Search Documents

By W. F. Wheeler

IN the study of the coals of Illinois now being carried on by the State Geological Survey, an attempt is being made to determine the most satisfactory basis of comparison between different coals. The following discussion is based upon work done for the survey in the laboratories of the State University and under the general direction of Prof. S. W. Parr. " Pure coal " has been defined by Mr. A. Bement1 as ash- and moisture-free coal, and the use of this " pure coal " as a basis for comparing different bituminous coals has lately been much discussed among engineers in the middle West. By some the B.t.u. of the pure coal is being used to check calorimetric results, and to calculate the calorific value of different coal-samples from the same seam, for which purposes it is necessary to assume-first, that the composition and calorific value of pure coal from different parts of the same coal-seam are uniform, and, second, that these values remain constant after the coal is mined, both of which assumptions there are reasons to believe are inconsistent with the facts. Certain variables are included in pure coal, as ordinarily defined, and disregard of them may lead to serious error. In any event, where delicate shades of difference are involved, no sure interpretation of results can be made, unless these variables be eliminated. As a basis of comparison between coals, ash- and moisture-free coal is much to be preferred to " dry coal," and still more is it to be preferred to " moist coal," as ordinarily reported in analyses. There are, however, two constituents other than ash and moisture which are similar in effect to them, and which

Jan 1, 1908

By W. H. Emmons

MOST mineral deposits change as they are followed downward on their dips. Some of these changes are due to primary arrangement; different ores were precipitated at different depths when the deposits were formed. Other changes are due to weathering or secondary enrichment. The chief changes resulting from weathering, in the main, are understood and standard changes are recognized. The processes are relatively simple. They take place at ordinary temperatures and pressures and can be duplicated in the laboratories. Moreover, there are thousands of deposits available for study, because the processes take place near the surface where the development of mines is begun. The changes due to primary arrangement of the deposits of the metals are not so well understood. Deposition has taken place at higher temperatures and our knowledge of the chemistry of the processes leaves much to be desired. Very few experimental data are available. The deposits, moreover, offer fewer examples because many mines are not, developed to depths where the changes can be studied and a change to unprofitable material usually results in stopping work. Most, students of ore deposits now accept, as confirmed, the hypothesis that nearly all lodes and related deposits were formed by solutions originating in intrusive igneous masses. Outward from these masses, the deposits at many places are grouped in zones and the arrangement noted from the intrusions outward are commonly the reverse of the changes noted from the surface downward in a single lode. A study of the changes in groups of deposits, from the parent intrusion outward, will throw light on the changes to be expected in a single lode downward. Because the changes in series of deposits from the intrusive outward may all be observed near the surface, where more data are available, it is possible to increase the number of examples many fold and to apply the statistical method of study with greater confidence of avoiding error.

