in the furnace. The character of the retorts does not affect the density of the charge. Mr. Neale gave the procedure in the manufacture and use of high-silica retorts at the Donora zinc works, not

Jan 1, 1931

With the coming of the month of 'October the various sections are beginning active work for the winter. The Colorado, Washington, Montana, and New York Sections are all doing good work in raising funds for the hospital bed at Rheims which is to be a memorial to the members of the A. I. M. E. who gave their lives in the great war. We hope that all the other sections will begin to work with this object in view and will make even a better record than they did with the Belgian Relief Fund. It was with much regret that the President, Mrs. James F. Kemp, and the Secretary, Mrs. Sidney J. Jennings, were obliged to forego the pleasure of attending the Chicago meeting in September. They were, however, ably represented by Mrs. Arthur S. Dwight who gave an informal talk after which was formed the Illinois Section, which has our best wishes for all success-" Over the top and the best of luck!"

Jan 11, 1919

By A. J. Boynton

THIS paper is not the result of recent research with regard to any particular feature of iron metallurgy, blast-furnace practice or mechanical engineering. It is rather a series of notes with regard to contemporaneous progress in blast-furnace construction and operation, together with some suggestions as to changes and improvements that seem to be desirable. On April 1, 1930, a committee of the Chicago District Blast Furnace and Coke Association presented to that association a rather ambitious study of blast-furnace equipment, together with recommendations for the design of construction of a complete blast-furnace unit for the production of 1000 tons of pig iron per day. This report represented the result of months of study by members of the committee, all of whom were actively engaged in operation or design of blast-furnace plants. It is natural, therefore, that comments on the present state of the art should take this 1000-tons furnace, as recommended by the Association, as a basis for comparison with corresponding features of construction or design. See Table 1. In looking through this report at the present time, the significant difference is in the nature of the gas-washing equipment that today would be specified. In other respects, the installation would remain generally very much as it was outlined in 1930. The change in furnace dimensions would be very slight and of no especial significance, except with respect to changes in stock-line diameter, of which more will be said hereafter. The high-efficiency stove as developed by various designers is thoroughly described within this report, and few changes have taken place since. Blowing equipment shows refinement and reflects the improvement in steam engineering. Hoisting and charging equipment and ladles for the conveyance of iron and slag remain, in general, as they were in 1930. In accordance with a general tendency

Jan 1, 1935

By T. Watanabe, S. Karashima, H. Oikawa

Creep tests of a! iron and its solid-solution Fe-Mo, Fe-Co, and Fe-Si alloys with bcc structure were conducted under constant stresses in ferromagnetic and paramagnetic temperature regions above 0.5T,(T, is the absolute melting temperature). It was found their high-temperature creep behavior changed in the vicinity of the magnetic transformation temperature, that is Curie temperature, TC. In the ferromagnetic region below the steady-state creep rates were lower than those expected from the extrapolation of the data in the paramagnetic region, the amount of decrease being affected by solute addition. Also, activation energies for steady-state creep were different in the two temperature regions. The observed changes were concluded to be due to the effect of ferromagnetism on diffusion. It is well-known that plastic deformation of metals and alloys in the temperature region where mobility of atoms becomes high enough is controlled by atomic diffusion." Many experimental results394 on fcc and hcp materials have been reported to confirm this view. In bcc metals and alloys, not much basic investigation of creep deformation has been performed. In particular, experimental work on iron5-&apos; and its alloys, covering a quite wide temperature range is extremely scarce. On the other hand, the effect of ferromagnetism on diffusion has recently been demonstrated in a iron and its alloys;&apos; it has been made clear that diffusion rates in ferromagnetic temperatur~e region are significantly lower than those expected from diffusion measurement in the paramagnetic region. Therefore, it is concluded that the magnetic effect influences the high-temperature creep behavior in a! iron and in its alloys. The present authors have conducted creep experiments on a iron and its solid-solution alloys over a very wide temperature range, and have demonstrated the magnetic effect. A part of the result has already been reported elsewhere.26 In this paper, the experimental results will be described in detail. While the manuscript was in preparation, a similar magnetic effect on creep deformation of a iron was reported by Ishida . Though their experiments covered an extremely wide temperature range, the creep stresses varied from several thousand psi to several ten thousand psi with decreasing temperature. Consequently, it may be said that there remain some questions concerning their results. I) EXPERIMENTAL PROCEDURE The materials used in the experiments were pure iron and its alloys; they were prepared by vacuum melting (10"" mm Hg) electrolytic iron (99.9 pct), molybdenum powder (99.9 pct), ultrapure silicon, and cobalt pellet (99.5 pct) in alumina crucibles. The ingots were hot-forged to plates 10 mm thick and 50 mm wide, and then were hot-rolled at about 700°C into sheets 1 mm thick. Creep specimens, 5 mm in width and 15 mm in gage length, were machined from the sheets. They were annealed at temperatures which were well above their respective recrystallization temperatures. The chemical compositions of the metal and alloys are shown in Table I together with their heat treatments. High-temperature creep tests by the use of a lever-type creep testing machine were carried out in argon atmosphere under constant tensile stress. In order to keep &eep stress constant within about *0.5 pct, stress change due to specimen elongation was compensated by tensile force of a stainless-steel bellows which was inserted between the loading lever and lower specimen grip with the assumptions of a linear relationship between change in cross section and strain and uniform strain along the section. Beyond the limit of compensation by the bellows, small amounts of load were removed after appropriate strains. The testing temperatures were maintained to within i2"C of the reported values. Creep deformation was auto-graphically recorded at the upper (moving) specimen grip using a linear differential transformer which was held by a stainless-steel rod mechanically connected to the lower specimen grip. It was also directly measured with a dial-gage reading to -& mm. 11) EXPERIMENTAL RESULTS AND DISCUSSION 1) Creep Curves of a Iron and Its Alloys. Creep curves of a! iron, Fe-Si, Fe-Co, and Fe-Mo (<2 at. pct Mo) alloys usually consisted of three stages, that is transient (primary), steady-state (secondary), and accelerating (tertiary) stages. An example is illustrated in Fig. 1 for a! iron. However, in Fe-Mo alloys with more than 2 at. pct Mo, an inverse transient creepZ8 was observed as indicated in Fig. 2. The inverse behavior, which varied with the amount of molybdenum, may be due to the substructure* in the annealed specimen as was sug-

Jan 1, 1969

By H. O. Hofman

With the exception of the exhaustive paper on the Father de Smet mill, by its designer, Mr. A. J. Bowie, Jr. (Bans., x. 87), nothing, so far as the writer is aware, has as yet appeared on the stamp-mills of the Black Hills of Dakota, although they have been steady producers for the last ten years. Within the small area of about 6000 by 1600 feet, $2,271,341.14 was produced in 1887† from rock averaging $4 per ton in free gold. I. The Ores. Character of the Ores.—The gold of the district is found in quartz and pyrites finely distributed through vast bodies of mica- and amphibole-schists, argillites and phyllites, and also impregnating the schists themselves. The " Belt," embracing the section of Lead City, Terraville and Central City, is the only part worked at present. The principal associated mineral is iron pyrites, with some arsenopyrite and chalcopyrite, garnet and asbestos. The ores from open cuts and upper levels are more free-milling. than those from underground workings below water-line. Hence

Jan 1, 1889

By Walter W. Bradley

AT ONE TIME OR ANOTHER and in greater or less amounts, gold has been mined in at least 40 of California&apos;s 58 counties. It may not be inappropriate, by way of introduction, to give a brief historical statement relative to her production of the yellow metal. The presence of gold in the gravels of San Gabriel, San Francisquito, and other streams near Los Angeles, was known and they were worked in a small way by the Indians, at least as early as. 1841&apos; and possibly 1820. -On March 2, 1844, Don Manuel Castanares, deputy for California to the Congress of Mexico, reported&apos; to his government that placers near Los Angeles had yielded up to December, 1.843, a total of 2000 oz. of gold dust, most of which had been sent (via Mexico) to tile United States Mint at Philadelphia.