Jan 3, 1924

By R. M. Rose, D. P. Ferriss, J. Wulff

Single crystals of tantalum, tungsten, and the binary alloys thereof were grown by electron-beam zone melting and tested in tension between 77° and 373°K. The ductile-to-brittle transition temperature increased sharply with solute concentration, for both tungsten-rich and tantalum-rich alloys; apparently, the maximum transition temperature exists near the 50 pet concentration. Twinning was observed to be a consequence of cleavage-crack propagation. Cleavage occurred on(100)planes, and extensive tearing and "river markings" were present. The onset of brittleness could not be associated with any change in deformation mode, the yield point phenomenon, or the large rise in yield stress with decreasing temperature. Cleavage was observed to initiate at either the specimen surface, or subgrain boundaries. The observation was made that the grain boundaries of Polycrystalline materials are probably even better as nucleation sites for fracture, and are responsible for brittleness at high temperatures and lower solute concentrations than those of the corresponding single crystals. TUNGSTEN and tantalum, the two high-melting neighbors in the third transition period of the periodic table, present striking contrasts. Although both are bee, tungsten has far higher elastic moduli, and the highest ductile-to-brittle transition (DBT) of all the pure metals.' Tantalum, however, is ductile at liquid helium temperatures. Large strain aging and yield point phenomena are observed in tantalum,2,3 but only to a lesser extent in tungsten.4 Tungsten work-hardens at a high rate,5 whereas this effect is negligible in tantalum.' Since the mutual solid solubility of these two metals is complete,7 and no ordering has yet been reported in the binary system, the possibility of depressing tungsten's DBT by tantalum additions was considered. Also, tungsten additions to tantalum could produce hard, high-melting alloys which might be ductile at room temperature. Such alloys offered excellent bases for complex alloy development, particularly with regard to the effect of rhenium on Group VI metals.8"10 In addition, there was the opportunity to examine flow and fracture modes in the vicinity of the DBT, with particular emphasis on the correlation between brittleness and fundamental deformation mechanisms. Myers11 has reported that recrystallized alloys with up to 10 pet W in tantalum are ductile at room temperature, but alloys with 20 pct W could not be swaged at temperatures as high as 500°C. The whole spectrum of Ta-W alloys has been surveyed by Braun, Sedlatschek, and Kiefferl2 using sintered powder compacts. In addition to some physical properties they reported a maximum hardness at about 50 at. pet W, dropping to much lower hardness levels for the pure components. They were able to cold work tantalum-base alloys with as much as 30 pet W and to warm work tungsten-base alloys with up to 20 pet Ta by procedures similar to those used for pure tungsten. EXPERIMENTAL In order to study deformation modes and to keep the impurity concentrations at a minimum, electron-beam zone melting was used to prepare single crystals of high purity. The electron-beam zone melting apparatus is similar to that described by Calverley, Davis, and ever" and incorporates a grid control rectifier to maintain control of emission current. Pure metals were refined by making three zone passes at 4 mm per min up the rod. Alloys were prepared by melting together wire of one constituent on a previously melted rod of the major constituent. Subsequently, two zone passes were made in opposite directions to level the composition after the manner suggested by pfann.14 Purification of the starting materials was accomplished by evaporation of the several impurities, and the degree to which this was accomplished is indicated in the chemical analyses of Table I. The uniformity of composition along a zone levelled rod was within the i 1 pet accuracy of the fluorescent X-ray technique used to determine composition. Crystallographic orientation of the

Jan 1, 1962

By James Aston

THREE years ago the writer presented a paper on the trend of development in the wrought iron industry,1 wherein was described a process in the development of which he has been a factor, which at that time had passed through several years of progressive experimental development but which had not then been put upon a commercial scale of operation. The present paper deals with two years of observation and experience in the commercial operation of a plant by the A. A Byers Co. at Warren, Ohio. It will not enter into the controversial field of the relative merit of wrought iron and steel in various classes of service, nor will it elaborate upon the characteristic services or fields of utility to which wrought iron is particularly adapted. It is sufficient to state that the wrought iron industry is upon a substantial basis and that the material finds service in pipe, where its advantages are in superior corrosion, fatigue, welding and threading qualities; in bar iron for staybolts, engine bolts, and rivets, demanding maximum service against corrosion and fatigue; in plates for corrosion service; and in chains, because of welding and shock-resisting characteristics. In short, ability to withstand the stresses of shock and vibration, or the ravages of corrosion, to hold protective coatings, and to give maximum efficiency in welding, are its features of relative superiority. If these features were not well recognized, the wrought iron industry would have shrunk to insignificance in the face of high costs and acknowledged limitations in manufacture. To charge that this industry is built upon a structure of assumption, psychology, and improperly weighed evidence is an impeachment of the integrity or belittling of the powers of observation of users through many centuries of service experiences.