Jan 1, 1932

By G. E. Frantti

UNDER the auspices of the Geophysical Committee of Michigan College of Mining and Technology, an investigation was made in Michigan&apos;s Upper Peninsula to obtain geophysical data" related to the regional subsurface geology in the area covered by Paleozoic sediments. The area surveyed includes that portion of the Upper Peninsula which lies between R18W to R26W and T41N and T49N, covering approximately 1300 square miles. On the index map, Fig. 1, it is represented by the cross-hatched zone west of Munising. Four of the five sites of detailed investigation are indicated by the letters A, B, C, and D. A detailed gravity and magnetic survey had previously been conducted by J. G. Wilsonz near Perkins, 8 miles north of Rapid River, on a local anomalous area. Results of his work, which showed a large positive magnetic anomaly associated with a gravity anomaly, aroused interest in the possible economic significance of the formations underlying the Paleozoic sediments in this part of the Upper Peninsula. Early in the 1900&apos;s the Michigan Geological Survey, as well as many private companies, had done a considerable amount of dip needle work near the southwest corner of the area discussed in this paper. Most of the information available to the writer was obtained from indicated magnetic anomalies on the geological map of the northern peninsula of Michigan. Results of the geophysical activities of mining companies in the vicinity of the Marquette range and Gwinn district were unavailable to the author. Physiography and Geography: The region under consideration has low to moderate relief. About half the area is comprised of swampy lowlands, and because of the swamps and forests much of the land is almost inaccessible. The major drainage system is dendritic, with streams flowing into Lake Michigan on the south and Lake Superior on the north. The general geology, shown in Fig. 2, indicates an overlay of Paleozoic sediments on pre-Cambrian formations along a line running approximately south from Marquette (not shown on the geological map). Actual contact between pre-Cambrian and Paleozoic sediments is not known because most of the area is covered with glacial till, and outcrops are very scarce. Exposures of the Paleozoic sediments show that these beds in the northern areas dip gently under Lake Superior and that in the southern areas they &apos;dip gently to the southeast. Outcroppings of the pre-Cambrian formations occur primarily to the west of the surveyed area except in the northwest corner where the Laurentian series outcrop as far east as the Gwinn district and also in T46N, R24W. Instrumentation: Gravity measurements were made with the Worden portable gravity meter. Since this was chiefly a reconnaissance regional survey, both the large and small dials were used. The instrument used had a constant of 0.0035 milligals per scale division, a working range of about 25 milligals.

Jan 1, 1957

By William Gilman

IN the past five years, and without much fanfare, Turkey has emerged as a significant figure in the world mining picture. This has been accomplished by a five-year plan now in its last year. A second five-year plan is already under way, ahead of schedule. It will concentrate even more than the first in developing Turkish mines in order to increase present exports of coal, chrome ore, and copper, and to develop new mineral exports as well. To be fully understand the republicic?s mining program should be considered as something more than merely tapping rich resources in the East along the Aegean Sea, in the North among the mountains descending to the Black Sea, and in the West at the foot of the Taurus Mountains. It should also be viewed in the light of a strong nationalist policy with many aspects of state socialism. Turkey declares frankly that all mineral re- sources belong to the nation and all exploitation should be by the state for the twin purpose of modernizing the state and securing foreign exchange for the state by exports. Accordingly, the principal mines are state-operated and a few lesser enterprises, although not state-owned, have at least been put in the hands of Turkish capital.

Jan 1, 1938

By Arthur Forsyth

A SEARCH through the available literature shows that the cobalt-nickel-silicon system has not been systematically studied. This seems rather odd because all three elements are fairly abundant and have better than average corrosion resistance; however, they have high melting points, which makes experimental work difficult. Cobalt and nickel form a continuous series of solid solutions and each metal dissolves about 7.5 per cent silicon. Many ternary alloys have been studied and the results have been published in a great many different ways, but to present such data in a short but clear and understandable manner is still a problem. The following pages describe the results of the study of 76 alloys from which the partial ternary diagram (Fig. 1) of the cobalt-nickel-silicon system has been drawn. The alloys were chosen according to the plan in Fig. la by taking definite ratios of cobalt and nickel, such as 70 Ni, 30 Co or 40 Ni, 60 Co, and adding silicon in various percentages. Each section was studied in detail by means of thermal analysis and microscopic examination, but only two of these detailed sections were thought necessary in the point perspective drawing to give a comprehensive picture of the liquidus, solidus and solid transformations that take place over the temperature ranges studied. Complete thermal analyses and microscopic data are given in Table 1.