Jan 1, 1929

By Jacob T. Wainwright

AS a means for increasing the efficiency in modern blast-furnaces by supplying to them blast of a much higher temperature than is now possible, the writer offers as a suggestion a modification in the construction of regenerative hot-blast stoves. Stated briefly, the plan proposed is to pre-heat both the gas and the air for its combustion in a manner similar to that generally adopted in Siemens openhearth furnaces. After thus carrying the temperature of the stove to a point much higher than that common in hot-hlast stoves, the cold blast passes through it. Without entering into the details relating to the reversing valves and the system of flues, the general plan may be outlined as follows, referring to the accompanying drawings: The valves are so placed in heating up the stove that the blast-furnace gas enters at B, Fig. 1, and the cold air for combustion at A. Ascending in flues, F and E, respectively, combustible gas and air meet and mix in the combustion-chamber, I. Flowing through K, they descend through the flues, G and H, escaping through the chimney. In this manner the walls of the combustion. chambers, I and L, are highly heated, and the right-hand side of the stove is carried to a higher temperature. By reversing the valves, blast-furnace gas enters at C and cold air for combustion at D. Both are pre-heated in their ascent through the flues, G and H. They burn in the combustion-chamber, L, and the hot gases of combustion, flowing through K, I, E and F to A and B, heat the left-hand side of the stove. In this manner the stove is carried to a temperature greater than that of those now generally in use, in which air and gas are burned without preliminary pre-heating. In the plan proposed, that side of the stove will, of course, be relatively cooler through which cold air and furnace-gas last passed in its ascent to its combustion-chamber. After having sufficiently heated the stove in the manner outlined, the cold blast is admitted through all the flues, A, B, C and D. It ascends through the highly-heated regenerative material to the chambers at the top and descends through the flue, P, Fig. 2 (dotted

Jan 1, 1889

Discussion * of the paper of H. M. Chance, presented at the butte meeting, august, 1913, and printed in bulletin No. 79, July, 1913, pp. 1315 to 1341. George H. Ashley,+ Washington, d. C.:-Mr. Chance's long practical experience in reporting on coal lands admirably fits him for a discussion of the value of such lands. On behalf of the government geologists, I wish to express my appreciation of Mr. Chance's friendly, constructive criticism of the government method of valuing coal land in the first part of his paper and, at the same time, to reply to some queries he makes. All admit that coal has no " intrinsic "-monetary value, in the sense that a pound of coal of certain chemical and physical characters is worth " intrinsically " so many cents or fractions of a cent. The term has, however, been found very useful as including those natural factors of coal value, among which are its position and location in the earth, that affect its sale price in contrast with the other cost elements involved in the labor and capital necessary in mining, preparing, transporting, and selling the coal (extrinsic factors). Mr. Chance, while recognizing the " dual origin of value," does not offer any better terms. The survey agrees with Mr. Chance in his definition of coal conservation, that it means the fuller utilization of the heat contents of the coal, and the more complete recovery of the coal from the ground. Coal land withdrawals have not been made to keep such lands off the market, but to prevent their acquisition as non-coal lands before they could be classified so as to be disposed of under the proper law. Nor has the pricing of the more valuable coal lands above the minimum been to raise money for the reclamation fund, to which the money goes, but primarily to discourage the alienation, for holding or speculation, of coal lands not intended or needed for development, and, secondarily, to secure to the people the ?unearned increment," which they are certain in any case to be charged.