Jan 1, 1940

By Richard L. Stowe, Donnie L. Ainsworth

The static, rapid, and shock-loading response of rock is of interest to many in the field of rock mechanics. For example, the effects of loading rates on strength and stress-strain characteristics of rock are quite important in defining input loading for use in the design of underground protective installations. Response data on rock subjected to shock loading over a wide range of pressures are also vital in the field of underground nuclear testing. In addition, material response is needed in design of shock-absorbing liners. A number of investigators have reported that ultimate compressive strength of rock increases with increased rates of loading.1-6 Wuerker3 stated that modulus of elasticity, obtained from sonic determinations, increased in some rocks by a factor as high as 4.5. It appears that only a limited amount of work has been done on comparing static modulus and modulus obtained from impact testing.6 Phillips4 showed that with increased rates of loading the deformation decreased. More recent work by Atchley and Furr5 showed that when moderate-strength concrete is stressed with increased loading rates, the axial strain at failure increased. One would expect this to occur if we think in terms of purely elastic materials. For example, if E is constant and maximum strength [amax], increases, the axial strain would also increase. However, in rock testing thus far we have worked almost exclusively with nonhomogeneous and inelastic rocks. From this fact alone the increase in axial strain with increased load application is noteworthy.

Jan 1, 1972

By H. H. Johnson, Eric W. Johnson

A newly developed ac technique was used to measure the electrical-resistivity changes associated with both cyclic stressing and subsequent annealing of high-purity and OFHC copper. The early stage of push-pull fatigue was explored at 293° and 4.2°K, with stresses chosen for an expected fatigue life of 2 to 8 X 105 cycles. For high-purity copper, fatigue at 293°K was accompanied by an initial increase in resistivity. After about 5000 stress cycles, no further increase was observed. Annealing studies showed that the resisticity increment could be accounted for solely in terms of an increased dislocation density, to about 2 x 1010 disl pev sq cm. Fov 42°K fatigue, however, the resistivity increased continually, with no evidence of saturation, as approximately (No. of stress cycles)1/4. This is intevpreted to result from both dislocation multiplication and vacancy production; estimated vacancy concentrations are 10-4 to 10-9. The continuous resistivity increase was inhibited by interspersed annealing treatments at 293°K, which also raised the level of the stress-strain curve. These effects are attributed to annealing of vacancies into dislocation loops. In contrast, OFHC copper fatigued at 4.2°K showed saturation of electrical vesistivity after only a few hundred cycles, and it appeared that vacancies annealed out completely between 77° and 293°K. MaNY observations suggest that both dislocation multiplication and point-defect production are important aspects of fatigue deformation. An increase in dislocation density with number of stress cycles has been demonstrated or implied by several experimental techniques, including optical metallography with lithium fluoride,&apos; electron microscopy with copper,2 thermal conductivity of Cu-Zn alloys,3 and peak-stress measurements during cycling at constant plastic strain amplitude.4,5 At low amplitudes and/or stresses saturation of fatigue hardening and dislocation density occurs early in the expected fatigue life,4-6 frequently by a few hundred cycles. The evidence for point-defect production is somewhat less extensive, but it is nonetheless persuasive. Rosenberg7 reported briefly that, for equal stresses, copper fatigued at liquid-hydrogen temperature displays an increase in electrical resistance some ten times that which accompanies unidirectional stressing. Further, the extra resistance saturates after a few hundred stress cycles, and does not anneal significantly until a temperature of about 170°K is attained.&apos; Point-defect production during fatigue is also suggested by 1) the softening during cyclic stressing of initially strain-hardened polycrystal-line copper9, 2) the strong temperature dependence of the yield strength of fatigue-hardened mono- and polycrystalline copper,579"0 and 3) the influence of intermediate annealing upon slip-band formation in copper fatigued at 90°K.8 It is evident that characterization of the fatigued state requires a knowledge of both point-defect and dislocation densities. For this purpose electrical-resistivity measurements are useful, but they are difficult to perform because of geometric limitations. Push-pull fatigue is necessary to obtain a macroscopic ally uniform deformation over the specimen cross section; however, the specimen must then have a low slenderness ratio to avoid plastic buckling, while the standard dc resistivity technique requires a very slender specimen for