Jan 11, 1913

By Cornelius Kelley

THE American producers of silver are keenly alive to the importance of the silver problem and its vital effect on the mining industry in Montana and other States where precious-metal mining constitutes a basic industry. There are so many ramifications to the subject that one is tempted, no matter from what angle an approach is made, to digress along lines that inevitably lead into a maze of social, economic and financial problems, through which no clear pathway is marked, and regard¬ing which no definite opinion can be expressed, as the ultimate solution is dependent upon the policies adopted and carried out by the more important Governments with reference to their fiscal requirements and currency systems. The situation may be summarized in two questions First, what, if any, plan have the silver producers, as being the most directly interested, to offer in meeting the situation which will confront the industry upon the termination of purchases of domestic silver under the Pittman Act? Second, what, if any, assistance can be extended by the Government in connection with the problem? In answer to the first inquiry, while the matter has been the subject of discussion among the principal producers, they have been unable to formulate a defi-nite plan, principally because they have been and are dealing with a subject embracing many unknown fac-tors; and second, it has been felt that before any plan is adopted there should be indicated the extent to which cooperation on the part of the Government may be depended upon to enable a proper study of the situation to be made. In order to explain these rather cryptic statements, a general review of the situation may aid. Whatever differences of opinion there may have been in the past upon the subject of bi-metallism or the establishment of a fixed ratio between the coinage value of gold and silver, it will probably be conceded that it would be neither wise nor expedient to attempt a revival of this discussion, nor to undertake to solve the question by the adoption of such a remedy. Issues of contro-versial economics must be avoided, if possible-political economics will destroy rather than assist constructive effort.

Jan 2, 1923

By Nelson Severinghaus

FOLLOWING the end of hostilities of World War II, a resurgence of industrial and home building has given impetus to the use of many products of the stone industry. Shortage and high prices of some building materials such as lumber have aided wider acceptance of materials such as concrete products which have been relatively plentiful and which have not risen so rapidly in price. Ingredients for many of these substituting materials come from the stone industries, often from by-products of stone operations. Most of the tonnage of the stone industry in the State of Georgia comes from granite and marble. There are extensive dimension stone operations in granite in the Elberton and in the Lithonia areas. Building and monumental marble from the Tate area has been used throughout the country. Cutting operations in both types of stone have their by-products in faulty blocks and in spalls. In the State there are three large crushed-stone plants utilizing granite, one near Camak, one near Lithonia and one at Stockbridge. All have had excess fines or screenings in the past but this excess is largely disappearing with development of new uses. At times this "waste" has amounted to as much as 20 pct of the stone quarried. Handling of this large tonnage from point of screening out to storage piles presented a costly problem and large areas were taken up by the piles. Crushed stone is generally sold with a relatively narrow margin of price over cost, so any elimination of disposal cost or increase of income by marketing of by-products is highly desirable. BY-PRODUCTS OF GRANITE DIMENSION STONE It sometimes becomes difficult to differentiate between main product and by-product. In the cutting of granite dimension stone in the Lithonia district of Georgia, a considerable quantity of remnants of uneven shape and size is produced. The larger of these pieces have long found use as building rubble, particularly for retaining walls and building foundations (Fig I). They are broken down to one man size by plug drilling and wedging and by hammer. In recent times, demand for this former by-product has grown so that quarries have been opened for the production of rubble as a main product. Local masons have attained skill in using these irregular shapes to form economical and attractive walls. Areas such as Elberton, Georgia, which do not have a large building market nearby, tend to accumulate piles of large pieces of reject stone. When a road job or other local construction offers a quantity market for crushed stone, a portable crusher works this material down to crushed aggregate. Spalls and finer chips from granite stone-cutting operations have generally found their way into crushers and thence to the many uses for crushed aggregate. One company near Lithonia started marketing the smaller by-product crushed sizes for chicken grit about ten years ago. This use has grown to nation-wide distribution and the tonnage is now so great that they have opened a large quarry with