Jan 1, 1965

By S. J. Swainson

PHOSPHATE ROCK is a low- priced commodity. This fact has influenced the choice of mining and beneficiating methods to a greater degree, perhaps, than in most other low-grade mining operations. The fact that many yards of everburden and matrix must be stripped and mined per ton of salable "rock" produced and sold has necessitated he development of relatively simple btneficiating plants having high capacity and low capital and operating costs. The law of diminishing returns must always be reckoned with in phosphate mining and washing, and often recovery must be sacrificed in favor of costs in order to achieve the highest over-all economic efficiency. The phosphate-bearing formation, known as "matrix," is composed of (1) phosphate pebbles, which are somewhat rounded in shape and which vary in size from 1-in, to micron sizes, (2) rounded quartz grains usually smaller than 10 mesh, and (3) clay, of varying "stiffness," which is the binder of the matrix. The phosphate pebbles vary in hardness. Their color, which varies from white to black, is not a reliable indicator of the Bone Phosphate of Lime (B.P.L.) content of the

Jan 1, 1944

By J. F. Smith

ELASTIC constants of yttrium and eleven of the rare earth elements have been measured. This has been accomplished by measuring the propagation velocities of ultrasonic pulses. The velocity measurements were made by noting the elapsed time between an applied pulse and the appearance of successive echoes. The pulse-echo technique has become relatively common, and the basis of the measurement is outlined in several standard tests, e.g., Heuter and Bolt.1 Two important assumptions are made when using this method for the determination of elastic moduli. First, the pulse is assumed to propagate as a plane wave. To justify this assumption, the cross section of the test specimen should be large compared to the wave length of the transmitted pulse. For these measurements on the rare earth elements the minimum cross section wave length ratio was about 20. A second assumption which must be made when using polycrystalline specimens is that the grains are sufficiently numerous and randomly oriented so that the specimen may be approximated as elasti-cally isotopic. The grain size in the as-cast specimens which were used is believed to be sufficiently fine for this approximation, and the degree of preferred orientation is believed to be small. Supporting this viewpoint is the fact that elasticity measurements by the pulse-echo technique on as-cast specimens of other metals give results which are in satisfactory agreement with values obtained by other techniques. Hence, it is believed that the measured elasticity values for the rare earth elements are not apt to be seriously in error due to the assumption of elastic isotopy. The apparatus used in this determination was a modified Sperry Reflectoscope with a precisely calibrated time base circuit. Piezoelectric transducers were used both to generate the pulse and to detect the echoes. X-cut quartz crystals were used for the longitudinal modes, and Y-cut quartz crystals were used for the shear modes. Frequencies of 2.25 and 5 megacycles per sec were employed. Most of the specimens were 2.5 to 5.0 cm in length. Results Table I is a tabulation of the measured propagation velocities of longitudinal waves and of shear waves, together with densities obtained by Sped- ding, Daane, and Herrmann2 from lattice parameter measurements. The shear modulus, Poisson&apos;s ratio, and Young&apos;s modulus were calculated from the data in Table I through use of the following relationships: µ = pv32 [1] s=2-(vb/vs)2/2[1-(vb/vs)2] [2] and Y= 2µ(l+s) [3] where s is the shear modulus, Y is the Young&apos;s modulus, s is Poisson&apos;s ratio, p is the density, V0 is the longitudinal wave velocity, and v, is the shear wave velocity. The calculated quantities are shown in Table 11. Compressibility values can be computed from the relationship and the computed values may be compared with measured values obtained by Bridgman.8 Table III lists the data for such a comparison. The agreement is satisfactory, being particularly good for neodymi- um and gadolinium, poor for samarium, and intermediate for the other elements. Some variation is expected since Bridgman&apos;s measurements are isothermal, whereas the present measurements are adiabatic. In addition there may be some effect due to small variations in purity. Though most of the rare earth metals measured by Bridgman and all of the metals used in the present measurements were prepared at this laboratory, minor purity variations might exist since the samples came from different lots. Also, any imperfections such as dislocations, vacancies, voids, grain boundaries, microcracks, etc., should contribute to the volume change of a com-

Jan 1, 1958