Jan 1, 1947

By L. R. Weisberg, E. A. Miller

Single-crystalline films of silicon of good quality were vacuum-deposited on sapphire. The improved crystallinity was achieved by the strict exclusion of oxygen from the evaporation system, including the use of a "oxygen-free" silicon source. To minimize possible contamination of the source, the silicon was sublimed from the solid at about 1390° C. using a simple electron bombardment system to heat the silicon. This resulted in deposition rates of about 5 to 7 µ per hr and film thicknesses of 4 to 20 µ. The vacuum during deposition was ordinarily about 5x 10-8 Torr, DESPITE the success achieved in the chemical vapor deposition of silicon on sapphire using Silane,1-4 vacuum deposition has not provided comparable properties. For example, Chu et a1.5 vacuum-deposited silicon on single-crystalline substrates of A12O3, Sic, ThO2, and other compounds, and, although some epi- but the use of ultrahigh vacuum (about 1 to 3 x10-9 Torr) during deposition did not significantly improve the results in the oxygen-free system. The crystalline quality of films deposited on (0001) sapphire was found to be considerably superior to (1102) sapphire surfaces. Using (0001) sapphire, single-crystalline films were deposited at temperatures as low as 780° C and as high as 1075°C, with the best crystalline quality obtained at about 1000°C. At this temperature, hole mobilities over 250 sq cm per v-sec were achieved. taxy was indicated, single-crystalline films were not produced. More recently, Salama, Tucker, and young6 evaporated silicon on single-crystalline sapphire, but only poor crystallinity was observed, and low carrier mobilities were measured. In the present experiments, good-quality single-crystalline films of silicon on sapphire have been achieved by specifically excluding oxygen from the evaporation. This included not only the use of a "clean" vacuum system but, of special importance, the use of an oxygen-free silicon source. This has also been shown to provide a dramatic improvement in silicon homoepi-taxy.7 As a result, silicon-on-sapphire films with hole mobilities over 250 sq cm per v-set were achieved, and single-crystal films were grown as low as 780°C and as

Jan 1, 1969

We the undersigned, being all persons of full age and citizens of the United States and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 5 of Article I. of said law, the existing unincorporated association known as American Institute of Mining and Metallurgical Engineers, Incorporated, do hereby make, acknowledge and file this Certificate for that purpose, and do Certify as follows: I. That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences, connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained. II. That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council; that the undersigned are all members of said Council as the same was constituted on the 29th day of December, 1904. III. That on said last-mentioned date a regularly called meeting of said association was held at its office in the Borough of Manhattan, City of New York; that thirty days before such meeting notice of the intention to incorporate said association was given by mail to each member thereof whose residence or post-office address is known; that at said meeting the following resolutions were offered, seconded and duly adopted by the unanimous vote of all its members then present, to wit: "Resolved, That it is the sense of the members and associates of the American Institute of Mining Engineers in general meeting assembled that it is desirable and necessary for the well being of said association and its members and for the furtherance of the objects for which the same has been formed, that said association incorporate under the Membership Corporations Law of the State of New York; "And Further Resolved, That the Members of the Council of this Association, or a majority thereof, be and they hereby are authorized, in accordance with the provisions of Section 5 of Article I. of the Membership Corporations Law, to incorporate this association for the same purposes for which it has been organized and conducted, in the manner provided in Article II. of said law;, "And Further Resolved, That the name of said corporation as hereby adopted by this meeting shall be American Institute of Mining Engineers; "And Further Resolved, That the said incorporators shall be named in the Certifi¬cate of Incorporation as directors of such corporation until its first annual meeting,

Jan 1, 1940

By D. Hartley

United States Steel Corp's. Minntac mine is located at Mt. Iron, Minn. on the Mesabi Iron range. The taconite pit is two miles wide, with a maximum depth of 170 ft. Millions of tons of crude ore, waste rock, and surface overburden are handled annually at the mine. All crude ore plus some of the lower-grade rock are rail-hauled; other materials are trucked. Length of rail haul averages 3.5 mi, with a lift of 140 ft. The maximum grade against the load is 1 ½ %. Nine 1200 hp diesel-electric locomotives handle trains of 40-and 50-cu yd side dump cars in crude ore and lower-grade rock service. In addition to this continuous operation, locomotives handle coarse tailings disposal and switching duties on an intermittent basis. All railroad equipment operates under the supervision of a mine control foreman through voice radio communication. The pit foreman also has this frequency available, quickly accommodating any changes in operation that may be required.

Jan 1, 1970

By W. H. Emmons

Most mineral deposits change as they are followed downward on their dips. Some of these changes are due to primary arrangement; different ores were precipitated at different depths when the deposits were formed. Other changes are due to weathering or secondary enrichment. The chief changes resulting from weathering, in the main, are understood and standard changes are recognized. The processes are relatively simple. They take place at ordinary temperatures and pressures and can be duplicated in the laboratories. Moreover, there are thousands of deposits available for study, because the processes take place near the surface where the development of mines is begun. The changes due to primary arrangement of the deposits of the metals are not so well understood. Deposition has taken place at higher temperatures and our knowledge of the chemistry of the processes leaves much to he desired. Very few experimental data are available. The deposits, moreover, offer fewer examples because many mines are not developed to depths where the changes can be studied and a change to unprofitable material usually results in stopping work. Most students of ore deposits now accept, as confirmed, the hypothesis that nearly all lodes and related deposits were formed by solutions originating in intrusive igneous masses. Outward from these masses, the deposits at many places are grouped in zones and the arrangement noted from the intrusions outward are commonly the reverse of the changes noted from the surface downward in a single lode. A study of the changes in groups of deposits, from the parent intrusion outward, will throw light on the changes to be expected in a single lode downward. Recause the changes in series of deposits from the intrusive outward may all be observed near the surface, where more data are available, it is possible to increase the number of examples many fold and to apply the statisttical method of study with greater confidence of avoiding error. It is not everywhere possible to identify the parent igneous body to which a group of ore deposits are related. Several kinds of criteria are available; certain groups are superior to others. By applying the

Jan 1, 1924

By A. A. Rauth

In this paper, the author derives a series of formulas from basic principles and illustrates the application of these formulas to practical grinding charge problems. The paper establishes the nearly proportional relationship of mill power to charge level and shows how this relationship can be used to advantage in the design, manufacture and operation of grinding mills. The procedures outlined offer a rapid means of anticipating the power requirements for a given charge or determining makeup charges for a given power reading. The theories which have been developed concerning the dynamics of grinding have been motivated largely by the desire to derive workable formulas for the accurate determination of grinding mill power. This accurate determination has always been handicapped by the large number of variables to be considered, some of which are mill diameter, length, speed, liner design, grinding charge and material density, volumetric mill loading, internal friction, and charge size and gradation. In efforts to determine mill power, attempts have been made to utilize torque concepts. The formulas derived consider the grinding mass as a rigid body and utilize factors that are based on empirical data so that the movement of the charge within the mill is compensated for. These formulas are of principal interest to the mill designer since he is charged with the responsibility of analyzing all of the variables and from them predicting a mill size and a motor size which are compatible both with each other and with the grinding job for which they were intended. The mill operator, on the other hand, has an entirely different problem. The mill dimensions are already established and so is the driving motor. The operator's main concern is to obtain maximum performance from the mill he already has. For him, the many variables which perplex the mill designer are fixed values. Mill diameter, length and speed are set and, to a large extent, so are the conditions inside the mill from which the torque formula advocates derive their empirical data. It is conceivable that if the major mill dimensions which affect power demand are held constant, and if the variables influencing empirical factors are held fairly constant, as they are in an operating mill, then the only major variable remaining which affects power is the level of the charge itself. Under this condition.

Jan 1, 1970

By William J. Coulter

WITHIN the United States the problem of meeting maximum production by our metal mines has been solved by: (1) Conservation of man power by mechanization. (2) Increasing man-power efficiency as expressed in tons per man-shift by the adoption of new and more efficient methods. (3) Production from submarginal properties made possible by some form of government subsidy. (4) Selective mining of high-grade areas. (5) Drawing on broken ore reserves and reducing advanced development work to a minimum. (6) Making maximum use of available equipment. (7) Repairing equipment that normally would be replaced. (8) Working a seven-day week on a three-shift basis to get maximum use of equipment and man power. (9) Adoption of incentive plans to increase maximum efficiency and unit production. (10) Important advancement in metallurgy, resulting in larger recoveries. (11) Improvements in safety, health, and general working and living condi-

Jan 1, 1945

By Georges Millot

USUALLY the search for clays is left to chance in unexplored areas. A local working by the inhabitants or an outcrop is often the only guide. If the conditions of genesis of clays were always known, a set of general rules could be drawn up that would apply to this search. For example, a certain type of clay might be found wherever the sediment indicated a favorable environment. This paper sums up the considerable amount of knowledge that has been accumulated about the genesis of sedimentary days and offers some rules to be observed in prospecting for new clays. ANALYTICAL STUDY OF SEDIMENTARY CLAYS Clays may be found in many formations, both recent and ancient. All the intermediums exist between the deep-sea deposit and the mud deposited by a stream. In order to find out whether the nature of clay deposits depends on the environments in which they were formed, the samples used in the investigation described herein were very carefully chosen from: (1) ancient sedimentary series (a few from recent ones), (2) zones where conditions of genesis are typical. Ancient Formations Ancient formations were chosen because they are less difficult to sample than the bottom sediments of present-day lakes and seas. Moreover, a geo- logical section makes it possible to define the conditions of genesis of a deposit based on its facies, fossils, stratigraphic relations, and paleography. A present-day deposit is defined only by its aspect at the moment. Its previous history may have caused mixtures, alterations, and changes of environment, which escape detection. Typical Conditions of Genesis Samples from ancient deposits were taken from zones where typical conditions of genesis prevailed. Only clays from marine, lagoonal, and lacustrine environs are concerned in this study because the nature of the original en- vironments could be affirmed. In this way an inventory of the nature of sedimentary clays has been made for rocks formed in typical and individual environments; therefore the extent of the results that may be drawn from such a study will need discussion.

Jan 1, 1952

By Zay, Jeffries

THE effect of thoria (ThO2) on grain growth in tungsten was discussed in some detail in a paper presented before this Institute by one, of the authors in 1918.1 In that paper it " was assumed that the, thoria was present in the tungsten entirely as a mechanical mixture. There was no indication in the experiments described that even a trace of the thoria was in solid solution in the tungsten. Langmuir,2 however, observed that thoriated-tungsten filaments under certain conditions showed electron emissions many thousand times greater than unthoriated tungsten at the same temperature. He concluded from his studies that a slight amount of the thoria had dissociated on heating the filament to a temperature near 220°. C. At this temperature and higher, part of the thorium diffuses to the surface of the filament where it evaporates at. a much faster rate relatively, than the tungsten, and also at a rate, nearly as fast as it is brought to the surface by diffusion: If the temperature is lowered to say 1800°,. C., diffusion of the thorium atoms to the surface is more rapid than evaporation, sown adsorbed film of thorium atoms is produced on the surface of the tungsten filament. The electron emission is governed by the outside layer of atoms so the emission from such a filament might be expected to approxi¬mate that of a thorium filament at the same temperature. PRESENCE OF METALLIC THORIUM IN THORIATED TUNGSTEN If the filament containing the adsorbed film of thorium. is heated to a sufficiently high temperature, the thorium atoms evaporate: rapidly and the electron emission becomes more nearly that of tungsten. On cooling again to 1800° C., or thereabouts, the emission 'builds up gradually to a maximum. The filament containing the adsorbed layer of thorium atoms is said to be "activated." By studying the rates of activation under different conditions of prior thermal treatment and at different temperatures, Langmuir was able to arrive at an estimate of the

Jan 1, 1927

By Philip E. LaMoreaux

Fluoride, generally less than 0.5 ppm, is present in ground water from rocks of Paleozoic age and older, in northern and eastern Alabama. Some of the water-bearing formations in the Coastal Plain area of the State yield water with as much as 6.8 ppm fluoride.

Jan 1, 1950

By Jed H. Mosgrove

Ventilation is the method of producing, conducting, and distributing a constant current of fresh air through mine workings and returning the impure air to the outside atmosphere. Without ventilation no operations are possible in an underground mine. Therefore it is the most important single phase of mining, one on which everything else depends. A good ventilation system, therefore, must be correctly designed, properly conducted as the workings advance, and continually checked to make sure it is functioning correctly. Good air is essential for men to comfortably and safely perform their work. It is also essential to dilute, render harmless, and sweep the mine of any explosive fumes and the gases that are released in varying degrees by all coal seams and the rock strata in which they are contained. GENERAL The body of air that is being moved through the mine, known as the ventilating current, must have a definite way to enter and leave the mine. In other words, there must be a definite intake and return. The main consideration is to get the proper amount of good quality air to the working faces where it is needed. Inasmuch as the mine is divided into sections with interconnecting corridors, known as entries, it is necessary that there be a proper means of conducting the air to the proper points. As a simple explanation of a mine, consider a long tube and think of it in terms of a mine entry ill which the air must pass. The tube must have at least two openings before air can travel through it and this is the same for coal mine entries. The problem in ventilation is to find some means that will cause the air in the tube to flow from one end to the other. The only possible way to do this is to cause greater pressure at one end of the tube than at the other. Air at the end with the greatest pressure would then, of course, flow to the en which has the least pressure. Mine

Jan 1, 1973

By H. M. Roche

MAGNETITE mining and milling in the Eastern States was sharply curtailed in 1938, production showing a decrease of 36 per cent from 1936 and 57 per cent from 1937. Six mines, one in Pennsylvania, two in New York, and three in New Jersey were in operation, either part or full time, during the year. In recent years ten Eastern magnetite mines have been more or less active but since the World War the market for Eastern ores- has been spotty. The scrapping of Eastern merchant pig iron furnaces, imports of cheaply mined duty-free foreign ore, and high freight cost have been contributing factors.

Jan 1, 1939

By Charles Hart

The art of electric smelting came with the turn of the present century and owes its existence to the introduction of alternating current, which found its first wide use in the establishment of the great power plants at Niagara Falls, N. Y. Prior to that time current was largely direct. The furnaces were electrolytic in nature and found their first metallurgical use in the production of aluminum, and this process still prevails. The normal production of pig iron up to that time was carried on in blast furnaces in which charcoal, coke and anthracite were used as the fuel. This new electric process called for sufficient carbonaceous material to reduce the oxides and impregnate the pig iron with sufficient carbon, but the remainder of the energy was to be supplied by electric power. The chemical reactions are essentially the same in electric smelting as obtains in the older blast furnace. All of these data are so well known in both methods as to need no discussion at this time, for they can be found in scientific : publications and books written during the first two decades of this century. Types of Furnaces The 40 years devoted to the practice of electric smelting may be divided into two . periods of 20 years each. The first was devoted to experimentation with furnace types and with many publications on theories and processes. The second half of this term was devoted to perfecting the types of furnaces and their active commercial operation. The arc furnace may be found in three types: (1) the direct-heating arc furnace with the positive electrode included in the bottom and the other electrode suspended above; (2) the independent arc furnace with its electrodes entirely above the charge, which of necessity depends upon heat reflected from the roof; (3) the direct-heating series arc furnace equipped with two or more electrodes suspended from the roof. Of these three types, only the last is used in electric smelting of iron ore at the present time. The elimination of the other types automatically removed many of the early designs, to the end that there are now only two general types in operation: (I) the " Electrometalls" or high-shaft furnace of Sweden, and (2) the low-shaft or pit-type furnace as offered by Tysland-Hole and Siemens-Halske. The "Electrometalls" furnace takes its name from the corporation formed by the engineers that had undertaken its perfection. After trying several designs they brought forward the furnace shown in Fig. I, which by the way is the highest development of this type of furnace as of today.l Note the trend in the lines, which have kept pace with modern blast-furnace design. The high-shaft furnace lends itself to skip filling and is fitted with tuyeres immediately under the crucible roof, whereby the gases are recycled and the roof preserved. The failure of the Electrometalls furnace in Norway, because of its inability to meet

Jan 1, 1941